Used Baler for sale (233)

Condition: reconditioned (used), Year of construction: 2005, operating hours: 30,408 h, functionality: fully functional, pressing force: 50 t, filling opening width: 1,100 mm, filling opening length: 1,250 mm, bale width: 1,100 mm, bale height: 720 mm, bale weight: 550 kg, overall weight: 16,000 kg, oil tank capacity: 600 l, year of last overhaul: 2024, Technical data baler: Manufacturer Presona AB Type LP 50 EH1 Year of construction 2005 Operating hours 30,408 hours, as of April Number of pressed bales 198,059 as of April Pressing force main press 50 tonnes Specific pressing force 63 N/cm² Theoretical throughput capacity 530 m³/hour Throughput capacity under operating conditions 260 m³/hour Dimensions of feed chute 1,250 x 1,100 mm Bale chamber volume 2.2 m³ Bale dimensions 1,100 x 720 mm, variable length Drive power 22 kW Tying 5-fold vertical, fully automatic Throughput rates with a bulk density of 30 kg/cbm 6 up to 7 tonnes/hour Bulk weight of 50 kg/cbm 7 up to 9 tonnes/hour Bulk weight of 100 kg/cbm 11 up to 14 tonnes/hour Bale density (paper/newspapers) 400 to 550 kg/m³ Hydraulic oil tank capacity 600 litres PLC control Telemecanique TSX Micro Schneider Magelis control panel Effective transport dimensions excl. baler 8,125 x 2,300 x 3,000 mm (L x W x H) Transport weight press approx. 16 tonnes Condition of the baler: The machine was partial overhauled in our workshop and general maintenance work was carried out. After completion of the overhaul work, the press was tested during operation and is available for sale at short notice. The following overhaul work was carried out: General work: Machine cleaned, derusted, primed, partially painted Wire entry marks in the press channel feed-throughs welded shut and smoothed Nodou Thhrepfx Afaowf Hydraulic unit: Hydraulic oil tank emptied, tank cleaned, new oil filled Oil filter and air filter replaced Leaky oil sight glass on hydraulic oil tank replaced All hydraulic hoses replaced Electrics: English language installed in the programme menu Two key switches in the control panel replaced Control cabinet replaced Signal lamp on the control cabinet replaced Flaps end switch replaced Electrical system of the turbulator replaced, connected and tested Press ram: All four rollers removed from the press ram and replaced Main hydraulic cylinder dismantled, disassembled and partially overhauled, cylinder tube honed, complete seal set replaced, leak test performed All plastic wear pads on the press ram replaced Pre-press: Both bearings on the pre-press shaft replaced. Both hydraulic cylinders dismantled, disassembled and partially overhauled, both cylinder tubes honed, complete seal sets replaced, leak test performed. Scraper flap on the pre-press replaced. Binding system: Two complete needles with wire deflection rollers replaced Needles adjusted and set All wire deflection rollers in the needle heads replaced Drill fingers replaced Two drill shafts replaced All 8 wear plates on the Drillomat, under the drill fingers, replaced Scope of delivery: Only the baler will be sold. The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: reconditioned (used), Year of construction: 2002, operating hours: 44,590 h, functionality: fully functional, pressing force: 200 t, filling opening width: 1,020 mm, filling opening length: 2,000 mm, bale width: 1,100 mm, bale height: 1,100 mm, oil tank capacity: 3,100 l, power: 150 kW (203.94 HP), year of last overhaul: 2025, Technical data baler: Manufacturer MACPRESSE EUROPA S.R.L. Typ 112 Year of construction 2002, partially refurbished in December 2025 Operating hours 44,590 hours, stand December 2025 Press power main press 200 tons Specific press capacity 16,5 kg/cm² Feed channel 2,000 x 1,020 mm Filling volume 2,65 cm³ Theoretic throughput rate 795 m³/h Bale size 1,100 x 1,100 mm, length variable Driving motor 2 x 75 kW Tying system 5-fold horizontal, full automatic Throughput rate at MSW approx. 48 up to 54 tons/h, depends on material Volume hydraulic oil tank 3,100 l Machine weight baler approx. 50,8 tons Scope of delifery: 1 piece baler MACPRESSE, type 111A 1 operating manual with CE declaration, electrical and hydraulic circuit diagram Comments: Nwjdex Dnb Ujpfx Afasf The machine was serviced and partially overhauled in our workshop. The following work was carried out and parts replaced: • Hydraulic oil tank emptied and cleaned • Oil and air filters replaced • New hydraulic oil filled • All hydraulic hoses replaced • Press ram dismantled, broken down into individual parts, mechanics made operational • Front two main rollers replaced • Knives on the press ram replaced • Main hydraulic cylinder dismantled, disassembled, cylinder tube and piston rod checked, complete seal set replaced • Counter knife in the frame replaced • Knife gap adjusted to approx. 3 mm • Upper steel guide rails in the frame on the left and right replaced. • Worn press base cut out, base plate replaced with wear-resistant HARDOX steel. • Binding and twisting unit dismantled, broken down into individual parts, mechanics made functional, all twisting shafts and ball bearings replaced. • All wire rollers in the needle heads replaced • Wire knives cleaned and readjusted, chains greased and tensioned • All wire deflection rollers made operational • All door contact switches replaced • Wirbulator device dismantled, disassembled and made operational • General maintenance work carried out Finally, the press was subjected to a machine test in manual and automatic mode, see our video for the machine function test. The documentation (BA, CE, electrical/hydraulic circuit diagram) is complete. Viewing is possible by appointment. We accept no liability for the technical specifications or any errors.

