Baling Press

DIXI 40 SLK

Year of construction: 2008, operating hours: 40,000 h, condition: good (used), machine/vehicle number: HBC 140 2x75kW 2008 (00191), Sold by Bollegraaf Recycling Solutions, the original manufacturer of this Bollegraaf baler and conveyor: Bollegraaf HBC140s Baler (2x75kW). Baler: Weight: 47.100 kg Construction year: 2008 Hardox bottom floor plate only Variable channel pressure control Plastic valve Hydraulic pump driven by frequency inverter Anti-rat cabling Oil in-depth filtration Modem Hours 40.000 This baler can also be sold fully refurbished according to the 'Bollegraaf OEM Certified Refurbishment standards'. This includes 2 year guarrantee. Contact us for more information or a quotation. General principles of refurbishment Cleaning & disassembly Dcsdokcgf Hopfx Ab Ter Before the actual refurbishment takes place the baler is completely cleaned and disassembled in our refurbishment workshop. Tolerances After the disassembly the tolerances of all steel components are measured and re-welded where necessary, this at least applies to the following components; • Ram, • Frame, • Channel, • Pre-press-flap After disassembly and inspection the ram is welded-up again and fitted with new ram wheels. The protective grids and the pre-press flap are made dent-free and repaired where necessary. Repainted After measuring the tolerances and any repair- and welding work, all components are being blasted and coated again. Hydraulics: The hydraulic tank is cleaned. The hydraulic lines & hoses are replaced. The hydraulic components are repackaged. The hydraulic oil is replaced. Cabling: All cabling is checked and replaced if necessary. All junction boxes are replaced and placed back in easily accessible positions. Wear parts: All wearing parts are replaced. The pins and shafts of the cylinders and the channel are replaced with new ones. All wearing parts of (both) needle installations and knotters are replaced for new. Cylinders: The cylinders are repackaged and, if necessary, provided with a new chrome layer or a new cylinder rod. MCC Cabinet The switch box is checked and cleaned. If necessary, electronic components are replaced with new ones. The PLC and HMI (human interface) are replaced with the latest Schneider M340 version including the latest software.

Year of construction: 2016, condition: new, functionality: fully functional, HDPE Film washline construction year: 2016 0 working hours (was never in operation) brand: NEUE HERBOLD, D-74889 SINSHEIM consisting of: Wet-granulator type SM 450/600-S5-2 Friction washer type FW 560/3000 Dsdpfx Ajtuui Dob Tscr Conveying screw Floating tank (Floating - sink separation) type TB 500 Mechanical Dryer type TM 1005 Suction Unit type MFT 55/500 Electric control

Condition: ready for operation (used), Model: HSM V-Press 1160 Plus Baler Pressing force (kN): 532 Output (bales/h): 1–2 Max. bale size (mm): 1200x1100x1000–1200 Dimensions (L x W x H) (mm): 1780x1150x2985 Power (kW): 7.5 Year 2007–2008 price €5,500 year 2009–2010 price €5,800 year 2011–2013 price €6,300 We also offer HSM V-Press 1160 Max balers, year 2014–2015 Weight (kg): 2,300 Dcodjra Nyuepfx Ab Tsr ALSO AVAILABLE: 2017–2018 models – €7,500

Condition: used, Year of construction: 2006, Bale size 400x400 mm Force 1 Step 850 KN Force 2 Step 850 KN Force 3 Step 850 KN Steel < 8 to/h Aluminium < 4 kg/h Driving Power 50 KW Arrangement Surface 7,5 x 7,2 m x m Dedpsltinwefx Ab Tocr Machine weight 29 to Press box aperture1,9 x 0,95 mxm Place: Germany Available immediately

Condition: used, machine/vehicle number: 12599, Rotor diameter: 600 mm Rotor width: 1450 mm 12-knife rotor 3 rows stator knives Dedpfxjk N Iy Ne Ab Tocr Inlet cross section approx. 780 x 1490 mm Drive motor: 132 kW

