Used Baler for sale (236)

Condition: new, Year of construction: 2023, machine/vehicle number: 7YXXX, VIS G is the ideal and the most efficent solution for serap processing like stampings, trimmings, wires mostly recommended for the automotive industry, metal recyclers and non-ferrous metal remelting industry. Hnsdpfomqi Akex Ak Djn

Condition: reconditioned (used), Year of construction: 2007, operating hours: 22,605 h, functionality: fully functional, pressing force: 100 t, filling opening width: 1,100 mm, filling opening length: 1,600 mm, bale width: 1,100 mm, bale height: 1,100 mm, bale weight: 900 kg, oil tank capacity: 1,300 l, power: 75 kW (101.97 HP), year of last overhaul: 2025, For sale is a overhauled Bollegraaf baler, with 100 tonnes pressing force, large bale format 1100 x 1100 mm, 75 kW drive power and 10-fold cross binding system Technical data baler: Manufacturer Bollegraaf Typ HBC 110 K / 75 kW Year of construction 2007 Press power main press 100 tons Press power of pre-press 50 tons Operating hours 22,605 hours Feed channel 1,600 x 1,100 mm Capacity per cycle time 3,15 m³ Theoretic cycle time 19 sec. Bale size 1,100 x 1,100 mm Driving motor 75 kW Connected load 126 kW Full load current 238 A Tying system 5-fold vertical, 5-fold horizontal, fully automated Throughput rate at a bulk weight of 30 kg/cbm approx.16 tons/h bulk weight of 50 kg/cbm approx. 25 tons/h bulk weight of 100 kg/cbm approx. 47 tons/h Bale weight up to 1400 kg, depends on material and bale lenght Volume oil tank approx. 1,300 l SPS controller Telemecanique TSX Micro Operating panel Schneider MAGELIS Touch Baler dimensions built up with hopper 11,750 x 5,000 x 7,105 mm (l x w x h) Hsdpfjzdn H Rex Ak Donn Transport dimensions only baler 11.750 x 2.500 x 3.450 mm (l x w x h) Machine weight baler approx. 36 tons Comments: The press was partially overhauled and serviced in our workshop and tested and stored after completion of the work. The machine is available at short notice and can be inspected in our warehouse by appointment. The following overhaul work was carried out: Rust removal and partial painting of the press. Remaining hydraulic oil tank drained, oil filter and air filter replaced. New hydraulic oil topped up. All hydraulic hoses replaced. Main hydraulic cylinder, two cylinders of the prepress flap and the cylinder of the press channel dismantled, disassembled, checked, cylinder tubes honed, all seal sets replaced and a final pressure test carried out. Disassembly of the prepress flap with bearings and bearing blocks. 1st and 3rd circular arc segmet cut out and a new one welded in again. Both bearings of the shaft of the prepress flap replaced. Upper material deflector on the frame of the prepress flap replaced. Press ram dismantled, checked and both front rollers replaced. Material deflectors and wear profiles on the sides and base of the press ram cut off and new ones welded in. Horizontal and vertical needle and tying unit dismantled, disassembled, checked, plastic sliding plates, bearings of the drill shafts and wire deflection rollers with bearings in the needle heads replaced. Both bronze slide rails on the left and right in the frame cover to the press ram replaced. Both wire deflection units on the left and right, with bale retaining clamps, completely renewed. Wire insertion unit including hydraulic cylinder under the needle feedthroughs completely renewed. Wire entry marks in the floor and side walls of the bale chamber welded shut and smoothed. General maintenance and service work carried out in accordance with the manufacturer's specifications. Press tested in manual and automatic mode, accepted and stored after completion of overhaul work. We accept no liability for the technical specifications or any errors.