Condition: reconditioned (used), Year of construction: 2009, operating hours: 22,029 h, functionality: fully functional, pressing force: 80 t, filling opening width: 1,000 mm, filling opening length: 1,400 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 600 kg, overall weight: 16,000 kg, power: 45 kW (61.18 HP), year of last overhaul: 2025, Technical data baler: Manufacturer Avermann Maschinenfabrik GmbH & Co. KG, Germany Type AVOS 1410-45/80 Year of construction 2009 Nsdpfx Aex A U Ncofaewf Operation hours 22,029 hours, as of December 2025 Press power main press 80kN Specific press force 103,9 N/cm² Feed channel 1,400 x 1,000 mm Theoretic cycle time 12 sec Theoretic throughput capacity 300 m³/h Bale size 1,100 x 750 (w x h), the length is variable Drive power 45 kW Connected load 75 kW Tying system 4-fold, vertical, fully automatic Throughput capacity at a bulk weight of 30 kg/cbm approx. 6,0 t/h bulk weight of 50 kg/cbm approx. 10,5 t/h bulk weight of 100 kg/cbm approx. 17,5 t/h Bale weight with a bale length of approx. 1.2 m up to 600 kg, depends on material SPS controller Siemens S7-300 Operating panel pulsotronic Baler dimensions built up 8,610 x 2,400 x 3,835 mm (l x w x h) Transport weight baler approx. 16 t Special equipment: Wear-resistant floor made of HARDOX steel Special press ram for pressing ‘difficult’ materials and loose bulk materials with small grain sizes Control cabinet air conditioning Machine foot elevation 200 mm Remark: The machine was serviced and partially overhauled in our workshop. The following work was carried out and parts replaced: • Dismantling of the press ram, disassembly into individual parts, reconditioning of the mechanics, replacement of the following plastic wear plates and rails: o Plastic wear rails left/right under the press ram o Plastic wear rails left/right above the press ram o Plastic main wear plate (support plate) in the centre under the press ram • Steel guide rails on the left/right in the frame • Replacement of the entire base plate, four-piece, made of wear-resistant HARDOX steel • Wire inlet rails in the press floor newly welded and smoothed • Replacement of the counter blade, two-piece, in the frame • Adjustment of the blade gap to approx. 2.5 mm • Dismantling of the binding and twisting unit, disassembly into individual parts, loosening of the mechanics, replacement of all deep groove ball bearings and axial ball bearings on the twisting shafts, wire blades cleaned and readjusted, chains greased and tensioned • Support roller in front of the twisting shafts replaced • All hydraulic hoses replaced • Oil filter and air filter replaced • Main hydraulic cylinder checked for leaks • The hydraulic oil is only one year old, has been chemically analyzed, is still in good condition, and has therefore not been changed but can continue to be used. • General maintenance work carried out Finally, the press was subjected to a machine test in manual and automatic mode; see video for the machine function test.

