Used Roller Coating Uv-Drying Tunnel for sale (14,500)

Condition: new, Year of construction: 2025, functionality: fully functional, total height: 5,600 mm, total length: 11,200 mm, total width: 5,100 mm, type of input current: three-phase, warranty duration: 24 months, inner dimension height: 4,970 mm, inner dimension length: 11,000 mm, temperature: 80 °C, inner dimension width: 5,000 mm, air demand: 52,000 m³/h, input voltage: 380 V, heating capacity: 250 kW (339.91 HP), power: 45 kW (61.18 HP), fuel: liquid petroleum gas (LPG), input frequency: 50 Hz, energy consumption: 45 kWh, insulation thickness: 50 mm, nominal power: 250 kW (339.91 HP), sheet thickness steel (max.): 2 mm, Equipment: lighting, * Air Preparation Unit: The air preparation unit is a recirculation system that supplies the cabin with filtered fresh air and exhausts used air during the painting process. It heats the air to 60 °C, mixes the used air with 10% fresh air via an automatic multi-damper system, and reheats the air before routing it back into the cabin. The air is heated using a burner and a heat exchanger, both made of high-quality 304 stainless steel and housed within the fresh air unit. During painting, the air is filtered twice (via front and ceiling filters) before it enters the cabin. The contaminated air is also filtered twice (through inlet and outlet filters) before it exits via the exhaust unit. Air preparation units are insulated like the side walls to minimize heat loss and are protected against potential vibration and noise thanks to rubber seals on the covers. The exhaust air is regulated by a damper in the outlet duct, which helps control the internal pressure of the cabin. * PRINCIPLES OF CABIN OPERATION: The processes in the cabin are controlled via a control panel that manages the following steps: * PAINTING PROCESS: During painting, 100% fresh air is drawn in from outside and passed through front filters before entering the distribution chamber at ambient temperature. The air is then expelled by the extraction unit. Floor filters (paint stops) capture paint particles, and the air passes through the final exhaust filters before being discharged. * FLASH-OFF PROCESS: After painting, the cabin operates for approximately 15 more minutes to purge residual solvents and thinners. During this phase, fresh air from outside continues to circulate in the cabin. * DRYING PROCESS: In this phase, 80% of the air passing through the cabin is heated to 60 °C and supplied to the cabin via a distributor. As 20% of the solvent is released during drying, these solvents are expelled with the exhaust air. Industrial coatings are typically dried at 60 °C, but the cabin temperature can be adjusted via the control panel as required. * COOLING PROCESS: After the 30-minute drying process, the coil is deactivated via the control panel, the pneumatic damper closes, and the extraction system restarts. During the 5-minute cooling phase, fresh air from outside circulates in the cabin, after which the system stops automatically. ELECTRICAL AND ELECTRONIC EQUIPMENT: These control panels manage the functions and operation of all machinery and devices inside the cabin. The control panel is constructed from durable galvanized sheet metal and steel profiles and is fully enclosed to protect against dust and moisture. Electrical devices and control panels: Fjdpfxjwzl Hxj Albogg • The control panel contains essential components such as circuit breakers, fuses, indicator lamps, thermal relays, contactors, and connectors. • Heat-resistant cables are used for command and control lines between the panel and motors or other electrical devices. • Electrical wiring is designed to allow for cabin relocation if necessary. • Operating devices use 380 V 50 Hz, while control devices use 220 V.

Condition: used, Epson's first linehead, inkjet label press with LED UV curing ink, the L-6034VW/L-6034V enables high-speed printing that's ideal for short-to mid-run jobs, producing labels with outstanding scratch and weather resistance.  Digital Label Press Epson SurePress L-6034 Baujahr / Year 2016 - Serial-No. TE90010012 Bildgröße / Image Size max. 330 x 1000mm Bahnbreite / Web Width 80 - 340mm Substrate Support PP, PE and PET, coated paper, cast coated paper, and uncoated paper Substrate Thickness 3.14 - 12.60 mils (80 to 320 microns) Printing Technology PrecisionCore linehead inkjet technology Quick-drying UV ink Epson UV Ink / LED-UV-härtender Tinte White Ink Circulation System Automated control and in-line inkjet nozzle testing CMYK, White, and Multi-varnish inks installed in-line Maximum Print Resolution 600 x 600 dpi Fgedszzytdjpfx Albeg Print Speed Up to 49.21 ft/min (15m/min), Up to 24.61 ft/min (7.5m/min)  Ink Type LED UV Curing Inks Ink Configuration Black, Cyan, Magenta, Yellow, Multi-Varnish, White Online-Video-Inspection by WhatsApp - MS Zoom - Telegram On Stock Emskirchen/Nürnberg - Available Immediately - Can be test

