Used Blow Up for sale (1,975)

Condition: like new (used), Year of construction: 2013, BLOW EXTRUDER HDPE Model EuroTruder 75 Made by Euro-Stel, Belgium YOM 2013 extruder: diameter 75x28 D - with neck sweder and granulate hopper Gbodpfx Agjwivdkjbeg mold is not included EXCELLENT CONDITION

Condition: used, Year of construction: 2017, Overview The blowmoulder was built in 2017 by the manufacturer SIPA. The machine is until February 2026 in operation and can be visited. It is used in a mineral water factory. The blowing machine is in a very good condition due to regular maintenance. Technical data  Nominal capacity: 18.000 bph Nr. of moulds: 8 Last used formats: 0,5l 1,0l 1,5l Neck type: PCO-28-1810 Incl. preform feeding system Incl. preform cooling system Min. - max. bottle diameter: 50 - 125 mm Min. - max. bottle height: 80 - 349 mm Gedpox Ti R Ejfx Agbobg

Condition: used, Year of construction: 1966, shaft length 15 - 130 mm wire diameter 6 - 12 mm length of wire blank max. 170 mm Gsdpfx Ajv Sva Eegbjbg capacity/output with closed mould, adjustable 100 /min capacity/output with open mould, adjustable 67 /min Weight 12,5 t dimensions of the machine (WxDxH) 2,3 x 4,0 x 1,6 m combined double-pressure cold header press for jaws and closed moulds maximum wire diameter for high tensile bolts und carriage bolts 10 mm maximum wire diameter for mild steel bolts and rivets 12 mm wire diameter range 6 - 12 mm minimum and maximum shaft length 15 - 130 mm maximum length of wire blank 170 mm capacity/output with closed mould, adjustable - 100 St/min capacity/output with open mould - 67 St/min power requirement 15,0 kW mould dimensions - jaw dimensions 54 x 54 mm

Condition: good (used), Year of construction: 1976, wire diameter range: a) single wire: 2,2 - 3,8 mm b) double wire: 2,2 - 3,4 mm Gbedpfed Im Nusx Agbjg nail length: 10 - 80 mm output: 300/600 nails/min.

Condition: used, Year of construction: 2007, This is a Sidel SBO 4 blow moulder, it’s designed to receive preforms of 38 mm neck size caps and blow mould the bottles . The speed of the machine is at 6,000 bottles per hour on 2 litre round bottles . The year of manufacture is 2007 and the condition is very good. The is delivered with the pre forms hopper and elevator. Capacity: 6000 b/h Volumes: 250-500-1000-2000 ml Neck Size of preforms: 38 mm Format: Round bottles Air consumption: 11 bar Gbjdpfx Agjx Tdahebsg Controls: SIEMENS SIMATIC MULTI TOUCH PANNEL Available: Immediately

Condition: used, mileage: 522,000 km, power: 279 kW (379.33 HP), first registration: 09/2009, fuel type: diesel, tire size: 385/55 R 22.5, axle configuration: 10x4, wheelbase: 7,730 mm, fuel: diesel, driver cabin: day cab, gearing type: mechanical, emission class: euro5, suspension: other, total length: 10,000 mm, total width: 2,550 mm, Year of construction: 2009, Equipment: ABS, air conditioning, central locking, cruise control, electric window regulation, = Additional Options and Accessories = - Aluminium fuel tank - Digital tachograph - Air suspension - Radio/CD player - Sun visor - Power take-off (PTO) = Further Information = Technical Information Number of cylinders: 6 Engine displacement: 11,705 cc Gbedsx Ahz Ejpfx Agbsg Axle Configuration Axle 1: Tire size: 385/55 R 22.5; Steered; Left tire tread: 35%; Right tire tread: 35%; Suspension: leaf spring Axle 2: Tire size: 385/55 R 22.5; Steered; Left tire tread: 50%; Right tire tread: 50%; Suspension: leaf spring Axle 3: Tire size: 295/80 R 22.5; Twin tires; Inner left tread: 40%; Outer left tread: 40%; Inner right tread: 40%; Outer right tread: 40%; Reduction: single reduction; Suspension: air suspension Axle 4: Tire size: 295/80 R 22.5; Twin tires; Inner left tread: 30%; Outer left tread: 30%; Inner right tread: 30%; Outer right tread: 30%; Reduction: single reduction; Suspension: air suspension Axle 5: Tire size: 435/50 R 22.5; Left tire tread: 25%; Right tire tread: 25%; Suspension: air suspension Weights Unladen weight: 17,860 kg Payload: 32,140 kg Gross vehicle weight (GVW): 50,000 kg Condition Damages: none