Condition: used, Year of construction: 2008, functionality: fully functional, machine/vehicle number: 58900538, input voltage: 380 V, total width: 1,200 mm, total height: 2,300 mm, overall weight: 470 kg, total length: 850 mm, filling opening width: 830 mm, bale width: 830 mm, bale length: 600 mm, bale height: 650 mm, opening width: 830 mm, transport height: 2,300 mm, Machine fully functional, but the press plate is deformed and needs to be straightened (see photo). The machine is sold together with strapping bands for bundling the bales and a sack truck for transporting the bales. Pick-up only, no delivery and no warranty. Nwsdpfxsy Hlg Ne Afaef

Condition: ready for operation (used), Baler Hsm 155 VL Bale dimensions L x W x H: 1100 x 700 x 700 - 950 mm Bale weight: 2000 - 250 kg (Cardboard) Technical data: L x W x H: 1470 x 940 x 2259 / 2439 mm Weight: 950 kg Pressure force 16 tons Power supply: 400 V (three phases) Motor power: 4 kW Bale ejector Nwedpfxera Nrmj Afaof Hsm 155.1 VL baler pressure force 18 tons Price of Hsm 155.1 VL baler - 2600eur Hsm 155.2 vl baler pressure force 16 tons Price of hsm 155.2 vl baler - 2800eur

Condition: good (used), Year of construction: 1981, functionality: fully functional, Equipment: documentation/manual, Automatic channel baler BOA Continu 25 LB + conveyor belt. The baler is in good condition and has been regularly serviced. Recently, the Denison pump underwent a complete overhaul. Fully functional and in continuous operation. Please contact us for further information. Nsdpfxjw S Tv Us Afaowf

Condition: good (used), Year of construction: 2002, functionality: fully functional, Vertical baler HSM VL 600, year of manufacture 2002 Technical specifications: Manufacturer: HSM Model: HSM VL 600 Year of manufacture: 2002 Pressing force: 60 t Drive power: 7.5 kW Cycle time (idle): 37 s Filling height: 1130 mm Nedsyz Sa Sopfx Afaowf Feed opening: 1150 x 735 mm Bale size: 1200 x 1100 x max. 1200 mm Bale weight: 550 kg Machine weight: 3575 kg Materials: Suitable for paper, cardboard, film, car tyres The baler is in good condition and has been inspected and tested. A demonstration video is available on our website or YouTube channel. Operating manual and CE declaration are included. Inspection, including under power, is possible at any time by appointment. Material tests with your own materials can be arranged on request and for a service fee. Please note: All technical details are based on information provided by the manufacturer. We do not accept any liability for the specifications or possible errors. This offer is subject to change, prior sale reserved, and may be withdrawn at any time. Inspections are available by arrangement. Sale is ex works, without warranty or guarantee, and against advance payment only.

Condition: used, Year of construction: 2006, functionality: fully functional, Baler press for bundles approx. 400 kg. Manufacturer: HSM Model: HL 3521 Year of production: 2006 Condition: good Machine has undergone major service. Oil pump replaced. Oil cylinders refurbished. After agreement, can be sold and shipped immediately. Nodpfey A Hu Hox Afajwf

Condition: as good as new (ex-display), Year of construction: 2024, functionality: fully functional, overall weight: 270 kg, warranty duration: 24 months, empty load weight: 265 kg, Robust and compact construction High-quality components with a longer lifespan Njdpfsu Tqmdex Afaowf Above-standard productivity Adjustable bale height (three sizes) Automatic start for efficient compaction Bale trolley for easy transport Material selector for cardboard and plastic Full bale indicator and service indicator Compliance with EN 16500:2014 safety standards

