HSM VK 88 + Stadler KF1800

HSM VK 8818

Condition: excellent (used), Year of construction: 2015, operating hours: 20,331 h, functionality: fully functional, pressing force: 100 t, filling opening width: 970 mm, filling opening length: 1,800 mm, bale length: 1,200 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 750 kg, overall weight: 33,000 kg, Good day, We hereby offer you, without obligation, a used, complete baling press line consisting of a baler manufactured by HSM, type VK 8818 R-FU, including conveyor technology and wire tying stations. The following technical data was taken from the manufacturer's operating manual and brochures, for which we cannot guarantee accuracy or completeness. Technical Data – Baler: Manufacturer: HSM GmbH + Co. KG, Germany Type: VK 8818 R-FU Year of manufacture: 2015 Operating hours: 20,331 hours (as of September 2025) Number of bales pressed: 29,020 bales (as of September 2025) Press force (main press): 1000 kN Specific pressing force: 120 N/cm² Shear edge ejector force: 121 kN Feed opening dimensions: 970 x 1,800 mm Theoretical cycle time (idle): 8.3 seconds Theoretical output capacity: 643 m³/hour Bale dimensions: 1,100 x 750 mm, length adjustable from 600 up to 2,000 mm Drive power: 2 x 45 kW, frequency-controlled Connected load: 110 kW Total current consumption: 213 A Fusing: 250 A slow-blow Tying: 5-fold horizontal, fully automatic Output at bulk density: Ljdjyz Af Eepfx Ac Ijab 20 kg/m³: 12.86 t/hour 50 kg/m³: 32.15 t/hour Bale weights (approx. 1.2 m bale length): 650 up to 750 kg per bale, material-dependent Hydraulic oil tank volume: 2000 L HVI 46 PLC control system: Siemens S7-300 Control panel: Siemens TP 700 Baler dimensions (assembled): 12,130 x 4,800 x 3,270 mm (L x W x H) Space requirement (with conveyor): 35,000 x 8,480 x 7,745 mm (L x W x H) Baler weight: approx. 33 t (main press approx. 12 t, press channel with bale clamp approx. 10 t) Additional Optional Equipment Ordered: – Frequency-controlled main drive, 2 x 45 kW, with up to 40% energy savings compared to the standard 2 x 45 kW drive, with same performance – Manual activation/deactivation of the number of wire bindings to save tying wire on non-expansive material – Shear edge ejector with 121 kN pressing force – Sensor-based wire monitoring, with baler shut-off in case of wire breakage or wire end – Bale chute – Optical warning signal, mounted on the control cabinet Condition of the Baler: The complete baling system (baler and conveyor technology) is in good, ready-to-use condition. The unit has been cleaned weekly, lubricated, and maintained according to manufacturer specifications by the operator. Technical Data – Chain Belt Conveyor: Manufacturer: Stadler Anlagenbau GmbH Type: Chain Belt Conveyor KF 1800 Year of manufacture: 2015 Belt speed: 0.36 m/second Feeder belt length: 7,000 mm Inclined belt length: 14,500 mm Gooseneck length: 1,550 mm Incline: 30° Nominal width: 1,800 mm Usable width: 1,638 mm Overall conveyor height: 7,745 mm Pit dimensions for conveyor: 11,200 x 3,000 x 1,250 mm (L x W x H) Scope of Delivery: – HSM VK 8818 R-FU baler – Maintenance platform – Bale chute – Wire diverting stations – Wire spool trolleys (without wire spools) – Stadler KF 1800 chain belt conveyor – Transverse sliding belt conveyor – Pit cover from feed conveyor to pit – Second control cabinet to operate the baler from the conveyor – Machine documentation in English Delivery Time: The complete system has already been dismantled, placed into storage, and can be loaded at short notice following receipt of payment. We would be pleased if this or one of our other balers might be of interest to you. Your Service Team Mertens & Frowein GmbH

Condition: ready for operation (used), Year of construction: 2008, A SIG Corpoplast blow molding machine is available. Output: 21600 bottles/h, bottle formats: 500ml/750ml/1000ml/1500ml, max. blowing air pressure: 40bar, dimensions X/Y/Z: approx. 7000mm/4300mm/3100mm, weight: approx. 20000kg. Including preform feeder Transver AG, year of construction: 2008, silo, elevator, sorting and chute. Documentation available. On-site inspection is possible. Ledst Eu Azspfx Ac Ijab