Condition: reconditioned (used), Year of construction: 2015, operating hours: 30,143 h, functionality: fully functional, pressing force: 60 t, filling opening width: 1,100 mm, filling opening length: 1,500 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 570 kg, overall weight: 20,000 kg, oil tank capacity: 600 l, power: 37 kW (50.31 HP), year of last overhaul: 2025, volume flow: 800 m³/h, Technical data baler: Manufacturer Presona AB, Sweden Type LP 60 VH1 Year of construction 2015 Total operating hours, 30,143 hours, as of July 2025 Effective pump running time onl 6,527 hours, as of July 2025 Number of pressed bales 115,193 bales, as of July 2025 Press force pre press 25 t Main press force 60 tonnes Specific pressing force 73N/cm² Dimensions of feed chute 1,500 x 1,100 mm Filling volume / pressing cycle 2.7 m³ Theoretical throughput capacity 800 m³/hour Throughput capacity under operating conditions 350 m³/hour Bale dimensions 1,100 x 750 mm Drive power 37 kW Tying 5-fold vertical, fully automatic Throughput capacity with a Bulk weight of 50 kg/cbm 11 to 14 tonnes/hour Bale weights 420 to 570 kg, depending on material Hydraulic oil tank volume 600 litres Baler dimensions assembled with hopper 10,100 x 3,750 x 4,310 mm (l x w x h) Transport dimensions excluding press 10,100 x 2,400 x 3,000 mm (l x w x h) Machine weight press approx. 20 tonnes Condition of the press: The press was partially overhauled in our workshop and then tested in manual and automatic mode. The following overhaul work was carried out: Machine cleaned, partially derusted and partially repainted Hydraulic oil tank emptied and cleaned Oil filter and air filter replaced, new hydraulic oil filled Press ram dismantled and cleaned All four rollers removed from the press ram and replaced Grease cartridges of the automatic roller lubrication system replaced Slide rails cut out from the press floor in the press room Underbody reinforced with welded sheets New HARDOX slide rails welded in Wire station with deflection rollers for the lower wire cleaned and made operational Slide rails cut out from the floor in the press channel New HARDOX slide rails welded in Hnsdpfxjzdny Rj Ak Den Both side walls of the press channel dismantled, derusted Worn side wall plates cut out Complete side walls covered with new wear plates and welded Main hydraulic cylinder dismantled and disassembled for inspection Piston rod replaced, cylinder tube honed Complete seal set replaced, pressure test carried out Vertical needle system for binding dismantled, cleaned, wire deflection rollers made functional and serviced Chain cleaned, greased, chain tension readjusted Drillomat cleaned, wire knife, drill shafts and drill fingers checked, retightened with torque and serviced Machine checked, general maintenance work carried out and press tested in manual and automatic mode Comments: The press is sold without a conveyor belt and without wire stations. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: reconditioned (used), Year of construction: 2012, operating hours: 25,895 h, functionality: fully functional, pressing force: 78 t, filling opening width: 1,100 mm, filling opening length: 1,500 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 600 kg, overall weight: 24,000 kg, oil tank capacity: 1,000 l, year of last overhaul: 2025, volume flow: 410 m³/h, Technical data baler: Manufacturer Presona AB Typ LP 80 VHK 1 Year of construction 2012 Total machine operating hours 25,895 hours, as of July 2025 Pump operating hours, effective 14,135 hours, as of July 2025 Number of bales pressed 235,597 pieces, as of July 2025 Press power main press 78,5 tons Specific press capacity 95 N/cm² Press power of pre-press 28 tons Volume of pressing chamber 2,7 m³ Feed channel1,500 x 1,100 mm Theoretic throughput rate 930 m³/h Throughput rate under operating conditions 410 m³/h Bale size 750 x 1,100 mm Driving motor 55 kW Tying system 5 fold vertical, 3-fold horizontal, full automatic Throughput rate with a bulk density of 30 kg/m³ approx. 9 to 12 tonnes/hour, depending on material 50 kg/m³ approx. 14 to 17 tonnes/hour, depending on material 100 kg/m³ approx. 16 to 25 tonnes/hour, depending on material Throughput capacity with MSW (Municipal Solid Waste) approx. 