Used Faymonville Multimax Satteltieflader (1+2) - Nachlaufgelenkt for sale (105,916)

Condition: new, maximum load weight: 36,410 kg, overall weight: 48,000 kg, axle configuration: 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete vehicle inventory with immediately and short-term available vehicles on our website. Extract from the equipment. Full equipment details available on request. GOOSENECK: * Gooseneck in SNT design for optimized loading platform length, length approx. 3,700 mm, rear with taper approx. 1,000 mm x 10° * For tractor units: 4 x 2, 6 x 2, and 6 x 4 * Steel front wall, removable, approx. 400 mm high * ASPÖCK-UNIBOX * 3 kW electro-hydraulic power unit for hydraulic functions, excluding hydraulic winches * Approx. 40 mm thick hardwood decking above the gooseneck * 2-inch kingpin * Gooseneck guide plate for the fifth-wheel plate, approx. 500 mm wide * Bracket at the rear of the gooseneck for ALU loading ramps * Round NATO socket on the front connection panel (Maeler & Kaege VG 96 917) Rsdpfxoy Auh Ie Ag Usu * 4 wheel chocks with holders in front of the front wall * 1 pair of stake pockets recessed on the gooseneck for plug-in stakes approx. 100 x 50 mm (located on the inside of the chassis rail) EQUIPMENT: * Loading platform length approx. 8,800 mm, extendable version approx. 4,100 mm, with rear taper approx. 500 mm x 10° * A recess in the loading platform, extending into the tapered section to accommodate the excavator dipper stick, approx. 2,490 x 750 x 210/290 mm (L x W x H) * Pneumatic locking with conical locking bolts and reinforced locking positions, supply lines are protected inside the extendable beams and automatically adapt to the selected loading platform length * TPMS tire pressure monitoring system in accordance with ECE R 141 * BPW axles and suspension, 1st and 2nd axles rigid, 3rd axle steered * 3rd axle with electro-magnetic reverse lock, activated via reverse gear and manually * Technical axle load: each 12,000 kg with air suspension and raise/lower valve * 235/75 R 17.5 3PMSF twin tires. Manufacturer at our discretion * Mechanical landing legs with 2-speed gearbox and crank. JOST Module B – static test load = approx. 50,000 kg * Throughout the loading platform and between the axles, interrupted approx. 50 mm thick hardwood decking (increases coefficient of friction) * 1 intermediate table, approx. 300 mm wide, for the telescopic tube with large cross-section. Intermediate table with offset loading platform and extendable mounting rails for aluminum bridging elements * Platform locking with conically welded locking profiles every approx. 250 mm. Includes pre-tensioning plate * 1 pair of lashing rings on the front cross member (LC 10,000 daN) * 9 pairs of recessed lashing rings in the outer frame of the loading area, foldable outwards (LC 10,000 daN) * 1 pair of fixed wheel recesses in front of the axles, open up to the gooseneck cross member, approx. 700 x 410 mm (W x D) * Wheel recesses with 15 x 15 mm square climbing strips and widenings at the bottom (in case vehicle is equipped with extendable widenings) * 1 pair of fixed wheel recesses, approx. 1,480 x 700 x 410 mm (L x W x D), in the platform between 1st and 2nd axle * Wheel recesses with 15 x 15 mm square climbing strips and widenings at the bottom * Aluminum covers for the wheel recesses in front of the axles and between the 1st and 2nd axle, which can also be used as widening planks (if vehicle is equipped with extendable widenings) * Lockable aluminum elements installed on the extension tubes of the widenings * 1 pair of mechanical rear supports * 1st axle with traction aid * Sandblasting painted...

Condition: new, maximum load weight: 51,780 kg, overall weight: 65,000 kg, axle configuration: > 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete vehicle inventory, including immediately and short-term available units, on our website. Excerpt of Features. Full equipment list available upon request. GOOSENECK: * Gooseneck in SNT design for optimized loading platform length, approx. 3,700 mm in length, with rear bevel approx. 1,000 mm x 10° * For tractor units: 4 x 2, 6 x 2, and 6 x 4 * Plug-in steel bulkhead, approx. 400 mm high * ASPÖCK-UNIBOX on the front connector panel with 24N, 24S & 15-pin sockets * 3 kW electro-hydraulic power unit for hydraulic operations (excluding hydraulic winches) * Gooseneck outer beam with fixture boreholes for screw-in lashing rings * One mounting hole in the upper rear area of the gooseneck outer beam for a screw-in lashing ring * 1 pair of screw-in lashing rings included (LC 10,000 daN) * On the gooseneck: 1 pair of plug-in anodized aluminum side walls, approx. 400 mm high * On the gooseneck: 1 plug-in anodized aluminum rear wall, approx. 400 mm high * Heavy-duty hardwood flooring, approx. 40 mm over the gooseneck * 2-inch kingpin * 1 crosswise stake pocket rail in the gooseneck floor in front of the bevel, for plug-in stakes approx. 100 x 50 mm Rsdpeyhkrlsfx Ag Ueu LOADING PLATFORM: * Extendable loading platform, approx. 8,800 mm long, with rear bevel approx. 500 mm x 10° * Recess in the loading platform, extending into the bevel, for excavator dipper stick, approx. 2,490 x 750 x 210/290 mm (L x W x H) * TPMS tire pressure monitoring system per ECE R 141 * BPW axles and suspension, 1st and 2nd axles fixed, 3rd and 4th axles steered * 3rd and 4th axles with electromagnetic reverse lock, activated via reverse gear and manually * Axle load capacity: 12,000 kg each, air suspension with raise/lower valve * Mechanical landing legs with 2-speed gearbox and crank * Hardwood flooring, approx. 50 mm thick, continuous and interrupted between axles (increases friction coefficient) * 1 intermediate table with recessed platform, approx. 300 mm wide, for the large-diameter extension tube with steel treadplate * 1 pair of lashing rings on the front cross-member (LC 10,000 daN) * 6 pairs of recessed, fold-out lashing rings in the outer frame (LC 10,000 daN) * Additional 1 pair of external lashing rings on the front cross-member, rotated approx. 90° towards the loading platform (LC 10,000 daN) * Extendable (galvanized) width extensions approx. 230 mm per side (without wood planks) * 1 pair of permanently installed open wheel recesses up to the extension, approx. 700 x 410 mm (W x D), in the deck ahead of the 1st axle * Between 2nd and 3rd axles, 1 pair of fixed wheel recesses approx. 1,695 x 700 x 410 mm (L x W x D) * 1 pair mechanical rear supports * 245/70 R 17.5 3PMSF twin tires – manufacturer of our choice HYDRAULIC LOADING RAMPS: * DR-15/60-900-4350-HB-HV-M * One pair of two-section steel ramps, approx. 4,350 mm long and 900 mm wide * Hardwood-covered hydraulically foldable ramp ends * Each ramp hydraulically adjustable approx. 235 mm outwards and 215 mm inwards * Hardwood decking on loading platform bevel * Ramps with hardwood overlay BRAKE SYSTEM: * WABCO EBS-E brake system compliant with EU regulations SURFACE TREATMENT: * HRM metallization of the entire chassis with ZINACOR 850 (85% zinc/15% a...