Condition: reconditioned (used), Year of construction: 2005, operating hours: 30,408 h, functionality: fully functional, pressing force: 50 t, filling opening width: 1,100 mm, filling opening length: 1,250 mm, bale width: 1,100 mm, bale height: 720 mm, bale weight: 550 kg, overall weight: 16,000 kg, oil tank capacity: 600 l, year of last overhaul: 2024, Technical data baler: Manufacturer Presona AB Type LP 50 EH1 Year of construction 2005 Operating hours 30,408 hours, as of April Number of pressed bales 198,059 as of April Pressing force main press 50 tonnes Specific pressing force 63 N/cm² Theoretical throughput capacity 530 m³/hour Throughput capacity under operating conditions 260 m³/hour Dimensions of feed chute 1,250 x 1,100 mm Bale chamber volume 2.2 m³ Bale dimensions 1,100 x 720 mm, variable length Drive power 22 kW Tying 5-fold vertical, fully automatic Throughput rates with a bulk density of 30 kg/cbm 6 up to 7 tonnes/hour Bulk weight of 50 kg/cbm 7 up to 9 tonnes/hour Bulk weight of 100 kg/cbm 11 up to 14 tonnes/hour Bale density (paper/newspapers) 400 to 550 kg/m³ Hydraulic oil tank capacity 600 litres PLC control Telemecanique TSX Micro Schneider Magelis control panel Effective transport dimensions excl. baler 8,125 x 2,300 x 3,000 mm (L x W x H) Transport weight press approx. 16 tonnes Condition of the baler: The machine was partial overhauled in our workshop and general maintenance work was carried out. After completion of the overhaul work, the press was tested during operation and is available for sale at short notice. The following overhaul work was carried out: General work: Machine cleaned, derusted, primed, partially painted Wire entry marks in the press channel feed-throughs welded shut and smoothed Hydraulic unit: Dodeu Thhrspfx Ab Tjcr Hydraulic oil tank emptied, tank cleaned, new oil filled Oil filter and air filter replaced Leaky oil sight glass on hydraulic oil tank replaced All hydraulic hoses replaced Electrics: English language installed in the programme menu Two key switches in the control panel replaced Control cabinet replaced Signal lamp on the control cabinet replaced Flaps end switch replaced Electrical system of the turbulator replaced, connected and tested Press ram: All four rollers removed from the press ram and replaced Main hydraulic cylinder dismantled, disassembled and partially overhauled, cylinder tube honed, complete seal set replaced, leak test performed All plastic wear pads on the press ram replaced Pre-press: Both bearings on the pre-press shaft replaced. Both hydraulic cylinders dismantled, disassembled and partially overhauled, both cylinder tubes honed, complete seal sets replaced, leak test performed. Scraper flap on the pre-press replaced. Binding system: Two complete needles with wire deflection rollers replaced Needles adjusted and set All wire deflection rollers in the needle heads replaced Drill fingers replaced Two drill shafts replaced All 8 wear plates on the Drillomat, under the drill fingers, replaced Scope of delivery: Only the baler will be sold. The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: reconditioned (used), Stock - No.: 2553 1 used, partly overhauled and functionally tested Single-Screw Extruder, equipped with: Material hopper loader Extruder BATTENFELD Typ UNI-EX 1-75-25 B Screw - Ø 75 mm – 25 L/D, Cylinder Air-cooled Extruder-Motor 120 kW – DC ( overhauled ) Screw –speed up to 130 r.p.m. additional Temperature controllers for down-stream equipment Control-Board with melt-pressure sensor / Display. Inspectiuon visist / trial-run shortly by appointment in our workshop Wuppertal Germany possible. We can offer, installed to this extruder: Dcodpfx Ajiyyndeb Tsr > screen-pack-changer > pelletizing ( strand, hot-face or waterring ) > other equipment Send us your inquiry. More extruder and complete pelletizing lines ex our workshop Wuppertal, send us your inquiry or visit us, you´re welcome

Year of construction: 2023, condition: new, ‼️BLACK FRIDAY OFFER‼️ RECEIVE A €500 DISCOUNT WHEN YOU COMPLETE YOUR PURCHASE‼️ OFFER VALID UNTIL SATURDAY, 29.11.2025‼️ We have shredders and other recycling machinery in stock in Heilbronn for all types of recycling. From copper recycling to plastic recycling, you can purchase all machines from us. Feel free to inquire. ‼️CAN BE INSPECTED ON SITE‼️ We would be happy to demonstrate the machine to you live in Leingarten! By appointment only! We are based in Heilbronn—a German company, operating under German laws, with warranty and service! We also speak English! Professional copper recovery from cables ranging from 1.5mm to 120mm made easy! ➡️Supplied with accident prevention certification (UVV) from a German company Our cable stripping machine Josan S120! ▶️Weight approx. 236 kg This allows you to recycle cables quickly and cost-effectively and obtain pure copper. Very high processing speed. Powerful 3 kW motor. Built for durability. View detailed images of the machine or inspect it live at our site in Leingarten (by appointment only). Net price: €3,999.00 +19% VAT: €759.81 Gross price: €4,758.81 Since we also do recycling ourselves, we can demonstrate our machines to you by appointment. CE-certified machines from us. ‼️For further questions, please contact us! We can only respond if you provide your name, address, email, and telephone number. Otherwise, your inquiry may be filtered as spam. We will get in touch and provide you with preliminary advice!‼️ Specifications/features/prices subject to change. Errors excepted. Dodpfxep E Einj Ab Tjcr

Year of construction: 2025, condition: new, SEMI AUTOMATIC PASTING MACHINE Dcedognlv Depfx Ab Tor MODEL; MAGRAFKA-100 YEAR; 2025

Year of construction: 2024, operating hours: 10 h, condition: like new (used), Extrusion Line with Densifier – Ideal for Recycling Applications This robust and versatile extrusion line is perfectly suited for recycling polyolefins such as LDPE, HDPE, and PP. Thanks to the integrated densifier, even materials with low bulk density – such as regrind, EPS, film scraps, and other lightweight plastic waste – can be processed efficiently. The densifier compacts the loose material and feeds it directly into the extruder, ensuring a consistent material flow and stable extrusion process even with challenging input materials. Key Features: Dedpfstziudex Ab Tecr • Suitable for all types of polyolefins • Ideal for lightweight, bulky materials like EPS or film regrind • Efficient feeding system via integrated densifier • Compact design and easy maintenance This line is an excellent choice for recyclers, plastic processors, and compounders who require flexibility and reliable performance when working with diverse input materials.