Condition: good (used), Year of construction: 1989, functionality: fully functional, To preforms. Four-station rotary machine (injection, stretching, blowing, ejection) designed for producing PET, PP, PS, etc. containers (One-step ISBM). PET bottles 200–500 ml: 2,000–4,000 units/hour depending on cavity configuration and design. Compatible materials: PET, PP, PC, PS, PEN. Standard configuration: 4 stations, 1–2 injection cavities, 2–4 blow cavities. Injection clamping force: 80–100 t. Blow clamping force: 20–30 t. Total heating power: 28 kW. Main motor: 45 kW. Gbsdjx Swqqopfx Agbsg

Condition: used, Year of construction: 2022, functionality: fully functional, machine/vehicle number: HY-43, screw diameter: 110 mm, total width: 2,500 mm, total length: 8,500 mm, total height: 9,500 mm, power: 350 kW (475.87 HP), Equipment: documentation/manual, The two-layer blow molding machine is a new generation of plastic extrusion blow molding equipment. It is mainly used for molding kayaks, canoes, surfboards, and other large hollow plastic products. The machine uses a motor designed to deliver high torque and sufficient power for material cutting. The molten plastic is extruded into a storage die head. When the material reaches the preset volume, the wall-thickness control system continuously adjusts the opening ratio. Gjdpfxjx R R Igs Agbebg The extruded material is formed into a parison, which is then molded into the final product.

Condition: used, DM-01225-PET-Blowing Semi-automatic PET bottle blowing machine Capacity: 1,000 BPH 2 units of blowing machines Gbsdpfxex I Rclo Agbog 1 preform heating tunnel Equipped with 2 x 0.5 L bottle mold Capacity: 1,000 pcs/hour, Cavities: 2 x 2 for 500 ml bottles Air pressure compressor Air dryer Donalcon air filters

Condition: used, Year of construction: 2004, Bottling Blower, PET Blowing Machine KRONES Including (preform tipper, preform hopper, preform unscrambler, chiller, air conveyors for bottle transport, year 2004) Model: Contiform S8 Year: 2004 Speed: 13,600 BPH Number of cavities: 8 Machine dimensions: Carousel 2000 mm x 2000 mm x 3000 mm (h) Oven 4000 mm x 2000 mm x 3000 mm Gbjdjwuyt Tepfx Agbsg Safety protections

Condition: used, Year of construction: 2004, Overview This stretch blow moulding machine was manufactured in 2004 by German company KRONES. The machine is a CONTIFORM S8, designed for PET bottle production and configured for PCO 1881 and Alaska neck finishes. The blow moulder is immediately available. Technical data  Capacity: Max. 13,600 bph Formats: 0.50 L 1.00 L 1.50 L Neck finish: PCO 1881 Alaska Number of cavities: 8 moulds Operating hours: Approx. 35,000 h Scope of Delivery  KRONES CONTIFORM S8 stretch blow moulding machine Preform hopper and feeder Chiller 6 sets of moulds Spare parts Gbjdpfxex Iftxe Agbsg