Condition: used, maximum load weight: 51,870 kg, overall weight: 65,000 kg, axle configuration: > 3 axles, first registration: 03/2025, next inspection (TÜV): 03/2026, total width: 2,540 mm, Equipment: ABS, You can find our entire vehicle inventory, including immediately and short-term available vehicles, on our website. Excerpt from the equipment list. Complete equipment details available upon request. GOOSENECK * Gooseneck in SNT design to optimize loading platform length, length approx. 3,700 mm, rear with chamfer approx. 1,000 mm x 10° * For tractors: 4 x 2, 6 x 2, and 6 x 4 * Plug-in steel front wall, approx. 400 mm high * At the front connection strip: yellow-red air couplings * ASPÖCK-UNIBOX on the front connection strip with 24N, 24S & 15-pin sockets * 3 kW electro-hydraulic power unit for hydraulic operations * External beams of the gooseneck with mounting holes for bolted lashing rings * One mounting hole at the rear upper part of the gooseneck external beam for a bolted lashing ring * 1 pair of screw-in lashing rings included (LC 10,000 daN) * On the gooseneck, 1 pair of plug-in side aluminum drop sides, approx. 400 mm high, anodized version * On the gooseneck, 1 plug-in aluminum rear wall, approx. 400 mm high, anodized version Rodpfxextc Uhj Ag Uju * Approx. 40 mm thick hardwood flooring above the gooseneck * 2-inch kingpin * Gooseneck guide plate for fifth wheel, approx. 500 mm wide * Rear gooseneck mounting for aluminum ramps * Round NATO socket at the front connection strip (Maeler & Kaege VG 96 917) LOADING PLATFORM * Loading platform, extendable version, length approx. 8,800 mm, rear with chamfer approx. 500 mm x 10° * Recess in the platform and chamfer for accommodating the excavator dipper stick approx. 2,490 x 750 x 210/290 mm (L x W x H) * TPMS tire pressure monitoring system in accordance with ECE R 141 * BPW axles and suspension * 1st and 2nd axle fixed, 3rd and 4th axles steering trailing axles * 3rd and 4th axles with electro-magnetic reverse lock, activated via reverse gear and manually * Technical axle load: 12,000 kg each * Air suspension with raise and lower valve * 235/75 R 17.5 3PMSF twin tires * Mechanical landing legs with 2-speed gearbox and crank, JOST Module B – static test load approx. 50,000 kg * Complete platform and interrupted between the axles with approx. 50 mm thick hardwood flooring (increasing the coefficient of friction) * Platform locking with conically welded locking profiles every approx. 250 mm * Elongated slots for insertable and repositionable bridging elements at the front of the platform * Intermediate table with set-down platform, approx. 300 mm wide, for large cross-section telescopic tube with sheet metal covering – front and rear with elongated slots for insertable and repositionable bridging elements – removable cover flush with the platform * 1 pair of lashing rings on the front cross member (LC 10,000 daN) * 6 pairs of flush-mounted lashing rings in the outside frame of the platform, foldable outward (LC 10,000 daN) * Additionally, 1 pair of lashing rings externally on the front cross member of the platform, approx. 90° turned inward towards the platform (LC 10,000 daN) * Extendable galvanized widening extensions by approx. 230 mm per side * 1 pair of permanently installed wheel recesses, open up to the extension, approx. 700 x 410 mm (W x D), sheet-covered in the platform ahead of the 1st axle, wheel recesses with square climbing strips approx. 15 x 15 mm, spaced approx. 200 mm * Between the 2nd and 3rd axles, 1 pair of permanently installed wheel recesses on the platform, approx. 1,695 x 700 x 410 mm (L x W x D), covers for wheel recesses split lengthwise, with wooden overlay, outer plug-in loc

Condition: new, maximum load weight: 50,400 kg, overall weight: 65,000 kg, axle configuration: > 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete vehicle inventory, including units available immediately and at short notice, on our website. Excerpt from the equipment list. Full equipment specifications available on request. GOOSENECK * Gooseneck in SNT design to optimize loading platform length, approx. 3,700 mm long, with rear bevel approx. 1,000 mm x 10° * For tractor units: 4 x 2, 6 x 2, and 6 x 4 * Removable steel front wall, approx. 400 mm high * ASPÖCK-UNIBOX on the front connector strip with sockets * 3 kW electro-hydraulic unit for controlling hydraulic operations, excluding hydraulic winches * 1 pair of removable aluminum side boards, approx. 400 mm high, anodized finish * 1 removable aluminum tailgate, approx. 400 mm high, anodized finish * Approx. 40 mm thick hardwood floor above gooseneck, checker plate floor above king pin * 2-inch king pin * Rear section of gooseneck prepared for aluminum drive-on ramps Redpfxetx Nwno Ag Uou * Round NATO socket on the front connection strip (Maeler & Kaege VG 96 917) LOADING PLATFORM * Extendable loading platform, approx. 8,800 mm long, with rear bevel approx. 500 mm x 10° * Recess in the loading platform and bevel for accommodating excavator dipper stick approx. 3,850 x 750 x 210/290 mm (L x W x H) * TPMS tire pressure monitoring system per ECE R 141 * BPW axles and suspension, 1st axle steerable, all remaining axles hydro-mechanically forced steered * 1st axle with electromagnetic reverse lockout, activated via reverse gear and manually * Technical axle load: 12,000 kg each, air suspension with raise and lower valve * Tires: 235/75 R 17.5, twin tires, 3PMSF * Mechanical landing legs with 2-speed gearbox and crank, JOST Module B – static test load approx. 50,000 kg * Continuous 50 mm thick hardwood floor on the loading platform and interrupted between axles (increases coefficient of friction) * 1 intermediate table, approx. 300 mm wide, for the extension tube with large cross-section * Extendable (galvanized) side extensions, approx. 230 mm per side (without wooden planks) * Wheel recesses with square climbing strips, approx. 15 x 15 mm ahead of axles, open through to gooseneck cross member, approx. 700 x 410 mm (W x D) * Aluminum covers for wheel recesses, usable as bridging elements for extension OR as widening planks * Aluminum elements lockable on telescopic tubes of the extensions * Widenable U-profiles for inserting ALU covers: - on the fixed section behind the gooseneck - on the intermediate table - on the extendable platform * Wheel recesses with square climbing strips, approx. 15 x 15 mm between 1st and 2nd axle, approx. 1,480 x 700 x 410 mm (L x W x D) * Aluminum covers for the wheel recesses, usable as bridging elements for the extension OR as widening planks * Aluminum elements lockable on the extension’s telescopic tubes * 1 pair of mechanical rear supports * Remote steering from front and rear via cable remote control, with axle tracking, without installation in the tractor unit HYDRAULIC LOADING RAMPS * One pair of two-section steel ramps, Type: DR-15/60-900-4350-KG-HV-M, approx. 4,350 mm in length and approx. 900 mm wide each * Hydraulically foldable ramp tips * Ramps can be shifted hydraulically approx. 235 mm outward and approx. 215 mm inward individually * Super Grip rubber surface approx. 25 mm and steel plate surface approx. 5 mm as additional

Condition: new, maximum load weight: 36,500 kg, overall weight: 48,000 kg, axle configuration: 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete vehicle inventory, including vehicles available for immediate and short-term delivery, on our website. A selection of features is listed below. Complete equipment upon request. GOOSENECK: * Gooseneck in SNT design to optimize the bed length, approximately 3,700 mm long, with a rear bevel of approximately 1,000 mm x 6° * For SZM (tractor unit): 4 x 2 and 6 x 2 * ASPÖCK-UNIBOX * The gooseneck and the rear bevel have a grid flooring with a 5 mm sheet metal reinforcement * 2-inch King Pin * Guide plate on the gooseneck for the turntable, approximately 500 mm wide * Round NATO socket on the connection strip at the front (Maeler & Kaege VG 96 917) * On the gooseneck, one pair of plug-in aluminum sideboards, approximately 400 mm high, in an anodized finish * One LED work light each on the left and right at the top of the front wall, with operation via an on/off switch (operation of the work lights from the SZM is not possible in this case) LOADING AREA: * Loading area, approximately 9,600 mm long, with a rear bevel of approximately 900 mm x 6° * The loading area behind the gooseneck can be hydraulically raised and lowered, approximately 3,000 mm long, with a load capacity of up to approximately 9,000 kg * Continuous grid flooring on the lifting platform and loading area with approximately 5 mm sheet metal underneath as additional reinforcement, designed for point loads TIRES: * 235/75 R 17.5 3PMSF, twin tires. Brand of our choice * TPMS tire pressure monitoring system in accordance with ECE R 141 AXLES: * BPW axles and suspension, 1st and 2nd axles rigid, 3rd axle trailing * 3rd axle with electro-magnetic reversing lock, activated via reverse gear and manually * 1st axle with starting assist * Technical axle load: 12,000 kg each * Air suspension with lift and lower valve HYDRAULIC LOADING RAMPS: * One pair of two-part AXS steel ramps with grid flooring, approximately 4,920 mm long and approximately 900 mm wide * Hydraulically foldable ramp tips * Ramps can be hydraulically shifted outwards by approximately 235 mm and inwards by approximately 365 mm individually * Strobe lights on the outside of the ramp tips, with a switch next to the ramp operation control * Ramp locking in the driving position by means of a quick-release fastener * Painted sand coating on the outer frame of the ramp and on the ramp tip * Mechanical supports in downpipe design on the sides of the ramps to provide support when docking with loading ramps * Control valves for the hydraulic ramps on the right side of the vehicle BRAKE SYSTEM: * Brake system from WABCO EBS-E, in accordance with EU regulations SURFACE TREATMENT: * HRM metallization of the entire vehicle chassis with ZINACOR 850 (85% zinc/15% aluminum) to ensure the best corrosion protection PAINTING: * Trailer: Carmine Red (RAL 3002) * Rims: Silver-grey * Sideboards: Aluminum, natural finish * Wheel hubs: According to axle manufacturer * Lamp panel: Pure white (RAL 9010) EQUIPMENT: * Front wall made of steel, plug-in, approximately 1,600 mm high, including connection strip for supply lines to the SZM, mounted approximately 1,000 mm from the bottom edge of the outer frame profile Redjy Auhhjpfx Ag Ueu * Attachment option for lashing chains on the inside of the front wall on the left and right, including aluminum trough underneath on the left and right for storing chains or lashing straps * Approximately 12 mm thick DELIGNIT flooring screwed to the back of the front wall * Two pairs of screwable lashing

