Used Fliegl Tps 180 for sale (6,336)

Condition: new, machine/vehicle number: 8e6cf81e11b107f23f22f209a, axle configuration: 3 axles, tire size: 435/50 r19.5, Further information Fine-grained steel welded construction, with preload slight pretension in the neck area, saddle plate with replaceable 2 , kingpin, outer frame slightly inclined new design with Load-Lock profile for tensioning strap attachment, 24 to. 2-speed support winch, single-sided operation, with straight lower section, without thrust compensation Itjdpoi Ri E Hofx Akxjf Note: Free support leg corner dimension or free swing-through radius to the rear approx. 1930 mm, pull-out ladder at the rear, lateral door stop, 2 wheel chocks with holder, aluminium side collision protection, galvanized steel underride guard, quarter-shell mudguards in front of 1st axle and behind each axle, with anti-spray flaps according to EC, impact protection at the rear SAF disc brake axles, laser-measured axle/chassis to reduce tire wear and fuel consumption, air suspension 2-line compressed air brake system, colored cable routing for easy servicing, spring-loaded parking brake, 2 swap-proof coupling heads at the front, without connecting cable, EBS, electronic brake system with EBS socket at the front, without connecting cable, Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS, with lift & lower valve, vehicle stability system 435/50 R19.5 tires of the manufacturer's choice, steel rims, factory silver 24 volt, multi-chamber lights, amber LED lighting at the sides, 2 white position lights at the front, 2 white/red lane departure lights at the rear, 2 x 7-pin interchangeable sockets at the front, without connecting cable Floor: Screen printing plates approx. 30 mm thick, on longitudinal beams for high point load capacity for forklift axle load up to max. 7100 kg Front bulkhead / corner stanchions: 2,580 mm high, steel corner stanchions in volume design, release device for side tarpaulin on bulkhead, crash blocker, bottom inside at approx. 140 mm height with steel impact protection Center stanchions: 3 pairs of sliding stanchions can be moved along the entire length, with 4 insertion pockets and a long pocket at the bottom, 3 pairs of stanchion positions Insertion slats: 5 rows of wooden insertion slats Rear wall / rear corner stanchions: Rear steel corner stanchions up to the lower edge of the roof, attachment for tarpaulin with round tube and tarpaulin tensioning ratchet, rear portal doors, 2-leaf with 2 internal espagnolette locks each Tarpaulin: Tarpaulin with welded-in horizontal and vertical straps, stainless steel tensioning fasteners Roof: Sliding roof, rear end lift can be folded up, with roof can be pushed from rear to front, L-shaped roof rail for car industry, internal width between the roof rails, approx. 2 490 mm, tarpaulin color: white, 400 Roof non-elastic, hardly any deflection of the roof rail when loading and unloading, optimum rain strip at the rear, at the top of the end bows, above the doors, EcoLift - lifting roof can be raised by approx. 380 mm, with gas pressure damper support, 3 driving positions at the front: interior height at the front approx. 2900 mm/ 2950 mm / 3000 mm, adjusted to approx. 3000 mm Germany, test approval according to EC 2007/46, 24/7 service hotline, Fliegl manufacturer's certificate for structural strength according to EN 12642 XL, prepared for single-line license plate holder, warning sign according to ECE - 70, reflective strips: white, continuous on the side tarpaulin at the bottom and at the top in the corners (if visible drop sides, then the strip at the bottom, on

Condition: new, machine/vehicle number: f044065451f6d849ee7a5b9f8, empty load weight: 5 kg, maximum load weight: 29 kg, overall weight: 35 kg, axle configuration: 3 axles, tire size: 385 / 65 r 22,5, Further information Chassis semi-trailer forwarding Welded steel construction in reinforced design, only 2 side members as double T-beams with steel/checker plate between the side members, saddle plate with replaceable 2 kingpins. Protective plate for rear lights. 1 steel storage box, recessed between side members 8 pairs of lashing eyes bolted or welded to the frame at the manufacturer's choice 24 t. 2-speed support winch, single-sided operation, with straight lower section, without thrust compensation 2 wheel chocks with holder Aluminium side bumper Galvanized steel underride guard Half-shell mudguards with anti-spray flaps according to EC 1 spare wheel holder for 1 e-wheel, with wheel fastening set 8 wooden stanchions of the manufacturer's choice, bolted to frame with 2 wooden stanchions each, telescopic from 1800 to 2800 mm, per pair 7 to. Axles + suspension SAF disk brake axles with 430 mm disk diameter Air suspension with lifting & lowering valve, safety cable on the axles 1st axle automatic lift axle, including forced lowering and starting aid, actuation of 3x brakes (starting aid is functional up to an axle load excess of 30% and up to a speed of max. 25 km/h) Axle spacing offset mm (combined transport) up to 44 tons gross train weight Wheels and tires 385 / 65 R 22,5 at the manufacturer's discretion Steel rims, factory silver Brake system 2-line compressed air brake system Spring-applied parking brake Axle load detection via EBS-Canbus signal, for indication via display in the cab, truck must be prepared accordingly, no truck installed (no calibrated scales) 2 swap-proof coupling heads at the front, without connecting cable EBS, electronic brake system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red lane departure lights at the rear 2 x 7-pin and 1 x 15-pin interchangeable sockets at the front, without connecting cable Front bulkhead/front stanchions Steel/grid bulkhead, approx. 2,300 mm high, bolted to the frame Approval / plates Country of approval: Germany Approval according to EC 2007/46 Prepared for single-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white at the sides and red at the rear Paint finish Frame DB 7350 nova gray Itsdpfxoi Rivwo Akxof Black coated support legs Front wall hot-dip galvanized Attention: Archive pictures!

Condition: new, machine/vehicle number: bdf30cb8a53c70e900bdb40a7, empty load weight: 2 kg, maximum load weight: 9 kg, overall weight: 11 kg, axle configuration: 2 axles, tire size: -, Further information Chassis central axle tipping trailer Welded steel construction, continuous tipping shaft at the rear with 80 mm ball tipping bearing Gearbox support foot at the front 2 wheel chocks with holder Steel underride guard Rear splash guards across the entire width Quarter-shell mudguards Lockable storage space for access ramps underneath the loading area Towing device central axle trailer Tow bar with tested 40 mm towing eye Height-adjustable drawbar via spindle, max. adjustment range 300 mm Axles + suspension BPW drum brake axles Axle/chassis laser-measured Reduction in tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load compensation (rocker compensation) Wheels and tires 235 / 75 R 17,5 manufacturer's choice Factory silver steel rims Brake system 2-line compressed air brake systemColor-coded cable routing for easy servicing. Hand spindle parking brake Integral air reservoir ABS and ALB, with ABS plug at the front, with connecting cable, Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! 2 swap-proof coupling heads at the front, with connecting cables to the motor vehicle, Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red lane departure lights at the rear 2 x 7-pin non-interchangeable plugs at the front, with connecting cable, Hydraulics Three-way tipping mechanism, hydraulic multi-piston press with lift limiter and safety cable, Low-pressure cylinder up to max. 170 bar, without throttle. If necessary, this must be retrofitted to the truck. Hydraulic connection with SVK plug NW 10/3, incl. connection hose Hydraulic actuation via truck power take-off Tilting bridges Sturdy tipper body with 4 mm sheet steel floor, steel side wall structure, continuous side walls, hinged and pivoted with central locking at the bottom. Rear corner stanchions pluggable. Rear wall can be folded down and pivoted, with central locking at the bottom. Platform length approx. 4,500 mm, side walls with 5 hinges at the bottom. Platform width 2420 mm 5 pairs of lashing eyes in the floor, 5 tons each Operating instructions The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. (Poor driving and trailing behavior possible due to incorrect load distribution) Ijdpfx Aji Riwiekxotf Country of registration / plates Country of registration: Germany with Dekra approval and expert opinion (according to §13 EG - FGV) 24/7 service hotline Prepared for single-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white at the sides and red at the rear Paintwork Hot-dip galvanized frame incl. passivation 15-year warranty against rusting through Dropside/bridge RAL 3002 carmine red Rear support, access ramps, storage box are optionally available at extra cost Attention: Archive pictures

