Heatable / coolable stainless steel tank

Inox Behälter GmbH

Condition: used, Used stainless steel tank Last application: Chemicals Article number: 10909 Volume: 1450 liters Type: Standing on 4 rollers Material (in contact with media): 1.4301 / AISI304 Design: Single-walled Tank dimensions: Inner diameter: 1400mm Cylindrical height: 1000mm Height of legs: 240mm Overall height: 1200mm Overall width: 1446mm Iiedpfxjzxz Ane Ahyeh Materials: Inside: 1.4301 / AISI304 Exterior parts: 1.4301 / AISI304 Features: Nameplate: yes Distance from drain to bottom: 190mm Outlet diameter: 50mm

Condition: good (used), Year of construction: 1997, Stainless Steel Tank 500 Liters with SCABA Agitator and Measurement Technology Manufacturer: Food Tech Tank Type: Stainless steel tank with agitator Capacity: 500 l Year of manufacture: 1997 Quantity available: 2 units Agitator: SCABA Motor power: 0.37 kW Protection class: IP55 Iiodpfx Asyxvwpohysh Load cells: FLINTAB Type: SB4-5kN-GP Measurement technology: Endress+Hauser Liquiphant Supply voltage: 10–55 V DC Equipment and Accessories Agitator fully assembled Internal mixing system with agitator blades Manhole with cover Filling opening with grate insert Level sensor Endress+Hauser Liquiphant FLINTAB load cell system integrated into support frame Discharge at the bottom with connection Pipe fittings and valves

Condition: new, Factory-new agitated vessel with dissolver Type: STOC2200RWD Volume: approx. 2,266 liters Design: Vertical construction on three height-adjustable feet Construction: Single-walled Medium-contacting material: 1.4301 stainless steel (AISI304) Surface: External satin finish, internal BA (IIId) Internal weld seams: Pickled, passivated and brushed Max. operating pressure: Atmospheric Max. operating temperature: 95°C Top: 15° conical top Bottom: 15° conical bottom with central outlet DN50 DIN11851 Tank dimensions: Tank diameter: 1,430 mm Cylinder height: 1,250 mm Total height: 2,160 mm Foot height: 500 mm Outlet to floor distance: 350 mm Equipment: 1x Ø 500 mm manway cover with swivel bracket on top, EPDM gasket 1x agitator flange connection IEC200 3x calotte / height-adjustable feet 1x stainless steel vent/bleeder valve DN50, non-pressurized, on the top 1x DN50 DIN11851 outlet port centered in the bottom 1x DN50 DIN11851 port with blanking cap on the top Isdpfew Dy Hlsx Ahyoih 1x DN65 DIN11851 port with blanking cap on the top 2x lifting lugs on the top 1x ladder bracket on the cylinder 1x nameplate Agitator: Dissolver Manufacturer: Schwarzer Rührtechnik GmbH Type: SRTDMK/7.5-1500 Power: 7.5 kW Speed: 1,410 RPM Operating voltage: 3PH 400V - Heavy-duty agitator shaft mounted to the agitator motor with muff coupling - Agitator shaft dynamically balanced for smooth running within the speed range - 1 piece dissolver disc Ø 275 mm screwed onto the end of the agitator shaft - Stainless steel flange with V-ring seal, EPDM - Motor mounted flexibly on neoprene rubber-metal buffers

Condition: new, Factory-new electrically heated stainless steel mixing tank, insulated, with propeller agitator, including operating manual and CE declaration of conformity. Model: EBB150RWP Also available with alternative agitator types and in other sizes. Iiedpfoym Uclsx Ahyjh Capacity: 152 L Approximate dimensions: Ø 660 mm x cylindrical height 625 mm Total height: 910 mm (+ agitator motor) Material: 1.4301 (V2A) stainless steel Finish: IIIc / 2B Weld seams ground Maximum operating temperature: 110°C Operating pressure (tank): atmospheric -Upright design on castors -Top: Hinged lid, half bolted, half hinged, with removable stainless steel safety grid -Bottom: Flat bottom with lateral outlet DN50 DIN 11851 and disc valve, EPDM gasket -Agitator flange connection on top -2x push handles -1x type plate Agitator: Propeller agitator Power: 0.25 kW Speed: 980 rpm Operating voltage: 3-phase 400 V