Condition: new, overall weight: 80,000 kg, axle configuration: > 3 axles, total width: 2,540 mm, Equipment: ABS, More vehicles available. Excerpt from the equipment list below. Full equipment details on request. GOOSENECK: * Gooseneck in SNT design, optimized for loading platform length, approx. 3,700 mm long, with rear bevel approx. 1,000 mm x 10° * Suitable for tractors: 4 x 2, 6 x 2, and 6 x 4 * Detachable steel front wall, approx. 400 mm high * ASPÖCK-UNIBOX at the front connection rail with 24N, 24S & 15-pin sockets * 3 kW electro-hydraulic unit for controlling all hydraulic functions except hydraulic winches * Gooseneck outer rail with mounting holes for screwable lashing rings. First hole approx. 200 mm from front, then approx. every 400 mm. 2 pairs of screw-in lashing rings included (LC 5,000 daN) * 1 pair of horizontal lashing rings at rear part of gooseneck (LC 10,000 daN) * On the gooseneck: 1 pair of plug-in aluminum side walls, approx. 400 mm high, anodized finish * On the gooseneck: 1 plug-in aluminum rear wall, approx. 400 mm high, anodized finish * Approx. 40 mm hardwood floor covering on gooseneck, checker plate covering over kingpin * 3.5-inch kingpin * Gooseneck guide plate for the fifth wheel, approx. 500 mm wide * Round NATO socket at the front connection rail (Maeler & Kaege VG 96 917) * 2 pairs of lashing rings with retention spring hanging on the outer rails of the gooseneck (LC 5,000 daN) LOADING PLATFORM: * Extendable loading platform, length approx. 8,800 mm with rear bevel approx. 500 mm x 10° * Pneumatic locking with conical lock bolt and reinforced locking positions; supply lines routed securely inside the extendable rails, automatically adapting to the current platform length * BPW axles and suspension; 1st axle steerable, all others force-steered via hydro-mechanics * 1st axle with electro-magnetic reverse lock, activated via reverse gear and manually * Technical axle load: 12,000 kg each * Air suspension with lifting/lowering valve * 235/75 R 17.5 3PMSF twin tires – brand at our discretion * Mechanical landing gear with 2-speed gearbox and crank. JOST Modul B – static test load 50,000 kg * Full-length hardwood floor, interrupted between axles, approx. 50 mm thick (increases slip resistance). – Long slots for removable and repositionable bridging elements * At the front of the platform – 1 movable intermediate table, approx. 300 mm wide, for the large-cross-section sliding tube, with checker plate covering. – Front and rear with long slots for removable and repositionable bridging elements * 1 pair of lashing rings on front cross member (LC 10,000 daN) * 7 pairs of flush-mounted, fold-out lashing rings in the outer frame of the platform (LC 10,000 daN) * Extendable (galvanized) widened sections, approx. 230 mm per side (without wooden planks) * 1 pair of mechanical rear supports * Rear steering operable from front and rear via cable remote control, with single-track control of axles, without installation on the tractor Rodpfx Aoxarmajg Uju * TPMS tire pressure monitoring sensors fitted to all wheels * Deck locking with conically welded locking profiles every 500 mm * Lock monitoring left and right on the trailer * Mechanical lock for intermediate table (approx. 300 mm wide) to secure the table when extended * 5 pairs of threaded blocks mounted on the extendable rail for the installation of M20 screw-in rings (LC 5,000 daN) BRAKING SYSTEM

Condition: new, maximum load weight: 36,400 kg, overall weight: 48,000 kg, axle configuration: 3 axles, total width: 2,540 mm, Equipment: ABS, You will find our complete vehicle inventory, including immediately and soon-to-be available vehicles, on our website. Excerpt from the equipment. Full equipment details available upon request. - Gooseneck in SNT design to optimize load platform length, approx. 3,700 mm long, with a rear taper approx. 1,000 mm x 6° - For tractors: 4 x 2 and 6 x 2 - ASPÖCK-UNIBOX at the front connection panel with 24N, 24S & 15-pin sockets - 3 kW electro-hydraulic power pack for hydraulic operations (excluding hydraulic winches). Without supply line installation on the tractor unit - Outer beams of the gooseneck with mounting holes for boltable lashing rings. First hole approx. 200 mm from the front, subsequent holes approx. every 400 mm. 2 pairs of screw-in lashing rings included (LC 5,000 daN) - One mounting hole at the rear upper part of the gooseneck’s outer beams for a boltable lashing ring - 1 pair of screw-in lashing rings included (LC 10,000 daN) - 3 pairs of recessed lashing rings inside the gooseneck’s outer beams (LC 5,000 daN) - 3 pairs of recessed lashing rings in the center of the gooseneck (LC 5,000 daN) - 1 pair of recessed lashing rings at the rear center of the gooseneck (LC 5,000 daN) - Grating covering on the gooseneck and rear taper with 5 mm steel reinforcement - 2" kingpin - Round NATO socket at the front connection panel (Maeler & Kaege VG 96 917) - Spiral cable for powering the electro-hydraulic unit and/or electric winch (approx. 35 mm², approx. 3.5 m long) between trailer and tractor unit, with plug (NATO-NATO) - 1 pair of detachable aluminum side boards on the gooseneck, approx. 400 mm high, anodized finish CARGO AREA: - Cargo area, approx. 9,600 mm long, with rear taper approx. 900 mm x 6° - Cargo area behind the gooseneck hydraulically liftable and lowerable, approx. 3,000 mm long, load capacity up to approx. 9,000 kg - TPMS (Tire Pressure Monitoring System) according to ECE R 141 - BPW axles and suspension, 1st and 2nd axles fixed, 3rd axle with trailing steering. 3rd axle with electromagnetic reverse lock via reverse gear and manual activation - Technical axle load: 12,000 kg each - Air suspension with lift and lower valve - 235/75 R 17.5 3PMSF twin tires. Brand of our choice, load index 143/141J (144/144F) - Mechanical landing legs with 2-speed gearbox and crank - Continuous grating flooring with approx. 5 mm steel plating for additional reinforcement, designed for point loads: on the lift bed and cargo area - Painted sand coating on the gooseneck cover plates as well as transition areas between neck and lift bed, lift bed and cargo area, and cargo area and ramps - 1 spare wheel mounting bracket under the cargo area to the right in front of the axles Rodpfx Aoyhkqueg Uju - Cut-outs in the outer frame of the cargo area and lift bed for attaching tie-down straps (LC 2,000 daN) - 11 pairs of recessed, fold-out lashing rings in the outer frame of the cargo area (LC 10,000 daN): 3 pairs in the lift bed outer frame, 8 pairs in the cargo area outer frame - 11 pairs of recessed lashing rings along the central beam (LC 5,000 daN): 3 pairs in the lift bed, 8 pairs in the rear cargo area - Control valves for the hydraulic ramps located on the right side of the vehicle - 1 pair of foldable mechanical rear supports, single-hand operation HYDRAULIC LOADING RAMPS: - 1 pair of two-part AXS steel ramps, approx. 4,920 mm long, and a