20 to 27 tonnes/hour, depending on material Bale weight 450 up to 600 kg, depends on material and bale length Volume hydraulic oil tank 1,000 l Hsdszdnxgopfx Ak Djnn Baler dimensions built up with hopper 10,985 x 3,750 x 4,310 mm (l x w x h) Transport dimensions only baler 10,985 x 2,300 x 2,900 mm (L x w x h) Machine weight baler approx. 24 tons Condition of the press: The machine was partially overhauled and serviced in our workshop and, once the work was complete, tested in manual and automatic mode during operation. The following overhaul work was carried out: Machine cleaned, partially derusted and partially repainted Hydraulic oil tank emptied and cleaned Oil filter and air filter replaced, new hydraulic oil filled Press ram dismantled and cleaned All four rollers removed from the press ram and replaced Wire station with deflection rollers for the lower wire cleaned and made operational Side guides removed from the press ram, smoothed, mounted and readjusted Main hydraulic cylinder dismantled and disassembled for inspection Piston rod replaced, cylinder tube honed Complete seal set replaced, pressure test carried out Vertical and horizontal needle system for binding dismantled, cleaned, wire deflection rollers made functional and serviced Chain cleaned, greased, chain tension readjusted Drillomat cleaned, wire knife, drill shafts and drill fingers checked, retightened with torque and serviced Door contact switch checked and partially replaced. Emergency stop switch checked. Complete electrical wiring checked and partially replaced. Bearings of the wire guide rollers under the press replaced. New safety grilles for vertical and horizontal binding manufactured and installed. Machine checked, general maintenance work carried out and press tested in manual and automatic mode Scope of delivery: Only the baler will be sold. Comments: The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: as good as new (ex-display), Year of construction: 2026, The BTS-MF450HD special waste baler is the ideal baler for compacting difficult materials such as PET bottles, food cans and metal containers, big bags, plastic canisters and plastic packaging, but also scrap tyres and car bumpers can be reduced to a minimum of volume with the baler. The special baling press impresses with its ease of use, safe operation and its spacious filling chamber, it is ideal for medium to large amounts of material. By baling these valuable and recyclable materials you achieve a volume reduction of up to 90%, a significant saving on your disposal costs and you properly return the material back into the recycling cycle. Hnodpfxevug Dys Ak Den Pressing force: 30 Ton Bale weight: up to 450 kg (material depending) Bale size: 1000 H (var.) x 1200 W x 800 D mm Machine size: 3343 H x 1781 W x 1196 D mm Machine weight: 1600 kg Transport height: 2300 mm Loading aperture: 1200 W x 680 H mm Cycle times: 40 seconds Motor: 5.5 kW 16 Amp Power supply: 380 - 400 V (3 phase) Noise level: 68 dB Extra-long dual cylinders for even and early compaction of the material User-friendly lever control Bale kicker for easy eject the bales Extra retainer for reducing the material spring back Reel holder for 4 rolls of strapping A quality product “Made in Europe” Suitable for compacting PET bottles Food cans and sheet metal containers Canisters and plastic containers / packaging Scrap tyres and car bumpers Big bags Cardboard and plastic film / foils Other difficult valuable materials Optional extras Machine colour RAL PLC auto compaction cycles with bale full light and E-stop with locking key Sliding top door Strapping rolls / bale wire Motor 11 kW 32 Amp Demo-Video shows BTS-MF550HD Special Waste Baler. Can Baler, Can Waste Baler, PET Baler, PET Compactor, Tyre Baler, Tire Baler, Scrap Tyre Baler, Scrap Tire Baler, Tyre Compactor, Tire Compactor, Can Baler, Waste Baler, Waste Compactor, Cardboard Baler, Film Baler, Foil Baler, Packaging Plastic Film Foil, Bailer, Baling Press, Garbage Press, Trash Compactor, Baling Compactor, Paper Press, Waste Paper Press, Cardboard Press, Cardboard Compactor, Foil Press, Paper Baling Press, Waste Baler, Residual Waste Compactor

