SECO board 6xRS232 VME-Bus

HOMAG

Condition: not inspected (used), Year of construction: 2005, functionality: unexamined, workpiece height (max.): 40 mm, edge thickness (max.): 3 mm, feed rate X-axis: 35 m/min, rotational speed (max.): 12,000 rpm, number of slots in tool magazine: 48, TECHNICAL DETAILS Gtsdpoyqybuofx Ahvew Panel height min.: 10 mm Panel height max.: 40 mm Edge thickness min.: 0.4 mm Edge thickness max.: 3 mm Feed speed max.: 35 m/min PROCESSING UNITS Pre-milling unit Automatic engagement 48 tool positions End trimming unit 2 motors Fine trimming unit 1 2 motors Motor power: 0.55 kW Speed: 12,000 rpm Fine trimming unit 2 2 motors Motor power: 0.55 kW Speed: 12,000 rpm Edge scraping unit Glue scraping unit Polishing unit 2 motors Spraying device MACHINE DETAILS Control system: PC 22 EQUIPMENT Pressure applied with rubber belt Panel guides with NC positioning Glue pot for EVA hot-melt adhesive Pre-melter for EVA hot-melt adhesive Laser system (Model: LaserTec) Roller set for edge pressing with 5 pressure rollers Units mounted on safety guards CE marking The machine is sold and delivered in its actual and legal condition (“as seen and approved”), based on photo documentation and technical/commercial descriptive documentation. The buyer has the right to inspect the goods prior to collection and assumes responsibility for installation, securing, and use of the machine at the destination. External reference: 5321

Condition: not inspected (used), Year of construction: 2007, functionality: unexamined, working width: 1,935 mm, number of spindles: 40, plate height: 350 mm, working length: 6,200 mm, number of axes: 4, TECHNICAL DETAILS Working area X-axis: 6,200 mm Working area Y-axis: 1,935 mm Maximum panel thickness: 350 mm Gtsdpfx Aheyqx U Hjvsw Number of edge tape magazines: 3 Number of tool positions in tool magazine: 22 (located at the rear of the machine) Drilling spindles Spindles for vertical drilling: 28 Spindles for horizontal drilling in X direction: 4 Spindles for horizontal drilling in Y direction: 8 Total number of vertical + horizontal spindles: 40 Milling spindles Number of controlled axes: 4 Motor power: 10.5 kW Automatic tool changer MACHINE DETAILS Total connected load: 31 kW EQUIPMENT Suction cups for securing the workpiece Safety mats at the front Vacuum pump Waste chip conveyor Fixed groove unit for slotting in X direction The machine is sold and delivered in its actual and legal condition (“as seen and approved”) on the basis of photographic documentation and descriptive technical/commercial documents. The buyer has the right to inspect the item prior to collection and assumes responsibility for installation, securing, and operation of the machine at the place of destination. External reference: 8105

Condition: excellent (used), SINGLE SIDE EDGE BANDER (Left) Edges (band in rolls) thickness (Min/Max) mm 0,3 / 3 Edges thickness in strips / lippings (min/max) mm 0,4 / 20 Panels thickness (min/max) mm 8 / 60 NEW (in 2024) Numerical Control EDGETEQ MOD - Power Touch (WoodCommander) Adjustable Feeding speed up to 25 m/min In-feeding system EZ 14 Spraying unit (Anti-sticking liquid) In-feed fence, adjustable by N.C. Pre-milling Unit (vertical joint trimmers) 2 x Kw 3 Glueing Unit (P.U.R. Glue + Quick Melt system) Band Pressure zone, adjustable by N.C. Edge coils supporting unit (with No. 2 reels) Snipping (end-cutting) unit HL 84 (2 x Kw 0,5 ca.) Pneumatic swivelling and adjustment Rough Trimming unit BF 20 (2 x Kw 1,5 ca.) Gjdpfx Ahjyt Izbovjtw Multi Function Unit (Profile contour Trimming) FK 11 (2 x Kw 0,4 ca.) Profile edge scraping unit Finish processing unit (Glue scraper + Buffing unit) FA 11 Panels Return System "LIGMATECH" Mod. ZHR 541/L/095 (with Portal bridge and 360° rotating vacuum head)

Condition: not inspected (used), Year of construction: 2005, functionality: unexamined, power: 19 kW (25.83 HP), travel distance X-axis: 4,175 mm, travel distance Y-axis: 1,730 mm, number of spindles: 20, number of tool stations in tool turret 1: 18, TECHNICAL DETAILS Working area X-axis: 4,175 mm Working area Y-axis: 1,730 mm Number of suction traverses: 8 Number of tool magazine positions: 18 Spindles Number of spindles for vertical drilling: 17 Number of spindles for horizontal drilling in X-direction: 2 Number of spindles for horizontal drilling in Y-direction: 1 Total number of spindles: 20 Milling Unit Number of controlled axes: 4 Motor power: 18.5 kW Automatic tool changer Liquid-cooled MACHINE DETAILS Total installed power: 19 kW Control model: PC85 EQUIPMENT CE marking Gtsdsyttf Sopfx Ahvjw Front safety guard The machine is sold and delivered in its actual technical and legal condition ('as seen and approved'), based on photographic documentation and technical/commercial documents of a descriptive nature. The buyer has the right to inspect the goods prior to collection and assumes responsibility for installation, securing, and use of the machine at the destination. External reference: 6906