Condition: new, maximum load weight: 67,200 kg, overall weight: 85,000 kg, axle configuration: > 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete vehicle inventory, including immediately and short-term available vehicles, on our website. Excerpts from the equipment. Full specifications available upon request. GOOSENECK * Gooseneck in SNT design to optimize load floor length, approx. 3,700 mm long, with rear bevel approx. 1,000 mm x 10° * For tractors: 6 x 2, 6 x 4, and short 8 x 4 * Detachable steel front wall, approx. 400 mm high * 3 kW electro-hydraulic power unit for controlling hydraulic functions, except for hydraulic winches * Outer beams of the gooseneck with mounting holes for bolt-on lashing rings * 2 pairs of screw-in lashing rings included (LC 5,000 daN) * 1 pair of flat lashing rings at the rear of the gooseneck (LC 10,000 daN) * 1 pair of plug-in aluminum side boards, approx. 400 mm high, anodized * 1 plug-in aluminum rear board, approx. 400 mm high, anodized * Approx. 40 mm thick hardwood flooring above gooseneck, checker plate flooring above kingpin * 3.5 inch kingpin * Gooseneck guide plate for the fifth wheel plate, approx. 500 mm wide * Round NATO socket at the front connection strip (Maeler & Kaege VG 96 917) * In addition to the electro-hydraulic unit, a truck hydraulic connection with flow regulator, including bracket for hanging supply lines (Faymonville couplers) * 2 pairs of stake pockets recessed in the gooseneck, for plug-in stakes approx. 100 x 50 mm LOAD FLOOR * Extendable load floor, approx. 11,000 mm long, with rear bevel approx. 500 mm x 10° * Pneumatic locking with conical locking bolts and reinforced locking positions; supply lines are protected inside the extendable beams and automatically adjust to the respective deck length * BPW axles and suspension, 1st axle steered, 2nd axle fixed, all other axles hydro-mechanically forced steered * 1st axle with electro-magnetic reverse lock via reverse gear and manual activation * Axle load capacity: 12,000 kg each Rsdpfx Ajrgzv Nog Uju * Air suspension with lift and lower valve * 235/75 R 17.5 3PMSF twin tires * Mechanical landing gears with 2-speed gearbox and crank. JOST Modul B – static test load = approx. 50,000 kg * Continuous and, between axles, interrupted approx. 50 mm thick hardwood floor on load deck (increases coefficient of friction) * Slotted holes for attachable and repositionable bridging elements: – at the fixed part behind the gooseneck – on the front of the load floor * 1 sliding intermediate table, approx. 500 mm wide, for the sliding tube with large cross-section, checker plate flooring, front and rear with slotted holes for attachable and repositionable bridging elements * 1 pair of recessed flat lashing rings in the front fixed part of the load floor (LC 10,000 daN) * 9 pairs of recessed lashing rings, foldable outward, in the load floor perimeter frame (LC 10,000 daN) * 1 pair of mechanical rear supports * Remote steering from front and rear via cable remote control, with axle tracking control, no installation required in the tractor * 1st axle with automatic lift axle function and start-up assist according to EU Regulation 2021/535 * Under the gooseneck and at the rear cross member, left and right, a 7-pin socket each with holder for warning signs * Factory-applied sand coating on the perimeter frame of the load floor as well as the checker plates and the transition area between load decks

Condition: new, maximum load weight: 73,540 kg, overall weight: 102,000 kg, axle configuration: > 3 axles, Equipment: ABS, You can find our complete vehicle inventory, including vehicles available for immediate and short-term delivery, on our website. Excerpt from the equipment list. Complete equipment list available upon request. Gooseneck: * Hydraulically extendable/retractable and lowerable gooseneck, length ± 3,650 mm * 2 pairs of lashing rings, foldable outwards (LC 5,000 daN) * 2 pairs of lashing rings on the gooseneck (LC 10,600 daN) * 1 pair of lashing rings in the middle section of the gooseneck (LC 10,600 daN) * Suitable for 6 x 4 or 8 x 4 tandem axle vehicles Compact front axle: * Hook receiver at the front and rear, length: approx. 2,200 mm * Axle width: approx. 2,850 mm Excavator bridge: * Telescopic excavator bridge with traversable bridge hooks at the front and pin-and-plate coupling at the rear * Overall width: approx. 2,850 mm * Length: approx. 6,650 mm * Beam height: approx. 400 mm * Beam width: approx. 1,350 mm * Loading height approx. 550 mm with ground clearance approx. 150 mm Rjdpfxsxbmplo Ag Usu 4-axle rear axle: * Mechanical pin-and-plate coupling for mounting a low-bed trailer at the front * End crossbeam at the rear, axle width: approx. 2,850 mm * Axle length: approx. 5,480 mm Swivel axles, all axles hydro-mechanically force-locked * Technical axle load: 14,640 kg each (62 km/h) * Hydraulic axle suspension Tires: * Front axle: * 8 x tires, selection according to manufacturer (M+S) 285/70 R19.5 * Rear axle tires: * 16 x tires, selection according to manufacturer (M+S) 285/70 R19.5 * Load index 150/148J Painting: * Complete steel construction automatically blasted with a shot blasting system after welding. Second blasting with corundum for optimal adhesion of the coating system. * HRM metallization of the entire vehicle chassis with ZINACOR 850 (85% zinc/15% aluminum) to ensure the best corrosion protection. * Final painting with 2 layers of 2K topcoat, single-color in RAL 3002 carmine red, according to the RAL 841GL system. Including the following accessories: * Steel front panel, approx. 400 mm high * Aluminum side and rear walls, pluggable on the gooseneck, approx. 400 mm high, in anodized finish * 3.5-inch kingpin * Truck hydraulic connection with flow control (20 l/min) * Gantry for suspending the supply lines; the SZM tank must have a minimum capacity of 80 liters. * With MAX Trailer coupling parts; otherwise, coupling parts must be supplied by the customer. * BEKA-MAX central lubrication for one gooseneck with standard grease NLGI-2 * Tool kit, type No. 612452 * Multi-coupling hydraulic connections on the gooseneck * Front axle with a separate air connection for air suspension * BEKA-MAX central lubrication for a 2-axle axle with standard grease NLGI-2 * One 7-pole socket on the left and right at the rear of the front axle for warning signs * Screw-in option (approx. 40 mm diameter) every approx. 500 mm on the outside of the top chord of the outer beam of the excavator bridge for screw rings (LC 16,000 daN) * Foldable wideners with steel mats, adjustable in width from approx. 2,850 mm to approx. 3,250 mm * BEKA-MAX central lubrication for a 4-axle axle with standard grease NLGI-2 * On the rear axle, a socket for the cable remote control of the trailing axle * Rear axle with tipper body * Two INOX toolboxes, approx. 855 x 340 x 390 mm, on the gooseneck, left and right * 1-cylinder Hatz diesel engine (Silent Pack) with electric starter and starter battery * Radio remote control: * Operation of the power pack, start/stop of the diesel engine

Condition: new, maximum load weight: 96,500 kg, overall weight: 126,000 kg, axle configuration: > 3 axles, loading space length: 26,900 mm, total width: 2,750 mm, Equipment: ABS, You can find our complete vehicle inventory, including vehicles available for immediate and short-term delivery, on our website. Excerpt from the equipment list. Complete equipment list available upon request. Gooseneck: * Hydraulically extendable/retractable and lowerable gooseneck. Length approx. 3,650 mm * For semi-trailer with multiple axles (SZMs): 6 x 4 or 8 x 4 * Truck hydraulic connection with flow control (20 l/min), incl. gantry for suspending the supply lines, the SZM tank must have a minimum capacity of 80 l * With MAX Trailer coupling parts, otherwise coupling parts must be supplied by the customer * Gantry with winch for spare wheel on the front of the gooseneck * 3.5-inch kingpin * Steel front panel approx. 400 mm high * Plug-in aluminum side and rear panels on the gooseneck, approx. 400 mm high, in anodized finish * Control levers on the gooseneck protected by a folding cover * Lighting for the controls on the gooseneck with on/off switch * A 7-pin socket on the left and right at the rear of the gooseneck for the warning sign * BEKA-MAX central lubrication system for a gooseneck with standard grease NLGI-2 * Hydraulic connections from the gooseneck to the low-bed with screw couplings * Access to the gooseneck * Four warning signs that can be extended by approx. 1,000 mm, approx. 423 x 423 mm, with an LED position light and a mounting bracket for a rotating beacon * Mounting adapter for 2 spare wheels * 1-cylinder Hatz diesel engine (Silent Pack) with electric starter and starter battery. Power: 9.5 kW (12.9 hp) at 3000 rpm * Hydraulic connection lines between the power pack and the connector plate on the gooseneck * 1 LED work light on the left and right at the rear of the gooseneck with separate on/off switch * Radio remote control: - Operation of the power pack, start/stop of the diesel engine. - Operation of the trailing axle steering, in addition to the cable remote control, with 2 LED indicator lights on the receiver as a single-axle control. - Operation of raising/lowering the gooseneck - Operation of raising/lowering the suspension of the chassis 2-axle front bogie: * Bolt-on coupling at the front and rear. Length: approx. 2,970 mm. Chassis width: approx. 2,750 mm Rjdpfszahp Sjx Ag Ueu * BEKA-MAX central lubrication system for a 2-axle chassis with standard grease NLGI-2. (not connected to the track rods) * A 7-pin socket on the left and right at the rear of the front bogie for the warning signs * Surface of the chassis with a sand-blasted coating for slip resistance * Yellow reflector tape according to EU regulations on the side, on the extension, and at the rear of the trailer * A 7-pin socket for the warning signs, on the left and right on the front chassis, in the area of the axles * Extendable widening elements by approx. 230 mm on each side for a 2-axle chassis * 1 pair of M42 threaded blocks between the axles of the front bogie * 1 pair of brackets for the warning signs for insertion into the pocket recesses in the outer frame of the loading platform Loading platform: * 6-axle double-extendable loading platform with bolt-on coupling at the front and a slope of approx. 500 mm x 8° at the rear * Loading platform length: approx. 11,000 mm * Technically extendable by: approx. 8,200 + 7,700 mm * Axle spacing: approx. 1,500 mm * Basic width: approx. 2,750 mm * Hydraulic coupling pin * BEKA-MAX central lubrication system for the loading platform with standard grease NLGI-2 * Surface of the loading platform with a sand-blasted coati