Condition: ready for operation (used), Year of construction: 2009, Brand: HSM Model: V-Press 1160 plus Year of manufacture: 2009 Pressing force: 532 kN Voltage: 400 V Max. bale weight: up to 550 kg (depending on material) Bale dimensions: 120 x 110 x 120 cm Machine weight: 2,403 kg Machine dimensions: 180 x 157 x 298.5 cm Filling opening: 119.5 x 65 cm Condition: very good! Video of machine in operation available on request. Hnjdpfx Akszdpctj Dsn

Condition: ready for operation (used), Year of construction: 2009, Well-maintained PRESTO HPK 50 BSK automatic horizontal baler in fully operational condition. The machine has been in continuous industrial use and has been regularly serviced and professionally maintained throughout its lifetime. It was recently dismantled from operation due to plant modifications and is ready for transport and immediate recommissioning. Suitable for baling: Cardboard (OCC) Paper Mixed recyclables Plastic films PET bottles Packaging waste The HPK 50 BSK is a compact and reliable industrial baler designed for medium to high throughput operations. Its large feed opening allows efficient loading by conveyor, wheel loader or excavator. The fully automatic wire tying system ensures consistent bale quality and low operating costs. The PRESTO HPK series is well known throughout Europe for durability, simple maintenance and reliable operation. Pressing force: 50 t Motor power: 22 kW Power requirement: 400 V / 80 A Feed opening: 1,250 x 1,050 mm Bale dimensions: 1,100 x 700 mm Bale weight: up to approx. 500 kg depending on material Hodpszcdrnsfx Ak Dsnn Cycle time: approx. 22 sec Throughput: up to 5–10 t/h depending on material density Fully automatic 4-wire tying Machine dimensions: approx. 6,820 x 1,950 x 2,160 mm Machine weight: approx. 8.75 t

Condition: good (used), Year of construction: 2014, Large waste compactor / cardboard press, Höma, – used: Hjdpfxezbyf Io Ak Donn Price at location: only €18,950 (net) for self-dismantling! Manufacturer: Höma Type: PB4000 Year of manufacture: 2014 Machine number: 140409 Weight: 1,200 kg Pressing force: not specified, but we estimate 40 tons. The press has a second discharge chute. Price includes a small crane with trolley. 30 kW Condition: good Available: from Q4/2026 Location: Hamburg For an additional charge, a conveyor system for empty cardboard boxes, over 100 m long, is available! Photos at the end of the advertisement!

Condition: reconditioned (used), Year of construction: 2002, operating hours: 44,590 h, functionality: fully functional, pressing force: 200 t, filling opening width: 1,020 mm, filling opening length: 2,000 mm, bale width: 1,100 mm, bale height: 1,100 mm, bale weight: 1,000 kg, oil tank capacity: 3,100 l, power: 150 kW (203.94 HP), year of last overhaul: 2025, volume flow: 795 m³/h, Technical data baler: Manufacturer MACPRESSE EUROPA S.R.L. Typ 112 Year of construction 2002, partially refurbished in December 2025 Operating hours 44,590 hours, stand December 2025 Press power main press 200 tons Specific press capacity 16,5 kg/cm² Feed channel 2,000 x 1,020 mm Filling volume 2,65 cm³ Theoretic throughput rate 795 m³/h Bale size 1,100 x 1,100 mm, length variable Driving motor 2 x 75 kW Tying system 5-fold horizontal, full automatic Throughput rate at MSW approx. 48 up to 54 tons/h, depends on material Volume hydraulic oil tank 3,100 l Machine weight baler approx. 50,8 tons Scope of delifery: 1 piece baler MACPRESSE, type 111A 1 operating manual with CE declaration, electrical and hydraulic circuit diagram Comments: The machine was serviced and partially overhauled in our workshop. The following work was carried out and parts replaced: • Hydraulic oil tank emptied and cleaned • Oil and air filters replaced • New hydraulic oil filled • All hydraulic hoses replaced • Press ram dismantled, broken down into individual parts, mechanics made operational • Front two main rollers replaced • Knives on the press ram replaced • Main hydraulic cylinder dismantled, disassembled, cylinder tube and piston rod checked, complete seal set replaced • Counter knife in the frame replaced • Knife gap adjusted to approx. 3 mm • Upper steel guide rails in the frame on the left and right replaced. • Worn press base cut out, base plate replaced with wear-resistant HARDOX steel. • Binding and twisting unit dismantled, broken down into individual parts, mechanics made functional, all twisting shafts and ball bearings replaced. • All wire rollers in the needle heads replaced • Wire knives cleaned and readjusted, chains greased and tensioned • All wire deflection rollers made operational • All door contact switches replaced • Wirbulator device dismantled, disassembled and made operational • General maintenance work carried out Hodpezbxwisfx Ak Denn Finally, the press was subjected to a machine test in manual and automatic mode, see video for the machine function test. The documentation (BA, CE, electrical/hydraulic circuit diagram) is complete. Viewing is possible by appointment. We accept no liability for the technical specifications or any errors.