Condition: used, Year of construction: 2005, total width: 1,300 mm, total height: 3,850 mm, total length: 2,200 mm, Empty weight: 1.250 kg Price: On request - Year: 2005 - Documentation available: No - CE marking present: Yes - CE certificate present: No - Serial number: 308 - Transport dimensions: 2200mm x 1300mm x 3850mm (l x w x h) - Transport weight [kg]: 1250kg - Transport packages [pcs.]: 1 Financial information Nodpeyrtcujfx Afajwf VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Yorick Diebels

Condition: used, Year of construction: 2005, total width: 1,300 mm, total height: 3,850 mm, total length: 2,200 mm, Empty weight: 1.250 kg Price: On request - Year: 2005 - Documentation available: No - CE certificate present: No - Serial number: 307 - Transport dimensions: 2200mm x 1300mm x 3850mm (l x w x h) - Transport weight [kg]: 1250kg - Transport packages [pcs.]: 1 Financial information Nwodpfjym Uxtjx Afasf VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Yorick Diebels

Condition: used, Year of construction: 1983, total width: 750 mm, total height: 900 mm, total length: 2,400 mm, Empty weight: 500 kg - Year: 1983 - Documentation available: No - CE certificate present: No - Transport dimensions: 2400mm x 750mm x 900mm (l x w x h) - Transport weight [kg]: 500kg - Transport packages [pcs.]: 1 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Njdpfjxalyyex Afajwf Yorick Diebels

Condition: ready for operation (used), Year of construction: 2003, Baling press Hsm 500.2 vl Fourfold wire tying of bales Bale dimensions (L x W x H, mm): 1200 x 800 x 1000 - 1200 Nwjdpfx Ajra Ak Ejfasf Bale weight (kg): approx. 500 kg Technical data (L x W x H, mm): 1213 x 1824 x 2987 Filling opening (mm): 1200 x 565 Cycle time (sec): 35 Pressing force (T): 54 Power supply (V): 400 (three-phase) Vertical baler Hsm V press 500.2 VL Year of manufacture: 2004-2008 Price: 3,500 EUR Transport height: 2600 mm

Condition: good (used), Manufacturer: Mil-tek Model: 205 TS Machine type: Plastic press / Film press Operating pressure: 8 bar Test pressure: 11 bar Material container: 20 l Drive: pneumatic CE marking: present Quantity: 4 Nwsdpfx Afsyx Skrsasf

Condition: good (used), Year of construction: 2021, functionality: fully functional, pressing force: 58 t, Very good condition, fully functional, low operating hours, year of manufacture 2021, pressing force 58 tons. Nsdpoyzw U Uefx Afajwf New price: seen for €19,500 Pressure cylinder has been dismantled for transport, inspection possible by appointment. Further presses in stock.

Condition: new, Year of construction: 2025, MACHINERY WILL BE BRAND NEW The machinery is available to bale aluminum cans as well as steel cans up to 0.2 mm of the thickness and 3 liters of the volume. All electric-electronic materials will be from Schneider and Siemens Brand. The machine will be fully automatic with PLC control and a touch screen Siemens HMI Simatic Panel with emergency buttons. Machine will be under AYMAS Makina San. Ve Tic. A. S. Guarantee for one (1) year or two thousand five hundred (2.500) operation hours, whichever comes first. There will be an Oil cooling/heating system depending on the operation zone. MB 500 Magnetic Separator and VH (120-250) Vibration Hopper are optional for separating the scrap aluminum and steel cans and for getting rid of the dirt and dust in the scrap. Technical Specifications: Bale Size: 500mm x 330mm x ... Container Dimension (Width x Length x Height): 500mm x 1.000mm x 330mm Capacity Up to 1.000 kg/hour (Aluminum) Up to 2.000 kg/hour (Steel) Bale weighs with a mechanic scale system: 10-20 kg Nwodpfx Aforc Dkqoaof Cycle Time: 30 seconds Top Cover Cylinder Force: 25 tons Main Compression Cylinder Force: 100 tons General Working Pressure: 225 bars Machine Dimensions (Width x Length x Height): 1.100mm x 4.200mm x 2.600mm Electric Motor: 18,5 kW Machine Weight: 5.000 kg