Condition: excellent (used), axle configuration: > 3 axles, permissible axle load (axle 1): 12,000 kg, permissible axle load (axle 2): 12,000 kg, permissible axle load (axle 3): 12,000 kg, loading space length: 17,320 mm, loading space width: 3,200 mm, loading space height: 400 mm, total length: 17,320 mm, total width: 3,200 mm, suspension: hydraulics, tire size: 245/70 R 17.5 | 143/131L (146/146F), color: beige, Year of construction: 2021, Colour: Yellow Loading capacity: 64,800 kg Main Features Manufacturer: Faymonville Model: GigaMax 1+4 / F-S45-2GXX Chassis number: YAFTL1009M0027562 Year of manufacture: 2021 Rsdovzaanspfx Ag Uju Weights / Payload King-pin load: 25,000 kg Axle load: 12,000 kg Total axle load: 12,000 kg x 5 = 60,000 kg Gross vehicle weight (GVW): 84,200 kg Unladen weight: 20,200 kg Pay load: 64,800 kg Axles Pendle axles Hydraulic suspension All axles with hydraulic steering WABCO braking system with EBS-E Tyres: 245/70 R 17.5 | 143/131L (146/146F) Dimensions Overall length: 17,320 mm Loading platform length: 6,800 mm 2 extension beams: 2,000 mm / 3,000 mm Loading platform width: 2,750 mm / 3,200 mm Loading platform height: 400 mm Ground clearance: 150 mm King-pin height: +/- 1,340 mm Additional Equipment: Gooseneck with integrated 1-axle pendle axle Hatz Diesel power pack Hydraulically operated gooseneck Aluminium side boards on gooseneck 2 extension beams: 2,000 mm / 3,000 mm Excavator trough Lashing rings Stainless steel toolbox Spare wheel + holder Rear bumper with lights King-pin 3.5” Central greasing system with 2 BEKAMAX pumps = Further information = General Information Year of manufacture: 2021 Axle Configuration Tyre size: 245/70 R 17.5 | 143/131L (146/146F) Suspension: hydraulic suspension Front axle: Double wheels; lift axle; max. axle load: 12,000 kg; steered Rear axle 1: Double wheels; lift axle; max. axle load: 12,000 kg; steered Rear axle 2: Double wheels; lift axle; max. axle load: 12,000 kg; steered Rear axle 3: Double wheels; lift axle; max. axle load: 12,000 kg; steered Rear axle 4: Double wheels; lift axle; max. axle load: 12,000 kg; steered Weights Unladen weight: 20,200 kg Payload: 64,800 kg Gross vehicle weight: 85,000 kg Functional Loading platform height: 40 cm Extendable body: Yes Condition Technical condition: Very good Visual condition: Very good Financial information Price: On request Further information For more information, please contact Stefan Schaapveld.

Condition: new, maximum load weight: 38,953 kg, overall weight: 49,500 kg, axle configuration: 3 axles, Year of construction: 2026, MAX100-N-3B-9.30-U Technical data Speed: 80 km/h Total weight: 49,500 kg Fifth wheel load: 18,000 kg Axle load: 31,500 kg Empty weight (+/- 3%): 10,547 kg Payload approx.: 38,953 kg Rodpfxsg Sk Trs Ag Ueu Gooseneck length: 3,850 mm Fifth wheel height loaded: 1,200 mm Loading area length: 9,300 mm Extendable by: 0 mm Axle spacing: 1,360 mm Rear steering radius: 2,300 mm Loading height with max. load: 860 mm Total width: 2,540 mm Suspension travel: -55/ +145 mm Technical description Gooseneck: Gooseneck with bevelled corners 45° at the front and with a rear bevel of approx. 750 mm x 10°. 3 pairs of lashing rings (LC 5,000 daN). Hardwood flooring 30 mm thick. Loading area: Loading area can be raised and lowered hydraulically after the gooseneck, length approx. 2,800 mm, with a rear bevel of approx. 1,000 mm x 8°. 6 pairs of lashing rings that can be folded outwards (LC 5,000 daN). 2 pairs of lashing rings that can be folded outwards (LC 10,000 daN). 1 pair of tension rings that can be folded inwards on the central support at the front (LC 10,000 daN). Cutouts in the outer frame of the loading area for hanging tensioning straps. (LC 2000 da N). Hardwood flooring approx. 48 mm thick, checkered sheet flooring over the axles. Ramps: Two-part steel ramps A pair of galvanized two-part steel ramps approx. 2,750 + 1,400 x 800 mm with approx. 48 mm thick hardwood flooring. Ramp with hydraulically foldable and unfoldable ramp sections, hydraulic lifting mechanism and hydraulically movable. Maximum load per pair: 40,000 kg Seat supports: JOST seat supports (mechanical) with 2-speed gearbox for 24t lifting load (50t test load). Tires: 235/75 R 17.5 tires as selected by the manufacturer. Axle: SAF axles, air-sprung, with drum brake, with lifting/lowering function. The last axle is self-steered with an electro-magnetic reversing lock can be activated via reverse gear or manually. Axle tool. Braking system: Braking system in accordance with EU regulations with EBS-E (2S2M) without connecting lines to the tractor unit. Steel construction: Steel construction made of high-strength fine-grain steel. Steel qualities: S355J2+N/S355MC (yield strength 355MPa) S690QL/S700MC (yield strength 690MPa) Paintwork: First-class and long-lasting corrosion protection of the standard shot-blasted welded frame guaranteed by a 2-component (2K) zinc dust primer. A high-quality 2-component (2K) top coat in a single color in RAL colors of your choice. Rear section metallized and painted in RAL 9010 (pure white). No metallic paint possible. Electrical system: Electrical system in accordance with EU regulations, lighting LED 24 Volt ASPÖCK-NORDIK (ASS3) ASPÖCK-UNIBOX on the connection panel at the front with sockets 24N, 24S & 15-pin. Connection in accordance with ISO. 24N ISO-1185 24S ISO-3731 15-pin ISO-12098 Accessories included 2" kingpin A galvanized steel bulkhead approx. 400 mm high. Yellow-red air couplings on the galvanized connection strip at the front. 4 pieces of chocks with holder on the bulkhead. (± 5kg) Cable for supplying the electro-hydraulic unit and/or the electric cable winch (35mm², 3.5 m long, max. 250A) between the trailer and tractor unit with plug connection (ANDERSON-ANDERSON) Galvanized folding supports under the slope of the loading area. A bracket for a rotating beacon at the rear of the trailer. Control valves for the ramps attached to the right-hand side of the trailer. (± 4kg) Yellow reflector tape in accordance with EU regulations on the side and rear of the Trailer.

