Short Time Heating System

Kreuzmayr 6000 Liter

Year of construction: 2022, condition: ready for operation (used), An unused and still originally packaged continuous pasteurizer Pietribiasi Michelangelo Srl is available. Throughput capacity milk: 1500l/h, throughput capacity cream max. 40% fat: 750l/h, inlet temperature: 6°C, pasteurization at 68/74/88°C, outlet temperature: 6°C, capacity foreflow tank-balance tank: 100l. With centrifugal pump for product and cleaning, additional section and hot water group, plate heat exchanger with stable internal construction in AISI304, special heat exchanger plates Sondex Denmark in AISI316, surface area per plate: 0.08m², flow volume per plate: 0.21dm³, special gaskets made of nitrile snap-on without glue, hydraulic test pressure: 8.0bar, test temperature: 110°C, heat recovery: 85%, temperature profile 6-68/74/88-6/33/45°C - 4 sections, final heating outlet cheese/yogurt: 33/45°C, media: approx. 3000+3000l/h hot water 92°C, approx. 3000l/h cooling water 2°C, holding tube for 15s, design stainless steel AISI304, switching system for product to the foreflow tank by means of pneumatic changeover valve as soon as the heating temperature is approx. 2°C below the setpoint, 2x hot water generators for pasteurization and final heating, closed circuit, assembly for automatic water supply, automatic system for hot water supply, expansion vessel, pump, brazed plate heat exchanger. Documentation available. An inspection on site is possible. Laodpfx Abeyln D Tozog

Condition: good (used), Consisting of : - 3 tanks of 18000 litres - 3 tanks of 15300 litres - With walkways - Material: AISI 316 - Square discharge door (bottom) - Motorised mash discharge - Round manhole DN 400 (cylindrical part) - Total emptying: ball valve Ø 40 Friedrich no 2 - Partial drain: ball valve Ø 40 Friedrich no 2 - Taster - Recirculation with ball valve Ø 40 Friedrich no 2 - Dome Ø 400 mm, eccentric - Central dome DN 400, with a cylinder-grid fixed inside (to keep the mash cake wet) Dimensions : - 3 tanks 18000 litres: Ø 2000 mm, height 5600 mm - 3 tanks 15300 litres: Ø 2000 mm, height 4800 mm - Ground clearance: approx. 550 mm Laedpfx Abeib H Ddszog

Year of construction: 2026, condition: as good as new (ex-display), Parts cleaning machine / spray cleaning system, type TR450 Ledpfxjfbt Sio Abzeag The spray-rotation cleaning system, type TR450, is an automatic cleaning and degreasing system with a lid that can be easily opened upwards. The system is designed for cleaning individual parts and/or bulk goods in baskets with dimensions of L x W x H 520 x 320 x 200 mm. For the cleaning process, the basket must be closed with a lid. The cleaning result depends on the fact that the parts in the basket can be slightly tumbled when cleaning bulk goods. The fill level in the basket must be taken into account for this purpose. The system is also equipped with a flood basin under the parts basket, which enables the parts to be immersed and scooped out, resulting in an even better cleaning result. including the following equipment: • Completely made of stainless steel 1.4301 inside and outside • Level monitoring and automatic fresh water refill • Insulation of the entire system • Hot air drying (power: 11.6 kW) • Steam extraction • Oil skimmer for bath maintenance • Automatic fresh water refill • 1 small parts basket 520 x 320 x 200 mm, mesh size: 6 x 6 mm, incl. height-adjustable locking lid Connection power: approx. 20 kW (32 amp plug)

Year of construction: 2019, condition: like new (used), MUT RWO 360/400-1150 Retort Heat Treatment Furnace - Like new: hardly used - Documentation available (both electronic and physical) - Pallet with spare parts included Lajdpfxjiryyas Abzsg TECHNICAL DATA System type: RWO 360/400-1150 Furnace chamber temperature: ≤ 1150 °C for max. 1 hour Operating temperature: ≤ 1100 °C, ≤ 1050 °C in a vacuum Control stability: ± 2 K Temperature homogeneity: ± 6 K in the range of 600 °C to 1150 °C at the end of the stabilization period Control voltage: 230 VAC / 24 VDC Furnace working space: 360 x 400 mm Load: ≤ 50 kg Heating: Three-zone Pressure: ≤ 350 mbar Final vacuum pressure in the cold state: < 5 * 10-5 mbar in a clean, dry furnace Installation area: 900 x 1900 x 3000 mm Total system weight approx.: 1500 kg Sound pressure level: < 70 dB We assume no liability for the accuracy, completeness, and currency of the information provided.