Condition: used, Year of construction: 2009, Used Blow Molding Machine Contiform This used Krones Contiform S14 blow molding machine is engineered for high-output PET bottle production in modern beverage manufacturing. With a maximum speed of up to 25,000 bottles per hour, it is an excellent choice for businesses looking to expand capacity or upgrade a used bottling line with reliable second hand industrial packaging equipment. The machine is equipped with a Siemens PLC and a Krones HMI for robust automation and operator-friendly control. Neck-handling transfer ensures stable bottle handling across formats, while the rotary architecture delivers consistent performance for beverage production. Manufactured by Krones, a global leader in beverage production technology, this model supports PET containers and is suitable for a wide range of products including still and sparkling water, soft drinks, milk, oil, beer, wine, and spirits. The current setup is optimized for 1.5L format and a maximum container height of 320 mm, making it a versatile asset for PET bottle processing in integrated bottling equipment lines. Technical Specifications & Performance Data Manufacturer: Krones Model series: Contiform Model code: S14 Year of manufacture: 2009 Maximum speed: 25,000 bottles/hour Container material: PET Current format: 1.5L Maximum container height: 320 mm Worktable height: 1470 mm Type: Rotary Transfer type: Neck-handling Neck finish: Alaska Number of cavities (molds): 14 Number of spindles: 7 Number of grippers (inlet/outlet): 7 Work direction: Counterclockwise Electrical supply: 400 V, 3 PH + N, 50 Hz Rated current: 313 A Advanced Automation & Control Systems The machine features a Siemens PLC for reliable process control and a Krones HMI for intuitive operation, recipe management, and diagnostics. The electrical configuration at 400 V and 50 Hz with 3 PH + N supports stable, industrial-grade performance. Safety guarding and interlocked access points facilitate secure operation during production and changeovers. Neck-handling design contributes to smoother format adjustments and reduced container scuffing. Production Line Integration Capabilities Gbodpfx Agsx H Tgdebjg This Krones Contiform S14 can operate as a standalone blow molder or be integrated into a complete beverage production line. It interfaces smoothly with preform handling systems, high- and low-pressure air utilities, and downstream conveyors leading to filling, labeling, and packaging machinery. The rotary platform and neck-handling transfer provide compatibility across typical PET bottle sizes, including 1.5L and other common formats used in water and soft drink applications. Machine Condition & Maintenance History The unit is available in multiple supply options: as-is (seen and liked), refurbished and guaranteed, or ready for operation with compatible spare parts.

Condition: new, Year of construction: 2025, New BKS 400 and BKS 401 impact bars for, for example, the SBM 10/6/4 Export or Tesab RK 623, chrome-plated cast iron, dimensions approx. 610 x 264 x 123 mm, approx. 103-110 kg. Available for immediate delivery, subject to prior sale. Gbodpfx Ajq Ecw Hsgbeg

Condition: good (used), Year of construction: 2017, functionality: fully functional, LINEAR PET BLOWING MACHINE SET with auxiliary equipment AC ARCOR - multiBlow2 - 2017 Speed: 1,5L - 6000 Cavities: 4 Formats: 0,1 - 3,0L AUXILARY EQUIP 1. Chiller - M.T.A S.p.A - TAE EVO 051 2. LOW Pressure compressor - SHAMAL 45kw 3. High Pressure compressor - KAESER Booster N 753 - G 13 bar / 40 bar" 4. Air Dryer Gjdpfxjquuvrs Agbjbg 5. Receiver tank - Low pressure - MAX 16Bar 6. Receiver tank - High pressure - MAX 45Bar

Condition: used, Year of construction: 1990, functionality: fully functional, machine/vehicle number: M08E/9065, Offer Number: M08E/9065 Machinetype: 5 die - 5 blow progressive header Info: bushing cut-off Make: SAKAMURA Type: BPF540 Constr. year: 1990/09 Gjdpfxjx Igg To Agbsbg diameter range: 23 mm number of dies: 5 number of stations (incl. cut off): 6 cutting length: 175 mm shaft length under head: 130 mm output - pieces/min: 86 - 130 press power: 220 to Location: Europe