Condition: like new (used), Year of construction: 2018, operating hours: 47 h, functionality: fully functional, i3 Microclean UPGRADE DX PELLET SANDERS (€2000) With this machine, you can also use loose 3mm pellets! And, of course, blocks. As good as new, 1-year warranty. Includes hoses and nozzle. We have various new parts in stock for Cold Jet machines. The COLD JET machine is suitable for industrial cleaning, both small and very large projects. The advantage of this machine is that it doesn't use new-generation electronics. It is one of the most aggressive machines on the market. This machine is in excellent condition. Cold Jet i3 Microclean & Dry Ice Press. Blasting complete with the following equipment: COLD JET i3 Microclean (47 HOURS OF USE) 1 x 20' blast hose 1 x Coldjet applicator 1 x nozzle One of the best machines in the world. No electronics. That’s why it’s reliable. And it’s inexpensive to maintain. For questions or to schedule a viewing, please contact DrDryice. All machines sold come with a 1-year warranty. Repairs and maintenance are available for Cold Jet machines. We also supply new Cold Jet machines. Contact us. Fedpfxoydpy To Albegg Worldwide Shipping. Cold Jet dry ice machine for sale, dry ice machine for sale, dry ice blasting machine for sale, dry ice blasting machine for sale, dry ice blaster for sale, dry ice blasting machine for sale, industrial dry ice blaster for sale, CO2 cleaning machine for sale, Cold Jet Aero 30 for sale, Cold Jet Aero 40FP for sale, Cold Jet Aero 40HP for sale, Cold Jet Aero 75 for sale, Cold Jet Aero 75 DX for sale, Cold Jet Aero75 DX, Cold Jet 75DX, used Cold Jet machine, second-hand dry ice blasting machine, Cold Jet Aero series, Cold Jet i3 MicroClean, Cold Jet E-CO2, Cold Jet SDI Select 60, Cold Jet IceRocket, Cold Jet Elite 20, Cold Jet Dry Icepress, Cold Jet pelletizer, dry ice blaster, dry ice cleaning machine, industrial dry ice cleaning system, pellet dry ice blaster, dry ice blasting equipment, cryogenic cleaning machine, CO2 blasting machine, carbon dioxide blaster, industrial cleaning, machine cleaning, maintenance cleaning, production line cleaning, mold cleaning without disassembly, dry ice paint removal, dry ice coating removal, rust removal, fire and soot damage cleaning, electrical cabinet cleaning, food industry cleaning, automotive cleaning, printing press cleaning, dry ice blaster 20 bar, high-pressure dry ice blaster, non-abrasive cleaning machine, refurbished dry ice machine, 20 ft blasting hose, dry ice blasting gun, venturi nozzle, Kärcher Ice Blaster, Kärcher IB 7/40, Kärcher IB 15/120, ASCO Jet, Cryoblaster, ICS Dry Ice, Nozzitec, Triventek, Cryonomic, Südstrahl, White Lion dry ice blaster, ICEsonic dry ice blaster, dry ice blasting machine Netherlands, dry ice machine Noordwijkerhout, industrial cleaning equipment Europe, export dry ice machine, DrDryice

Condition: used, Year of construction: 2014, A high-performance, fully operational industrial roller coating line by CEFLA. All machines are from the 2014 and operated continuously until the end of 2024 (discontinued only due to the end of production), well-maintained, and ready for immediate integration into production. This setup is perfect for furniture factories, flooring manufacturers, and door producers seeking top-tier automation and flawless surface finishing Fsdpfx Ajzu Rufjlbsgg Line Composition (15 Units Total): Fully operational: Coating & Filling Machines: 4 units - Smartcoater MF-EVO Roller Coaters 1 unit - CEFLA SP1-EVO Roller Filler/Spackling Machine UV Curing Ovens: 2 units - CEFLA UV-R M1 Curing Ovens 2 units - CEFLA UV-R M2 Curing Ovens Transporters: 2 units – CEFLA TB900 Transfer Conveyors Dimensions: 900 x 1580 x Adjustable Height 860–940. Non-operational - for spare parts/repairs: 4 units – CEFLA Smartcoater MF-EVO Roller Coaters

Condition: good (used), Year of construction: 2019, operating hours: 1,500 h, functionality: fully functional, total length: 2,420 mm, total height: 1,650 mm, total width: 13,600 mm, type of input current: three-phase, product height (max.): 250 mm, product width (max.): 630 mm, input voltage: 400 V, overall weight: 710 kg, power: 29 kW (39.43 HP), Ulma shrink tunnel. Only used as a replacement machine. Very good condition. Speed: 3 - 14.5 m/min | Double heating chamber | Dimensions: 2,420 x 1,360 x 1.650 mm | Weight: 710 kg | AIR FLOW CONTROL THROUGH FREQUENCY CONVERTER AND SOLID STATE RELAY | SHRINK TUNNEL PRECHAMBER AT INLET AND OUTLET | 220 MM HIGH CHAMBER | LEFT VERSION, PRODUCT RUNS FROM RIGHT TO LEFT | SELECTION FOR PURE "TRANSPORT MODE". Hot air fixation tunnel, an ULMA shrink tunnel model designed for shrinking film around previously packaged products. (Products previously packaged in side sealers, banding machines, flow wrappers, overlapping machines or any other packaging machine). Tunnel with high heating capacity, low consumption and low heat loss. Solid painted tubular steel frame. Easy integration into existing lines. Height-adjustable machine feet and wheels for installation and transportation. Product flow of the machine from right to left. Movable rollers with silicone coating. Fodpotva Sgofx Albegg Electronic temperature control. Control of the transport speed. Air is evenly distributed inside the chamber, guaranteeing great energy savings. Maximum insulation to reduce heat loss. Electric cabinet with ventilation. Protective devices and safety systems in accordance with CE standards. Consumption: 14.5 KW/h