Condition: new, machine/vehicle number: 068983c41e44eb5660fa9100c, empty load weight: 6 kg, maximum load weight: 28 kg, overall weight: 35 kg, axle configuration: 3 axles, tire size: 435/50 r19,5, Further information Chassis saddle forwarding Fine-grained steel welded construction, with preload slight pre-tensioning in the neck area, saddle plate with replaceable 2 kingpins X-tra Long, with 15030 mm internal length Outer frame slightly inclined new design with Load-Lock profile for tensioning strap attachment 24 to. 2-speed support winch, single-sided operation, with straight lower section, without thrust compensation Note: Free support leg corner dimension or free swing-through radius to the rear approx. 1930 mm Extension ladder at the rear Door retainer at the side 2 wheel chocks with holder Aluminium side bumper Galvanized steel underride guard Quarter-shell mudguards in front of 1st axle and behind each axle Impact protection at the rear Axles + suspension SAF disc brake axles Axle/chassis laser-measured Reduction of tire wear and fuel consumption Air suspension Brake system 2-line compressed air brake system Colored line routing for easy service. Spring-loaded parking brake 2 interchangeable clutch heads at the front, without connecting cable EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lifting & lowering valve Vehicle stability system AAC Basic, automatic relief axle acting on last axle, as maneuvering aid, up to 20 km/h, can be switched off manually Axle load detection via EBS-Canbus signal, for indication via display in driver's cab, truck must be prepared accordingly, no truck installation (no calibrated scales) Wheels and tires 435/50 R19.5 tires of the manufacturer's choice Steel rims, factory silver Electrical system 24 volt, multi-chamber lights, amber LED lighting on the side Side amber LED lighting coupled with the blinker Flashing side lights Side lights 2 white position lights at the front 2 white/red rear lane departure lights 2 x 7-pin interchangeable sockets at the front, without connecting cable Floor Screen printing plates approx. 30 mm thick, on longitudinal beams for high point load capacity for forklift axle load up to max. 7100 kg Front wall / front corner stanchions 2,580 mm high, steel corner stanchions in volume design, release device for side tarpaulin on bulkhead, crash blocker, bottom inside at approx. 140 mm height with steel impact protection Center stanchions 3 pairs of sliding stanchions can be moved along the entire length, with 4-fold pockets and with long pocket at the bottom. 3 pairs of stanchion positions Insertion slats 5 rows of wooden slats Rear wall / rear corner stanchions Rear corner stanchions steel up to lower edge of roof, attachment for tarpaulin with round tube and tarpaulin tensioning ratchet Rear portal doors, 2-leaf with 2 internal espagnolette locks each Tarpaulin Tarpaulin, with welded-in horizontal and vertical straps Stainless steel tension locks Roof Sliding roof, rear end lift can be folded up, with roof can be pushed from rear to front, L-shaped roof rail for automotive industry, internal width between the roof rails approx. 2,490 mm, tarpaulin color: white Roof non-elastic, hardly any deflection of the roof rail when loading and unloading EcoLift - lifting roof can be raised by approx. 380 mm, on both sides, with gas pressure damper support, 3 driving positions at the front: Front interior height approx. 2900 mm / 2950 mm / 3000 mm, Iedpfx Asi Riwuskxotf adjusted to approx. 3000 mm Optimum rain strip at the rear, at the top of the end bows,

Condition: new, machine/vehicle number: 628cde0fe99cc2d3c8eaa8dd8, overall weight: 24,000 kg, axle configuration: 3 axles, tire size: 235 / 75 r 17,5, Further information Chassis low loader trailer Welded steel construction Turntable with powerful ball bearing slewing ring Folding rear support 2 wheel chocks with holder Aluminum side bumpers Rear spray flaps across the entire width Half-shell mudguard 1st axle with anti-spray flapsAnti-spray flaps behind 2nd and 3rd axle 1 plastic tool box, with shelf, w=620/h=360/t=440 mm, lockable with a padlock. (lock not included in scope of delivery) Extensions extendable to 3,000 mm Storage compartment for wooden planks in the middle of the loading area Wooden planks 70 mm for widening to 3000 mm Low loader lashing eyes (40 lashing options) 1 pair of lashing cut-outs in the front side member on offset, 10 tons each 4 pairs of lashing holes in the outer frame, 5 tons each (lashing strap attachment) 7 pairs of lashing points at the top and sides of the outer frame, 10 tons each 1 x front on offset 6 x in the drop deck First lashing eye 250 mm from the front and last max. 250 mm from the rear, distance between lashing eyes not greater than 1100 mm 5 pairs of stake pockets embedded in the outer frame, inside 70 x 40 mm, (can be converted to 5 to. ring lashing eyes, not included in the scope of delivery) 2 additional pairs of hinged lashing eyes, 10 tons each 1 x on offset (protrudes) 1 x embedded in the floor behind the last axle Trailer drawbar Turntable Drawbar with tested 40 mm drawbar eye Axles + suspension Drum brake axles, at the manufacturer's choice Axle/chassis laser-measured Reduction of tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load compensation (rocker compensation) Wheels and tires 235 / 75 R 17,5 at the manufacturer's discretion Twin steel rims, factory silver Brake system 2-line compressed air brake system Spring-applied parking brake 2 non-interchangeable coupling heads at the front, with connecting cables to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cable Make: Wabco or Knorr Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red rear lane departure lights 2 x 7-pin interchangeable plugs at the front, with connecting cable, 1 LED rotating beacon with holder, switched via parking light (removable light) 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm Floor Front offset with steel/ checker plate covering Storage box recessed into the drive-over slope to the offset Then with 70 mm softwood floor, steel/ checker plate covering in the wheel arch area Rear slope with 70 mm softwood floor Isdpfx Aei Ri Ddjkxotf Deep loading area incl. rear slope 6,500 mm Drive-on ramps Steel ramps 2,800 mm long, 750 mm wide, can be moved sideways covered with wood with spring lift support Country of registration / plates Country of registration: Germany 24/7 service hotline Prepared for two-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white on the sides and red on the rear Warning sign according to ECE - 70 Paintwork Hot-dip galvanized frame incl. passivation 15-year warranty against rusting through Drawbar Galvanized or black, at the manufacturer's discretion Drive-on ramps Hot-dip galvanized Attention! These are archive pictures!