Condition: ready for operation (used), Year of construction: 1994, Brand: HSM Model: 155 VL Year of construction: 1994 Hjdezc Hhxspfx Ak Djnn Pressing force: 157 kN Voltage: 400 Max. bale weight: 250 kg Bale dimensions: 110 x 70 x 95 cm Machine weight: 950 kg Machine dimensions: 144 x 100 x 234 cm Feed opening dimensions: 110 x 59 cm

Condition: ready for operation (used), Technical specifications of Dixi 60 AUTOMAT baler Filling opening (W x H): 1550 x 1000 mm Drive power: 31.5 kW Pressing force: 60 t Bale weight (depending on material): 350–600 kg Bale dimensions (W x H x D, adjustable): 1100 x 800 x 300–1600 mm Hsdjv Amw Nspfx Ak Dsnn Pressing/cycle time: 13/24 s Machine weight: 7000 kg

Condition: like new (used), Year of construction: 2014, functionality: fully functional, Cameras for Premier Tech – suitable for high-speed compression balers. Used very little, practically new. Hodpfxozckp He Ak Donn Can be used for bags measuring 465x365x1320 mm.

Condition: excellent (used), Year of construction: 1996, pressing force: 30 t, input voltage: 380 V, bale weight: 600 kg, type of input current: AC, overall weight: 3,000 kg, Manufacture: Philadelphia Tramrail Model: HT30036 Vintage: 1996 400V/45A, 3 phases, 15kW 180 bar system pressure 206 bar maximum system pressure Made of heavy-duty structural steel Average cycle time of 53 seconds Dimensions: 1980 x 1050 x 3860mm Hsdom Amk Njpfx Ak Donn Advance height: 1400mm Baling chamber: 1600 x 760

Condition: used, functionality: limited functionality, Year of construction: 2013, Gallignani baling press Hnjdozb I Nhepfx Ak Djn Subject to prior sale – all information is provided without warranty. We cannot guarantee the accuracy or completeness of the information provided here. Any warranty and/or liability is excluded. Deviations from the description above cannot be ruled out. We would like to point out that the subject of the purchase agreement to be concluded will be exclusively the motor vehicle in its actual condition.

Condition: ready for operation (used), Year of construction: 2008, Brand: HSM Model: V-Press 1160 plus Year of manufacture: 2008 Pressing force: 532 kN Voltage: 400 Max. bale weight: up to 550 kg (depending on the material) Bale dimensions: 120 x 110 x 120 cm Machine weight: 2403 kg Machine dimensions: 180 x 157 x 298.5 cm Feed opening dimensions: 119.5 cm × 65 cm Condition: very good! Hjdpfx Ajzaqymek Dsnn Video of the machine in operation available upon request. Transportation is also possible.