Condition: good (used), Year of construction: 2003, 2 units of Giardina painting systems Year of manufacture from 2003 to 2009 Roller coating machine UV dryer 1 UV dryer 2 Fodpfezlq Utex Albsgg Roller coating machine, type G95/05 Baby, with GST UV dryer with 2 irradiation units UV dryer GST 1400/2

Condition: like new (used), Year of construction: 2017, functionality: fully functional, working width: 1,600 mm, total length: 75,000 mm, total width: 17,000 mm, Technical Details: Cefla painting/finishing line with roller coating machines for panel finishing *Maximum working width: 1650 mm *Automatic loading system with integrated robot *Line dimensions: 75 x 17 m *Line configuration: *3 x Cefla Smartclean 32-B brush cleaning machines *3 x Cefla Smartcoater MF Evo roller coating/painting machines *1 x Cefla Smartcoater SP1 Evo finishing machine *2 x Cefla UV-R M1 1600 UV curing tunnels (1 UV lamp each) *1 x Cefla UV-R M3 1600 UV curing tunnel (3 UV lamps) Fsdpoyv Hzgefx Albogg *1 x Cefla UV-R M2 1600 UV curing tunnel (2 UV lamps) *Cefla TR500 motorized conveyor line *Cefla automatic panel turner *Costa top sanding machine with 1 roller and 1 finishing pad *Automatic loading system with 2 x ABB robots

Condition: good (used), Year of construction: 2017, dispersion and UV varnishing sheet size min 152x152 mm max 760x760 mm paper thickness 0.1 - 1.2 mm UV varnish dispersion varnish 120 g/m² without surface treatment and higher 150 g/m² with surface treatment and higher 200 g/m² with surface treatment and higher automatic setting time 5 minutes Fgodpeyv Dm Hjfx Albog automatic washing time 10 minutes Automated Set-up Time 5 Minutes Automated Wash-up Time 10 Minutes 8.5” x 11” / 215 mm x 280 mm sheets width 12,700 sheets/hour 12” x 18” / 305 mm x 450 mm sheets width 9,900 sheets/hour 14” x 21” / 355 mm / 530 mm sheets width 8,800 sheets/hour 21” x 30” / 530 mm x 750 mm sheets width 6,300 sheets/hour 28” x 40” / 710 mm x 1020 mm sheets width 5,000 sheets/hour Painting speed 4,600 B2/hour anilox rollers for the machine 3;9;12;18 Automated Set-up Time 5 Minutes Automated Wash-up Time 10 Minutes UV drying IR drying (suitable for dispersion varnish and primer for HP Indigo) kit for processing thin materials varnish application using a chamber doctor blade high feeder 2 independent varnish circuits with automatic washing Anti-Ghost system innovated sheet delivery system

Condition: like new (used), Year of construction: 2007, operating hours: 151 h, functionality: fully functional, warranty duration: 12 months, Coldjet Aero30 Machine – Like New We have various new parts in stock for Cold Jet machines. This machine is suitable for industrial cleaning, including small and very large projects. One advantage of this machine is that it doesn’t rely on new-generation electronics. It is one of the most powerful machines on the market and is in excellent condition. Cold Jet Aero 30 Dry Ice Blasting Machine – Complete with the Following Equipment: COLDJET AERO 30 DRY ICE (151 HOURS OF USE) 1 x 20’ Blasting Hose 1 x Cold Jet Applicator 2 x Nozzles – NEW Fgsdpfxjwg R Rms Albjg One of the best machines in the world. It has no electronics, which is why it is so reliable. Furthermore, maintenance costs are relatively low. For inquiries or to arrange a viewing, please contact us at Dr. Dryice. All machines sold come with a 1-year warranty. We also offer repairs and maintenance for Cold Jet machines. We also supply new Cold Jet machines. Contact us. Worldwide shipping is available. Cold Jet dry ice machine for sale, dry ice blasting machine for sale, industrial dry ice blaster for sale, CO2 cleaning machine for sale, Cold Jet Aero 30 for sale, Cold Jet Aero 40FP for sale, Cold Jet Aero 40HP for sale, Cold Jet Aero 75 for sale, Cold Jet Aero 75 DX for sale, Cold Jet Aero75 DX, Cold Jet 75DX, used Cold Jet machine, second-hand dry ice blasting machine, Cold Jet Aero series, Cold Jet i3 MicroClean, Cold Jet E-CO2, Cold Jet SDI Select 60, Cold Jet IceRocket, Cold Jet Elite 20, Cold Jet Dry Icepress, Cold Jet pelletizer, dry ice blaster, dry ice cleaning machine, industrial dry ice cleaning system, pellet dry ice blaster, dry ice blasting equipment, cryogenic cleaning machine, CO2 blasting machine, carbon dioxide blaster, industrial cleaning, machine cleaning, maintenance cleaning, production line cleaning, mold cleaning without disassembly, paint removal with dry ice, coating removal with dry ice, rust removal, fire and soot damage cleaning, electrical panel cleaning, food industry cleaning, automotive cleaning, printing press cleaning, dry ice blaster 20 bar, high pressure dry ice blaster, non-abrasive cleaning machine, refurbished dry ice machine, 20 ft blasting hose, dry ice blasting gun, venturi nozzle, Kärcher Ice Blaster, Kärcher IB 7/40, Kärcher IB 15/120, ASCO Jet, Cryoblaster, ICS Dry Ice, Nozzitec, Triventek, Cryonomic, Südstrahl, White Lion dry ice blaster, ICEsonic dry ice blaster, dry ice blasting machine Netherlands, dry ice machine Noordwijkerhout, industrial cleaning equipment Europe, export dry ice machine, DrDryice.