Condition: excellent (used), Year of construction: 2015, functionality: fully functional, pressing force: 100 t, Technical specifications: Pressing force: 1,000 kN Specific pressing force: 121.2 N/cm² Drive power: 45 + 45 kW, frequency-controlled Voltage/Frequency: 400 V / 50 Hz Idle cycle time: 8.3 s Theoretical idle throughput: 643 m³/h Ljdeygud Aspfx Ac Isab Theoretical capacity at 50 kg/m³: 32.15 t/h Feed opening width x feed opening length: 970 x 1,800 mm Bale width x bale height x bale length: 1,100 x 750 x 600–2,000 mm Bale weight: max. 700 kg or 800 kg, depending on material The baler feed system includes the following components: - 1 fully enclosed STADLER chain conveyor with appropriate shaft covers - 1 support and maintenance platform for conveyor and hopper - 1 STADLER conveyor - 1 automatic channel baler HSM VK8818 R FU (100 t) - 1 wire rack for 500-kg soft wire coils - 10 wire coil trolleys - 1 multi-control system for the baler - Full construction documentation and maintenance history - Serviced and maintained by the manufacturer Commissioning available upon request. Weight: 33,000 kg Tying method: wire Processable materials: plastic film, mixed paper, cardboard, hollow HDPE/LDPE containers, and plastic bottles The system is operational and can be inspected during operation. The machine will be dismantled on 16/02 and can then be inspected at our facility. Immediately available!

Condition: good (used), Year of construction: 2011, operating hours: 40,000 h, functionality: fully functional, pressing force: 88 t, filling opening width: 990 mm, filling opening length: 1,800 mm, bale length: 1,200 mm, bale width: 1,100 mm, bale height: 750 mm, overall weight: 23,000 kg, oil tank capacity: 2,000 l, power: 90 kW (122.37 HP), volume flow: 643 m³/h, Good day, We hereby offer, subject to prior sale, a used baler including conveyor belt, wire tying stations, and bale chute from the manufacturer HSM GmbH + Co. KG, model VK 8818 FU. The following technical specifications were taken from the manufacturer's operating manual and brochures; we do not assume any liability for the correctness or completeness of this information. Manufacturer: HSM GmbH + Co. KG, Germany Lsdpfxoymmtco Ac Ioab Model: VK 8818 FU Year of manufacture: 2011 Operating hours: approx. 40,000 hours as of July 2025 Main press force: 880 kN Specific press force: 107 N/cm² Feed opening dimensions: 990 x 1,800 mm Theoretical throughput: 643 m³/hour Bale dimensions: 1,100 x 750 mm, length adjustable from 600 up to 2,000 mm Drive power: 2 x 45 kW, frequency-controlled Tying: 5-fold horizontal, fully automatic Baler dimensions (set up): 12,130 x 4,800 x 3,270 mm (L x W x H) Overall installation dimensions with conveyor system: 14,000 x 23,000 x 7,745 mm (L x W x H) Note: The machine was used in a recycling facility for compacting paper, cardboard, and film. The press is in good condition and will be replaced with a new, larger press in May/June 2026. Until then, the machine can be inspected in operation with material. We would be pleased if this baler is of interest to you. Your Mertens & Frowein GmbH service team

Condition: new, Year of construction: 2025, Features: - Overband Neodymium Magnetic Separator - HP - Dust suppression - Conveyor belt speed control Lasdpfxow Elbds Ac Ieb - Self-propelled chassis for semi-trailer