Condition: new, machine/vehicle number: abc6276e1749f9dddc494eb32, empty load weight: 4,900 kg, maximum load weight: 30,100 kg, overall weight: 35,000 kg, axle configuration: 3 axles, tire size: 385/65 r22,5², Further information Chassis tipper semi-trailer Fine-grained steel welded construction, lightweight design, fifth wheel plate with interchangeable 2 kingpins Curved front end Patented Telescopic support in the middle, unhitching with load not possible, when unhitched the vehicle must be at an angle to the rear. 2 wheel chocks with holder Folding underride guard Half-shell mudguards Integrated mudguard holder Stone-repellent surface with anti-spray flaps on last axle only 1 tarpaulin pole with bracket 2 towing hooks at the rear Axles+suspension SAF disc brake axles with 430 mm disc diameter Axle/chassis laser-measured Reduction in tire wear and fuel consumption Axles in off-road version, Air suspension 1st axle automatic lift axle, including forced lowering and starting aid, actuation of 3x brakes (starting aid is functional up to an axle load excess of 30% and up to a speed of max. 25 km/h) Hot-dip galvanized lift axle mechanism 10-year warranty against rusting through Brake system 2-line compressed air brake systemColor-coded cable routing for easy servicing. Spring-loaded parking brake 2 interchangeable front clutch heads, without connecting line EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lifting & lowering valve Vehicle stability system Automatic tilt lowering with shut-off valve Wheels and tires 385/65 R22.5 tires of the manufacturer's choice Steel rims, factory silver Electrical system 24 volt, multi-chamber lights, amber LED lighting at the sides 2 white position lights at the front 2 white/red rear lane departure lights 2 x 7-pin interchangeable sockets at the front, without connecting cable Hydraulics Low-pressure cylinder max. 170 bar, smallest stage hard-chlorinated, with HDK screw socket, fixed part, NW 48 mm (without hose connection). Hydraulic actuation via truck power take-off Troughs Iedei Ri H Ispfx Akxotf Aluminum box body made of high-quality, abrasion-resistant 5 mm thick front wall, with external walls made of 30 mm hollow chamber profiles, cleanly welded, with bulk material-repellent top rail profile. Inside with access to front wall (not in conjunction with Cramaro). Shovel and brush holder on the outside of the front wall. Greenline - conical and aerodynamic trough shape Membrane rear wall Rear wall as swing flap with double-jointed hinge, resting on the outside with double hook lock. Rear panel with rubber sealNote! Heat-resistant up to max. 170°C! Floor 6 mm thick throughout Standing platform with access, connection plate for air/electric and brake with large clearance for best possible operability. Roller tarpaulin on one side for depositing in FR-right, with central locking in FR-left Operating instructions For salt, lime, etc. We recommend a tipping cylinder with a hard chrome-plated piston rod so that it is not attacked by the material and rusts. The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. (Poor driving and trailing behavior possible due to incorrect load distribution) Country of registration / plates Germany Test approval according to EC 2007/46 24/7 service hotline Prepared for single-line license plate holder Contour marking with reflective strips according to ECE R 048, white on the sides and red on the rear

Condition: new, machine/vehicle number: 074630ca1b8dc2d710f82c15a, empty load weight: 3,980 kg, overall weight: 35,000 kg, axle configuration: 3 axles, tire size: 385/65 r22.5, Further information Chassis tipper semi-trailer Fine-grained steel welded construction, lightweight design, fifth wheel plate with interchangeable 2 kingpins Curved front end Patented Without support leg Wheel chocks with holder Underride guard, foldable Half-shell mudguards Integrated mudguard holder Stone-repellent surface Tow hook at the rear Axles+suspension SAF disc brake axles Axle/chassis laser-measured Reduction of tire wear and fuel consumption Air suspension 1st axle automatic lift axle, including forced lowering and starting aid, actuation of 3x brakes (starting aid is functional up to an axle load excess of 30% and up to a speed of max. 25 km/h) Iedpfsi Ri H Sex Akxetf Hot-dip galvanized lift axle mechanism 10-year warranty against rusting through Brake system 2-line compressed air brake systemColor-coded cable routing for easy servicing. Spring-loaded parking brake 2 interchangeable front clutch heads, without connecting line EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lifting & lowering valve Vehicle stability system Wheels and tires 385/65 R22.5 tires of the manufacturer's choice Polished aluminum rims, manufacturer's choice Electrical system 24 volt, multi-chamber lights, amber LED lighting at the sides 2 white position lights at the front 2 white/red rear lane departure lights 2 x 7-pin socket at the front, without connecting cable Hydraulics Low-pressure cylinder max. 170 bar, smallest stage hard-chlorinated, with HDK screw socket, fixed part, NW 48 mm (without hose connection). Hydraulic actuation via truck power take-off Troughs Aluminum box body made of high-quality, abrasion-resistant 5 mm thick front wall, with external walls made of 30 mm hollow chamber profiles, cleanly welded, with bulk material-repellent top rail profile. Inside with access to front wall (not in conjunction with Cramaro). Shovel and brush holder on the outside of the front wall. Greenline - conical and aerodynamic trough shape Membrane rear wall Rear wall as swing flap with double-jointed hinge, resting on the outside with double hook lock. Rear panel with rubber sealNote! Heat-resistant up to max. 170°C! Floor 5 mm thick throughout, Brinell 110Note! Only for transporting sand, grit and rolled gravel with a maximum grain size of up to 20 mm! All other transport goods are excluded from the warranty! Standing platform with step, connection plate for air/electric and brake with large clearance for best possible operability. Roller tarpaulin on one side for depositing in FR-right, with central locking in FR-left Operating instructions For salt, lime, etc. We recommend a tipping cylinder with a hard chrome-plated piston rod so that it is not attacked by the material and rusts. The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. (Poor driving and castering behavior possible due to incorrect load distribution) Revolution Link: Revolution Link experience report: Country of registration / plates Germany with Dekra approval and expert opinion (according to §13 EG - FGV) 24/7 service hotline Prepared for single-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white at the sides and red at the rear Paint finish Frame DB 7350 nova gray Body R

Condition: new, machine/vehicle number: 45d76d32267904923b7adcdea, empty load weight: 4,980 kg, maximum load weight: 30,020 kg, overall weight: 35,000 kg, axle configuration: 3 axles, tire size: 385/65 r22.5, Further information Chassis tipper semi-trailer Fine-grained steel welded construction, lightweight design, fifth wheel plate with interchangeable 2 kingpins Curved front end Patented 24 t. 2-speed support winch, single-side operation, with straight lower section, without thrust compensation Wheel chocks with holder Underride guard, folding Half-shell mudguards Integrated mudguard holder Surface stone-repellent Tow hook at the rear Axles+suspension SAF disc brake axles Axle/chassis laser-measured Reduction of tire wear and fuel consumption Air suspension 1st axle automatic lift axle, including forced lowering and starting aid, actuation of 3x brakes (starting aid is functional up to an axle load excess of 30% and up to a speed of max. 25 km/h) Hot-dip galvanized lift axle mechanism 10-year warranty against rusting through Brake system 2-line compressed air brake systemColor-coded cable routing for easy servicing. Spring-loaded parking brake 2 interchangeable front clutch heads, without connecting line Itsdpfx Akei Ri Idoxsf EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lifting & lowering valve Vehicle stability system Wheels and tires 385/65 R22.5 tires of the manufacturer's choice Polished aluminum rims, manufacturer's choice Electrical system 24 volt, multi-chamber lights, amber LED lighting at the sides 2 white position lights at the front 2 white/red rear lane departure lights 2 x 7-pin socket at the front, without connecting cable Hydraulics Low-pressure cylinder max. 170 bar, smallest stage hard-chlorinated, with HDK screw socket, fixed part, NW 48 mm (without hose connection). Hydraulic actuation via truck power take-off Troughs Aluminum box body made of high-quality, abrasion-resistant 5 mm thick front wall, with external walls made of 30 mm hollow chamber profiles, cleanly welded, with bulk material-repellent top rail profile. Inside with access to front wall (not in conjunction with Cramaro). Shovel and brush holder on the outside of the front wall. Greenline - conical and aerodynamic trough shape Membrane rear wall Rear wall as swing flap with double-jointed hinge, resting on the outside with double hook lock. Rear panel with rubber sealNote! Heat-resistant up to max. 170°C! Floor 5 mm thick throughout, Brinell 110Note! Only for transporting sand, grit and rolled gravel with a maximum grain size of up to 20 mm! All other transport goods are excluded from the warranty! Standing platform with step, connection plate for air/electric and brake with large clearance for best possible operability. Roller tarpaulin on one side for depositing in FR-right, with central locking in FR-left Operating instructions For salt, lime, etc. We recommend a tipping cylinder with a hard chrome-plated piston rod so that it is not attacked by the material and rusts. The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. (Poor driving and castering behavior possible due to incorrect load distribution) Revolution Link: Revolution Link experience report: Country of registration / plates Germany with Dekra approval and expert opinion (according to §13 EG - FGV) 24/7 service hotline Prepared for single-line license plate holder Contour marking with reflective strips according to ECE R 0