Year of construction: 2014, condition: like new (used), COOLING (DEEP FREEZING) HORIZONTAL TUNNEL (Instruction manual added) Liquid nitrogen deep-freezing of foodstuffs Model ZIP FREEZ SILVER LINE 2 type 90X12 Overall dimension in m: Lengh 10,30 Width 2,30 Height 1,81 Height in cleaning position 2,31 Deep-freezing chamber Lengh 8,70 m Effective width 1,20 m Height 0,25 m Surface in m2 10,44 Weight 3200 kg Made by SEPAR, France Fsdpfsyf Hlijx Albogg Was used for cooling of the hot filled desserts In complete with Associated Controls, Conveyor and Pipework

Condition: like new (used), Year of construction: 2019, operating hours: 66 h, functionality: fully functional, Size 60 x 75 cm, Presscenter XL 2, program-controlled wash-up device for inking rollers, blanket wash, and impression cylinder wash, Alcolor Vario dampening system, Combistar air-cooled cooling and recirculation unit, Autoplate, antistatic device in the feeder, double sheet detector, Weko AP 262 powder spray unit, AMS LED UV dryer, maximum paper thickness 0.8 mm, maximum speed 15,000 sheets/h, perfecting 2-3 or 5- Fedpfx Aleykr Rzobjgg

Condition: excellent (used), Year of construction: 2015, operating hours: 355 h, Cold Jet Aero 75 DX Machine We have various new parts in stock for Cold Jet machines. This machine is suitable for industrial cleaning, including both small and very large projects. An advantage of this machine is that it does not rely on new-generation electronics. It is one of the most powerful machines on the market and is in excellent condition. Cold Jet Aero 75 DX Dry Ice Blasting Machine, complete with the following equipment: COLD JET AERO 75 DX DRY ICE (335 HOURS OF USE) 1 x 20’ Blasting Hose 1 x Coldjet Applicator 2 x Nozzles (NEW) This is one of the best machines in the world. It has no electronics, which is why it is reliable and not expensive to maintain. For inquiries or to arrange a viewing, please contact us at DrDryice. All machines sold come with a 1-year warranty. Fsdpfszkq N Iox Albogg We also offer repairs and maintenance services for Cold Jet machines. We also supply new Cold Jet machines. Contact us. Worldwide shipping available. Cold Jet dry ice machine for sale, dry ice blasting machine for sale, industrial dry ice blaster for sale, CO2 cleaning machine for sale, Cold Jet Aero 30 for sale, Cold Jet Aero 40FP for sale, Cold Jet Aero 40HP for sale, Cold Jet Aero 75 for sale, Cold Jet Aero 75 DX for sale, Cold Jet Aero75 DX, Cold Jet 75DX, used Cold Jet machine, used dry ice blasting machine, Cold Jet Aero series, Cold Jet i3 MicroClean, Cold Jet E-CO2, Cold Jet SDI Select 60, Cold Jet IceRocket, Cold Jet Elite 20, Cold Jet Dry Icepress, Cold Jet pelletizer, dry ice blaster, dry ice cleaning machine, industrial dry ice cleaning system, pellet dry ice blaster, dry ice blasting equipment, cryogenic cleaning machine, CO2 blasting machine, carbon dioxide blaster, industrial cleaning, machine cleaning, maintenance cleaning, production line cleaning, mold cleaning without disassembly, paint removal with dry ice, coating removal with dry ice, rust removal, fire and soot damage cleaning, electrical cabinet cleaning, food industry cleaning, automotive cleaning, printing press cleaning, dry ice blaster 20 bar, high-pressure dry ice blaster, non-abrasive cleaning machine, refurbished dry ice machine, 20 ft blasting hose, dry ice blasting gun, venturi nozzle, Kärcher Ice Blaster, Kärcher IB 7/40, Kärcher IB 15/120, ASCO Jet, Cryoblaster, ICS Dry Ice, Nozzitec, Triventek, Cryonomic, Südstrahl, White Lion dry ice blaster, ICEsonic dry ice blaster, dry ice blasting machine Netherlands, dry ice machine Noordwijkerhout, industrial cleaning equipment Europe, export dry ice machine, DrDryice