Condition: new, Year of construction: 2025, IMPORTANT: MACHINE WILL BE BRAND NEW * The cutting guillotine is made of cast steel and is more resistant to fracture, buckling, and abrasion. * Cast steel cutting ram is subjected to a stress-relieving process. * The bolts of the blades on the cutting ram are monitored by the automation system and they are constantly kept tight by the hydraulic tightening system. Fracture and wear of the blades are minimized with this system, and 5 tons of force is applied to each bolt of the blades. * A hydraulic clamping system is used on both the moving and fixed parts of the blades. * Friction surfaces are coated with HARDOX 450 & 500 to prevent wear. * The machine has a fully automatic PLC control and a professional remote controller. * All electric-electronic components used are Schneider and Siemens Brands. * Machine will be under AYMAS Makina San. Ve Tic. A. S. Guarantee for one (1) year or two thousand five hundred (2.500) operation hours, whichever comes first. SEE THE TECHNICAL DESCRIPTION BELOW: Cutting Force: 700 Tons Side Compression Force: 2x120=240 Tons (each wing) Clamp Compression Force: 120 Tons Pusher Ram Force: 120 Tons Nwsdpfxjdd Tp Re Afaef Electric Motor: 180 kW Machine Weight: 70.000 kg Cutting Width: 800 mm Box & Bale Size: 800 mm x 600 mm Box Length: 6.000 mm Box Width Opening: 350 mm Capacity: < 10 - 15 ton/h (Cutting Capacity), 15 - 20 ton/h (Baling Capacity)

Condition: new, Year of construction: 2024, Also, different models are available! IMPORTANT: MACHINE WILL BE BRAND NEW * Piston shafts will be induction-hardened and chrome-plated. * The pressing box will be HARDOX plates. * Pumps and valves used in the hydraulic system will be MARZOCCI brand. * The hydraulic valve control lever unit will be SALAMI or VALVOIL brand. * There will be automatic Oil Cooling/Heating Systems. * There will be an oil temperature control screen on the electric panel and an oil level control on the hydraulic oil tank. * The machine will be manually operated. * All electric-electronic material will be from the SCHNEIDER or SIEMENS brand. * Machine will be under AYMAS Makina San. ve Tic. A. Ş. Guarantee against manufacturing defects for one (1) year or 2.500 working hours whichever comes first. * The machine is CE and EAC certificated. The marking certifies that a product has met European Directives regarding consumer safety, health, or environmental requirements. SEE THE TECHNICAL DESCRIPTION BELOW Bale Size: 600mm x 400mm x ... Container Dimension (Width x Length x Height ): 620mm x 1.300mm x 620mm Njdsdfc Unjpfx Afaowf Capacity:

Condition: new, Year of construction: 2025, Also, different models are available! IMPORTANT: MACHINE WILL BE BRAND NEW SEE THE TECHNICAL DESCRIPTION BELOW 1. Bale Size: 500mm x 500mm x... Nsdogwa T Rjpfx Afaswf 2. Container Dimensions (Width x Length x Height): 2.000mm x 2.500mm x 1.100mm 3. Capacity: 15-20 tons/hour (steel) 4. Cycle Time: 90 seconds ( Idle ) 5. Top Cover Cylinder Thrust: 90 tons 6. Preliminary Compression Cylinder Thrust: 150 tons 7. Main Compression Ram Thrust: 300 tons 8. Maximum Working Pressure: 300 bars 9. Electric Motor: 2 x 75 kW = 150 kW 10. Machine Dimensions (Width x Length x Height): 10.000 mm x 10.000 mm x 4.000 mm 11. Machine Weight: 55.000 kg 12. There will be an ejection door. 13. Repairable and four-edge-usable blades. 14. Container walls will be covered with HARDOX 450 - 500 material. 15. There will be an automatic SKF liquid lubrication system integrated into the compression chamber. 16. There will be an automatic SKF greasing system that will grease the bushings. 17. Piston shafts will be induction-hardened and chrome-plated. 18. Pumps and valves used in the hydraulic system will be by PARKER or EATON VICKERS & KAWASAKI brand. 19. Bypass filter will be added to the hydraulic system. 20. There will be an AKG Hydraulic Oil Cooling System. 21. All electrical parts will be SIEMENS or SCHNEIDER Brand. 22. The machine will be fully automatic with PLC control, PLC brand and model will be SIEMENS. There will be a touch screen SIEMENS HMI Simatic Panel with emergency buttons placed on some important points. 23. There will be blades from 2767 material (hardness 55HRC) at the borders of the top cover and the sides of the scrap chamber. 24. Machine will be under AYMAS Makina San. Ve Tic. A. S. Guarantee for 1 year or 2.500 working hours whichever comes first against manufacturing defects.

