Conical twin-screw extruder

Cincinnati Titan 45R-APC

Year of construction: 2001, operating hours: 64,499 h, condition: good (used), Conical screws, approx. 110 kg/h. A.C. motor 30.0 kW. New motor, 64,499 operating hours. Giedpfx Aew Hy Uuogbsl

Condition: as good as new (ex-display), Year of construction: 2023, The ENR series are air-cooled chillers for industrial use for outdoor installation. The ENR 038 has axial fans, scroll compressors, condensers with finned aluminum fins and self-cleaning coaxial evaporator for maximum reliability. Internal pump, tank, fan control, low GWP refrigerant R454B. Refrigerating capacity 37 Kw, envious GWP refrigerant R454B Gjdpfx Agsfmd Hhebeil We have a lot of chillers directly from stock available used and new . contact us for a no obligation quote. We rent / sell / and also take over the service for all refrigeration systems Germany-wide.

Condition: reconditioned (used), Stock - No.: 2553 1 used, partly overhauled and functionally tested Single-Screw Extruder, equipped with: Material hopper loader Extruder BATTENFELD Typ UNI-EX 1-75-25 B Screw - Ø 75 mm – 25 L/D, Cylinder Air-cooled Extruder-Motor 120 kW – DC ( overhauled ) Screw –speed up to 130 r.p.m. additional Temperature controllers for down-stream equipment Control-Board with melt-pressure sensor / Display. Inspectiuon visist / trial-run shortly by appointment in our workshop Wuppertal Germany possible. We can offer, installed to this extruder: > screen-pack-changer > pelletizing ( strand, hot-face or waterring ) > other equipment Send us your inquiry. Gjdjiyyndepfx Agboil More extruder and complete pelletizing lines ex our workshop Wuppertal, send us your inquiry or visit us, you´re welcome

Condition: excellent (used), Year of construction: 2015, functionality: fully functional, machine/vehicle number: 3.04-00054, Equipment: type plate available, Used Bellaform extruder Type: BH45-30D Year of manufacture: 2013 With screw dimensions 45 mm - 30 l/d, screw speed approx. 160 rpm With 30 kW water-cooled servo motor, with gearbox Cylinder with 4 heating/cooling zones and water bushing in the feed area Material hopper plus a COLORTRONIC dosing screw for masterbatch A melt pressure sensor Control cabinet integrated into the machine frame, with factory-new PLC and With new touch panel for simple and intuitive operation This extruder has been functionally tested! Giodpfeuxa Abjx Agbjl Dimensions: approx. 195 x 70 x 200 cm (L x W x H with hopper)

Condition: good (used), Year of construction: 2002, Manufacturer: BRÜCK Tip: 12/1600 Load capacity: 12000 kg Max sheet width: 1600mm Coil diameter: 1800mm Weight : cca 14 t Without control cabinet! Giedehrnbkepfx Agbjl

Year of construction: 1999, condition: used, Seocnd hand Entex Extruder PL- WE 100 complete with electrical cabinet. Wa in operation for Powder Coatings. Godpfxobqt Aro Agboil For sell is also a Entex Extruder PL WE 70 ( Laboratory ). Photos on request.

Year of construction: 2001, condition: excellent (used), Single screw extruder WEBER NE5 1-30:D with 2 co-extr. WEBER ZE30 Year of construction 2001 Screw diameter 50 mm Application:PE-PP, Three-layer pipes or pipes with colored stripes The plant has manufactured heating pipes Condition: very good Giodpfx Agohy Tp Dobjl 2 Co-Extruders WEBER ZE30 Screw diameter 30mm The three-layer pipe system is my property Location: Sachal EXTRUSIONSMACHINEN D-26345 Bockhorn/Grabstede, Germany

Year of construction: 2024, condition: new, noris- Extruder MINI ESE 20/25 D Technical data Screw diameter [mm] 20 Screw length [L/D] 25 Gjdpfx Agehx Elfobsil Screw speed [min-1] 20-200 min -1 Screw axial pressure [bar] 300 Continuous load 350 maximum Drive Three-phase drive with frequency converter Drive power [kW] max. 2.5 Reduction gear with integrated axial bearing Weight [kg] approx. 160 Dimensions [Lx Wx H] [mm] approx. 1050 x 600x 1590 *) Electrical connection values 3 / N / PE Supply voltage [V] 400 at 50 Hz Control voltage [V] 230 Temperature control electrical resistance heating bands in mica design. Max. processing temperature [°C] 300 Switch cabinet and control panel The electrical installation of the extruder is located in the machine base. The base contains all the necessary switching, control and display devices. The feed zone is water-cooled, the water connection is provided by the customer, a cooling unit for cooling the water is not included in the offer. Extruder tools are not part of the offer

Year of construction: 1971, condition: good (used), decoiler - expansion mandrel with coil lifting table strip width: 1.200 mm Giedpfx Agsd Ha E Sobel strip thickness: 0,3 - 5 mm coil weight: 10 t mandrel Ø: 508 mm

Year of construction: 2000, condition: used, Rotational speed: 227/min, power: 31kW, heating output: 7.8kW, length: 1952mm, width: 840mm, height: 1920mm, weight: 820kg. Giododuyyzopfx Agbjl