Condition: like new (used), Year of construction: 2023, operating hours: 800 h, functionality: fully functional, total length: 1,400 mm, total height: 2,300 mm, total width: 250 mm, workpiece weight (max.): 72 kg, For sale: Nearly new automatic powder coating line, installed in 2023, with approximately 800 operating hours. Current layout footprint: approx. 12 x 28 m, H 5 m. Price and dismantling timeline subject to individual agreements. Layout modifications available: pre-treatment tunnels can be added, and the curing oven can be reconfigured as a straight-through tunnel suitable for parts exceeding 6 meters in length. We can provide a complete quotation including dismantling and international relocation upon separate arrangement. Excellent opportunity to acquire an almost-new line at a lower price and with much shorter lead times compared to a new installation. Monorail conveyor: - Speed: 0.9 – 3.3 m/min - Automatic lubrication - Automatic chain tensioning unit - Chain pitch: 270 mm - Total length: 131 m - Total load capacity: 9500 kg - Steel supports between the floor and conveyor Automatic powder coating booth Gema: - PVC booth: MagicCompact EquiFlow BA04 - MagicControl 4.0 control panel - Photo-cell frame for automatic gun control - 16 x OptiGun GA03-P automatic guns - 1 x OptiSelect GM04 manual gun Fgedpfsx H Tadex Albog - 17 x OptiSpray AP01.1 powder feed pumps - OptiCenter OC07 powder feeding system - Ultrasonic sieve US07 for OptiCenter - 2 x ZA07-23 reciprocators with X-axis automatic control - MonoCyclone EZ05-16, 16,000 m³/h - Powder filter: 16,000 m³/h, 30 kW - Big-Bag system for waste powder collection - CO₂ explosion protection system - Manual spray wall / trolley unit shown in pictures NOT INCLUDED Powder curing oven: - Hybrid heating (electricity or gas) — offers unique flexibility to choose the most economical energy source - Installed capacity: 300 kW - Max. temperature: 220°C - Siemens PLC control panel

Condition: like new (used), Year of construction: 2015, functionality: fully functional, roll diameter: 75 mm, total width: 1,000 mm, conveying length: 3,500 mm, Roller track 1000x3525mm roller line, transport track several pieces /ct1967 Manufacturer: BUDDE Fördertechnik Length: 3525 mm Width: 1000 mm Height: 250 mm Roller: 990 mm Wheel center distance: 75 mm Fedpfx Alsubahgjbegg Can be sorted, several pieces for sale

Year of construction: 2018, condition: excellent (used), functionality: fully functional, TYPE 318:: COATING DRUM 1600 For the application of various taste and aroma giving materials by using various aromatising techniques. The special drum profile offers following main advantages: - optimal rolling of the product for uniform coating - minimum possible friction/damage of the product surface - no hidden corners, easy to clean, bacteriologically optimal surface. Adjustable drum speed, by frequency controlled AC gear motor 1.5 kW. Drum diameter: 1600 mm Drum length: 4000 mm Drum height : 3270 mm TYPE 284:: DRUM DRIER/ROASTER 1600 PTFE Newly developed short and medium range infrared roaster for special thermal post treatment of expanded extrudate. The whole drum is coated with a low-wear PTFE-layer. This secures processing of extremely sticky coated extrudates. Unlike the conventional hot air drying process, this drying system works with a very high degree of efficiency. The whole machine is made of rust free stainless steel. The radiation elements are attached to a common carrying arm in the drum. The roasting drum runs on special, low-noise carrier rollers and corresponds to the safety regulations and is equipped with a corrosion free covering to reduce energy losses. The rpm of the drum is adjustable continuously. The drive is carried out by a three-phase motor 1.5 kW. Drum diameter: 1600 mm Electrical heating power: 126 kW Fjdpfxewbqx He Albegg Drum length:4300 mm Drum height : 2960 mm TYPE 361:: COOLING DRUM 1600 For cooling of sticky and hot extruded products under rotation for separation. The cooling is carried out with the help of room air, which is blown controllably into the drum by a middle pressure blower 1.85 kW AC. Please note: depending on the product characteristics, additional cooling might be necessary for breakfastcereals before the product can be packed. Drum diameter :1600 mm Drum length: 4000 mm Drum height : 2890 mm

Condition: like new (used), Year of construction: 2014, operating hours: 10 h, functionality: fully functional, machine/vehicle number: 16238, total length: 12,600 mm, total height: 1,500 mm, total width: 1,475 mm, type of input current: three-phase, product height (max.): 200 mm, product height (min.): 80 mm, product length (min.): 80 mm, product length (max.): 200,000 mm, product width (max.): 450 mm, product width (min.): 14 mm, input voltage: 400,230 V, working height: 900 mm, overall weight: 1,900 kg, input frequency: 50 Hz, space requirement width: 3,000 mm, This machine was bought in 2015 and has only been installed, calibrated and tested. We have never been in commercial use. Fgsdjzzybhspfx Albsg Has only been stored in our room temperated warehouse. We planned to use it for own production, but not all plans are realized. So this is a brand new packaging machine with roller conveyers and heat tunnel. All documentation is avaliable. The machine is located in Norway and can be inspected and tested here. We paid € 70.000,- for this machin inclusive heat tunnel and roller conveyors in 2015