Condition: new, machine/vehicle number: 55d3c5c03e032385649769b1b, empty load weight: 9,900 kg, maximum load weight: 14,100 kg, overall weight: 24,000 kg, axle configuration: > 3 axles, tire size: 235 / 75 r 17,5, Further information Chassis low loader trailer Welded steel construction Turntable with strong ball bearing slewing ring, storage box recessed in Incl. Turntable front end Folding rear support 2 wheel chocks with holder Aluminum side bumper Rear spray flaps across the entire width Widenings extendable to 3,000 mm (not in rear slope) (However, the track width of the construction machinery or vehicles to be transported must not exceed the outer frame width of 2,550 mm) Storage compartment for wooden planks in the middle of the cargo bed Wooden planks 70 mm for widening to 3000 mm Low loader lashing eyes 3 pairs of lashing points, 10 tons each, integrated in the floor at the front 6 pairs of lashing points at the top and sides, each 10 tons, integrated in the outer frame 1 x to the neck area remaining distributed in between Spacing not greater than 1200 mm 1 x rear slope 5 pairs of stake pockets embedded in the outer frame, inside 70 x 40 mm, (can be converted to 5 to. ring lashing eyes, not included in the scope of delivery) Towing equipment Trailer turntable Drawbar with tested 40 mm towing eye Please note! With 40 mm drawbar eye, the maximum permissible total weight of the truck is 18000 kg, otherwise 50 mm drawbar eye required. Axles + suspension SAF drum brake axles Axle/chassis laser-measured Reduction in tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load compensation front and rear (rocker compensation) Wheels and tires 235 / 75 R 17,5 at the manufacturer's choice Twin steel rims, factory silver Brake system 2-line compressed air brake system Spring-applied parking brake 2 non-interchangeable coupling heads at the front, with connecting cables to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cable Ijdei Ri I Eopfx Akxetf Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red lane departure lights at the rear 2 x 7-pin interchangeable plugs at the front, with connecting cable, 1 LED rotating beacon with holder, switched via parking light (removable light) 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm Floor Front area steel floor, then with 70 mm softwood floor, steel/checker plate flooring in the wheel housing area Rear slope with 70 mm softwood floor Drive-on ramps Steel ramps 2,800 mm long, 750 mm wide, can be moved sideways covered with wood with spring jack support Operating instructions With an axle load of 10,000 kg, a special permit is required, only indivisible loads possible!!! The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. (Poor driving and trailing behavior possible due to incorrect load distribution) Country of registration / plates Country of registration: Germany 1 with Dekra approval and expert opinion (according to §13 EG - FGV) 24/7 service hotline Prepared for two-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white at the sides and red at the rear Paint finish Frame Ral 3002 carmine red 10-year warranty against rusting through Drawbar Galvanized or black, at the manufacturer's choice Drive-on ramps Hot-dip galvanized Attention: Archive pictures!

Condition: new, machine/vehicle number: 8df1ead53cc82aeb51e50a37d, empty load weight: 4 kg, maximum load weight: 13,880 kg, overall weight: 18 kg, axle configuration: 2 axles, tire size: 235 / 75 r 17,5, Further information Chassis Turntable Disposal Fine-grained steel welded construction Container locking system: - 2 pairs of locking hooks embedded in the floor - Pneumatic actuation The container locking mechanism is a 2-point design, acting from the inside, and locking of roll-off containers with an inner web is not possible (for transporting roll-off containers with a sub-frame in accordance with DIN 30722) Note! At the start of the roller recess at the front, the container must be pushed on completely flat! Longitudinal guide rails can be moved sideways and removed, rails approx. 115 mm high Turntable with strong ball bearing slewing ring 8 pairs of lashing mushrooms at the top and sides of the outer frame, 5 tons each 7 pairs of stake pockets embedded in the outer frame, inside 70 x 40 mm, (can be converted to 5 to. ring lashing eyes, not included) 2 wheel chocks with holder Aluminum side bumpers Steel underride guard Quarter-shell mudguards according to EG with anti-spray flaps according to EG Towing equipment Trailer turntable Drawbar with tested 40 mm drawbar eye Axles + suspension SAF drum brake axles Axle/chassis laser-measured Reduction of tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearings Wheels and tires 235 / 75 R 17,5 at the manufacturer's choice Twin steel rims, factory silver Brake system 2-line compressed air brake system Spring-applied parking brake 2 non-interchangeable coupling heads at the front, with connecting cables to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red lane departure lights at the rear 2 x 7-pin interchangeable plugs at the front, with connecting cable, floor Steel floor Roller recess for container recessed in the floor at the frontfor roll-off containers from 5,000 - 7,000 mm in length Note: Slight floor undulation possible due to welding distortion! Drive-on ramps Lockable storage space for loading ramps underneath the loading area Operating instructions A special permit is required for axle loads of 10,000 kg. Approval must be applied for individually in each federal state; the legislator does not have to grant approval for 20 t GG. Customer risk. The specified total weight is technically possible; depending on the load, the total weight may not be achieved while complying with the permissible axle/support and fifth-wheel loads. (Poor driving and trailing behavior possible due to incorrect load distribution) Country of registration / plates Country of registration: Germany Iodpfx Akoi Ri Nusxotf with Dekra approval and expert opinion (according to §13 EG - FGV) 24/7 service hotline Prepared for single-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white at the sides and red at the rear Warning sign according to ECE - 70 Paint finish Frame DB 7350 nova gray 15-year warranty against rusting through Note: Bottom corrugation possible due to hot-dip galvanizing! Drawbar KTL black Attention: Archive pictures!

Condition: new, machine/vehicle number: 6d88bda3a1ee2464a81b34f36, empty load weight: 4 kg, maximum load weight: 13 kg, overall weight: 18 kg, axle configuration: 2 axles, tire size: 235 / 75 r 17,5, Further information Chassis low loader trailer Welded steel construction, with slight pretensioning in the middle, turntable with strong ball bearing slewing ring, wheel chocks with holder, quarter-shell mudguards in front of and behind each axle Low loader lashing eyes over front axle: 2 pairs of ring lashing eyes, 5 tons each at the front on offset Lowbed: 4 pairs of lashing eyes on the side of the low bed, 6 tons each 5 pairs of lashing eyes per 5 tons between the side members Trailer drawbar Turntable Drawbar with tested 40 mm drawbar eye, mechanically adjustable in length by 6 x 100 mm and lockable (drawbar length 1 700 - 2 300 mm) Axles + suspension BPW drum brake axles, each with an axle load of 10 tons, axle adjuster. Axle endurance brake test to 105 km/h, rear axle can be removed manually. By releasing the air lock and lowering the rear to the ground. Then disconnect the connecting hoses from the rear section, insert the transport bar into one of the rear sockets and unhook the rear by gently pushing it down at the rear and pulling it back at the same time (parking brake released). After loading or unloading, drive up to the rear section and hook it in up to the mark. Then lift the rear section up to driving height and attach the connecting hoses. Confirm the pin lock. (Visually check whether the bolt engages) and check the rear function. Air suspension with lift & lower valve Wheels and tires 235 / 75 R 17.5, from leading manufacturers, steel rims in twin arrangement, factory silver Brake system 2-line compressed air brake system, spring-loaded parking brake, 2 interchangeable clutch heads at the front, with connecting lines to the motor vehicle, EBS, electronic brake system with EBS plug at the front, with connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side, 2 white position lights at the front, 2 white/red lane departure lights at the rear, rotating beacon with holder, switched via parking light (light can be removed), 2 pairs of warning signs, double LED illuminated and extendable to 3,300 mm, removable with plug, 2 x 7-pin interchangeable plugs at the front, with connecting cable, 1 x 7-pin agricultural plug, voltage converter 12/24 volt (only for electrics, not for ABS/EBS) Floor Steel/ checker plate floor on offset, between longitudinal and cross member with perforated plate cover. Axle cover cannot be driven over, widening to 3000 or 3300 mm possible. Operating instructions Ijdpfx Akoi Ri N Aexotf Please note! A special permit is required for axle loads of 10,000 kg. The permit must be applied for individually in each federal state; the legislator does not have to give an approval for 20 tons GG. Customer risk. Special approval required if the overall length of the train exceeds 18 750 mm. Observe country-specific approval regulations. The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. Observe the BO circle!!! Approval / plates Country of registration: Germany, with Dekra approval and expert opinion (according to §13 EG - FGV), prepared for single-line license plate holder, warning sign according to ECE - 70, contour marking with reflective strips according to ECE R 048 Paintwork Front frame hot-dip galvanized incl. passivation, rear frame RAL9006 silver, drawbar KTL bla

