Head carriage for bridge cranes

Demag Tragfähigkeit 3000 kg

Condition: new, capacity 90 degrees: round 350 mm capacity 90 degrees: square 330 mm 500 x 310 band speed 15 - 100 m/min table height 844 mm dimensions of saw-band 4250 x 34 x 1,1 mm total power requirement 2,2 kW weight of the machine ca. 1,2 t dimensions of the machine ca. 1,4 x 2,4 x 1,935 m ACTION PRICE!!! 2-column double miter band saw K-tech DG 50/33 HA-I • 2-column miter saw • Solid, yet easy to use • Material height sensor (automatic cut start detection) Godpfxofg E Hle Ahvotw • Smooth running thanks to bevel cut, feed controller + cutting pressure controller • Massive material infeed roller • Removable chip tray (disinfection) • Energy-saving and low-vibration thanks to bevel cut • Ergonomic, safe and free-standing control panel • Frequency-controlled saw drive 15 -100 m/min. • Hydraulic cutting pressure control valve • Hydraulic control of saw frame and vice • LEDs for monitoring all safety functions • Large dimensioned wheels (520 mm) a. • Clear miter setting up to 60° Semi-automatic function: 1. Clamp material 2. Saw starts 3. Rapid lowering to the start of the material or the same for series cutting cut 4. Saw band off 5. Raise the frame to just above the material 6. Open the vise

Condition: good (used), Year of construction: 1990, RANDEK SP700 cut saw Godpfx Aoh Ayyqohvstw manufacture Randek Sweden Year 1990 in good condition Randek’s SP700 series provides reliable cut saws that are a major asset to roof truss and house producers around the world. The SP700 cut saw is effective, easy-to-use and accurate. It has been on the market for a long time and is continuously improved in close contact with our many customers. The blade on this semi-automatic saw supports angled cuts, which mean it can make any cuts you may require. You can also use the large diameter blade (700mm ) to cut several sections of stacked timber simultaneously. • Angled cuts from 0° to 360° • Cut heights up to 250 mm, possible to cut three boards each cutting cycle • PLC programmable saw • Fixation of timber near the cutting area resulting in accurate cutting roller conveyor system with 5 adjusteable pneumatic stoppers . Lenght 6,25m outfeeding roller conveyor 4,10m Complete line: 11,5m technical inforamtion under subjet of correction

Condition: used, Year of construction: 1994, The emergency power generator was rarely used; it was connected to the heating system, which is why it does not have a water cooler. There are a total of 2 units available; the price is for 1 unit. Godpfsxdc Ehsx Ahvetw

Condition: ready for operation (used), Year of construction: 2008, • Glass thickness (mm): up to 30 Gjdpfsxgtqgsx Ahvotw • Glass height (mm): up to 2000 • Cleaning brushes: 4 front and 4 rear

Condition: excellent (used), Year of construction: 2006, Urban SV 530 + WT 530 Gedowrpxtopfx Ahvjtw The machine has undergone a professional mechanical service. Ready for work.I will send a video of the machine working on whatsapp.

Condition: excellent (used), Year of construction: 2018, operating hours: 100 h, We specialize in the remanufacturing of blowers, compressors, and vacuum pumps. We service equipment from manufacturers such as: Aerzen, Kaeser, Atlas Copco, Robuschi, Busch, and Tuthill. We also offer blowers and compressors for rental. We operate throughout Europe and beyond. Gtedpfx Aon Tntqohvow

Condition: good (used), Year of construction: 1994, 2 side planer top - bottom constant table ( always same infeed height ) max. planing width 600 mm Gtjdpfx Ahehuthyjvew max. planing height 280 mm planing shafts with strip knives immediately ready for use

Condition: good (used), Year of construction: 2013, overall weight: 1,519 kg, power: 75 kW (101.97 HP), volume flow: 14.85 m³/h, pressure (max.): 12.8 bar, Air Compressor Atlas Copco GA75VSD FF Technical Data Manufacturer: Atlas Copco Airpower Model: GA75VSD FF Year of manufacture: 2013 Maximum pressure: 12.8 bar Free air delivery: 14.85 m³/min Motor power: 75 kW Motor speed: 3,000 rpm Weight: 1,519 kg Power supply: 400 V 50 Hz 3 phase Design: Oil-injected screw compressor Control: Electronic control panel Gjdpoxk U Alsfx Ahvjtw Origin: Made in Belgium No liability is accepted for the correctness, completeness, or up-to-dateness of the information provided.

Condition: good (used), Year of construction: 1994, Molecular filling system / diagonal filling Gjdeir Efuspfx Ahvotw weight 520 kg

Condition: ready for operation (used), Year of construction: 1996, pressure 80.0 t chamfer lenght 2550 mm distance between columns 2130 mm column arm 420 mm ajustment speed 100 mm/sec working feed 10.0 mm/sec return speed 80.0 mm/sec stroke 200 mm dayligth 470 mm table width 60.0 mm table height 910 mm Number of working hours ca. 37.102 h total power requirement 9.0 KW weight of the machine ca. 5750 kg range L-W-H 3100 x 2180 x 2540 mm good / well-maintained condition (!!) - Inspected condition - Machine video - ?v=fwdjSiQYq_A Equipment: - CNC electro-hydraulic press brake Gjdpfx Aexabnyshvotw - OPERATEUR CNC control for 8 axes X1 + X2, Y1 + Y2, R1 + R2, Z1 + Z2 - CNC-controlled backgauge adjustment (X-axes) - CNC-controlled vertical adjustment of the stop fingers (R-axes) - CNC-controlled left-right adjustment of the stop fingers (Z-axes) - Freely movable two-hand control & foot switch - Tool crowning - AMADA type - Various tools - CE marking - Side guards (hinged doors) - Rear guards (hinged door) - 2x emergency stop buttons at the front - Operating instructions