Condition: ready for operation (used), Year of construction: 2017, functionality: fully functional, machine/vehicle number: 157, working width: 400 mm, overall weight: 2,200 kg, total width: 400 mm, For sale: a complete, used line for applying and curing oil/oil-wax on wooden floors (Soest + Prochera). I am selling a set of four machines that form a line for oil-waxing floorboards, used in a production facility for two-layer parquet in Krotoszyn. The line has not been used for approximately 3 months and has been regularly maintained and repaired during this time. The set includes: 1. SOEST RC-L-400 (Netherlands): application unit with a roller, serial number 157, year of manufacture 05/2017, total weight 580 kg, CE marking. 2. SOEST VP-400-2P-B (Netherlands): spreading/brushing unit (spreading oil, stain, or other coatings using pads and brushes), serial number 264, year of manufacture 05/2017, total weight 480 kg. 3. SOEST UV-3-400 (Netherlands): curing/drying unit, serial number 286, year of manufacture 04/2018, total weight 780 kg, CE marking. 4. PROCHERA SPL1-400C (Poland, Ziębice): brushing/polishing unit, no. 7, year of manufacture 2024, weight 355 kg, power 2 kW, CE marking. All units have a working width of 400 mm and are equipped with integrated conveyor belts and control/electrical cabinets. Total weight of the set: approx. 2,195 kg. Technical condition: unused for approx. 3 months, regularly maintained and repaired. Fodpezrm Ucefx Albegg Price: PLN 182,500 net (negotiable), plus VAT. Note: the line is sold as used, in its current condition. Before purchasing, an on-site inspection and individual verification of suitability for a specific type of finish are recommended (e.g., UV oil vs. classic oil-wax cured by air).

Condition: repair required (used), Year of construction: 2007, Roller profiling line for manufacturing profiles for dry construction, without a hydraulic unit. Fgodpfxozy Ekfe Albjg Location: In our workshop.

Condition: excellent (used), Year of construction: 2015, functionality: fully functional, total length: 43,000 mm, total height: 3,800 mm, total width: 20,000 mm, type of input current: three-phase, workpiece weight (max.): 200 kg, compressed air connection: 9 bar, workpiece height (max.): 2,400 mm, workpiece length (max.): 7,200 mm, We are offering this BEWAP MACRO 6 POWDER COATING MACHINE – Complete Powder Coating Line 7.2 m, year of manufacture 2015, in very good condition. Complete setup for surface treatment, including 2 powder coating booths and 2 curing ovens for powder coating applications. Machine in perfect working order. Year 2015. Surface Treatment Booth (made of 316 L stainless steel, membrane spray pumps, dosing pumps, stainless steel pickling tanks with immersion heaters, rinse tanks, effluent tank, dosing pumps, reverse osmosis unit, water softener) Drying oven (gas burner, control cabinet) 2 manual powder coating booths with automatic feed and extraction Curing oven (gas burner, control cabinet) Structure with manual overhead conveyor: 3 transfer trolleys with 3 lifting beams (200 kg per beam) 2 lift stations for loading and unloading parts 36 lifting beams in total Operation with 3 beams simultaneously Compatible with Qualicoat and Qualilaquage certification Maximum part dimensions per lifting beam: Maximum part length: 7200 mm Maximum part height: 2400 mm Maximum part width: 500 mm (configuration for 1000 mm width possible) The line is to be dismantled and removed on site Price: €150,000 (excl. VAT) If you have any questions or need further information, please do not hesitate to send us a message or call us. Viewing is possible. Fedpfx Aeyc S Htjlbjgg