Condition: new, maximum load weight: 34,104 kg, overall weight: 47,000 kg, axle configuration: 2 axles, Year of construction: 2026, Further information here: Rsdpfx Ajv D Abgog Ueu

Condition: used, overall weight: 45,000 kg, axle configuration: 3 axles, first registration: 09/2017, * SAF axles * Wheel recesses * Hydraulic loading ramps, width adjustable * Air suspension * Extendable Redowta Aljpfx Ag Uju * Unladen weight: 11,020 kg -----Internal vehicle number: 11010----Subject to errors and prior sale. WhatsApp support available! If you have questions about the vehicle or need further information, feel free to contact us conveniently via WhatsApp. WhatsApp: German, English -- WhatsApp: German, English, Arabic

Condition: used, Year of construction: 2014, Please contact Theo Lelie for more information Rsdpoxtqkwofx Ag Ueu

Condition: excellent (used), Condition: used, shows normal signs of use, fully operational Manufacturer: Vetter (Germany) Country of manufacture: Germany 📦 The set includes: 2x Vetter air lifting bag Type 1/6 complete set of air hoses (yellow + red) quick couplings carrying bag the set exactly as shown in the photos ⚙️ Technical specifications: Model: Type 1/6 Maximum lifting capacity: approx. 3.2 t (32 kN) – each bag Max. operating pressure: 0.5 bar Volume: approx. 403 L Air requirement: approx. 603 L Hoses: DN 19 mm working pressure 1 bar (14.5 PSI) ISO standard 🛠️ Applications: technical rescue (fire department) lifting of vehicles and machinery workshops and industry maintenance and emergency operations 📌 Additional information: renowned German manufacturer – Vetter complete set, ready for immediate operation Rjdpey Af Tnefx Ag Usu solid, durable construction fast and safe lifting of heavy elements sold as shown in the photos

Condition: new, maximum load weight: 30,190 kg, overall weight: 43,000 kg, axle configuration: 2 axles, Equipment: ABS, You can find our complete vehicle inventory, including immediately and short-term available vehicles, on our website. Extract from the equipment list. Full equipment details available on request. Loading Platform: - Lowbed with external beams in extendable SUPER LOW design, length approx. 6,850 mm - Lowbed with fixed hardwood floor approx. 40 mm thick and mechanical locking mechanism - Supply lines protected inside the extendable side rails, automatically adjusting to the current bed length - 5 pairs of lashing rings, foldable outward (LC 10,000 daN) - 6 pairs of threaded blocks on the inner beam for attaching RUD screw-on rings Gooseneck: - Gooseneck in SNT design for optimized platform length, length approx. 3,750 mm - Gooseneck hydraulically liftable/lowerable and detachable - Technical fifth wheel load: 23,000 kg - For tractors: 4x2, 6x2 Rear Chassis: - Rear chassis in short version with closed external frame and checker plate cover - Running gear with excavator recess, closed in the rear half to accommodate the air tanks - 2 pairs of lashing rings, foldable outward (LC 5,000 daN) - 1 pair of lashing rings, foldable outward (LC 10,000 daN) - 1 pair of lashing rings horizontal, front & rear of the chassis (LC 10,000 daN) Axles: - BPW axles, hydro-mechanically forced steering - Technical axle load per axle: 12,000 kg - Air suspension with lift and lower valve Rodpfx Agoxarl Ns Usu Tyres: - Tyres 245/70 R 17.5 3PMSF - Manufacturer of our choice - Load index (146/146F) - TPMS tyre pressure monitoring system in accordance with ECE R 141 - Data transmission to the truck via the standardized EBS interface in accordance with ISO 11992 - The truck must be capable of processing and displaying this data for correct operation Braking System: - Braking system according to EU regulations with EBS-E (2S2M) Electrical System: - Electrical system according to EU regulations, lighting 24 Volt ASPÖCK-NORDIK (ASS3) - All LED side marker lights flash with indicators - ASPÖCK-UNIBOX at the front connection point with 24N, 24S, and 15-pin sockets as per standards: - 24N ISO-1185 - 24S ISO-3731 - 15-pin ISO-12098 Steel Construction: - Steel construction from high-strength fine-grained steels - Steel grades: S355J2+N/S355MC (yield strength 355 MPa) S690QL/S700MC (yield strength 690 MPa) Paintwork: - Complete steel structure is automatically shot-blasted after welding using a blasting turbine system - Second blasting process with corundum for optimal adhesion of coating system - HRM metallization of complete chassis with ZINACOR 850 (85% zinc / 15% aluminum) to ensure maximum corrosion protection - Final paint finish with 2 coats of 2K topcoat, single color in RAL 3002 Carmine Red, as per RAL system 841GL - Rims in silver - Rear section metallized and painted RAL 9010 (Pure White) - Metallic paint not possible - Paint system tested in salt spray test as per ISO 9227-NSS - Cavities sealed with special wax Including the following additional equipment: - 2" King pin - One galvanized steel front wall, approx. 400 mm high - Remote steering of front and rear axles by cable remote control with pushbuttons, including single track axle monitoring (without installation in the tractor unit) - Hydraulic connections from gooseneck to lowbed with multi-coupling instead of screw couplings - Electro-hydraulic power pack - Preparation for mounting container locks for 1x 20' or 1x 40' container on the external beams - Without container locks

Condition: good (used), GUK K50/4/1/FL 2-50 Automatic Folding Machine Machine in perfect condition, ready for production. Format: 500x700mm. Folding speed: 30-160m/min Equipment: 4 parallel cassettes electronically adjusted via computer 1 cross-cut knife Rodsy Tu N Hspfx Ag Uou First cassette extended. Continuous speed control via inverter control panel Counter with batching function and folding speed indicator. Rietschle compressor. Raised soundproofing hood. Tool roller for mounting tools such as perforation, creasing, and cutting. FL2-50 feeder with vacuum unit Window cassette with control unit. Mobile delivery with continuous speed control.

Condition: used, maximum load weight: 36,100 kg, overall weight: 49,000 kg, axle configuration: 2 axles, first registration: 10/2024, next inspection (TÜV): 10/2026, total width: 2,550 mm, Equipment: ABS, You can find our complete vehicle inventory with vehicles available immediately and in the short term on our website. Excerpt from the equipment list. Complete equipment available upon request. Gooseneck: * Gooseneck in SNT design to optimize the loading area length, approximately 3,750 mm long, hydraulically extendable/retractable and adjustable. * Technical saddle load: 25,000 kg * For semi-trailer tractor: 4 x 2, 6 x 2, and 6 x 4 Low-bed: * Low-bed designed as a telescoping bolster bridge in a low-profile design with an extension at the front and a mechanical locking mechanism. * Length x width approximately 6,850 mm x 2,540 mm * The supply lines are protected in the extendable beams and automatically adjust to the respective low-bed length. Axles and Suspension: * PENDEL-AXLE * All axles are hydro-mechanically force-steered. * Hose burst valve on the axle equalization system. * Cylinders with automatic RESET function. * Hydraulic cylinders with shut-off valves and a connector for securing in the raised position. * Technical axle load: 12,000 kg each. * Hydraulic axle equalization. * Tires: 245/70 R 17.5 * Rear chassis: rear chassis with a closed outer frame, with a diamond-plate cover and a continuous prismatic excavator well, approximately 1,250/700 x 505 mm, open at the rear. Braking System: * Braking system from WABCO EBS-E, in accordance with EU regulations, without a connecting cable to the semi-trailer tractor. Rjdpfjx Uvllsx Ag Ueu Paintwork: * Color of the semi-trailer: RAL 3002 carmine red. Included Accessories: * Steel front wall, plug-in, approximately 400 mm high. * 3 kW electric-hydraulic unit for controlling the hydraulic operations, with the exception of hydraulic winches, without installation of the supply connections on the semi-trailer tractor. * Outer beam of the gooseneck with mounting holes for screw-on lashing rings. The first hole is approximately 200 mm from the front, then every approximately 400 mm. 2 pairs of screw-on lashing rings included (LC 5,000 daN). * 1 lashing ring on the left and right sides on the rear slope of the gooseneck (LC 6,000 daN). * 2-inch kingpin. * One locking point every approximately 500 mm on the extension. * 1 pair of steel ramps with climbing strips and fastening bolts for bridging the mounting hooks of the low-bed. * 1 lashing ring on the left and right sides on the front cross member (LC 10,000 daN). * Lashing rings with retaining spring every approximately 1,200 - 1,300 mm on the outside of the inner beams of the loading area. * Lashing rings with retaining spring every approximately 1,200 - 1,300 mm on the outside of the outer beams of the loading area (LC 10,000 daN) on the upper chord of the outer beams. * Recesses above the lashing rings. * 1 lashing ring hanging on the outside on the left and right sides on the rear cross member (LC 10,000 daN) on the outer beams of the loading area. * Preparation for the removable loading floor. * Mounting rail at the front of the rear chassis for the low-bed for loose loading ramps. * Chassis with beveled corners at the rear. * Mounting rail for loose aluminum loading ramps on the end cross member of the vehicle. * Steerable from the front and rear via cable remote control with push buttons, with single-axle control, without installation in the semi-trailer tractor. * Mechanical pin-tab coupling from the low-bed to the chassis, for changing the loading area or installing extension beams, with electric-pneumatic-hydraulic couplings. * Round NATO socket