Condition: reconditioned (used), Year of construction: 2007, operating hours: 22,605 h, functionality: fully functional, pressing force: 100 t, filling opening width: 1,100 mm, filling opening length: 1,600 mm, bale width: 1,100 mm, bale height: 1,100 mm, bale weight: 1,400 kg, overall weight: 36,000 kg, oil tank capacity: 1,300 l, year of last overhaul: 2025, For sale is a overhauled baler, with 100 tonnes pressing force, large format 1100 x 1100 mm, 75 kW drive power and 10-fold cross binding Technical data baler: Manufacturer Bollegraaf Typ HBC 110 K / 75 kW Year of construction 2007 Press power main press 100 tons Press power of pre-press 50 tons Operating hours 22,605 hours Lsdpfxevf E Avj Ac Ioab Feed channel 1,600 x 1,100 mm Capacity per cycle time 3,15 m³ Theoretic cycle time 19 sec. Bale size 1,100 x 1,100 mm Driving motor 75 kW Connected load 126 kW Full load current 238 A Tying system 5-fold vertical, 5-fold horizontal, fully automated Throughput rate at a bulk weight of 30 kg/cbm approx.16 tons/h bulk weight of 50 kg/cbm approx. 25 tons/h bulk weight of 100 kg/cbm approx. 47 tons/h Bale weight up to 1400 kg, depends on material and bale lenght Volume oil tank approx. 1,300 l SPS controller Telemecanique TSX Micro Operating panel Schneider MAGELIS Touch Baler dimensions built up with hopper 11,750 x 5,000 x 7,105 mm (l x w x h) Transport dimensions only baler 11.750 x 2.500 x 3.450 mm (l x w x h) Machine weight baler approx. 36 tons Comments: The press was partially overhauled and serviced in our workshop and tested and stored after completion of the work. The machine is available at short notice and can be inspected in our warehouse by appointment. The following overhaul work was carried out: Rust removal and partial painting of the press. Remaining hydraulic oil tank drained, oil filter and air filter replaced. New hydraulic oil topped up. All hydraulic hoses replaced. Main hydraulic cylinder, two cylinders of the prepress flap and the cylinder of the press channel dismantled, disassembled, checked, cylinder tubes honed, all seal sets replaced and a final pressure test carried out. Disassembly of the prepress flap with bearings and bearing blocks. 1st and 3rd circular arc segmet cut out and a new one welded in again. Both bearings of the shaft of the prepress flap replaced. Upper material deflector on the frame of the prepress flap replaced. Press ram dismantled, checked and both front rollers replaced. Material deflectors and wear profiles on the sides and base of the press ram cut off and new ones welded in. Horizontal and vertical needle and tying unit dismantled, disassembled, checked, plastic sliding plates, bearings of the drill shafts and wire deflection rollers with bearings in the needle heads replaced. Both bronze slide rails on the left and right in the frame cover to the press ram replaced. Both wire deflection units on the left and right, with bale retaining clamps, completely renewed. Wire insertion unit including hydraulic cylinder under the needle feedthroughs completely renewed. Wire entry marks in the floor and side walls of the bale chamber welded shut and smoothed. General maintenance and service work carried out in accordance with the manufacturer's specifications. Press was tested in manual and automatic mode, accepted and stored after completion of overhaul work. We accept no liability for the technical specifications or any errors.

Condition: used, Year of construction: 1992, Automatic PET bottle blowing machine Lsdpfx Ajwa Rhrjc Ioab Manufacturer: SIDEL Type: SBO 4 S1 Year of prod. 1992 Capacity: 4,000 for 1.5 L / 2 L bottles Installed power: 150 kW Includes 1.5 L molds Preform feeder Technical condition: used machine, starts up, program is functional

Condition: excellent (used), Year of construction: 2014, operating hours: 37,656 h, functionality: fully functional, pressing force: 85 t, filling opening width: 1,500 mm, filling opening length: 1,100 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 650 kg, overall weight: 25,000 kg, oil tank capacity: 1,000 l, year of last overhaul: 2024, volume flow: 410 m³/h, transport width: 2,400 mm, transport length: 9,300 mm, Hello, We are offering you a used baler from the manufacturer Presona AB, type LP 85 VH1, subject to availability. The following technical data was taken from the manufacturer's operating instructions and brochures, for which we cannot guarantee their accuracy or completeness. Manufacturer: Presona AB, Sweden Lajdpjv T I Evefx Ac Isb Type: LP 85 VH1 Year of manufacture: 2014 Total operating hours: 37,565 hours, as of March 2025 Main press force: 85 t Specific press force: 100 N/cm² Pre-press flap force: 28 t Feed chute dimensions: 1,500 x 1,100 mm Filling volume per press cycle: 2.7 m³ Throughput under operating conditions: 410 m³/hour Bale dimensions: 1,100 x 750 mm Drive power: 55 kW Tying system: 5-fold vertical Hydraulic oil tank volume: 1,000 L Press dimensions: 10,350 x 2,400 x 3,150 mm (L x W x H) Press weight: approx. 25 t Note: The machine was used for compaction at a recycling plant. Used for the production of paper, cardboard, films, and plastics such as bottles, buckets, canisters, and drums. The press is in good condition. Many wear parts and entire assemblies have been replaced over the past three years. The machine has been regularly serviced. We would be pleased if this press is of interest to you. Your service team at Mertens & Frowein GmbH

Year of construction: 2012, operating hours: 1 h, condition: used, Transmission: Automatic Laedpfxox R T D Ds Ac Isb Power: 1 kW (1 HP) Empty weight: 20.000 kg Please contact Emal Jaweed for more information

Condition: used, functionality: fully functional, Year of construction: 2008, - Machine in very good technical and visual condition Ledjy Dc Nvjpfx Ac Ijab - Immediately available - Sale includes: - Scrap shear: Zato FCE40 or Genesis GXP400R - Boom - Additional attachments available at extra cost