Condition: excellent (used), Year of construction: 2019, operating hours: 7,000 h, functionality: fully functional, MACHINE CONSTRUCTION: - Cast iron bed, spindle head, and saddle system developed through computer-aided design and analysis (CAD/CAE), ensuring high rigidity and vibration damping - Fully supported table guide in every working position Fedpszzf Rujfx Albjgg - X-axis (table movement) on 2 precision cylindrical roller guides, supported by 6 runner blocks each - Y-axis with 2 precision cylindrical roller guides - Z-axis with hardened and ground guideways, with TURCITE-B coating - Guideway protection via metal telescopic covers - Hydraulic counterweight / balance system - CE conformity Axes: - Preloaded ballscrews with large pitch for long-lasting precision - Digitally controlled, liquid-cooled ballscrew on the X-axis - Gear-driven ballscrews, ballscrew nuts with centralized lubrication, and lifetime-lubricated bearings CONTROLLER & ELECTRONICS + CAPACITY: - High-speed CNC, 1 ms block processing time - Storage capacity: 120 GB SSD - Technology program memory: 100 GB SSD - Number of processor cores: 4 CNC operating system: - User interface operating system: Windows 10 - Technology program storage: WINDOWS file system - Total storage capacity (system program, PLC, parameters, technology program memory) on a single SSD - New user interface (40-00005216-00w) SCREEN: Color graphical LCD touchscreen COMMUNICATION: USB, Ethernet, EtherCAT MEASURING SYSTEM: - HEIDENHAIN absolute EnDat 2.2 - PROGRAMMING: ISO, myNCT TECHNICAL DATA: - X-travel: 2100 mm - Y-travel: 1500 mm - Z-travel: 1000 mm Distance from spindle nose to table surface: 200~1000 mm Distance between columns: 1650 mm Distance between table and gantry/crossrail: 1710 mm AXES: - Rapid traverse speed X / Y / Z axis: 20 / 20 / 15 m/min - Max. working speed: 10 m/min - Motor power: 4 kW ACCURACY (according to JIS6338): - Positioning accuracy: +/- 0.01 mm (In the entire working area!) - Repeatability: +/- 0.004 mm TOOLING: - Max. tool diameter / with adjacent tool omitted: 125 / 215 mm - Max. tool length: 400 mm - Max. tool weight: 20 kg - Optional tool taper: SK50 Accessories & Equipment: - Angle head (manual) - Chip conveyor - Coolant flush gun - 15 pcs of SK50 tool holders - Machine leveling feet - Manuals The machine is in good used condition and operates accurately.

Condition: excellent (used), Year of construction: 2023, operating hours: 60 h, functionality: fully functional, machine/vehicle number: AE00003516, grinding width: 1,370 mm, overall weight: 1,800 kg, grinding height: 170 mm, workpiece height (max.): 170 mm, workpiece width (max.): 1,350 mm, - Wide-belt sanding machine DMC SD 70 RCS 135 - DMC SD 70 model, RCS 135 version First "R" unit with roller and second "CS" combination unit with roller/sanding pad - Working width mm 1,350 Min./Max. working height mm 4-170 Sanding belt dimensions mm 1,370x2,620 Main motor power kW (HP) 11 (15) Feed rate m/min 4.5/9 - 160/85 rubber-coated calibrating roller, diameter 160 mm, 85 Sh - 1st position - R160/45 rubber-coated sanding roller, diameter 160 mm, 45 Sh - 2nd position - Hard sanding pad with manual adjustment of the working height Fgodpezydafefx Albeg - Motor power, 1 unit: 11 kW (15 HP) - Electronic ammeter for the main motor to display current draw - Electronic display of the working height - Electronically controlled sanding belt oscillation - Rubber pressure rollers - Kickback protection at the infeed before the first unit - Rubber feed carpet, 60 SH - Roller table with two rollers at the infeed and outfeed of the work table - Carpet feed with two speeds 4.5 / 9 m/min with gear motor - Automatic carpet centering

Condition: excellent (used), Year of construction: 2007, machine/vehicle number: 060308, functionality: fully functional, power: 6.9 kW (9.38 HP), input voltage: 400 V, input current: 19 A, input frequency: 50 Hz, type of input current: three-phase, temperature: 40 °C, number of chambers: 1, control type: PLC-controlled, Equipment: CE marking, documentation/manual, GIARDINA MOS® 3D Static Microwave Drying Chamber Professional static drying system designed for the drying of coated wooden components, particularly for water-based coatings. The GIARDINA MOS® 3D technology uses microwave energy for controlled and homogeneous three-dimensional drying. After removal of the water component from the coating, a low-temperature hot-air circulation phase completes the drying and curing process. The system is suitable for three-dimensional and assembled wooden components, including furniture, chairs, window and door components, profiles and turned parts. Technical data: Fsdpfeztvf Tox Albsgg Manufacturer: GIARDINA FINISHING S.r.l. Model: MOS® 3D Year of manufacture: 2006 Serial number: 060308 Electrical power: 6.9 kW Supply voltage: 400 V Frequency: 50 Hz Rated current: 19 A PLC controlled Air recirculation motor: 3 kW / 4 HP CE marked Original operating and maintenance documentation as well as electrical diagrams are available. The machine was recently taken out of production and is currently dismantled and stored in a dry warehouse. It was in regular operation prior to being taken out of service.

