Hydraulikaggregat 70 bar

Integral Hydraulik K 1831-1

Condition: good (used), Make: OMERA Type: R4 / 12-2 Year: 1976 Table length : 1900 Table width : 1000 Steady arm throath HOR : 670 Steady arm throath VER: 940 Stroke cylinder : 350 Column diameter : 200 Specifications Metric US Standard There are no specifications for this machine (yet). Dimensions (Estimate) Length 3000 mm Width 2200 mm Height 2500 mm Hnsdpfxskvnumo Ag Iol Weight 2800 kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Condition: used, Eccentric punch press HAULICK + ROOS type RVD 125 double column - eccentric press Machine No. 212560 Year of construction 1981 pressure force 125 ton. table size 880 x 800 mm table opening 470 x 140 mm column width 900 mm column width lateral 415 mm ram stroke 45 mm slide adjustment travel 0-80 mm Installation height on the picture 340 mm Stroke rate 50 to 300 strokes/min. Hnodpjhlnzkofx Ag Isl Motor power main drive 22 kW Mains connection 380 volt, 50 Hz - Double connecting rod drive with 4-fold eccentric shaft for off-center ram pressure load - adjacent electrical cabinet - NC roll feed EBU, width 250 mm, year 2003 - adjacent control panel for roll feed - strip running direction from left to right space requirement (press) L x W x H 3000 x 2000 x 3020 mm transport height 2950 mm weight of the press approx. 11 ton.

Condition: good (used), Year of construction: 1981, functionality: fully functional, SINGLE-DIE TUBULAR RIVET HEADER NATIONAL M5 Rebuilt on 2024. New electrical system. Operational, working. Available for any test. Number of die: 1 Number of pieces per min.: 300 Length Rivet: 20 mm. Depth of Pierce (max.): 5 mm. Cutoff diameter: 5 mm. Hsdpfjtxni Nex Ag Isnl Floor space (width): 1.300 mm. Floor space (length): 2.690 mm. Power of main motor: 7.5 KW Net weight: 3.100 kg. Gross weight: 3.700 kg.

Condition: as good as new (ex-display), Year of construction: 2008, machine/vehicle number: LSP 100T, Productions-Hydraulic press with H-column 100t with guidance Manufacturer: Stenhoj Denmark Year of construction: 2008 Pressure force max. 1,000 kN / 318bar Press cylinder, stroke length: 400mm Press table with T-slot 1,500x900mm above 1,500x1,050mm below Stand passage 1,700mm Condition as good as new, the machine was only used for test runs and has been in stock since then. Hodpfjg Rn Efsx Ag Ienl All statements without guarantee. Without transport costs.

Year of construction: 2018, condition: new, machine/vehicle number: DMPMFG200x200, Magnetic filter grid in housing / cabinet construction V2A quality (for free-fall applications to investigate dry and free-flowing bulk solids) Magnetic grid 200x200mm High-quality cabinet construction completely closed Easy cleaning by pulling out the magnetic cores High quality magnetic filter rods completely closed Magnet NdFeB N45, Br 8500 Gauss Tmax 80 ° C 4x M10 threaded rod incl. Wing nut as clamping unit Guide rod center: Entrance level right Hnodpfxedtdwaj Ag Iel Outlet below

Condition: new, Year of construction: 2025, Band width: max. 38 mm Feed length: max. 50 mm Hedo Ea U Hjpfx Ag Ienl Band thickness: 0.05...1.02 mm Stroke rate: max. 260 rpm at full feed length Feed force: 90 N Optionally with mechanical control valve or optionally with electric valve (24V or 230V) Many other band widths and feed lengths available.

Condition: used, color: yellow, first registration: 01/1995, * Manufacturer: HYSTER,* Type: H2.50XM,* Serial No.: D177B22181S,* Attachment: S/S 2.00-1.50 1067 mm,* Year of manufacture: 1995,* Drive: Diesel,* Operating hours: 18151.8 h,* Unladen weight: 4265 kg,* Reverse tilt: 6 degrees,* Tire size: 7.0 x 12 (front). 6.0 x 9 (rear),* Tire pressure: 0 (front / rear),* Track width: 1125 mm,* Lifting capacity with vertical mast and additional equipment as specified above,* Lifting height: 5550 mm,* Load capacity: 2040 kg at 500 mm, 1860 kg at 600 mm, 1710 kg at 700 mm, subject to alterations, prior sale and errors excepted. Hedpoi Tfapsfx Ag Ienl