Condition: used, Manufacturer: Manuel OrtizModel: MLIType: Hammer millMotor power: 2.2 kW / 3000 rpmScreen: 2 mmMachine dimensions: 50 x 45 x 125 cmWeight: 40 kg Iiedpfx Asyhhw Eohyoh

Condition: new, Factory-new, electrically heated stainless steel mixing tank Article number: EBB150RWAD Volume: 152L Dimensions approx.: Ø 660mm x cylindrical height 625mm Overall height: 910mm Material: 1.4301 stainless steel V2A Surface: Matte finish inside and out Welds ground smooth Iisdpfx Ahoh Hxxfeysh Operating temperature max.: 110°C Operating pressure tank: ATM -Vertical design on rollers -Top: Central cross member for the agitator with two hinged lid halves -Bottom: Flat bottom with side outlet DN50 DIN11851 and disc valve -Agitator flange on the top -2x handle for pushing -1x nameplate Heating system: Indirect heating Double jacket around the tank with glycerine filling as the heat transfer medium. Heating is carried out by an electric heating element in the double jacket. Power: 9KW Operating voltage: 3PH 400V Incl. supply line 16A CEE plug Centric agitator: Slow-speed anchor agitator with wall scrapers Type: SRTGMK/0.37-9.5 Manufacturer: Schwarzer Rührtechnik GmbH Power: 0.37KW Speed: 0-9.5 RPM Operating voltage: 1PH 230V Material in contact with product: 1.4301 stainless steel -Gearbox and motor in the latest aluminum technology, manufacturer Getriebebau NORD -Gearbox with food-grade approved oil filling "Klüber" -Solid agitator shaft attached to the agitator motor with a sleeve coupling, detachable -Agitator shaft balanced for smooth running in the speed range -1 piece of large anchor agitator in the tank, welds ground smooth, arranged close to the wall -2 Teflon wall scrapers in the cylindrical area, one at the bottom -Stainless steel flange with shaft seal, EPDM Speed control: Compact frequency inverter on the agitator motor with on/off switch and potentiometer Control: 5m cable and RCD socket switch, undervoltage release Eccentric agitator: Speed-adjustable dissolver agitator Type: SRTMKD/1.1-1500-Vari Manufacturer: Schwarzer Rührtechnik GmbH Power: 1.1KW Speed: 0-1690 RPM Operating voltage: 3PH 400V Material in contact with product: 1.4301 stainless steel -Motor in the latest aluminum technology, manufacturer Getriebebau NORD -Solid agitator shaft attached to the agitator motor with a sleeve coupling, detachable -Agitator shaft balanced for smooth running in the speed range -1 piece of dissolver disc Ø 125mm screwed onto the end of the agitator shaft, seal O-ring, EPDM -Stainless steel flange with V-ring seal, EPDM -Stainless steel spacers for motor mounting Speed control: Frequency inverter mounted on the motor, manufacturer Getriebebau NORD. On/off switch, potentiometer, phase inverter Control: CEE plug switch on the tank with undervoltage release and phase inverter, emergency stop

Condition: new, Factory-new electrically heated stainless steel agitator tank EBB90RWP Including operating manual and CE declaration of conformity. The double jacket is filled with thermal oil, which is heated by an electric heating element. Alternatively available with other agitator types and in other sizes. Volume: 97L Dimensions approx.: Ø 540mm x cylindrical height 625mm Total height: 910mm (+ agitator motor) Material: 1.4301 stainless steel (V2A) Surface: inside and outside finely ground (matte finish) Weld seams ground smooth Max. operating temperature: 110°C Operating pressure (tank): Atm - Upright design on castors - Top: folding lid, half bolted, half hinged, with removable stainless steel grating for reach-in protection - Bottom: flat base with lateral outlet DN50 DIN11851 and disc valve - Agitator flange on the top cover - 2x push handles - 1x nameplate Propeller agitator Power: 0.25 kW Isdpfx Aoym Arbohyjih Speed: 980 rpm Operating voltage: 3PH 400V