Condition: excellent (used), Year of construction: 2018, Baler, Bramidan B20 - second-hand - : Price ex location: 7.750.-€ (net) Manufacturer: Bramidan Type: Vertical raw material balers B20 Year of construction: 2018 Bale weight Cardboard (kg) 200-250 Plastic film (kg) 250-300 Pressing force 20 t Bale size WxDxH (mm) 1200 x 800 x 800 Filling opening WxH (mm) 1200 x 480 Power supply 3x400V 50Hz 16A Motor (kW) 4.0 Cycle time average (s) 36 / 21 Dimensions WxDxH (mm) 1775 x 1030 x 2790 Transport height: 2.58m Weight (kg) 1250 Stroke (mm) 750 Number of tie-downs 4 Type of strapping Strap Finished bale light Yes Bale ejection Automatic Hjdpfx Akjrl I Ivo Donn The classic among raw material balers The B20 is versatile and is used everywhere. The recyclable materials must be "dry & soft". Particularly suitable for raw materials such as cardboard, paper, cardboard packaging (PPK) and film. Stackable bales, up to 900 kg per pallet The bales are stacked 2 or 3 high on one; enormous space saving. Simple bale strapping Automatic bale ejection Short cycle time thanks to high speed Strap rollers mounted on the front allow installation directly on the wall Pallet-sized bales that can be stored outdoors under cover 3xx230x-440 4kW Amps: 25/16 dB 62-64 Condition: good - very good Available: immediately Location: 09116 Chemnitz

Condition: used, Waste compactor, baler, waste baler, chamber baler, Orwak Compactor 3110, used machine Manufacturer: ORWAK (Sävsjö, Sweden) Type: Compactor 3110 Serial No: 105441 Product No: 4903110-00 Overall dimension: 865 x 680 x 2050 mm -press force: 4t -production date: 2011-11 Hnjdpjy S Ui Dsfx Ak Don -voltage: 230 V -frequency: 50 Hz -power: 1.1 kW -current: 8.9 A -weight: 340 kg

Condition: ready for operation (used), Baler Hsm 155 VL Bale dimensions L x W x H: 1100 x 700 x 700 - 950 mm Bale weight: 2000 - 250 kg (Cardboard) Technical data: L x W x H: 1470 x 940 x 2259 / 2439 mm Weight: 950 kg Pressure force 16 tons Power supply: 400 V (three phases) Motor power: 4 kW Bale ejector Hsm 155.1 VL baler pressure force 18 tons Price of Hsm 155.1 VL baler - 2600eur Hsm 155.2 vl baler pressure force 16 tons Price of hsm 155.2 vl baler - 2800eur Hodera Nrmopfx Ak Dsnn