Condition: not inspected (used), Year of construction: 2008, functionality: unexamined, travel distance X-axis: 4,175 mm, travel distance Y-axis: 1,550 mm, workpiece height (max.): 40 mm, number of spindles: 30, travel speed (max.): 80,000 mm/min, TECHNICAL DETAILS Travel range X-axis: 4,175 mm Travel range Y-axis: 1,550 mm Traverse speed X-axis: 80 m/min Traverse speed Y-axis: 80 m/min Traverse speed Z-axis: 30 m/min Maximum workpiece height: 40 mm Number of traverse supports with suction: 8 Spindles Number of spindles for vertical drilling: 20 Number of spindles for horizontal drilling (X-direction): 10 Total number of spindles: 30 Milling unit Number of controlled axes: 4 + Flex5 Motor power: 15 kW Automatic tool changer Liquid-cooled Saw unit Tool magazine 1 Number of tool positions: 18 Tool magazine 2 Number of tool positions: 10 EQUIPMENT NC positioning of suction units Vacuum pump PowerControl P85 control system WoodWop 5.0 machine programming software The machine is sold and delivered in its actual and legal condition ("as is, where is") based on photographic documentation and technical/commercial descriptions of a descriptive nature. The buyer has the right to inspect the goods prior to collection and assumes responsibility for installation, securing, and operation of the machine at the destination. Gtedpfxjyttcwj Ahvow External reference: 7350

Condition: not inspected (used), Year of construction: 2008, functionality: unexamined, edge thickness (max.): 3 mm, feed rate X-axis: 25 m/min, rotational speed (max.): 12,000 rpm, TECHNICAL DETAILS Minimum edge thickness: 0.3 mm Maximum edge thickness: 3 mm Maximum feed speed: 25 m/min MACHINE DETAILS Edge Processing Unit 1 Unit: End Trimming Model: WK13 Number of motors: 2 Motor power: 0.4 kW Max. speed: 12,000 rpm Edge Processing Unit 2 Unit: Top Milling Number of motors: 2 Motor power: 0.55 kW Max. speed: 12,000 rpm Edge Processing Unit 3 Unit: Multifunction Model: FK13 Number of motors: 2 automatic tool changer with NC positioning Motor power: 0.4 kW Max. speed: 12,000 rpm Gsdsytr Hbepfx Ahvotw Edge Processing Unit 4 Unit: Top Mill Model: UF11 Number of motors: 1 Motor power: 4 kW Max. speed: 9,000 rpm Edge Processing Unit 5 Unit: Edge Scraper Model: MN21 with NC positioning Edge Processing Unit 6 Unit: Glue Scraper Model: FA11 Edge Processing Unit 7 Unit: Brush Number of motors: 2 Motor power: 0.25 kW Edge Processing Unit 8 Unit: Brush Number of motors: 2 Motor power: 0.25 kW Total installed power: 35 kW EQUIPMENT Spray unit PowerControl PC22 machine programming software CE marking The machine is sold and delivered in its actual and legal condition ("as seen and approved") based on photographic documentation and descriptive technical/commercial data. The buyer has the right to inspect the goods prior to collection and assumes responsibility for installation, safeguarding, and use of the machine at the destination. External reference: 6216

