Rotary compactor and 2 x skip containers

de Rooij 16 cu metre closed skips and compactor.

Condition: excellent (used), Year of construction: 2007, operating hours: 21,676 h, functionality: fully functional, pressing force: 78 t, filling opening width: 750 mm, filling opening length: 1,500 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 600 kg, overall weight: 25,000 kg, transport height: 3,000 mm, oil tank capacity: 1,000 l, power: 55 kW (74.78 HP), empty load weight: 25,000 kg, volume flow: 930 m³/h, operating pressure: 250 bar, How do you do? We are pleased to offer you a used baler of the manufacturer Presona AB, type LP 80 VH1. The following technical data was taken from the manufacturer's operating instructions and brochures, for which we cannot accept any liability for correctness and completeness. Manufacturer Presona AB, Sweden Type LP 80 VH1 Year of manufacture 2007 Total operating hours, 21,676 hours, as of November 2024 Cpjdpfx Aaovgrh Uo Esw Main press force 78 t Specific pressing force 95 N/cm² Pressing force of prepress flap 28 t Dimensions of feed chute 1,500 x 1,100 mm Filling volume / pressing cycle 2.7 m³ Throughput capacity under operating conditions 410 m³/hour Bale dimensions 1,100 x 750 mm Drive power 55 kW Tying 5-fold vertical Hydraulic oil tank volume 1,000 L Baler dimensions assembled with hopper 10,985 x 3,750 x 4,310 mm (L x W x H) Machine weight press approx. 25 t Note: The machine was used by a recycling company to compact paper, cardboard and film. The press is in good condition, in operation until January 2025 and can be inspected by appointment. We would be delighted if this machine is of interest to you. Your service team Mertens & Frowein GmbH

Condition: good (used), Year of construction: 2009, functionality: fully functional, Weight 4950 kg, total weight 12000 kg Cjdpfxowpmcks Aa Eopw 5.5 kW

Condition: excellent (used), Year of construction: 2006, operating hours: 2,632 h, functionality: fully functional, machine/vehicle number: 29.381, pressing force: 35 t, filling opening width: 620 mm, filling opening length: 1,000 mm, total width: 2,380 mm, total height: 2,500 mm, total length: 6,625 mm, Including feed belt. The machine is immediately ready for operation. Cedovaw T Aopfx Aa Ejpw

Condition: as good as new (ex-display), Year of construction: 2025, operating hours: 25 h, functionality: fully functional, Equipment: rotational speed infinitely variable, Crusher Equipment Including: Special tools, reinforced, 7/7 tool carriers with 4 tools each (tools consist of main, pre-crushing, and post-crushing blades) Shaft speed individually and infinitely adjustable, approx. 0–41 rpm Including post-crushing bar Including tilting skip Drive Unit Drive power: 294 kW Including Scania diesel engine, Stage 5 Including standard noise reduction package Including Power RAM pre-cleaner Including central lubrication for the 4 main bearings Including Cleanfix Including swiveling cooler Electrics / Controls Including IFM display Including radio remote control Including four shredding programs (wood, waste, special, and green waste) Discharge Conveyor Including discharge conveyor Cjdpfxeu Hgllo Aa Eopw Custom Equipment Including preliminary armoring of tools Including overband magnet, hydraulically height adjustable – neodymium – Including hopper extension on 3 sides, approx. 800 mm each Including electric pump for hydraulic oil Including GPS module Including rubber tracks Including pressure sensors Including additional noise-reducing cassette (-10 dB(A)) Refurbishment / Service Refurbishment and service by HAAS

Condition: used, 3-axle truck trailer, low-loader trailer MÜLLER MITTELTAL Type AZP Curtain-sided low loader, low-loader trailer, low loader for machine transport First registration: 2001 Total mileage: approx. 350,000 km Gross vehicle weight: 24,000 kg Unladen weight: 5,500 kg Payload: 18,500 kg Platform height: 840 mm Loading height under tarpaulin frame: 3,200 mm Cedpfx Aot N Antea Espw Platform length: 7,450 mm Overall length: 9,150 mm Overall width: 2,550 mm Overall height: approx. 4,050 mm Axle load front: 8,000 kg Axle load middle: 8,000 kg Axle load rear: 8,000 kg Tyres: Michelin 215 / 75 R17.5 (135/133J XTE 2+ TL) - Rear wing doors at drop side height - Tarpaulin frame with EDSCHA roof system - Tarpaulin frame designed for easy removal (can also be used with the frame removed and the tarp pushed forward) - Spare wheel mounted on the front wall - Independent lifting and lowering of front and rear axles - Middle axle with lift function - Drawbar – extendable in multiple stages - Heavy-duty lashing rings on the outer frame and in the vehicle centre - ALU drive-on ramps, length 268 cm, width 410 mm, height 130 mm (surcharge EUR 2,000 net) The trailer was purchased new by us and is therefore first-hand. The trailer has been deregistered since 2025.