Condition: like new (used), functionality: fully functional, machine/vehicle number: SBO 6/10, Sidel Stretch Blow Moulding Machine Max. output: 6.000 bottles/hour. Max. bottle size: 3.000 cc. Blow stations: 6. Machine is in very good conditioning and well maintained. GENERAL INFORMATION The SBO 6/10 has 6 molds and 10 heating modules. Will work with a wide range of bottle sizes and styles from 0.25 to 3 liters. Sidel 2-step ^PET stretch-blow molders require previously manufactured preforms be supplied to the machine. Separating the bottle manufacturing and preform manufacturing processes allow production to be optimized, provide greater flexibility of operation and use, and provide higher production output rates and yield. MAXIMUM PREFORM DIMENSIONS Neck height 9 – 41 mm (measured from bottom of support ring) Minimum inside diameter of neck 19 mm Maximum outside diameter of neck 34 mm Preform support ring diameter 29 – 51 mm Maximum preform length 210 mm MAXIMUM BOTTLE DIMENSIONS Maximum bottle diameter 130 mm Maximum bottle height 380 mm Godpfjg Ailcox Agbebg Bottle capacity 0.25 – 3 liters AVERAGE PREFORM WEIGHTS (non carbonated and carbonated liquids) 0.25 liter bottle 14-20 grams 0.50 liter bottle 20-33 grams 1.00 liter bottle 26-40 grams 1.50 liter bottle 35-51 grams 2.00 liter bottle 44-58 grams 3.00 liter bottle 68-84 grams BLOW WHEEL Height 3.5 meters Number of molds 6 Closing force 10 tons Item height (under neck) at outfeed 1.4 meters approximately Machine DC drive motor power 4 KW HEAT CONDITIONING Height 2 meters Number of oven heating units 10 Number of heating zones per unit 8 Maximum power 170 KW ELECTRICAL USAGE Maximum supplied power 200 KW Average consumption 100-150 KW/hr (varies per bottle being produced) COMPRESSED AIR Supplied power from 7-35 bar Pressure 7 bar Flow rate 50-100 Nm3/hr (varies per bottle being produced) Blow pressure – champagne base up to 25 bar Blow flow rate – champagne base 110-550 Nm3/hr Blow pressure – petaloid base up to 35 bar Blow flow rate – petaloid base 155-770 Nm3/hr CHILLED WATER Temperature 10-12 degrees Centigrade Pressure 5-6 bar Flow rate up to 6 cubic meters/hour Kcal to be removed up to 16,000 Kcal/hour WEIGHT Blow wheel with molds 8 tons Heat conditioning unit 2.2 tons Preform feeder 0.65 tons Electrical cabinet 0.85 tons PREFORM HEAT CONDITONING The preforms are transferred neck up to the heat conditioning device. This unit continuously insures the preforms are inverted before passing, neck down, in front of the heating units and then inverts them again. During the heating phase, the preforms are rotated and their necks protected from the heat in order to optimize the distribution of heat without deforming the neck. Heating is insured by 10 heat modules. Each unit can accommodate up to 8 infrared lamps stacked horizontally whose ends are air cooled. The heating power of 8 zones, corresponding to the 8 rows of lamps, can be controlled in order to optimize the heat profile. These zones are regulated on all SBO Models. After heating, a control by infra-red camera of preform temperature enables regulation of the zones under control, thus insuring maintenance of the required temperature.

Condition: ready for operation (used), Year of construction: 1993, functionality: fully functional, product height (max.): 380 mm, workpiece diameter (max.): 130 mm, production capacity: 7,200 unit/h, TECHNICAL DETAILS Number of cavities: 6 Capacity with standard bottles: up to 7,200 bph Product formats Bottle volume: 0.25 – 3.0 L Max. bottle height: 380 mm Max. bottle diameter: 130 mm Preform dimensions Max. preform length: 210 mm Neck inner diameter: 34 mm MACHINE DETAILS Dimensions & Weight Blow module dimensions: 2,000 x 2,200 x 2,200 mm Blow module weight: 8,000 kg Oven dimensions: 3,000 x 1,100 x 2,100 mm Oven weight: 2,000 kg Control cabinet dimensions: 1,500 x 1,000 x 2,100 mm Control cabinet weight: 1,000 kg Transformer 415V / 380V dimensions: 1,000 x 500 x 2,000 mm Transformer weight: 500 kg Preform hopper and conveyor dimensions: 3,000 x 1,500 x 3,500 mm Preform hopper and conveyor weight: 600 kg Preform feeder dimensions: 2,000 x 2,500 mm Preform feeder weight: 250 kg Infeed guide rail length: 2,000 mm Power supply Total power: 142 kW Mains connection: 380/420 V +/- 10%, 50 Hz +/- 1% Cooling water Cooling capacity: 16,000 kcal/h Water temperature: 10 – 12°C Flow rate: up to 6.0 m³/h Water pressure: 5 – 6 bar Gbedpsx A Uu Eefx Agbjg Compressed air Service air pressure: 7 bar Service air flow: 50 – 100 Nm³/h Blowing air pressure: up to 35 bar Blowing air flow for 0.25 – 3.0 L: 155 – 770 Nm³/h EQUIPMENT Transformer 415V / 380V Preform hopper and conveyor Preform feeder Infeed guides Adaptation to other voltages possible