Condition: new, machine/vehicle number: f8fb99947a1c19bc4d63549ff, empty load weight: 6 kg, maximum load weight: 17 kg, overall weight: 24 kg, axle configuration: 3 axles, tire size: 235 / 75 r 17,5, Further information Chassis low loader trailer Welded steel construction Turntable with powerful ball bearing slewing ring Folding rear support 2 wheel chocks with holder Aluminum side bumpers Rear spray flaps across the entire width Iodpfxji Riwfe Akxstf Half-shell mudguard 1st axle with anti-spray flapsAnti-spray flaps behind 2nd and 3rd axle 1 plastic tool box, with shelf, w=620/h=360/t=440 mm, lockable with a padlock. (lock not included in scope of delivery) Widenings extendable to 3,000 mm (not in rear slope) (track width of the construction machinery or vehicles to be transported must not exceed the outer frame width of 2,550 mm) Storage compartment for wooden planks in the middle of the cargo bed Wooden planks 70 mm for widening to 3000 mm Low loader lashing eyes 1 pair of front lashing eyes recessed on offset, 5 tons each 7 pairs of lashing rings at the top and sides of the outer frame, 10 tons each 1 x front on offset 6 x in the drop deck First lashing eye 250 mm from the front and last max. 250 mm from the rear, distance between lashing eyes not greater than 1100 mm 5 pairs of stake pockets embedded in the outer frame, inside 70 x 40 mm, (can be converted to 5 to. ring lashing eyes, not included in the scope of delivery) 2 additional pairs of hinged lashing eyes, 10 tons each 1 x on offset (protrudes) 1 x embedded in the floor behind the last axle Trailer drawbar Turntable Drawbar with tested 40 mm drawbar eye Axles + suspension SAF drum brake axles Axle/chassis laser-measured Reduction of tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load compensation (rocker compensation) Wheels and tires 235 / 75 R 17,5 at the manufacturer's discretion with M&S marking Twin steel rims, factory silver Brake system 2-line compressed air brake system Spring-applied parking brake 2 non-interchangeable clutch heads at the front, with connecting lines to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cable Make: Wabco or Knorr Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red lane departure lights at the rear 2 x 7-pin interchangeable plugs at the front, with connecting cable, 1 LED rotating beacon with holder, switched via parking light (removable light) 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm Floor Front offset with steel/ checker plate covering Storage box recessed into the drive-over slope to the offset Then with 70 mm softwood floor, steel/ checker plate covering in the wheel arch area Rear slope with 70 mm softwood floor Deep loading area incl. rear slope 6,500 mm Drive-on ramps Steel ramps 2,800 mm long, 750 mm wide, can be moved sideways Additional ramp safety device hinged at the bottom (to prevent the ramps from slipping sideways, not in conjunction with hydraulic side ramp displacement) covered with wood with spring lift support Operating instructions With an axle load of 10,000 kg, a special permit is required, only indivisible loads possible!!! The specified total weight is technically possible; depending on the load, the total weight may not be achieved while complying with the permissible axle/support and fifth-wheel loads. (Poor driving and trailing behavior possible due to incorrect load distribution) Country of registration / plates Coun

Condition: new, machine/vehicle number: f80f2330e1318ef03bc20755e, empty load weight: 3,200 kg, maximum load weight: 35,800 kg, overall weight: 39,000 kg, axle configuration: 3 axles, tire size: 385/65 r22.5, Further information Fine-grained steel welded construction in lightweight design, saddle plate with replaceable 2 kingpins, only 2 longitudinal beams as double T-beams for retrofitting connecting gallows at the front in new/current design, outer frame slightly slanted with load-lock profile for attaching tension beltsNote! to attach the belts in conjunction with drop sides, the drop sides must be opened! 24 t. 2-speed support winch, single-sided operation, with straight lower section, without thrust compensation, wheel chocks with holder, aluminium side bumper, foldable, galvanized steel underride guard, extendable, half-shell mudguards!!! enclosed loose, not mounted!!!, with anti-spray flaps behind each axle, 1 plastic water barrel, capacity approx. 30l, in FR left BPW disc brake axles with 430 mm disc diameter, axle/chassis laser-measured Reduction of tire wear and fuel consumption, air suspension, 1st axle automatic lift axle, can also be lowered manually, can be operated with a hand button on the vehicle 2-line compressed air brake system, with 1 air reservoir central standard, spring-loaded parking brake, 2 interchangeable coupling heads at the front, without connecting cable, EBS, electronic brake system with EBS socket at the front, without connecting cable, EBS 2S/2M, test connection for brake cylinder pressure on the EBS module laid to the outside, Attention: The trailer vehicle may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lifting & lowering valve, control unit + brake integrated in frame as with tipper semi-trailer, mounted in front of the axles Brake pad wear indicator for disc brakes via ABS/EBS lamp Truck 385/65 R22.5 Continental tires, steel rims, factory silver 24 volt, multi-chamber lights, amber LED lighting at the side as for tipper semi-trailer, dimension 3000 mm must be observed, 2 white LED position lights at the front, loose, 2 white/red lane departure lights at the rear, 2 x 7-pin interchangeable sockets at the front, without connecting cable Isdei Riwqjpfx Akxstf Germany, test approval according to EC 2007/46 for complete vehicle, 24/7 service hotline, prepared for double license plate holder single-line1 x plastic and 1 x stainless steel interchangeable holder Warning sign according to ECE - 70, aluminum, loose, EBS, safe parking, without contour marking / reflective strips according to ECE R 048, Frame: DB 7350 nova gray, support legs: black coated Available immediately!