Condition: new, Year of construction: 2024, functionality: fully functional, nominal power: 90 kW (122.37 HP), rotational speed (max.): 5,760 rpm, rotational speed (min.): 1,592 rpm, total height: 3,437 mm, total length: 3,275 mm, total width: 2,500 mm, type of cooling: air, compressed air connection: 6 bar, Equipment: rotational speed infinitely variable, The impact mills of the REKORD 212-630 series in the welded housing design are robust universal mills for demanding industrial applications in continuous operation. ● Size: 630 mm (nominal rotor diameter) ● Mill housing: Heavy-duty welded stainless steel housing, pressure surge resistant up to 10 bar (AISI316L), with product-contacting surface finish Ra ≤ 1.6 μm for easy cleaning, equipped with a pivoting door and safety interlock type HAAKE (key transfer system); monitoring of housing and bearing temperature, vibration monitoring ● Mill inlet: JACOB pipe; DN 150 mm Iedpfex Ac Rbox Ahyeih ● Mill outlet: Ground material and air discharge downward into a suction hopper, optimized for connection to the conveying line to the total separator ● Mill drive: Belt drive, three-phase motor, energy efficiency class IE3 (manufacturer SIEMENS), 90 kW, 3~ 400 V, IP55; suitable for operation with frequency inverter ● Sealing materials: Silicone; PTFE, sealing material conforms to EU and FDA food hygiene standards ● Grinding elements: Pin rotor: 4 pin rows, pin Ø 7 mm (wear-reduced); Pin stator: 3 pin rows without external pin circle, pin Ø 7 mm ● Bearings: Designed for toughest operational demands in continuous industrial service, heavy-duty bearing housings with temperature and vibration monitoring (early detection of potential bearing failure and avoidance of hot surfaces) ● Inert gas supply/monitoring for shaft seal on product chamber side ● Run monitoring to detect operating faults ● Machine frame: The complete unit – mill, drive with motor, tensioning rails, belt drive, and belt guard – is installed ready for use on a sturdy machine frame with height-adjustable machine feet Main components of the offered system include: ● Product feed/transfer from customer’s upstream process and transfer to a rotary valve (certified ATEX protection system); ● Industrial pin mill type REKORD 630-SSt with welded housing and ground surfaces; ● Product separator with discharge rotary valve (certified ATEX protection system); ● Pneumatic conveying line with air inlet/outlet, including suction blower; ● WITHOUT control system, without frequency inverter

Condition: new, Factory-new electrically heated 1150L stainless steel agitator tank with insulation and propeller agitator, including operating manual and CE declaration of conformity. Type: EBB1150RWP Also available with alternative agitators and in other sizes. Volume: 1150L Dimensions approx.: Internal Ø 1190mm x cylindrical height 1000mm External Ø: 1390mm Total height: approx. 1300mm plus agitator drive Material: 1.4301 / AISI304 stainless steel Surface: IIIc/IIId / satin finish Iijdpfxsw Dy D Do Ahysh Internal welds ground smooth Max. operating temperature: 110°C Max. operating pressure: atmospheric - Upright design on four tubular legs with forklift channels - Top: Central traverse with two hinged covers - Bottom: Flat sloped base with lateral outlet DN50 DIN11851 and butterfly valve, EPDM gasket - Insulation: 50mm mineral wool around the cylinder, hermetically welded stainless steel 1.4301 cladding Equipment: 1x Top traverse with two hinged cover halves, clamp function for the lid Stainless steel grating below the hinged lid, bolted and removable 1x Agitator flange on the top 1x Inlet port DN50 DIN11851 on the top 1x Outlet fitting with butterfly valve DN50 DIN11851, EPDM gasket 1x nameplate Propeller agitator for low-viscosity media Power: 0.75 kW Speed: 1410 rpm Operating voltage: 3PH 400V

Condition: good (used), Used, insulated stainless steel tank with agitator and double jacket Last use: Food Article number: 10340 Volume: Approx. 6300L Type: Standing on three legs Material (in contact with media): 1.4301 / AISI304 Design: Insulated with double jacket at the bottom Bottom: Flat bottom Top: Domed Operating pressure according to nameplate: ATM Tank dimensions: Iodsd Nap Rspfx Ahyeih Tank diameter: 2030mm Cylindrical height: 2000mm Distance from outlet to bottom: 330mm Height of legs: 390mm Overall height: 2940mm Overall width: 2050mm Materials: Inside: 1.4301 / AISI 304 Outside: 1.4301 / AISI 304 Equipment: Domed lid Ø 490mm Outlet diameter: 40mm Slow-speed agitator Cylinder insulated Bottom with double jacket

Condition: new, Year of construction: 2025, Conveyor system for powder products. Stainless steel housing with stainless steel tube. Motor mounted at bottom of machine with screw feeding device. Infeed hopper with 230 liter volume. Capacity 3 to 5 m³/h depending on product. Iiedpfev Nmnnjx Ahyjh Please note that our new prices are often below the usual used prices. Please feel free to inquire and tell us your packaging task. - Usually 30-50 different new machines are available immediately from stock. In addition, we have very short delivery times from approx. 3 weeks for customized machines. Deviations from the sample photo are possible. - All machines are available with full warranty.