Condition: new, Year of construction: 2025, Also, different models are available! IMPORTANT: MACHINE WILL BE BRAND NEW SEE THE TECHNICAL DESCRIPTION BELOW 1. Bale Size: 400mm x 400mm x... 2. Container Dimensions (Width x Length x Height): 1.000mm x 2.000mm x 800mm 3. Capacity: 4 tons/hour (Steel), 5 tons/hour (Copper), 2 tons/hour (Aluminium) 4. Cycle Time: 90 seconds ( Idle ) 5. Top Cover Cylinder Thrust: 90 tons 6. Preliminary Compression Cylinder Thrust: 150 tons 7. Main Compression Ram Thrust: 210 tons 8. Maximum Working Pressure: 300 bars 9. Electric Motor: 37 kW 10. Machine Dimensions (Width x Length x Height): 3.400 mm x 6.800 mm x 3.000 mm 11. Machine Weight: 18.000 kg 12. There will be an ejection door. 13. Repairable and four-edge-usable blades. 14. Container walls will be covered with HARDOX 450 - 500 material. 15. There will be an automatic SKF liquid lubrication system integrated into the compression chamber. 16. There will be an automatic SKF greasing system that will grease the bushings. 17. Piston shafts will be induction-hardened and chrome-plated. 18. Pumps and valves used in the hydraulic system will be by PARKER or EATON VICKERS & KAWASAKI brand. 19. Bypass filter will be added to the hydraulic system. 20. There will be an AKG Hydraulic Oil Cooling System. Nwedpfxjdfc Iys Afaef 21. All electrical parts will be SIEMENS or SCHNEIDER Brand. 22. The machine will be fully automatic with PLC control, PLC brand and model will be SIEMENS. There will be a touch screen SIEMENS HMI Simatic Panel with emergency buttons placed on some important points. 23. There will be blades from 2767 material (hardness 55HRC) at the borders of the top cover and the sides of the scrap chamber. 24. Machine will be under AYMAS Makina San. Ve Tic. A. S. Guarantee for 1 year or 2.500 working hours whichever comes first against manufacturing defects.

Condition: new, Year of construction: 2025, Also, different models are available! IMPORTANT: THE MACHINE WILL BE BRAND NEW The compression chamber walls are covered with HARDOX material for long-term life-cycle and friction resistance. A hydraulic Oil Cooling system is implemented for efficiency in hot climate conditions. Cylinder Rods are induction-hardened and chrome-plated. Pumps and valves of hydraulic systems are from worldwide reputable brands such as PARKER, and BOSCH-REXROTH. The machine is fully automatic by PLC control. It is easy to use with the help of the touch screen. All electrical and electronic parts are by SCHNEIDER and SIEMENS Brands. The machine is CE-certified. The marking certifies that a product has met European Directives regarding consumer safety, health, or environmental requirements. Machine will be under Aymas Makina San. Ve Tic. A. Ş. Guarantee against manufacturing defects for one (1) year or two thousand five hundred (2.500) working hours. SEE THE TECHNICAL DESCRIPTION BELOW Njdpfx Afjdfcqajaowf Bale Size 400mm x 400mm x... Bale Weight 120-180 kg (Steel), 50-80 kg (Aluminium),150-200 kg (Copper) Press Box Dimensions (Width x Length x Height): 1.000mm x 2.700mm x 900mm Loading Bunker Dimensions (Width x Length x Height): 1.650mm x 2.300mm x 800mm Feeding Opening: 1.000mm x 1.600mm Capacity*