Condition: new, machine/vehicle number: e7fbe178b85a202cade7e95af, empty load weight: 5 kg, maximum load weight: 22 kg, overall weight: 29 kg, axle configuration: 2 axles, tire size: 235 / 75 r 17,5, Further information Chassis saddle forwarding Welded fine-grained steel construction, saddle plate with replaceable 2 king pins, with 2 king pin positions Slightly angled outer frame with load-lock profile for attaching lashing strapsNote! To attach the straps in conjunction with drop sides, the drop sides must be opened! 2 pairs of lashing eyes embedded in the outer frame on gooseneck, 5 tons each 8 pairs of lashing eyes embedded in the outer frame in the low bed, 5 tons each 24 to. 2-speed support winch, single-side operation, with straight lower section, without thrust compensation 2 wheel chocks with holder Aluminum side bumper Steel underride guard Quarter-shell mudguards in front of and behind axle unit 2 Stainless steel stowage box, w=600/h=400/t=500 mm, with polished door, lockable 2 pairs of stake pockets recessed in the outer frame on gooseneck, 70 x 40 mm internal dimensions 6 pairs of stanchion pockets in the outer frame recessed in the deep bed, 70 x 40 mm Internal dimension!!! Internal width between the stanchions 2420 mm!!! 3 lashing/stanchion rails in the drop-down bed, embedded transversely in the floor across the entire width up to the outer frame (max. usable internal width between the outer stanchions approx. 2170 mm), approx. 100 mm high. With 20 mm round steel slats, top and bottom, distance from top to bottom approx. 60 mm (of the round steel). For lashing and inserting stanchions 80 x 80 mm. Piece of stanchions W=80/ D=50/ L=1200 mm, hot-dip galvanized Piece of stanchions W=80/ D=80/ L=1200 mm, hot-dip galvanized Itjdpfx Akji Ri Hvexof Note: Stanchion pockets / stanchions are not designed for securing long material, pipes etc. on their own without wrapping around them. Mechanical rear extension with hand crank, can be extended by approx. 1,500 mm, can be locked every 500 mm, with support beam, can be loaded with 2000 kg over the entire width at the load center of gravity at approx. 500 mm, can be loaded with 1000 kg over the entire width at 1000 mm and can be loaded with 500 kg over the entire width at 1500 mm, incl. extendable underride guard with lighting, 2 pairs of stanchions W=80/ D=80/ L=1200 mm, hot-dip galvanized Open storage compartment for stanchions, on the front wall or underneath the loading area (for 10 stanchions 80 x 50 x 1200 mm and 4 stanchions 80 x 80 x 1200 mm) Axles + suspension SAF drum brake axles Axle/chassis laser-measured Reduction in tire wear and fuel consumption last axle self-steering, with automatic reversing lock via reversing light, and additional locking function on the vehicle via hand button. Air suspension with lift & lower valve Wheels and tires 235 / 75 R 17,5 at the manufacturer's choice Twin steel rims, factory silver Brake system 2-line compressed air brake system Spring-applied parking brake 2 non-interchangeable clutch heads at the front, without connecting cable EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Axle load detection via EBS-Canbus signal, for indication via display in the cab, truck must be prepared accordingly, no truck installation (no calibrated scales). Electrical system 24 volt, multi-chamber lights, amber LED lighting on the side 2 white position lights at the front 2 white/red rear lane departure lights 2 x 7-pin sockets at the front, without connecting cable 2 additional LED work lights, at the rear, switched via reversing light 1

Condition: new, machine/vehicle number: f79a9f15e7131d57a512793ab, empty load weight: 8,900 kg, maximum load weight: 15,100 kg, overall weight: 24,000 kg, axle configuration: > 3 axles, tire size: 235 / 75 r 17,5, Further information Chassis low loader trailer Welded steel construction Turntable with powerful ball bearing slewing ring Folding rear support 2 wheel chocks with holder Aluminum side bumpers Rear splash guards across the entire width Quarter-shell mudguards in front of 1st axle Widenings extendable to 3,000 mm (not in the rear slope) (However, the track width of the construction machinery or vehicles to be transported must not exceed outer frame width 2,550 mm) Storage compartment for wooden planks in the middle of the cargo bed Wooden planks 70 mm for widening to 3000 mm Low loader lashing eyes 1 pair of lashing eyes on offset per 5 tons 9 pairs of lashing rings at the top and sides, each 10 tons, embedded in the outer frame 2 x front on offset 7 x in the drop deck 6 pairs of lashing holes in the outer frame of the low bed, each with 5 to. (lashing strap attachment) Trailer drawbar Turntable Drawbar with tested 50 mm drawbar eye Axles + suspension SAF drum brake axles Axle/chassis laser-measured Reduction of tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearings and mechanical incl. axle load compensation front and rear Axle load compensation front and rear (rocker compensation) Wheels and tires 235 / 75 R 17,5 at the manufacturer's choice Twin steel rims, factory silver Brake system 2-line compressed air brake system Itedpfsi Ri Izsx Akxjf Spring-applied parking brake 2 non-interchangeable coupling heads at the front, with connecting cables to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red lane departure lights at the rear 1 LED rotating beacon with holder, switched via parking light (removable light) 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm 2 x 7-pin interchangeable plugs at the front, with connecting cable, floor Front offset with steel/ checker plate covering Then with 70 mm softwood floor, steel/checker plate covering in the wheel arch area Rear slope with 70 mm softwood flooring Drive-on ramps Steel ramps 2,800 mm long, 750 mm wide, can be moved sideways Covered with wood Hydraulic via tractor power take-off with throttle, actuation on the left side in FR Hydraulic connection with SVK plug NW 10/3, incl. connection hose Operating instructions With 10,000 kg axle load, a special permit is required, only indivisible load possible!!! The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. (Poor driving and trailing behavior possible due to incorrect load distribution) Country of registration / plates Country of registration: Germany With Dekra approval and expert opinion (according to §13 EG - FGV) 24/7 service hotline Incl. Prepared for two-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white on the sides and red on the rear Paint finish Frame DB 7350 nova gray 10-year warranty against rusting through Drawbar Galvanized or black, manufacturer's choice Drive-on ramps Hot-dip galvanized

Condition: new, machine/vehicle number: d9c951d746f03c05bc5470f89, empty load weight: 5 kg, maximum load weight: 29,045 kg, overall weight: 35 kg, axle configuration: 3 axles, tire size: 385/65 r22.5, Further information Chassis saddle forwarding Fine-grained steel welded construction, saddle plate with replaceable 2 kingpins Vario stanchion system 4 pairs embedded in loading area, can be pushed together to 2 100 mm and extended to approx. 3 500 mm for loading. Stanchions can be locked every 100 mm on an internal width of 2 100 mm to 3 000 mm, 4 pairs of divisible stanchions 600 mm + 1 200 mm, total height 1 800 mm removable. With an internal stanchion width from approx. 2 350 mm, excess width. Vario end walls Floor prepared for inserting 3 end walls. 4 x 5 pairs of Vario stanchion pockets for insertable end walls (front and rear) and 1 x 3 pairs in the middle for transporting 2 x 5,000 mm or 2 x 6,000 mm construction steel mats. 2 Vario end walls, each consisting of 1 pair of plug-in stanchions and 1 top crossbeam approx. 2200 mm wide. Cross beams can be extended by 220 mm on both sides, with lashing hole for tensioning. 1900 mm high Vario bulkhead, can be converted to 1300 mm or 700 mm high. 4 stanchion pockets embedded in the center of the floor for 80 x 80 mm stanchions 1 pair of supports at the bottom for Vario bulkhead at the front 1 pair of lower supports for rear Vario bulkhead Slightly slanted outer frame with Load-Lock profile for lashing strap attachment 14 pairs of lashing eyes additionally embedded in the outer frame, 5 tons each 24 to. 2-speed support winch, single-side operation, with straight lower section, without thrust compensation Extension ladder at the rear Wheel chocks with holder Aluminium side collision protection Galvanized steel underride guard Quarter-shell mudguards in front of and behind axle unit with anti-spray flaps on last axle only Impact protection at the rear Itjdpfx Akji Ri R Dexof 8 construction steel winches with wire rope and counter hooks, 4 x left and 4 x right with rope feed-through through the outer frame, 1 removable slip-on gearbox for construction steel winches - supplied loose (without bracket on the frame) 1 spare wheel holder for 1 e-wheel, with wheel fastening set 1 plastic toolbox, with drawer and shelf, w=650 / h=520 / d=670 mm, lockable with a padlock (lock not included) 1 closed stanchion stowage box, open at the top, below loading area, doors on both sides, w=450 mm/h=400/420 mm/d=2460 mm 4 lashing/stanchion rails embedded transversely in the floor across the entire width up to the outer frame (max. usable internal width between the outer stanchions approx. 2170 mm), approx. 100 mm high. With 20 mm round steel slats, top and bottom, distance from top to bottom approx. 60 mm (of the round steel). For lashing and inserting stanchions 80 x 80 mm. Note: Stanchion pockets / stanchions are not designed for securing long material, pipes etc. on their own without wrapping around them. Axles + suspension SAF disc brake axles with 430 mm disc diameter Axle/chassis laser-measured Reduction in tire wear and fuel consumption Air suspension 1st axle automatic lift axle, including forced lowering and starting aid, actuation of 3x brakes (starting aid is functional up to an axle load excess of 30% and up to a speed of max. 25 km/h) Axle lift below the recomm. Driving height, therefore no warranty for tire damage Brake system 2-line compressed air brake systemColor-coded cable routing for easy servicing. Spring-loaded parking brake 2 swap-proof coupling heads at the front, without connecting line EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The trailer may only be to