Condition: like new (used), Used heatable/coolable stainless steel container Type: STOC3300TPRW Item number: 10844 Volume: Approx. 3300 liters Type: Upright design on three height-adjustable feet Design: Single-walled with thermoplate Material (wetted parts): 1.4301 stainless steel (AISI304) Surface: Satin-finished outside, BA (IIId) inside Internal weld seams: Pickled, passivated and brushed Max. Operating pressure: Atmospheric Max. Operating pressure thermoplate: 1.8 bar Max. Operating temperature: 95°C Top plate: 15° conical bottom Bottom: conical bottom 15° with central outlet DN50 DIN11851 Tank dimensions: Tank diameter: 1600mm Cylinder height: 1500mm Total height: 2430mm Equipment: 1x Ø 500mm manhole cover with swivel bracket on the top, EPDM seal 1x ladder bracket Iisdpfx Ahjuy Ribsysh 1x thermoplate on cylinder H=900mm on cylinder 1x agitator flange connection IEC250 3x spherical caps / height-adjustable feet with foot plates 1x vent valve DN50 stainless steel unpressurized on the top plate 1x DN50 DIN11851 spigot outlet in the center of the underbody 1x DN50 DIN11851 spigot on the top shelf with blind cap 1x DN65 DIN11851 spigot on the top shelf with blind cap 1x type plate

Condition: new, Brand new stainless steel container Article number: 10846 Volume: 550 L Iijdpfx Ahsv Dunfeyoh Type: Standing on a plastic pallet Material (in contact with the media): Stainless steel V2A / AISI 304 Number of fixings: Plastic pallet Bottom: Dished bottom Max. operating pressure: Atmospheric Container dimensions: Inner diameter: 815mm Outer diameter: 890mm Total height: 1330mm Cylindrical height: 1070mm Total width: 890mm Materials: Inside: 14301 / AISI 304 Outside parts: 14301 / AISI 304 Facilities: Nameplate: no Outlet diameter: 50mm Distance from drain to floor: 160mm

Condition: like new (used), Year of construction: 2014, machine/vehicle number: 618, functionality: fully functional, operating hours: 800 h, power: 80 kW (108.77 HP), input voltage: 400 V, input current: 250 A, input frequency: 50 Hz, type of input current: three-phase, temperature: 1,200 °C, inner dimension length: 600 mm, inner dimension width: 400 mm, inner dimension height: 400 mm, total length: 4,900 mm, total width: 2,950 mm, total height: 2,900 mm, overall weight: 10,000 kg, number of chambers: 1, number of shelf rows: 1, control type: PLC-controlled, actuation type: electric, Equipment: CE marking, documentation/manual, Condition: very good; the furnace has only been used for 100 batches. The delivery includes a loading electric cart and three charging baskets. Direct sale to end-users only. W-Technology s.r.o. Polní 8 79201 Bruntál Iedszz A Rrjpfx Ahyjih Czech Republic

Condition: new, Electrically Heated 545L Stainless Steel Agitated Tank Type: EBB500RWP Includes operating manual and CE declaration of conformity. The double jacket is filled with thermal oil, which is heated by an electric heating element. Alternatively available with other agitator types and in different sizes. Volume: 545L Dimensions approx.: Ø 950mm x cylindrical height 880mm Total height: 1120mm plus agitator motor Material: 1.4301 / AISI304 stainless steel Surface finish: Internal and external IIIc/2B Internal weld seams ground Max. operating temperature: 110°C Max. operating pressure: ATM - Vertical design on four legs with forklift tunnel - Top: Hinged lid, central crossbeam with two hinged lid halves - Bottom: Flat bottom with side outlet DN50 DIN11851 and disk valve - 2x side handles - 1x nameplate Propeller agitator for low-viscosity media Power: 0.75KW Speed: 1410RPM Isdow Dy Ddepfx Ahyjih Operating voltage: 3PH 400V