Condition: ready for operation (used), Hsm HL 4809 LI baler Cedpfora Dddsx Aa Espw - Large filling opening, ideal for big boxes - Container tipper for convenient filling Pressing force in kN: 480 - Voltage/frequency: 3 x 400 V / 50 Hz - Bale weight in kg (depending on material): up to 400 kg - Bale dimensions (length x width x height in mm): 1200 x 1100 x 750 - Machine dimensions (length x width x height in mm): 5648 x 1849 x 2515 Idle cycle time in seconds: 53 - Manual tying: 4 times with wire

Condition: reconditioned (used), Year of construction: 2001, functionality: fully functional, machine/vehicle number: HBC 140 2x75kW 2001 (210-008-01), pressing force: 155 t, bale weight: 1,500 kg, pressure: 250 bar, power: 150 kW (203.94 HP), year of last overhaul: 2024, Equipment: documentation/manual, Sold by Bollegraaf Recycling Solutions, the original manufacturer of this Bollegraaf baler and conveyor: Bollegraaf HBC140s Baler (2x75kW). Baler: Weight: 47.100 kg Construction year: 2008 Hardox bottom floor plate only Variable channel pressure control Plastic valve Hydraulic pump driven by frequency inverter Anti-rat cabling Oil in-depth filtration Modem Hours 40.000 This baler can also be sold fully refurbished according to the 'Bollegraaf OEM Certified Refurbishment standards'. This includes 2 year guarrantee. Contact us for more information or a quotation. General principles of refurbishment Cleaning & disassembly Before the actual refurbishment takes place the baler is completely cleaned and disassembled in our refurbishment workshop. Tolerances After the disassembly the tolerances of all steel components are measured and re-welded where necessary, this at least applies to the following components; • Ram, • Frame, • Channel, • Pre-press-flap After disassembly and inspection the ram is welded-up again and fitted with new ram wheels. The protective grids and the pre-press flap are made dent-free and repaired where necessary. Repainted After measuring the tolerances and any repair- and welding work, all components are being blasted and coated again. Hydraulics: The hydraulic tank is cleaned. The hydraulic lines & hoses are replaced. The hydraulic components are repackaged. The hydraulic oil is replaced. Cabling: All cabling is checked and replaced if necessary. All junction boxes are replaced and placed back in easily accessible positions. Wear parts: All wearing parts are replaced. The pins and shafts of the cylinders and the channel are replaced with new ones. All wearing parts of (both) needle installations and knotters are replaced for new. Cylinders: The cylinders are repackaged and, if necessary, provided with a new chrome layer or a new cylinder rod. MCC Cabinet The switch box is checked and cleaned. If necessary, electronic components are replaced with new ones. Cjdotvau Aepfx Aa Espw The PLC and HMI (human interface) are replaced with the latest Schneider M340 version including the latest software.

Condition: new, Year of construction: 2023, machine/vehicle number: 7YXXX, VIS G is the ideal and the most efficent solution for serap processing like stampings, trimmings, wires mostly recommended for the automotive industry, metal recyclers and non-ferrous metal remelting industry. Cpedpfx Aaomqi Ako Ejw

Condition: ready for operation (used), Technical specifications of Dixi 60 AUTOMAT baler Filling opening (W x H): 1550 x 1000 mm Drive power: 31.5 kW Pressing force: 60 t Bale weight (depending on material): 350–600 kg Bale dimensions (W x H x D, adjustable): 1100 x 800 x 300–1600 mm Cpjdpfx Aaev Amw Nj Esw Pressing/cycle time: 13/24 s Machine weight: 7000 kg

Condition: used, Year of construction: 2018, operating hours: 3,977 h, functionality: fully functional, Morbark Woodhog 3400XT 3,977 hours In good condition with transport dolly Cpsdpfx Aswlzdzja Eow Location: Belgium