Condition: new, For sale: professional electronic circulation pump Wilo Stratos 50/1-9 – high-efficiency, energy-saving, designed for heating and cooling systems. Technical specifications Manufacturer: Wilo Rjdoyhhn Depfx Ag Uou Model: Stratos 50/1-9 Power supply: 1~ 230 V, 50/60 Hz Power: 25–490 W Current: 0.20–2.15 A Connection: DN50 (2”) Connection: flanged Operating pressure: PN6 / PN10 Protection class: IPX4D Max. medium temperature: up to 110°C Energy Efficiency Index: EEI ≤ 0.20 (ErP) Year of manufacture: 2015 Made in: Germany Condition Technically fully functional Very good visual condition Condition as shown in the photos Applications Heating systems Cooling systems Industrial and commercial buildings 📦 Possible shipping or personal collection 🧾 Invoice available 🌍 Export sales also possible

Condition: used, maximum load weight: 34,030 kg, overall weight: 48,000 kg, axle configuration: 3 axles, first registration: 07/2025, next inspection (TÜV): 07/2026, total width: 2,480 mm, Equipment: ABS, You can find our complete stock of immediately and short-term available vehicles on our website. Excerpt from the equipment. Complete specification available upon request. Gooseneck: * Gooseneck with rear bevel approx. 750 mm x 10°, 3 pairs of lashing rings (LC 5,000 daN) * Hardwood flooring approx. 30 mm thick loading surface, hydraulically liftable and lowerable loading area behind the gooseneck, approx. 2,800 mm long, with rear bevel approx. 1,000 mm x 8° * 6 pairs of fold-out lashing rings to the outside (LC 5,000 daN) * 2 pairs of fold-out lashing rings to the outside (LC 10,000 daN) * 1 pair of fold-in lashing rings to the inside on the front central beam (LC 10,000 daN) * Grating surface C40/4 (point load approx. 2.3 t on an area of approx. 20 x 20 cm) over the axles, checker plate covering Two-part steel ramps: * One pair galvanized two-part steel ramps, reinforced design, approx. 3,185 + 1,420 x 1,250 mm, with grating surface C40/5 (point load approx. 8 t on an area of appr. 20 x 20 cm) * Ramps with hydraulically extendable and retractable sections and hydraulic lifting device, maximum load per pair: 40,000 kg * In accordance with regulation 1230/2012/EU, ramps with a length less than 300 mm in driving position do not have to be included in the total vehicle length of 16,500 mm Landing gear: * JOST mechanical landing legs with 2-speed gearbox for approx. 24 t lifting capacity (approx. 50 t test load) * Tires 235/75 R 17.5 3PMSF * TPMS tire pressure monitoring system according to ECE R 141 Axles: * BPW axles and suspension * 2 rigid axles, 1 self-steering trailing axle * Technical axle load: 12,000 kg each * Electromagnetic reverse lock, activated via reverse gear and manually * Air suspension with lift and lower valve Braking system: * WABCO braking system according to EU regulations with EBS-E (2S2M) Colors: * Trailer in RAL 3002 carmine red * Rims silver * Tarp in RAL 9006 silver Including accessories: * 1 spare wheel carrier under the loading area, right-hand side in direction of travel * 2-inch kingpin * One galvanized steel front wall * Yellow-red air couplings on the galvanized connection bar at the front * 4 wheel chocks with holders on the front wall * 3 levels of wooden slats * Galvanized folding supports under the rear slope of the loading platform * Adjustable curtain body height approx. 3,960 mm Rsdpfey Nu Hksx Ag Uju * Galvanized front wall with tension mechanism for sliding curtains * Roof from EDSCHA, adjustable in height by approx. 400 mm, can be slid forward on aluminum roof beam profiles (bolted to front and rear wall) * 3 pairs of sliding stakes in the loading area * Body hydraulically extendable by approx. 750 mm left and right at the rear * Sliding tarp with approx. 700 mm length reserve, tension straps at approx. 600 mm intervals in height * Top edge of body approx. 3,960 mm (laden) * Driving with open sliding roof is not permitted and will damage the tarp * A painted sand layer as anti-slip coating on the gooseneck and loading area checker plates * Cover plates to bridge the gap between ramps and loading area * Electro-hydraulic unit at the rear under the loading area * Mountings for warning boards, including socket, on the left and right of the gooseneck and ramps * Ramp control valves installed on the right side of the trailer * Grating in the gooseneck slope C30/3 (point load approx. 2 t on an area of 20 x 20 cm) * Grating in the slope of the load f

Condition: new, maximum load weight: 58,860 kg, overall weight: 73,000 kg, axle configuration: > 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our entire vehicle inventory, including vehicles available for immediate and short-term delivery, on our website. Extract from the equipment; complete equipment list available upon request. Gooseneck: * Gooseneck with front corners beveled approx. 45° and rear bevel approx. 750 mm x 10° * 3 pairs of lashing rings (LC 5,000 daN). Hardwood flooring approx. 30 mm thick Extendable loading platform: * Extendable loading platform with rear bevel approx. 500 mm x 8° * 8 pairs of fold-out lashing rings (LC 10,000 daN) * 1 pair of recessed lashing rings at the front of the loading platform (LC 10,000 daN) * Cut-outs in the outer frame of the loading platform for attaching tension straps (LC 2,000 daN) * Hardwood flooring approx. 48 mm thick, over the axles with checker plate Two-part steel ramps: * Pair of galvanized two-part steel ramps, approx. 2,750 + 1,400 x 900 mm, with Super Grip rubber coating * Ramps with hydraulically folding ramp sections * Hydraulic lifting device, hydraulically adjustable * Maximum load per pair: 50,000 kg * In accordance with Regulation 1230/2012/EU, ramps shorter than 300 mm in transport position are not included in the overall vehicle length of 16,500 mm Axles: * BPW axles and suspension, 1st axle steering, 2nd and 3rd axles rigid, 4th and 5th axles trailing steering, air suspension with lift/lower function, drum brakes * Trailing steering axles with electromagnetic reverse lock, activated via reverse gear or manually * Technical axle load: 12,000 kg each Tyres: * Tyres 235/75 R 17.5 3PMSF – brand at our discretion TPMS: * TPMS tyre pressure monitoring system according to ECE R 141. Data is transmitted to the tractor unit via the standardized EBS interface (ISO 11992). For correct readout, the tractor unit must be capable of transmitting and displaying these data. Landing legs: * JOST landing legs (mechanical) with 2-speed gearbox, lifting capacity approx. 24 t (tested to approx. 50 t) Brake system: * Wabco brake system compliant with EU regulations, with EBS-E (4S3M), without connecting lines to the tractor unit Steel construction: * Steel structure made of high-strength fine-grained steels * Steel grades: S355J2+N/S355MC (yield strength 355 MPa), S690QL/S700MC (yield strength 690 MPa) Electrical system: * Electrical system according to EU regulations; 24 volt ASPÖCK-NORDIK lighting (ASS3) Redpfxjy Augwe Ag Usu * All LED side marker lamps flash with the indicators * ASPÖCK-UNIBOX on the front connection rail with 24N, 24S, and 15-pin sockets as per ISO: 24N ISO-1185, 24S ISO-3731, 15-pin ISO-12098 Paintwork: * Entire steel structure automatically blasted after welding using a centrifugal blasting machine * Second blasting step with corundum grit for optimal coating adhesion * HRM metallisation of the entire vehicle chassis with ZINACOR 850 (85% zinc/15% aluminum) for maximum corrosion protection * Final lacquer with 2 coats of 2-component topcoat, solid color RAL 3002 Carmine Red, compliant with the RAL 841GL system * Rear section metallized and painted RAL 9010 (Pure White) Including the following additional equipment: * 2-inch king pin * One galvanized steel front wall, approx. 400 mm high * One spare wheel holder in front of the front wall * Yellow-red air couplings mounted on the galvanized connection rail at the front * Bracket for beacon light at the rear of the trailer * Galvanized supports under the loading platform’s rear bevel * Super Grip 2 rubber coating