Condition: new, machine/vehicle number: 357314e4e176f8758d11ba42b, empty load weight: 4,500 kg, maximum load weight: 30,500 kg, overall weight: 35,000 kg, axle configuration: 3 axles, tire size: 385/65 r22.5, Further information Chassis tipper semi-trailer Fine-grained steel welded construction, lightweight design, fifth wheel plate with interchangeable 2 kingpins Curved front end Patented Telescopic support in the middle, unhitching with load not possible, when unhitched the vehicle must be at an angle to the rear. 2 wheel chocks with holder Folding underride guard Half-shell mudguards Integrated mudguard holder Stone-repellent surface with anti-spray flaps on last axle only 1 tarpaulin pole with bracket 2 towing hooks at the rear Axles+suspension SAF disc brake axles with 430 mm disc diameter Axle/chassis laser-measured Reduction in tire wear and fuel consumption Axles in off-road version, Air suspension 1st axle automatic lift axle, including forced lowering and starting aid, actuation of 3x brakes (starting aid is functional up to an axle load excess of 30% and up to a speed of max. 25 km/h) Hot-dip galvanized lift axle mechanism 10-year warranty against rusting through Brake system 2-line compressed air brake systemColor-coded cable routing for easy servicing. Spring-loaded parking brake 2 interchangeable front clutch heads, without connecting line EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lifting & lowering valve Vehicle stability system Automatic tilt lowering with shut-off valve Wheels and tires 385/65 R22.5 tires of the manufacturer's choice Steel rims, factory silver Electrical system 24 volt, multi-chamber lights, amber LED lighting at the sides 2 white position lights at the front 2 white/red rear lane departure lights 2 x 7-pin interchangeable sockets at the front, without connecting cable Hydraulics Low-pressure cylinder max. 170 bar, smallest stage hard-chlorinated, with HDK screw socket, fixed part, NW 48 mm (without hose connection). Hydraulic actuation via truck power take-off Troughs Aluminum box body made of high-quality, abrasion-resistant 5 mm thick front wall, with external walls made of 30 mm hollow chamber profiles, cleanly welded, with bulk material-repellent top rail profile. Inside with access to front wall (not in conjunction with Cramaro). Shovel and brush holder on the outside of the front wall. Itedoi Ri R Ispfx Akxof Greenline - conical and aerodynamic trough shape Membrane rear wall Rear wall as swing flap with double-jointed hinge, resting on the outside with double hook lock. Rear panel with rubber sealNote! Heat-resistant up to max. 170°C! Floor 6 mm thick throughout Standing platform with access, connection plate for air/electric and brake with large clearance for best possible operability. Roller tarpaulin on one side for depositing in FR-right, with central locking in FR-left Operating instructions For salt, lime, etc. We recommend a tipping cylinder with a hard chrome-plated piston rod so that it is not attacked by the material and rusts. The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. (Poor driving and trailing behavior possible due to incorrect load distribution) Country of registration / plates Germany Test approval according to EC 2007/46 24/7 service hotline Prepared for single-line license plate holder Contour marking with reflective strips according to ECE R 048, white on the sides and red on the rear

Condition: new, machine/vehicle number: 59ade5d1599dcdee29033ac46, empty load weight: 6,350 kg, maximum load weight: 28,650 kg, overall weight: 35,000 kg, axle configuration: 3 axles, tire size: 435/50 r19,5, Further information Chassis saddle forwarding Fine-grained steel welded construction, saddle plate with replaceable 2 kingpins Suspension bar for aluminum ramps across the entire width Frame in reinforced design for vehicle loading (up to outer frame) Itodpfx Aold Ihlskxof Outer frame with Load-Lock profile approx. every 400 mm, for lashing strap attachment 10 pairs of lashing mushrooms embedded in the top/outside of the outer frame, 10 tons each 24 to. 2-speed support winch, single-sided operation, with semicircular lower section and straight connecting plate, with thrust compensation Folding rear support 2 wheel chocks with holder Aluminium side bumper Galvanized steel underride guard Quarter-shell mudguards in front of 1st axle and behind each axle with anti-spray flaps behind each axle Pair of ferry eyes, marked yellow 1 Spare wheel holder for 1 e-wheel, with wheel mounting kit 2 plastic toolboxes, with drawer and shelf, w=650 / h=520 / d=670 mm, lockable with a padlock (lock not included) Container lock, 4 pairs of locks embedded in the floor for 2 x 20 foot or 1 x 40 foot containers, foremost position recessed as hinged lock 10 pairs of stake pockets embedded in the outer frame, 70 x 40 mm internal dimensions 10 stake pockets embedded in the center of the floor, 70 x 40 mm inside dimensions 2 lashing/stanchion rails embedded transversely in the floor across the entire width up to the outer frame (max. usable internal width between the outer stanchions approx. 2170 mm), approx. 100 mm high. With 20 mm round steel slats, top and bottom, distance from top to bottom approx. 60 mm (of the round steel). For lashing and inserting stanchions 80 x 80 rdnung: Position 2 and 4 according to Fliegl data sheet 20 stanchions, hot-dip galvanized Note: Stanchion pockets / stanchions are not designed for securing long material, pipes etc. on their own without wrapping around them Storage space for aluminum ramps, ramps can be inserted from the rear 3 pairs of folding eyelets 10 tons in the outer frame (1x in front of the bulkhead and 2x in the rear area). Axles + suspension SAF disk brake axles Axle/chassis laser-measured Reduction of tire wear and fuel consumption Air suspension 1st axle automatic lift axle, including forced lowering and starting aid, actuation of 3x brakes (starting aid is functional up to an axle load excess of 30% and up to a speed of max. 25 km/h) Axle lift below the recomm. Driving height, therefore no warranty for tire damage 2 ride heights, adjustable via hand knob, 1 x for semi-mounted height 980 mm 1 x for semi-mounted height 1100 mm (Note! Vehicle with inclined position) Brake system 2-line compressed air brake system Colored cable routing for easy servicing. Spring-applied parking brake 2 interchangeable clutch heads at the front, without connecting line EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! With lifting & lowering valve 2 ride heights, adjustable via hand knob, 1 x for fifth wheel height 980 mm 1 x for fifth wheel height 1100 mm (Note! Observe overall height, excess height at customer risk) Driving height in conjunction with lift axle, when the lift axle is raised, the total loading or semitrailer height increases by 50 mm (with Mega Flex only with low driving height or semitrailer height) Vehicle driving stability system Wheels and tires 435/50 R19.5 tires of the manufacturer's choice Stee