Year of construction: 2020, condition: new, 1000l/h Stainless steel frame on 4 adjustable feet Minimum / Maximum Level sensor in the pressure tank Stainless steel pressure vessel The product is pressed through a multi-nozzle head in the tank ; Product Pump: Inlet check valve of the product Sight glass at the inlet of the product CO2 pressure control valve for installation on the CO2 bottle Sight glass in the pressure vessel Lsdpfocx Smbox Abzsag Max. Pressure : 6 bar incl . electronic control incl . booster pump

Year of construction: 1990, condition: used, machine/vehicle number: 9072492, nominal capacity: 100 kVA Laodpez H Dyefx Abzeg throat: 500 mm spark plug air gap: 330 - 500 mm electrical connection: 400 V kW space needed: 700 x 1420 x 2000 mm weight: 750 kg

Condition: new, Year of construction: 2023, functionality: fully functional, machine/vehicle number: 61036721, clamping force: 6,500 kN, screw diameter: 70 mm, clearance between the columns: 1,110 mm, displacement volume: 1,078 cm³, injection pressure: 1,877 bar, injection weight: 981 g, opening stroke: 3,200 mm, plate height: 1,540 mm, drive type: Hydraulisch, clear span: 3,200 mm, tool weight: 2,200,000 g, Injection Moulding Machines Directly from the Manufacturer! As the manufacturer KraussMaffei, we offer you our certified and flexible stock machines: The hydromechanical two-platen clamping unit of the GXW machine sets new standards in terms of quality and productivity. With the sophisticated GuideX sliding shoe, forces are ideally absorbed and the service life of the moulds is extended. The innovative GearX locking system engages instantly and reliably. Powerful, user-friendly and value-retaining. TECHNICAL DATA: KM 650 / 2000 / 2000 GXW G06 (Order 38618339) CONTROL SYSTEM - MC 6 with 24'' TFT color screen with multitouch functions CLAMPING UNIT - Clamping force: 6500 kN - Max. mould opening force: 455 kN - Daylight opening (h x v): 1110 x 960 mm - Platen size (h x v): 1540 x 1440 mm - Mould installation height min. - max.: 1550 mm (without centre platen) - Opening stroke: 3200 mm - Max. mould opening distance: 1650 mm - Max. mould weight: 22,000 kg INJECTION UNIT 1 SP2000 - Screw diameter / type: 60 mm / thermoplastics - Effective L/D ratio: 23.3 - Injection pressure: 2420 bar - Shot volume: 792 cm³ - Shot weight at max. stroke for PS: 720 g - Injection speed: 140 mm/s - Injection throughput: 396 cm³/s - Screw drive speed: 285 rpm - Plasticizing throughput: 72.2 g/s - Nozzle contact force: 82 kN INJECTION UNIT 2 SP2000 - Screw diameter / type: 70 mm / thermoplastics - Effective L/D ratio: 20 - Injection pressure: 1877 bar - Shot volume: 1078 cm³ - Shot weight at max. stroke for PS: 981 g - Injection speed: 140 mm/s - Injection throughput: 539 cm³/s - Screw drive speed: 285 rpm - Plasticizing throughput: 98.3 g/s - Nozzle contact force: 82 kN ELECTRICAL PARAMETERS - Connected load: 341 kW - Power supply: 400 V / 50 Hz, 3 phases with neutral conductor WEIGHT & DIMENSIONS - Net weight: 43.5 t - L x W x H: 11.89 x 3.22 x 2.77 m ADDITIONAL EQUIPMENT - Wear-resistant plasticizing unit - BluePower full insulation for plasticizing cylinder - Open nozzle - BluePower ServoDrive - Pneumatic valve: 1-fold (BWAP), 1-fold (FWAP) - Pneumatic cascade valves: 6-fold (BWAP), 6-fold (FWAP) - Hydraulic core pull: 2-fold (BWAP), 2-fold (FWAP) - Mould heating: 96 zones (3.5 kW each) Ljdpfx Abew U N Ixozsag - Euromap interface for handling: E18 - Euromap central computer interfaces: E67, E77, E78, E63, E82.1 - Adaptive Process Control (APC+) - Graphic analysis package - Sliding table with turning unit, servo-driven - Vertical centre platen - Parallel clamping & opening during injection process with bar parallelism control between FWAP and centre platen or BWAP and centre platen - ColorForm interface signal interface for connecting an RPM unit - Electrical interface for HRS-Flexflow system - Electrical interface and hydraulic valves for "1-K dummy operation" - Interface for connecting a CoMo-Kistler Injection Basic System with good/bad part separation The machine is located at our plant in Parsdorf and is available at short notice. Further additional options can be offered on request. We look forward to your enquiry.