Condition: new, overall weight: 47,000 kg, axle configuration: 2 axles, Year of construction: 2026, Technical data MAX510-Z-2H-ATX-A-6.85-PA Speed: 80 km/h Total weight: 47,000 kg Fifth wheel load: 23,000 kg Axle load: 24,000 kg Gooseneck length: 3,750 mm Fifth wheel height loaded: 1,200 mm Steering radius to the rear: 2,300 mm Loading area length: 6,850 mm Extendable by: 5,500 mm Loading height with max. load: 350 mm Chassis length: 2,600 mm Loading height of rear chassis with max. load approx: 1,005 mm Suspension travel: -150/+450 mm Axle spacing: 1,360 mm Total width: 2,540 mm Total weight depends on fifth wheel load. Low bed: Low bed with external supports in extendable design "SUPER LOW" design, length approx. 6,850 mm. Low bed with solid hardwood floor approx. 40 mm thick and mechanical locking. The supply lines are protected in the extendable supports and automatically adjust to the respective low bed length. 5 pairs of lashing rings that can be folded outwards (LC 10,000 daN). 6 pairs of threaded blocks on the inner support for mounting screwable RUD rings. Rear chassis: Rear chassis with closed outer frame, checker plate covering and continuous prism excavator trough approx. 1,250/700 x 505 mm, open at the rear. Rodpeizu Nwjfx Ag Ueu 2 pairs of lashing rings that can be folded outwards (LC 10,000 daN). 1 pair of tension rings lying in the trough (LC 8,000 daN+5,300 daN). 2 pairs of stake pockets for 100 x 50 mm stakes in the outer frame Gooseneck: Gooseneck in SNT design to optimize the loading area length, length approx. 3,785 mm. Gooseneck can be raised/lowered hydraulically and removed. Technical fifth wheel load: 23,000 kg For tractor units: 4 x 2, 6 x 2 and 6 x 4 PENDEL-AXLE: "PENDEL-AXLE", all axles hydro-mechanically forcedly steered. Hose rupture valve on the axle compensation cylinder with automatic RESET function. Hydraulic cylinder with shut-off valves and pins for securing in raised position. Final painting of the axles with 2 layers of 2-component paint in a single color in "FAY-Gray-34-0260". Technical axle load: 12,000 kg Hydraulic axle compensation. Axle tool. Braking system: Braking system in accordance with EU regulations with EBS-E (2S2M) without connecting cables to the tractor unit. Electrical system: Electrical system in accordance with EU regulations, lighting 24 volts ASPÖCK-NORDIK (ASS3) ASPÖCK-UNIBOX on the front connection strip with 24N, 24S & 15-pin sockets. Connection in accordance with ISO. 24N ISO-1185 24S ISO-3731 15-pin ISO-12098 Steel construction: Steel construction made of high-strength fine-grain steels. Steel qualities: S355J2+N/S355MC (yield strength 355MPa) S690QL/S700MC (yield strength 690MPa) Paint: First-class and long-lasting corrosion protection of the standard shot-blasted welded frame guaranteed by a 2-component (2K) zinc dust primer. A high-quality 2-component (2K) top coat in a single color in RAL colors of your choice. Rear section metallized and painted in RAL 9010 (pure white). No metallic paint possible. Tires: Tires 245/70 R 17.5 3PMSF At the manufacturer's discretion. Load index (146/146F) Preparation for screw-on container positioning for 1x 20' or 1x 40' container on the outer supports. Without container locks. i i2" kingpins iA galvanized steel bulkhead, approx. 400 mm high. iA spare wheel with holder in front of the bulkhead. i2 brake shoes with holder on the bulkhead. iYellow-red air couplings on the galvanized connection strip at the front. Steering from the front and rear can be operated using a cable remote control via push buttons, with alignment control of the axles. (without insta

Condition: new, maximum load weight: 36,156 kg, overall weight: 45,000 kg, axle configuration: 3 axles, Year of construction: 2026, MAX200-N-3A-13.60-19.5-2.54 Technical data Speed: 80 km/h Total weight: 45,000 kg Fifth wheel load: 18,000 kg Rodpfx Agsg Sk Tve Ueu Axle load: 27,000 kg Empty weight (+/- 3%): 8,844 kg Payload approx.: 36,156 kg Loading area length: 13,600 mm Fifth wheel height loaded: 950->1,050 mm Rear steering radius: 2,300 mm Extendable by: 3,400 mm Axle spacing: 1,360/1,405 mm Total width: 2,540 mm Technical description Loading area: Loading area in extendable design with pneumatically operated locking. 2 pairs of lashing rings (LC 5,000 daN). 1 pair of lashing rings (LC 10,000 daN). 6 pairs of lashing rings that can be folded outwards (LC 5,000 daN). 2 pairs of lashing rings that can be folded outwards (LC 10,000 daN). Cut-outs in the outer frame of the loading area for hanging tensioning straps. (LC 2000 da N) Seat supports: JOST seat supports (mechanical) with 2-speed gearbox for 24t lifting load (50t test load). Axles: SAF axles: SAF axles CD, air-sprung, with disc brakes (377 mm), with lifting/lowering function. (ET 120). The self-steering axles with electro-magnetic reversing lock can be activated via reverse gear or manually. Axle tool. (± 80kg) Braking system: Braking system in accordance with EU regulations with EBS-E (2S2M) without connecting lines to the tractor unit. Steel construction: Steel construction made of high-strength fine-grain steels. Steel qualities: S355J2+N/S355MC (yield strength 355MPa) S690QL/S700MC (yield strength 690MPa) Paintwork: First-class and long-lasting corrosion protection of the standard shot-blasted welded frame guaranteed by a 2-component (2K) zinc dust primer. A high-quality 2-component (2K) top coat in a single color in RAL colors of your choice. Rear section metallized and painted in RAL 9010 (pure white). No metallic paint possible. Electrical system: Electrical system in accordance with EU regulations, lighting LED 24 Volt ASPÖCK-NORDIK (ASS3) ASPÖCK-UNIBOX on the front connection panel with sockets 24N, 24S & 15-pin. Connection in accordance with ISO. 24N ISO-1185 24S ISO-3731 15-pin ISO-12098 Accessories included Yellow-red air couplings on the galvanized front connection panel. 2 pieces of brake shoes with holder. 2" kingpin A galvanized steel bulkhead approx. 2200 mm high. (± 105kg) EN12642-XL Yellow reflector tape in accordance with EU regulations on the side, on the extension and at the rear of the trailer. European reflector signs (red-yellow) on the rear of the trailer. Loading area with approx. 38 mm thick hardwood floor. (± 320kg) 10 pairs of stake pockets for 100 x 50 mm stakes in the outer frame of the loading area. (± 30kg) 1 spare wheel holder under the loading area on the right in the direction of travel. Tires 435/50 R 19.5 as selected by the manufacturer. A mud flap ( ) on the rear of the trailer. Manual and description on USB stick. A bracket for a rotating beacon on the rear of the trailer. One bracket for a rotating beacon on the gooseneck and on the rear panel on the left and right the warning signs including a socket. An INOX toolbox across the loading area. (1000x400x2500) (± 135kg) 6 pairs of WADER container pockets in the loading area, for 1x20' container, 2 x 20' container or 1 x 40' container, an additional locking point is provided in the pull-out for a 45' container. (± 90kg) 4 pairs of WADER container locks. (± 60kg) 10 pairs of galvanized plug-in stanchions approx. 100 x 50 mm, 1,000 mm high. (± 220kg) 3 pairs of stanchion pocket strips, mounted across the loading area, for plug-in stanchion

Condition: new, maximum load weight: 44,000 kg, overall weight: 61,000 kg, axle configuration: 3 axles, Year of construction: 2026, Further information here: Rsdev D Abtepfx Ag Uou