Condition: good (used), Year of construction: 2015, machine/vehicle number: 0-200-24-0779, functionality: fully functional, input voltage: 400 V, input current: 55 A, input frequency: 50 Hz, type of input current: three-phase, workpiece height (max.): 60 mm, edge thickness (max.): 20 mm, total length: 10,825 mm, Used single-sided HOMAG edge-banding machine for straight edges – KAL 370 For pre-milling (jointing trimming), gluing and post-processing of various kinds of edging materials. Fixed stop on the left side. Year of Manufacture: 2015 EQUIPMENT / SPECIFICATION BASIC MACHINE - with 80 mm wide conveyor chain with rubber-coated chain pads, - workpiece thickness 8 to 60 mm - top pressure with compound V-belt, automatic height adjustment (to workpiece thickness) - panel support with roller guide, extractable approx. 700 mm - glue roller drive in case of feed stop - hand switch /remote control for setup – mode - adjustable infeed fence with NC-axis (CAN-bus) - Jointing trimming 2 motors (clockwise, counterclockwise), 2x4kW, rear motor w. jumping function GLUING SECTION V20, consisting of: - QA60 glue application unit, with PTFE-coating (Teflon), with manual quick-adjustment glue gates - pneumatic clamping of glue application in mount - Pre-melter for EVA glue - Edge magazine, edge thickness min. 0,4 mm to max. 20 mm Edge width (height) max 65 mm - modes: edge rolls, (veneer) strips, solid wood edging - Pressure zone with automatic horizontal adjustment (NC CAN-axis) to edge thickness, Fgodpfsztl Scox Albjg 1 driven & 4 non-driven pressure rollers. POST-PROCESSING SECTION: - Snipping (end-trimming) unit PK85 horizontal, 2 motors, with straight/chamfer cutting function - Rough trimming 2x1.15 kW, top/bottom - Corner rounding FK11, 2 motors (top/bottom) with various trimming heads, motorised adjustment - Universal trimming unit, (e.g. grooving), 3.5 kW, tiltable, w. electro-pneumatic jumping control - Multi-Profile (radius-) scraping MN11 with automatic positioning by NC-axis (CAN) - Flat scraping (glue joint) FA20, top/bottom, (version with 3 tracer rollers) - Buffing unit FP10, top/bottom Control / software: - powerControl PC 23 PowerTouch - woodCommander 5 Machine dimensions 1085 x 180 x 235 cm (with opened doors)

Condition: like new (used), Year of construction: 2013, functionality: fully functional, overall weight: 500 kg, MAKOR TF/P PLUS coating machine 19.06.6512 TYPE TF/P Plus Max. working width 150 mm Max. height 120 mm Adjustable feed rate max. 140 m/min Fedjytc Rkjpfx Albogg Upper pressure rollers with drive x 6 Pressure force adjustment via pneumatics Lower pressure rollers with drive x 6 CE marking Year of manufacture 2013 Product description: - Paint without waste - Robust and efficient transport with 6 motor-driven pressure units. - Various application heads guarantee results, even for filling and defect repair products. Designed for continuous application of coating, gesso, and paint on strips, picture frames, and profiles with an extrusion system, using a correspondingly shaped steel counter-template. Construction made of steel sheet and tubular steel. Guaranteed forward movement via no. 6 lower metal rollers and no. 6 upper rubber pressure wheels, variable with adjustable speed via an inverter. The upper pressure wheels are mounted on freewheel bearings to reduce uneven wear. Pneumatic distribution panel equipped with a selector for engaging the upper pressure wheels and corresponding independent pressure regulators. OPTION TO PURCHASE THE FOLLOWING MACHINES AT INDIVIDUAL PRICES: 1. Profiling machine for grinding wheels and silicone wheels from the Italian company MAKOR, price €1,500 - Year of manufacture: 2003 - Serial number: 5933 - Diameter of profiled wheel: 160 - 200 mm - Diameter of profiling disc: 180 - 200 mm - Weight: 280 kg 2. MAKOR ST/100 film slitting machine, price €1,200 3. MAKOR TEP 3000 conveyor belt, price €700

Year of construction: 2019, condition: good (used), Sturm Coating System Description For sale is a complete industrial Sturm robotic painting system manufactured in 2019. The automated coating system was used for the serial coating of components and originates from an industrial production facility. The used paint line includes, among other components, a paint booth, drying and cooling zones, conveyor technology, and several KUKA and Yaskawa industrial robots. The system is complemented by a thermal exhaust air purification unit. Thanks to its automated system design, the robotic painting line is particularly suitable for industrial applications in the automotive industry, metalworking, and serial production. An inspection at the Hamburg site is possible by prior appointment. Technical Data & Scope of Delivery Manufacturer: Sturm (system) / KUKA & Yaskawa (robots) Year of manufacture of main system: 2019 Previous operation: Three-shift operation, condition consistent with age System components: Units, drying and cooling zone, paint booth, loading and unloading station Included robots / peripherals: Several spare KUKA robots, models KR 210L 150-2 / KR 210 2, manufactured between 2006 and 2012 Associated robot control cabinets 2x Yaskawa EPX 2900 robots 1x thermal post-treatment / exhaust air purification system, VeniaKab / RNV Condition Information Control technology: According to the plant maintenance department, the control technology is up to current technical standards Electrical and mechanical components: Predominantly in condition consistent with age or in good condition Fsdpozka Sfsfx Albsgg Cybersecurity Data Deletion For security reasons, all hard drives from the robots and PC-based stations were removed. Dismantling Ex Works Hamburg There are two options for dismantling, loading, and transport: You carry out the dismantling and loading yourself on site. If you do not have the necessary personnel or equipment for dismantling, we can provide the complete dismantling, professional removal from the production hall, and loading as an additional service. The costs are calculated by prior agreement and according to the work involved. Please contact us in advance if you are interested. “Everything from a single source: We are pleased to offer suitable bank financing for your project.” komplett-konzept.leasingo.de You can find further new and used items in our shop. International shipping costs available upon request.