Condition: used, Year of construction: 2004, Blow Molding Machine Contiform – Overview This used Krones Contiform S8 blow molding machine is engineered for high-efficiency production of PET bottles in modern beverage and industrial packaging operations. With a rotary configuration and robust mechanical design, it reaches up to 13,000 bottles per hour, supporting scalable output for medium to high-speed lines. The machine is optimized for PET containers and is suitable for diverse beverage production environments, including water, beer, wine, spirits, milk, oil, and carbonated soft drinks. Krones engineering ensures excellent reliability, consistent bottle quality, and streamlined changeovers. Designed as a versatile component for a used bottling line or as a standalone blow molder, this second hand system delivers precise preform handling and stable heating, coupled with efficient blowing performance. It features an Alaska thread finish, an 8-cavity configuration, and a clockwise work direction, making it a proven choice for beverage production and industrial packaging where uptime and repeatability are critical. Technical Specifications & Performance Data Manufacturer: Krones Model: Contiform S8 Manufacturing year: 2004 Configuration: Rotary Maximum speed: 13,000 bph Container material: PET Current bottle format: 0.5L No. of cavities: 8 Thread/neck finish: Alaska Max container height: 350 mm No. of grippers (inlet–outlet): 6 No. of mandrels: 180 Work direction: Clockwise Gbodpox H Tf Tofx Agbog Working plane height: 1470 mm Electrical supply: 400 V, 3-phase, 50 Hz Operating current: 331 A Operating pressure: 40 bar PLC: Siemens HMI: Krones Advanced Automation & Control Systems The Contiform S8 integrates a Siemens PLC for robust automation and process control, complemented by a Krones HMI for intuitive operation and fast diagnostics. The control architecture supports stable preform heating profiles, accurate blowing cycles, and reliable handling of PET preforms and bottles. Safety interlocks and operator protections are integrated into the guarding and access points to support consistent production with minimized downtime. Production Line Integration Capabilities This blow molding machine can operate as a standalone unit or integrate seamlessly into a complete used bottling line. It interfaces effectively with upstream preform feeding systems and downstream air conveyors, rinsers, fillers, and labelers. Format changeovers are streamlined around the 8-cavity rotary platform, and the Alaska neck finish provides compatibility for a wide range of closures and filling monoblocks across beverage production. Machine Condition & Maintenance History The machine is available in multiple supply configurations: as-is, refurbished and guaranteed, or ready for operation with compatible spare parts.

Condition: new, Year of construction: 2024, We offer subject to prior sales: -4- pieces blow bars , model HAZ 790, high chrome, each approx. 107 kg, directly available, subject to prior sales. Gbjdpfellvyrox Agbeg

