Roller conveyor curve, roller conveyor curve

Costo

Condition: excellent (used), FULL LINE of 4 Side Sizing-Milling & Edge Banding (also SOFTFORMING), through-feed drilling and splitting of panels. Complete with fast automatic handling. Composed of the following machines: A) Loader (Bridge-Frame) "RBO (BIESSE)" Mod. Winner C (1) B) 1st Double-side Sizing & Edge Bander "BIESSE" Mod. Stream SB1 11.0 Softforming C) 1st 90° Turning device (Lengthwise to Crosswise) "RBO (BIESSE)" Mod. GPK-1 D) 2nd Double-side Sizing & Edge Bander "BIESSE" Mod. Stream SB 2 9.5 Blodettgy Hopfx Ab Tsr E) 2nd 90° Turning device "RBO (BIESSE)" Mod. GPK-2 (straight or Crosswise to Lengthwise) F) Multi-Borer with CN "BIESSE" Mod. Techno FDT CN (with 2 horizontal working units, 6 vertical bottom working units and 3 vertical top working units) G) Multi-Borer with CN "BIESSE" Mod. Techno FDT CN (with 2 horizontal working units, 6 vertical bottom working units and 3 vertical top working units) H) 3rd 90° Turning device "RBO (BIESSE)" Mod. GPK-3 (straight or Crosswise to Lengthwise) I) Splitting Saw (Splitter) Lengthwise "GM (for BIESSE)" Mod. Split 4-84 LT L) Stacker (Bridge-Frame) "RBO (BIESSE)" Mod. Winner SC (2)

Condition: excellent (used), Double-side Sizing-Milling & Edge Banding - First (1st) machine in a line Edges (tape) thickness in rolls (min/max) mm 3 Edges thickness in stips / lippings max mm 1,3 Panels thickness (min/max) mm 10 / 45 Working width (min/max) mm 270 / mm 1300 Bodofi Tkgopfx Ab Tslr Numerical Control /Software ICOS open Adjustable feeding speed (m/min ) 10 - 50 Without Transmission bar (Master & Slave system) Top pressure system with rubber belt SIZING PART (for each side): Pre-milling Unit (vertical joint trimmers) 75.30 (Kw 6,6 x 1) EDGE-BANDING PART (for each side): Glueing Unit (P.U.R. Glue + Quick Melt system) 04.1569 + 283.205 Pressing roller (revolver) both for straight and shaped edges (softforming) mm 1.050 Edge coils supporting unit (reels N°) 6 Snipping (end-cutting) unit 08.42 (Kw 0,2 x 2) 40 m/min Rough Trimming unit 08.055 (Kw 0,66 x 2) 0°-30° Fine Trimming unit 08.0582 (Kw 0,66 x 2) 0°-30° Glue scraping unit 08.50 Buffing unit 08.617-2 (Kw 0,18 x 2)

Condition: excellent (used), LOADER (BRIDGE-FRAME) WITH DOUBLE PICK-UP STATION Gantry (Portal) machine, belonging to the line (SOFIT code: J10039) Vacuum system (with its pump) Blodpfx Abjl Hycwe Tjr N. 2 Vertical supporting columns of the top supporting beam N. 1 Horizontal top supporting beam (where the carriage slide on) N. 1 Motorized sliding carriage with horizontal metal arms N. 2 Horizontal metal arms with vacuum cups, adjustables N. 2 Out-side rollers ways (on gound) to in-feed pile of panels to the Loader N. 1 Out-side motorized rollers table (which in-feed the panels to the Unloader) Separate electric and command panel Electronic Programmer PLC MAGELIS Perimetral safety metal grids Working capacity (cycles/min) 10 (ca.) Min/Max panels thickness mm 10 - 60 (ca.) Min dimensions of the panels mm (ca.) Max dimensions of the panels mm 1200 x 3200 (ca.) Total installed motor power Kw

Condition: used, Year of construction: 2003, SCM SANDYA 20 model 20 M3 135 calibrating and sanding machine, used Year of manufacture: 2003 Serial number: AE/024903 Maximum working width: 1350 mm Feed speed: 3.5-18 m/min with inverter Working height: 4-170 mm Vacuum bed: 7.5 KW Configuration: 1st group: grooved steel calibration roller D. 250 – motor 22 KW 2nd group: sanding roller D. 250, hardness 45 SH – two-speed motor 9/11 KW, 1400/2800 rpm 3rd group: combined roller D. 170, hardness 30 SH + segmented elastic pad (46 segments) – motor 11 KW with inverter 4th group: scotch brite finishing roller Bed positioner with workpiece Blodexwbydjpfx Ab Tsr Belt size: 2620 x 1370 mm Blowers for 2nd and 3rd belt Automatic belt centering Electronic control of 1st / 2nd / 3rd roller / pad