Condition: new, Year of construction: 2025, Also, different models are available! Njdpfx Asd Iya Nofaowf IMPORTANT: THE MACHINE WILL BE BRAND NEW The compression chamber walls are covered with HARDOX material for long-term life-cycle and friction resistance. A hydraulic Oil Cooling system is implemented for efficiency in hot climate conditions. Cylinder Rods are induction-hardened and chrome-plated. Pumps and valves of hydraulic systems are from worldwide reputable brands such as PARKER, and BOSCH-REXROTH. The machine is fully automatic by PLC control. It is easy to use with the help of the touch screen. All electrical and electronic parts are by SCHNEIDER and SIEMENS Brands. The machine is CE-certified. The marking certifies that a product has met European Directives regarding consumer safety, health, or environmental requirements. Machine will be under AYMAS Makina San. Ve Tic. A. Ş. Guarantee against manufacturing defects for one (1) year or two thousand five hundred (2.500) working hours. SEE THE TECHNICAL DESCRIPTION BELOW Bale Size 400mm x 400mm x... Bale Weight 100-180 kg (Steel), 40-100 kg (Aluminium),120-180 kg (Copper) Press Box Dimensions (Width x Length x Height): 1.000mm x 2.600mm x 900mm Loading Bunker Dimensions (Width x Length x Height): 1.500mm x 2.200mm x 650mm Feeding Opening: 1.000mm x 1.600mm Capacity*

Condition: good (used), Year of construction: 2001, functionality: fully functional, KAMPWERTH SHD 1600 horizontal baler, incl. 3 interchangeable containers 48000x2800x3000 Paper baler // Waste baler // Refuse baler Baler, 1 unit • Type: Kampwerth SHD 1600 • Year of manufacture: 2001 • Unladen weight: 3,500 kg • 15 kW • Dimensions: 5000x2300x3700 mm (disassembled for transport) Container box for baler, 3 units • Year of manufacture: 2001 Nodpfx Aexm Skrjfaswf • Volume: 28 m³ • Unladen weight: 3,100 kg • Filling weight: 12,000 kg • Dimensions: 7000x2400 mm Location: Bielefeld

Condition: ready for operation (used), Year of construction: 2008, Brand: HSM Model: V-Press 1160 plus Year of manufacture: 2008 Pressing force: 532 kN Voltage: 400 V Max. bale weight: up to 550 kg (depending on material) Bale dimensions: 120 x 110 x 120 cm Machine weight: 2,403 kg Machine dimensions: 180 x 157 x 298.5 cm Filling opening: 119.5 cm × 65 cm Condition: very good! Nodpfxeyyk Tze Afaowf Video of the machine in operation available upon request.

Condition: new, Year of construction: 2022, functionality: fully functional, machine/vehicle number: Machinenummer 230067.020, pressing force: 60 t, power: 45 kW (61.18 HP), operating pressure: 250 bar, Bollegraaf Recycling Solutions, the original manufacturer of this mobile Bollegraaf baler, hereby offers the following machine(s) Nwodpfx Afjh I T Ibjasf FOR RENT ONLY: Year of construction: 2022 Weight excl trailer: 22.000 kg Mobile Baler Volume capacity m3/hr max. 365 334 321 301 Volume weight kg/m3 max. 15 30 50 80 Weight capacity T/hr max. 5.5 10 16 24 Bale weight 400 – 800 kg, depending on S.G. of material and bale length Bale length - adjustable Bale height - 720 mm Bale width - 1100 m Filling opening - 1100 mm x 1320 mm Max. size supply - 1500 mm x 1200 mm Pressure force ram - max 60 tonf. Pressure force pre-press flap - max 25 tonnes Cycle time - 18 seconds Motor - 45 kW Motor Twistomat - 2.2 kW Motor counter pressure pump - 1.1 kW