Condition: reconditioned (used), Year of construction: 1996, functionality: fully functional, pressing force: 170 t, filling opening width: 1,020 mm, filling opening length: 1,800 mm, bale width: 1,100 mm, bale height: 1,100 mm, bale weight: 900 kg, overall weight: 40,000 kg, oil tank capacity: 3,000 l, year of last overhaul: 2025, volume flow: 750 m³/h, For sale is a used baling press system consisting of a chain belt conveyor for underfloor operation, with a feed hopper, a hydraulic pre-compactor with ruffler, a MACPRESSE 111A baling press, two complete wire drawing frames with 5 wire reel stands each, without wire. Technical data baler: Manufacturer MACPRESSE EUROPA S.R.L. Typ 111A Year of construction 1996, refurbished in 10/2024 Press power main press 170 tons Specific press capacity 14 kg/cm² Feed channel 1,800 x 1,020 mm Filling volume 2,5 cm³ Theoretic throughput rate 750 m³/h Bale size 1,100 x 1,100 mm, length variable Driving motor 2 x 55 kW Tying system 5-fold horizontal, full automatic Throughput rate at a approx. 30 up to 35 tons/h, depends on material Volume hydraulic oil tank 3,000 l Transport dimensions of press with new machine feets 113,700 x 2,300 x 2,900 mm (l x w x h) Machine weight baler approx. 40 tons Comments: The baler was partially overhauled in our workshop and tested after completion of the work, please look at our functional video. The system was previously used to bale paper and cardboard from municipal collections. The contract was awarded elsewhere after the end of the contract period, so the complete system is for sale. The overhaul work carried out and the spare parts replaced can be found in the detailed photo documentation and in our quotation. The documentation (Manual, CE, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors. Technical data conveyor belt: Manufacturer Wagensfeld B.V. Type chain belt conveyor 1700 mm Year of construction 2017 Drive power 7.5 kW Belt speed 14 m/minute Length of infeed conveyor 6,900 mm Length of ascending belt 12,885 mm Length of gooseneck 1,747 mm Overall length 21,271 mm Pitch 32° Effective width 1,644 mm Height of drive shaft above ground 5,777 mm Wall height of feed conveyor 500 mm Wall height of ascending conveyor 880 mm Steel flights height 40 mm Distance between flights 1200 mm Transport dimensions conveyor disassembled 15,005 x 2,503 x 2,435 mm (l x w x h) Hnodpjy S Rqwjfx Ak Djn Pit dimensions 11,500 x 2,700 x 1,015 mm (l x w x d) Remarks: The chain belt conveyor, built in 2017, was later made to fit the baler during the last installation of the baler in the Netherlands and is newly installed. The conveyor belt is in good, operational condition and has therefore not been overhauled. An installation drawing with the pit dimensions is available. Scope of delifery: 1 chain belt conveyor, Wagensveld B.V. 1 piece feed hopper with pre-compressor flaps 1 piece wirbulator 1 baler MACPRESSE, type 111A 2 wire drawing frames with wire reel stands, without wire 1 operating manual with CE declaration, electrical and hydraulic circuit diagram

Condition: used, Year of construction: 1995, functionality: limited functionality, cutting force: 800 t, empty load weight: 190,000 kg, type of input current: three-phase, Arnold HS850 Scrap & Metal Presse Die Maschine befindet sich derzeit in transportbereitem Zustand. master cylinder cylinder force: 850 t press: 0.08m/s hold-down cylinder cylinder force: 100t / per cylinder feed cylinder: cylinder force:100t cover cylinder: cylinder force:100t main dimensions total length:16175mm total width:5200 total height: 6420 mm Dimensions: Passage width at the scissor stand: 800mm passage height at the scissor stand: 800mm total height: 6000mm weights: scissor stand with cutter bar: 60 ton feed device approx: 85 ton total weight: about 170 tons required amount of oil: 5200 liters Hnedpfxoh T Dcto Ak Don connection value of the machine: 220kw If you need more information. We are here to help! Please contact us using the contact form or give us a call Your ad has been automatically translated. Translation errors are possible.

Condition: used, Year of construction: 2005, Chamber press - baling press Austropressen APV 300, used 🧰 Product features • Manufacturer: Austropressen • Model: APV 300 • Condition: Used item, see photos • Color: turquoise • Year of manufacture: 2005 • Dimensions: approx. 1620 x 1260 x 2920 mm Hnsdpfxsxvy N Uj Ak Djn • Own weight: 1650 kg • Pressing force: 300 kN • Cycle time: 45 seconds • Power: 5.5 kW • Voltage: 400 V (12.5 A) • Bale weight: 300 - 400 kg 💰 Price: €7,200 net excl. VAT • Quantity discount: on request • Shipping: Europe-wide on request • Delivery time: Immediately available • Inspection and collection: possible at any time by appointment Constantly over 5,000 linear meters of pallet racking from various manufacturers in stock (Technical data, details, and prices subject to change and error, as well as prior sale! See our GTC, all prices excl. VAT ex stock.)