Condition: excellent (used), UNLOADER (BRIDGE-FRAME) WITH DOUBLE STORAGE STATION Gantry (Portal) machine, belonging to the line (SOFIT code: JZ1030) Vacuum system (with its pump) N. 2 Vertical supporting columns of the top supporting beam N. 1 Horizontal top supporting beam (where the carriage slide on) N. 1 Motorized sliding carriage with horizontal metal arms N. 2 Horizontal metal arm with vacuum cups, adjustables N. 2 Out-side rollers way (on gound) to out-feed pile of panels from the Unloader N. 1 Out-side motorized rollers table (which brings panels to the Unloader) Bedpfxel Hyfco Ab Tjlr Separate electric and command panel Electronic Programmer PLC MAGELIS Perimetral safety metal grids Working capacity (cycles/min) 10 (ca.) Min/Max panels thickness mm 10 - 60 (ca.) Min dimensions of the panels mm (ca.) Max dimensions of the panels mm 1200 x 3200 (ca.) Total installed motor power Kw

Condition: good (used), Costo roller conveyor 2 meters with drive Manufacturer: Costo Type: roller conveyor application: Conveyor systems length: 2 meters roll width: 44 cm web width: 50 cm Lateral guidance left and right With drive Further conveyor systems, roller conveyors, belt conveyors and roller conveyors - you will find them in our store! Bjdpfef Ehxtex Ab Tolr International shipping costs on request!

Condition: excellent (used), Double side - Independent Machine (or 1st and/or 2nd in a line) Edges (tape) thickness in rolls (min/max) mm 0,3 / 3 Edges thickness in stips / lippings (min/max) max mm 1,0 Panels thickness (min/max) mm 8 / 45 (60) Working width (min/max) mm 236 (266) / 3300 Numerical Control / Software ICOS Open (Windows base) Adjustable feeding speed (m/min ) 10 - 50 Safety and sound-proof enclosures/cabins SIZING PART (for each side): Anti-chipping Milling Unit 75.186 (1 x Kw 4,4) Hogging Units (2 x Kw 6,6) Free space EDGE-BANDING PART (for each side): Lamps to heat the workpieces side Glueing Unit (Hot Melt glue) 04.1570 Pressure zone Edge coils supporting unit (No. of reels) 2 Snipping (end-cutting) unit 08.42 (2 x Kw 0,66) 30 m/min (0°-25°) Rough Trimming unit 08.0555 (1 x Kw 0,66) Multi Function Unit (Profile contour Trimming unit) MFA 08.342 (2 x Kw 0,66) SERVO - 20m/min Bedpfx Abowz Ic Ao Telr Profile Scraping unit 08.519 Glue scraping unit 08.50 Buffing unit 08.617-2 (2 x Kw 0,18) Milling grooving unit: 75.30 (2 x Kw 4,4)

Year of construction: 1990, condition: excellent (used), I sell the turning device HOMAG TD31/25/13. Year 1990. One side feeding suitable for line. Element width 1250 + 1250mm Total length 6500mm Available immediately. Ready for work, possible to test. With full manuals. Bsdpfxjktfvfo Ab Tslr

Condition: good (used), Costo pusher for conveyor systems Bjdpsfykudsfx Ab Tslr Manufacturer: Costo Type: pusher pusher application: Conveyor systems Scope of delivery: 1 pusher Shipment via forwarding agency possible, please contact us. More articles - new and used - you will find in our store! International shipping costs on request!

Condition: excellent (used), Year of construction: 2010, functionality: fully functional, workpiece height (max.): 60 mm, edge thickness (max.): 20 mm, workpiece width (max.): 60 mm, The machine has been serviced and is in excellent condition. It is immediately ready for operation! TECHNICAL DETAILS - Edge thickness (glued): max. 20 mm - Maximum gluing height: 60 mm - Maximum roll material thickness: 3 mm - Piece width: min. 60 mm - Maximum feed rate: up to 25 m/min - Feed: continuous - Electric height adjustment: available Blodpjxg Ix Sefx Ab Tor - Pressure system: upper belt pressure - Preheating zone: available - Granulate glue system: with pre-fabricated container - Glue pot: interchangeable/variable - Spray unit: available - Pre-milling unit: available - Trimming unit: with 2 motors - Milling stations: flush/radial/chamfer, 1 available - Corner rounding unit: with 2 motors - Edge scraper: profile and planer - Buffing unit: available - Strip magazine: available - Units: synchronized units with NC axis/axes - Machine version: left hand side - Quick-change units: available MACHINE DETAILS - Remote control: PowerControl PC 22 - Weight: 5,000 kg - Machine length: 7,845 mm - Standards: CE requirements EQUIPMENT - Special equipment: with nesting - New chains - HOMAG feed device with 2 rollers - HOMAG A 20 glue unit - HOMAG HL 84 - HOMAG FK 11 - HOMAG PN 10 profile pull scrape unit - HOMAG FA 11 finishing unit