Condition: ready for operation (used), Year of construction: 2006, Edgebander manufactured in 2006. This HOMAG Optimat KAL 330 features a flexible production layout for furniture parts, accommodating workpiece dimensions from 250 to 3000 mm in length and 120 to 1200 mm in width. It includes a single-sided edge banding machine capable of processing various edge materials up to 20 mm thickness. If you are looking to get high-quality edge processing capabilities, consider the HOMAG Optimat KAL 330 edgebander we have for sale. Contact us for further details. • Line workpiece capacity: • Length 250–3000 mm • Width 120–1200 mm • Thickness 8–60 mm • Edge bander (KAL 330) — base and transport • Continuous machine base; workpiece support with roller bar extendable ~800 mm • Transport chain 80 mm wide with rubber surface; precision guidance, hardened surfaces • Top pressure: driven belt • Technical data: • Feed speed 18–25 m/min • Working height 950 mm • Minimum working width: 55 mm at 22 mm thickness; 100 mm at 60 mm thickness (depending on workpiece length) Gtodpfxeytf Irj Ahvew • Workpiece overhang/supernatant 30 mm • Workpiece thickness 12–60 mm • Edge material from strip: 0.4–20 mm (max cross-section 900 mm²) • Edge material from coil: 0.3–3 mm (max cross-section: PVC 135 mm², veneer 100 mm²) • Max coil diameter 830 mm • Pneumatic connection 7–8 bar • Infeed system and controls (integrated with KAL 330) • Flexible workpiece infeed system wz10 for automatic infeed (lengthwise and crosswise); for precisely sized, square parts • Stepless infeed guidance adjustment (axis), speed set at input terminal • Automatic side adjustment of units (workpiece overhang 30–80 mm) for gluing and post-processing • Input terminal; solvent applicator top/bottom • Edge preparation and gluing • Pre-milling unit: 2 motors, each 4 kW, 150 Hz, 9000 rpm; electro-pneumatic control • Stepless vertical axis SF20 for automatic centering to panel thickness • Pre-melting unit with granule storage • Quick-lock system for QA/QE application unit; QA front glue storage for color change • Basic gluing unit A20; magazine height adjustment ±5 mm (manual spindle) • Extended magazine A6/A-E12/A20 for 2 coils (max Ø 830 mm); preheating station for QA/QE • Automatic pressure zone adjustment • Trimming and milling • Trimming unit HL84 with standing trimming stop for sensitive edges • Pneumatic trimming motor adjustment (2 positions: flush/level and with overhang for contour milling) • Pneumatic chamfer/straight changeover; manual side trimming stop adjustment when edge thickness changes • Rough milling unit: 2 motors stacked, each 1.5 kW, 200 Hz, 12,000 rpm; height adjustment via top pressure • Pneumatic 2-position setting: roughing with ~0.2 mm overhang / without overhang • Reserved free space for a fine milling unit • Contour milling unit Servo FK13 automatic: • 2 motors each 0.4 kW, 200 Hz, 12,000 rpm • Servo-controlled movements; automatic 8-fold tool changer • Feed speed max 20 m/min; minimum spacing between workpieces 500 mm • Workpiece thickness 12–60 mm • Automatic FK adjustment for identical radii on different edge thicknesses; auto retract • FK workpiece guidance with additional clamping for min part length 120 mm (single-sided) • Finishing and cleaning • Multi cleaning unit MN21 automatic: • Up to 3 profiles; tracing from top/bottom/side for chamfer and rounding on pre-milled PVC edges • Electropneumatic air nozzles; automatic chamfer/radius changeover; auto retract of upper/lower tool • Height adjustment via top pressure • PVC shavings separator top/bottom

Condition: ready for operation (used), Year of construction: 2006, This HOMAG KFL 526 / C was manufactured in 2006. A robust double-sided edgebander, it handles workpiece thicknesses from 12 to 40 mm and sizes up to 2500 x 1200 mm. Features include a gluing unit, profile trimming, and a finish unit for precise edge finishing. Ideal for efficient edge banding with speeds up to 35 m/min. Contact us for more information about this machine. Additional equipment • Seperating agent spray device on top/bottom / Double Hogger Longitudinal/Cross: 6.6 kW with electropneumatic control / Gluing Unit A3 - 2 rolls / Profile Trimming Unit FF12 on top/bottom with motors at 12000 rpm / Finish Unit FA11 on top/bottom / Stepless stop cams with maximum cam projection of 25 mm / Standard Trimming Unit SF20 6.6 kW / Rough Trimming Unit 0.55 kW • PUR Nordson Melting Station / Tool Set / Suction Tube Machine Benefits Technical Machine Benefits • Workpiece thickness: 12 - 40 mm / minimum workpiece size (lxw): 250 x 240 mm / maximum workpiece size (lxw): 2500 x 1200 mm / maximum workpiece weight: 50 kg Gjdpfex U Uzrjx Ahvstw • Roller material edge thickness: 0. 4 - 3 mm / maximum edge cross section (plastic): 135 mm² / maximum edge cross section (veneer): 100 mm² / maximum roller diameter: 830 mm • Longitudinal processing speed: up to 35 m/min for thin edge up to 0. 6 mm /up to 30 m/min for thick edge up to 3 mm • Cross processing speed: up to 30 m/min for panel sizing/ up to 20 m/min for edge processing • Minimum workpiece gap: 500 mm

Condition: ready for operation (used), Year of construction: 2009, Edgebander manufactured in 2009. This HOMAG PROFI KAR310/11/A20/S2 features a work piece return system BARBARIC. Consider the opportunity to buy this HOMAG PROFI KAR310/11/A20/S2 edgebander. Contact us for further details. • Condition: Used Additional equipment Gedpfx Aoyhqi Dshvjtw • BARBARIC workpiece return system

Year of construction: 2011, condition: ready for operation (used), Main Drive Number of axis 3 Gtsdpfxex D Nvgo Ahvjw This 3-axis HOMAG WEEKE OPTIMAT BHX 500 was manufactured in 2011. It features a robust CNC processing center with a working area of 2500 mm by 1300 mm, main electrospindle power of 6 KW, and a maximum panel thickness of 80 mm. It includes 84 drilling spindles and dual milling spindles, each offering 6 KW at 18000 rpm. If you are looking to get high-quality CNC capabilities, consider the HOMAG WEEKE OPTIMAT BHX 500 machine we have for sale. Contact us for more information. Application Types CNC Wood Machining