Condition: refurbished (used), battery capacity: 930 Ah, battery voltage: 80 V, total height: 784 mm, total length: 1,028 mm, total width: 1,000 mm, Tested forklift battery for your forklift truck - 80V 6PZS 930Ah - DIN A + 1 year warranty + Includes Aquamatik water refilling system + Includes end cell connectors & REMA 320 plug (other plug types can be fitted if required) + Capacity: min. 90-100% (C5 capacity test protocol will be provided on delivery) + Year of manufacture: 2024 Dimensions: Length 1,028 mm Width 1,000 mm Height 784 mm Weight: approx. 2,240 kg Itjdpjwzvw Ujfx Akxof Suitable for the following models, among others: Linde E 100 / 600 - 1471-00 Linde E 120 / 1200 - 1471-00 Linde E 120 / 600 - 1471-00 Linde E 140 / 1200 - 1471-00 Linde E 140 / 600 - 1471-00 Linde E 150 / 1200 - 1471-00 Linde E 150 / 600 - 1471-00 Linde E 16 - 386-02 - side battery change Linde E 160 / 1200 - 1471-00 Linde E 160 / 600 - 1471-00 Linde E 180 / 600 - 1471-00 Linde E 180 / 900 - 1471-00 Linde E 35 / 600 L - 388-00 Linde E 40 - 388-00 Linde E 40 / 600 HL - 1254-01 Linde E 40 / 600 HL - 388-00 Linde E 40 / 600 L - 388-00 Linde E 40 HL - 388-00 Linde E 45 / 600 HL - 1254-01 Linde E 45 / 600 HL - 388-00 Linde E 45 / 600 HL - 388-00 - side battery change Linde E 45 / 600 L - 388-00 Linde E 45 HL - 388-00 Linde E 50 - 388-00 Linde E 50 / 600 HL - 1254-01 Linde E 50 / 600 HL - 388-00 Linde E 50 / 600 L - 388-00 Linde E 50 HL - 1254-01 Linde E 50 HL - 388-00 Linde E 50 L - 388-00 Linde E100 / 1200 - 1471-00 Linde K - 5231-00 Linde K - 5231-00 - side battery change Linde P 250 - 127-00 Linde P 250 - 127-00 - vertical battery change Linde P 250 L - 127-05 Linde P 250 LWB - 5007-10 - side battery change Linde P 250 LWB - 5007-10 - vertical battery change Linde P 350 - 5007-10 - side battery change Still MX-X Still R 60-40 Still R 60-45 Still RX 60-40 Still RX 60-50 Jungheinrich EFG Jungheinrich EFG 540 Jungheinrich EFG 550 Jungheinrich EFG VAC 35 Jungheinrich EKX 515 Jungheinrich EKX 516 Toyota 7FBMF45 Crown TSP 6000-D Crown TSP 7000 Mitsubishi FB45-2 OM-Pimespo-Fiat XE 50 Steinbock-Boss WA 15 Other common battery sizes available on request. Transport available.

Condition: good (used), Used in good condition 4 pieces in stock Itodpfx Asvt Szzokxjf

Condition: used, maximum load weight: 28,933 kg, overall weight: 35,000 kg, axle configuration: 3 axles, first registration: 08/2015, loading space length: 13,620 mm, loading space width: 2,490 mm, loading space height: 3,000 mm, loading space volume: 101 m³, total width: 2,550 mm, total height: 4,000 mm, Equipment: ABS, * Edscha sliding roof * Haldex EBS, ABS, LSV * Lift axle * Toolbox * BPW Eco Plus axles with disc brakes ----* Tire size: 385/55R19.5 * Total length: 13,850 mm * Unladen weight: 6,067 kg * TÜV & SP: expired -----Subject to errors & prior sale Vehicle number 5726 WhatsApp support available! If you have any questions about the vehicle or need further information, feel free to contact us conveniently via WhatsApp Whatsapp Ijdpfx Akjvhvcfexotf Whatsapp

Condition: used, overall weight: 39,000 kg, first registration: 08/2021, next inspection (TÜV): 10/2025, loading space length: 9,500 mm, loading space width: 2,450 mm, loading space height: 2,150 mm, total width: 2,550 mm, total height: 3,850 mm, Equipment: ABS, Fliegl Aluminum Tipping Semi-Trailer - 48 cbm - Lift axle - SAF axle - Swing doors - LED work lights - Next technical inspection due: 10/2025 - Safety inspection due: 04/2026 Subject to errors and prior sale. Internal vehicle number: 11351. WhatsApp support available! Itedpfexcr H Ejx Akxsf If you have any questions about the vehicle or need further information, feel free to contact us via WhatsApp.

Condition: used, maximum load weight: 28,933 kg, overall weight: 35,000 kg, axle configuration: 3 axles, first registration: 08/2015, loading space length: 13,620 mm, loading space width: 2,490 mm, loading space height: 3,000 mm, loading space volume: 101 m³, total width: 2,550 mm, total height: 4,000 mm, Equipment: ABS, * Edscha sliding roof * Haldex EBS, ABS, LSV * Toolbox * BPW Eco Plus axles with disc brakes Iodpfx Aovhv H Rokxetf ----* Tire size: 385/55R19.5 * Overall length: 13,850 mm * Own weight: 6,097 kg * TÜV & periodic inspection: expired -----Subject to errors and prior sale Vehicle number 5732 WhatsApp support available! If you have questions about the vehicle or need further information, feel free to contact us conveniently via WhatsApp Whatsapp Whatsapp

Condition: excellent (used), Here we offer you a TPS Blue-M temperature convection oven. Itsdpfxedv Rabj Akxef TPS Blue-M temperature convection oven Blue M 7780 Specifications Temperature range: 15 ° C above ambient temperature up to 704 ° C Internal dimensions W x D x H: 25cm x 20cm x 20cm External dimensions W x D x H: 51cm x 38cm x 72cm Cladding dimensions W x D x H: 68cm x 48cm x 77cm Electrical power: 380V 3 phase 50 Hz CW-7780 has 8 shelf positions on 2" centers Frasen extractor hood, stainless steel version, without extractor/fan Type: CW-7780-JY-MP550 Condition: gebraucht / used Scope of delivery: (see picture) (Changes and errors in the technical data, specifications are reserved!) We will be happy to answer any further questions you may have on the phone.

Condition: good (used), Type: TS -70/1000-10 For sale is a CTS temperature test chamber Model: TS -70/1000-10 Cooling: water-cooled refrigeration unit Compressor has been replaced! Features: - Multi-touch control system - USB and Ethernet interfaces - Cable feedthroughs for test cables: 4 × Ø 125 mm - Safety temperature limiter Applications: - Environmental and longevity tests - Thermal cycling tests (stress screening) - Quality assurance and research & development - Electronics, automotive, materials testing Test chamber volume: 1,000 liters Test chamber dimensions: - Height: approx. 1,000 mm - Width: approx. 860 mm - Depth: approx. 1,100 mm External dimensions: - Height: approx. 1,950 mm - Width: approx. 1,270 mm - Depth: approx. 1,900 mm Temperature range: -70°C to +180°C Temperature deviation: ± 0.3 K over time Itsdpfxjxdi Ezj Akxof Temperature change rate: up to approx. 10 K/min Electrical connection: 400V 3/N 50Hz Rated power: approx. 23.1 kW Rated current: approx. 40 A Refrigerant: R404A / R23 Weight: 1,000 kg For your peace of mind as a buyer, please note: The following inspections and services are performed on our offered chambers in advance: 1. Functional check and replacement of necessary components 2. Refilling with legally compliant refrigerant if required 3. Leak test with certificate 4. Following successful checks, chambers undergo a documented test run Condition: used Scope of delivery: (See pictures) (Specifications and technical data subject to change and errors excepted!) We are happy to answer further questions by phone.