Year of construction: 2026, condition: new, The fruit washer with a mill for fruits and vegetables is made entirely of stainless steel and is equipped with a sorting grate, a washing tank, and a conveyor belt. The fruits are immersed in water for a pre-wash. Afterwards, they are transported further via the conveyor belt, which thoroughly cleans the fruits with fresh water. After cleaning, the fruits enter the mill, where they are processed with the desired sieve to achieve the required mash consistency. • Easy to clean • Low maintenance requirements • Belt speed is steplessly adjustable in both directions • Equipped with 2 swivel wheels • Equipped with 2 fixed wheels Technical Information • Nominal capacity: 2000 kg/h • Power requirement: 3 kW, 400 V, 10 A • Mash discharge height: 1400 mm • Connection for washing tank: G 6/4” • Connection for cleaning: G ½” • Material: WNr. 1.4301, AISI 304 stainless steel • Water consumption: approx. 12 L/min Dimensions: Length: 2700 mm Width: 840 mm Ljdjv Srguepfx Abzoag Height: 2270 mm Weight: 150 kg

Condition: used, Year of construction: 2019, functionality: fully functional, table length: 8,000 mm, table width: 2,540 mm, overall weight: 8,000 kg, sheet thickness steel (max.): 100 mm, cutting length (max.): 8,000 mm, cutting width (max.): 2,540 mm, drill diameter: 40 mm, FICEP TIPO G25LG - CNC PLATE PROCESSING LINE (DRILLING, MILLING, THERMAL CUTTING) | YEAR 2019 The Ficep Tipo G25LG is a CNC plate processing line for combined drilling, milling, tapping and thermal cutting of steel plates in structural steel fabrication. Built in 2019 - a young machine in its class on the used market. All processes run in a single pass on a rigid double-bridge gantry frame. CONDITION & REFURBISHMENT Refurbished and inspected by a certified technician, ready for operation. - The exact scope of reconditioning varies from machine to machine and is disclosed individually upon serious interest. - Viewing possible by arrangement (machine reconditioned - no demonstration under power). FUNCTION & APPLICATION The vertical mono drilling unit with automatic tool changer (ISO 40) performs drilling, milling, tapping, centre-punching and countersinking. The Hypertherm XPR300 plasma torch and the integrated oxy-fuel cutting unit handle thermal cutting - from thin sheet to heavy plate. The line is operated via the Ficep Pegaso CNC control. Infeed and outfeed roller conveyors with material transfer (8 m each) ensure continuous material flow. Typical applications: structural steel fabrication, steel trading and plant engineering. TECHNICAL DATA - Manufacturer: Ficep | Model: Tipo G25LG | Year: 2019 | Serial number: 36098 - Machine type: CNC plate processing line (drilling / milling / thermal cutting) - Condition: used, refurbished by certified technician - Frame design: double-bridge gantry frame, welded | Machine weight: 8,000 kg - Plate width: max. approx. 2,540 mm, min. 200 mm - Plate thickness: max. 45 mm (plasma cutting), max. 100 mm (drilling) - Drilling heads: 1 (vertical mono drilling unit) | Tool holder: ISO 40 - Max. drilling diameter: 40 mm | Max. drilling/milling depth: 100 mm - Max. spindle speed: 7,000 rpm | Spindle power: 15 kW - Plasma cutting torch (straight): 1 | Plasma source: Hypertherm XPR300 | 300 A - Oxy-fuel cutting unit: included - CNC control: Ficep Pegaso CNC - Processes: drilling, milling (incl. straight/curved slots, Y/J weld-edge preparation), tapping, centre-punching, countersinking, marking, scribing, straight plasma cutting, oxy-fuel cutting On request (to be confirmed bindingly during inspection): processing length, tool magazine stations, min. plate thickness for drilling, min. drilling diameter, pass line height, longitudinal and cross positioning speeds, connected load and machine dimensions. SCOPE OF DELIVERY - 1 x Ficep Tipo G25LG CNC drilling, milling and thermal cutting line (year 2019) Laodpfx Asu Dw I Eebzjg - 1 x Ficep Pegaso CNC control - 1 x Vertical mono drilling unit with automatic tool changer (ISO 40) - 1 x Plasma cutting torch (straight) | 1 x Hypertherm XPR300 plasma source (300 A) - 1 x Oxy-fuel cutting unit - 1 x Infeed roller conveyor with material transfer (8 m) | 1 x Outfeed roller conveyor (8 m) - 1 x Extraction system for plasma cutting LOGISTICS & LOCATION Location: Ulft (Netherlands), directly at the German border. Dismantling, transport, installation and commissioning by ASM by arrangement - individually calculated upon request. ABOUT ASM Arendsen Steel Machinery (ASM): specialist for refurbished Ficep structural-steel machinery. Further machines on request. CONTACT / INQUIRY Viewing by arrangement | Price on request. Sale exclusively to commercial customers (B2B).

Condition: used, Year of construction: 1998, Automatic PET bottle blowing machine Manufacturer: SIDEL Type: SBO 16/16 S1 Year of manufacture 1998 Capacity: 16,000 for 1.5 L bottles and up to 19,000 bph for 0.5 L bottles Installed power: 347 kW Includes 1.5 L moulds Preform feeder Chiller cooling unit Technical condition: used machine, functional until dismantled. The machine is currently dismantled, assembled in elements and prepared for transport. Lasdpfx Aeutni Rebzog Full and original technical documentation.