Condition: used, Year of construction: 2017, Rotary stretch blow molding machine for blowing PET bottles from preforms. Preforms are poured from a container into the feed hopper via a tilting device. From there, the preforms are fed out via an ascending belt with electronically controlled speed and are transported to the blow molding machine in a uniform orientation via a chute and loading star wheel. The shape and size of the preforms are checked and defective preforms are ejected before they are fed to the heating boxes via a mechanical star wheel. In the heating boxes, the preforms are preheated with infrared lamps. They are continuously rotated to ensure symmetrical heat distribution. Fans prevent overheating on the outside. Finally, the preform temperatures are checked using an optical pyrometer. Grippers feed the preforms to the blow wheel and remove them from it. The blow molding unit works with “crocodile molds,” in which expansion along the longitudinal axis is supported by a stretching rod. The preforms are then blown into PET bottles. The stretch-blown bottles are removed from the cavities by grippers and conveyed to the ejector. Additional title: rotational molding machine Capacity: 18000 bo/h Number of cavities: 8 pcs. Number of bottles to be ejected per stop: 202 pcs. Gjdpexyktljfx Agbebg Blow pressure: 30 bar Power: 58 kW Voltage: 400 V Frequency: 50 Hz Water: 4 bar Compressed air: 360 Nm3/h at 7 bar Weight: 16700 kg Formats: 0.5 l; 1.0 l; 1.5 l PET bottles Features: Preform feed hopper with tilting device for containers, inclined belt conveyor for preforms, preform inspection, heating boxes, blow wheel; bottle ejector; visualization on screen

Condition: used, Year of construction: 1980, functionality: fully functional, machine/vehicle number: M08L/8554, Offer Number: M08L/8554 Machinetype: 4 die - 4 blow transfer header Gbodewi Sxdspfx Agbjg Info: bushing cut-off , PKO , IFO Make: MALMEDIE Type: KL34 Constr. year: 1980 diameter range: 6-14 mm number of dies: 4 number of stations (incl. cut off): 5 cutting length: 280 mm shaft length under head: 220(260) mm output - pieces/min: 40-75 press power: 100 t Location: In our warehouse

Condition: reconditioned (used), Year of construction: 2012, SB 3000.5E linear blow molding machine, including: New modular heating system, Preform feeder, easy and quick mold change system, electric stretching system, touch screen panel, smooth performance adjustment, cracked bottle elimination function Single-nest machine prepared for blowing 5-liter bottles. The machine after a major renovation at Dynaplast, all operating components were replaced and the drive of the bottle ejection basket was changed, instead of the angular gear, a belt transmission with a servo drive was used, which allows for smoother operation of the component. The preform is also stretched using a belt transmission and driven by a servo drive, which allows for smooth speed adjustment from the operator panel, (we can smoothly adjust the speed of the stretching rods) The price given is for the machine without the mold visible in the photos, it is possible to resell the visible 5L mold Gbjdpst Uap Ssfx Agbsg

Condition: like new (used), 8 impact bars for HAZEMAG APK50 mill Gjdev N T Ihepfx Agbsbg Model: HAZ971 Each weight: approx. 146 kg

Condition: used, Year of construction: 2014, functionality: fully functional, machine/vehicle number: M08L/8828, Offer Number: M08L/8828 Gsdswi Tdujpfx Agbobg Machinetype: 3 die - 3 blow transfer header Info: with PKO Make: JERN YAO Type: JBF-10B3S Constr. year: 2014 diameter range: 3-8 mm number of dies: 3 number of stations (incl. cut off): 4 cutting length: 70 mm shaft length under head: 12-60 mm output - pieces/min: 300 press power: 28 t Location: In our warehouse

Condition: reconditioned (used), Year of construction: 2006, functionality: fully functional, machine/vehicle number: SB 8015, SB 8000 linear blow molding machine, serial number 8015, year of production 2006 with a nominal capacity of 7200 bph (approx. 6000 bph with a 2.0l bottle), Gbedpfx Agjt T Txqjbsg Machine after general renovation, in very good technical condition, all operating components replaced. The machine set includes: Preform feeder, easy and quick mold change system, electric stretching system, mechanical lifting system, powered by electric motors for a closing system with pressure compensation, 6-inch touch panel, smooth regulation of capacity in the range of 5000-7400 bph, function of eliminating deformed molds and cracked bottles. The machine is adapted to the PCO 1810 preform, it is possible to retool the machine for another preform. The machine is sold without blow molds, we can make molds according to the customer's design adapted to our machine.