Condition: ready for operation (used), A combined heat and power unit (CHP), consisting of three diesel generators installed in containers, is available. 1) Engine: MAN 12-cylinder turbo, type: D 2842 LE 20, generator: Krauter, type: D-SYN-GEN, kVA: 400, kW: 360, A: 577, Hz: 50, speed: 1500 rpm. Including DELF synchronization, heating water outlet, table cooler, preheating and oil change device. 2) Engine: MAN 12-cylinder turbo, type: D 2842 LE 20, generator: Leroy-Somer, type: LSA K 475 L10, kVA: 375, kW: 300, A: 400, Hz: 50, speed: 1500 rpm. Including DELF synchronization, heating water outlet, table cooler, preheating and oil change device. 3) Engine: Daimler Benz 8-cylinder turbo, type: AGV 12, generator: Krauter, type: D-SYN-GEN, kVA: 350, kW: 230, A: 400, Hz: 50, speed: 1500 rpm. The combined heat and power unit has a total output of around 1100kVA. Including table cooler, V2A heat exchanger, containers and switch cabinets. All generators are installed in containers and are therefore easy to transport. Hnsdpfx Astwqzrjg Iel

Condition: used, Year of construction: 2021, machine/vehicle number: HB 2022-A-073, pressing force: 300 t, Portal straightening press with 300 T capacity a) idle and pressing speed up to 17 mm/sec. b) opening speed up to 55 mm/sec c) table size 2500x1600mm d) open height 700 mm e) total size approx. LBH 4500 x 2300 x 3700 mm f) Oil temperature indicator on the tank g) Lubrication via grease nipple h) table in grid construction,with T grooves according to customer's request, otherwise 22mm i) operation on swivel arm, mounted on the bridge j) pressure adjustment from 50 T to 300 T via MONITOR k) bridge moves by two gear motors, via racks l) Cylinder moves to the left and to the right via toothed racks m) Machine body double painted n) Cylinder induction hardened Type of construction Press design PORTAL PRESS Thermally neutral 80 - 120 °C Number of operating sides 3 side Forces Pressing force max. 3,000 kN Free ripping force max. 500 kN Pressure build-up time Closed die Steel to steel Max. 3 sec. Dimensions Max. Opening width 700 mm Stroke and min. opening 700 mm/ 0 mm Table height above floor approx. 9ß0 mm Height above floor (headroom) approx. 3700 mm Hall height min. 5.000 mm Deflection Determined at max. clamping force with 70% occupancy < = 0.8 mm/m Weight Total weight of press without operating materials and table plate approx. 22 T Speeds Fast closing with 17 mm sec. Pressing speed 8 mm sec. Opening 55 mm sec. Sound pressure Sound pressure level, measured at 1.5m height at the control panel after max. 78 db(A) DIN 45635-T16-KL3 Hydraulics Number of pressing cylinders 1 pc. Operating pressure max. 350 bar Pressing pressure build-up time 02. mz sec. Pressure accuracy during pressing stroke +/- 5 bar Main pump BOSCHREXROTH approx. 93 L/min Oil volume approx. HLPD 46 MW 900 liters Ambient temperature max. 45 °C Oil temperature max. 55 °C Electrical system Main supply 400 V AC Control voltage 24 V DC Frequency 50 Hz Hnedpfoh Agnuex Ag Iol Hydraulic connection Main motor IE3 22 kW Total connection Approx. 30 kW

Condition: refurbished (used), Year of construction: 2020, pressing force: 500 t, pressure:500 t passage width:1100 mm stroke:600 mm weight of the machine ca.:ca. 22,8 t Table area:1100 x 800 mm ram surface:1100 x 800 mm Daylight Opening:800 mm Hydraulic:300 bar closing speed:60-200 mm/sec pressing speed:0 - 9,5 mm/sec opening speed:28-200 mm/sec Table height above ground level:900 mm height over floor:5100 mm workpiece weight max.:2000 kg workpiece weight top:1000 kg halls height:min. 6500 mm Number of pressing cylinders:1 St. Hodpfxjffamvj Ag Ijnl number of driving cylinders:2 St. :ca. 270 Lt./min. Oil Tank Capacity:600 l main drive:75 kW Control technology from Siemens:S 7 Safety control:PILZ Multi