Condition: used, Year of construction: 2019, Chamber Press - Baling Press - Raw Material Press Bramidan X30 AD, used 🧰 Product Features • Manufacturer: Bramidan • Model: X30 AD • Condition: Used, see photos • Color: Orange • Year of manufacture: 2019 • Dimensions: approx. 1760 x 1255 x 2295 mm • Net weight: 1650 kg • Press force: 300 kN • Cycle time: 25 seconds • Power: 4 kW • Voltage: 3 x 230 - 440 V / 50/60 Hz • Noise level: 59 - 60 dB • Bale weight: Plastic up to 425 kg, cardboard up to 350 kg 💰 Price € 8,900 net excl. VAT • Quantity discount: on request • Shipping costs: Europe-wide on request • Delivery time: Immediately available • Inspection and collection: possible at any time by prior arrangement Hnodpsxvyn Djfx Ak Don Constantly over 5,000 linear meters of pallet racking from various manufacturers in stock (Subject to changes and errors in technical data, information and prices as well as prior sale! See our terms and conditions; all prices excl. VAT ex stock.)

Condition: used, High-performance baler MACFAB - BEMA type 650A Hydraulic press for packaging waste, recyclable renewable raw materials, secondary raw materials Manufacturer no. MF J0162 Year of manufacture 2021 Pressing force 50 tons. Press plate stroke approx. 1000 mm Hnjdpfsvq Rtkox Ak Djn Cycle time per stroke approx. 40 sec. Pressing chamber floor area 1500 x 1100 mm Pressing chamber height 1650 mm Filling opening 1500 x 870 mm Filling height approx. 1250 mm Bale format 1500 x 1100 mm Bale height max. 1100 mm Hydraulic operating pressure 200 bar Motor power 5.5 kW Mains connection 400 volts, 50 Hz, 12 amps. - with two hydraulic cylinders - Door locking via threaded spindle with handwheel - Pressing operation only with the pressing chamber door closed - 2-hand operation for hydraulic tipping of the finished pressed bale - Free space for manual strapping - Standard industrial bales of 1500 x 1100 x 1100 mm are produced - the highly compressed bale is automatically tipped onto a pallet - only 62 operating hours Space requirement L x W x H 2120 x 1350 x 3220 mm Height for transport with lowered hydraulic cylinders approx. 260 cm Weight 1.8 ton. The machine is in very good condition, as good as new. The press has a new price of EUR 22,200 net at BEMA The BEMA company also buys the packaging waste that you press into bales with this press.

Condition: ready for operation (used), Year of construction: 2013, Brand: HSM Type: V-Press 1160 plus Year of manufacture: 2013 Pressing force: 532 kN Voltage: 400 Hnjdpjy Uimvjfx Ak Den Max. bale weight: up to 550 kg (depending on the material) Bale dimensions: 120 x 110 x 120 cm Machine weight: 2403 kg Machine dimensions: 180 x 157 x 298.5 cm Feeding opening dimensions: 119.5 cm × 65 cm Condition: very good! Video of the machine in operation available upon request.

Condition: used, functionality: fully functional, Main Technical Specifications Machine Model: COMDEC LV 50-40 PFT horizontal baling press Pressing force: 50 tons Horizontal hydraulic baler for cardboard, paper and industrial waste Electrical data Power supply: 380 V / 3 phase / 90 A Hydraulic motors: 2 × 22 kW hydraulic pump motors Conveyor pump motor Hnedpfx Akoy Uddij Don Hydraulic system Hydraulic main cylinder: 180 / 150 × 2000 mm Hydraulic pressure control system with oil cooling and filtration Oil tank with pressure and return filters Machine dimensions Total machine length: approx. 8,394 mm Width: approx. 1,920 mm Height: approx. 3,104 mm Functional equipment Automatic wire tying system Bale length control system Hydraulic wire twisting unit Automatic bale ejection system Conveyor control cabinet and electrical automation system Noise level Working noise level below 70 dBA