CNC Machining Centre for Door Frames

Centauro Alfa Jamb

Condition: used, Year of construction: 2014, power capacity 3 kW feed pressure 7 bar liter capacity / l weight 286 kg Chicago Pneumatic CPVR15 CE screw compressor - Year of manufacture 2014 The CPVR15 CE impresses with its robust design, long service life and low operating costs. Whether in workshops, workshops or industrial applications - this compressor reliably supplies you with the compressed air you need. Drive power: 3 kW Delivery pressure: 7 bar Air output: up to 58 CFM (approx. 1,640 l/min) at 7 bar Weight: 286 kg Dimensions: approx. 965 mm (L) × 620 mm (W) × 1,040 mm (H) Operating noise: approx. 50-58 dB(A) Voltage/frequency: 415 V / 50 Hz Nedpfx Ash A Sfdehvjcn Application: Workshops, craft businesses, industrial applications with medium compressed air requirements Included in delivery: 1x compressor - Chicago Pneumatic CPVR15 CE 1x refrigeration dryer - OMI ESD 108 - 0.70kW 1x Beko Öwamat 2 - oil-water separator Technical data was taken from publicly available sources

Condition: refurbished (used), SCHLATTER Welded wire mesh production line MG24 Full revamped WORKING RANGE Panel width: max. 2500 mm Weft wire length: min. 900 mm Weft wire length with QF5 dispenser: min. 300 - 1600 mm Spacing between extreme warp wires: max. 2400 mm Mesh length (warp wire length): max. 2500 - 6000 mm Spacing between warp wires: min. 100 mm Spacing between weft wires: 25-250 mm Adjustable by cutting device (0-1) Warp wire diameter: 4.0 - 12.0 mm Weft wire diameter: 4.0 - 12.0 mm Number of warp wires: max. 24 WELDING MESH MACHINE MG 24.1/8C, Basic equipment including: - 1 Machine frame - 1 Upper support for press reception, continuously adjustable by hand crank - 1 Magnet supports with retaining magnets and weft wire monitoring. - 1 Row of pneumatic solenoid valves for press actuation. - 1 Installation for air and water. - 2 Pneumatic rotary drives with oil damping - Static motor torque with 5 bar compressed air: 480 Nm - Front continuously adjustable from: 25 - 250 mm adjustable by cutting device (0-1) - 1 Advance carriage with panel lifting device - 1 Set of tools for machine adjustment WELDING SECTION 8 Type C Transformers Rated power of each transformer: 100 kVA No-load secondary voltage: 7.1 V Rated secondary current: 14 kA 8 Thyristor contactors ES 130 12 Welding presses: 5.0 kN 12 Chain current bridge for spacing of warp wires: 50-100 mm 12 Chain current bridge for spacing of warp wires (for offset warp wires): 100 mm 10 Chain current bridge for spacing of warp wires: 100-150 mm 8 Chain current bridge for spacing of warp wires (for offset warp wires): 150 mm 6 Chain current bridge for spacing of warp wires: 150 - 200 mm 6 Chain current bridge for spacing of warp wires (for offset warp wires): 200 mm 24 Lower electrode holders Cu with standard angled electrodes and each with a water-cooled current cable, width: 58 mm 24 Wire clamping pliers Panel width: max. 2500 mm Weft wire length: min. 900 mm Weft wire length with QF5 dispenser: min. 300 - 1600 mm Spacing between extreme warp wires: max. 2400 mm Mesh length (warp wire length): max. 2500 - 6000 mm Spacing between warp wires: min. 100 mm Spacing between weft wires: 25-250 mm Warp wire diameter: 4.0 - 12.0 mm Ncodswu Tu Dopfx Ahvsn Weft wire diameter: 4.0 - 12.0 mm Number of warp wires: max. 24

Condition: excellent (used), Independent machine (standing alone) and/or Universal machine (First & Second in a line) Electronic Programmer EasyLing Safety and sound-proof enclosure No. 3+3 Vertical columns to support the working units Min. useful working width (mm) 240 Max. useful working width (mm) 3100 Njdpswhmdfsfx Ahvscn Min. useful working tickness (mm) 3 Max. useful working tickness (mm) 150 Distance between center-axes of the disappearing dogs (mm) 800 Adjustable (min/max) feeding speed (m/min) 4 - 24 Total installed power No. 4 Working groups (for each machine's side): Scoring Unit Jumping Scoring Unit 1 x Kw 3 (RPM 6000) Hogging Unit 1 x Kw 6 (RPM 6000) 0-10° Jumping Milling Unit 1 x Kw 6 (RPM 6000) 0°-90° Milling-Shaping unit 1 x Kw 6 (RPM 6000) 0°-90°

Condition: good (used), functionality: fully functional, We offer for sale a complete line for multi-point automatic welding of SCHLATTER brand steel wires. We have three fully operational production lines. There are also automatic machines for the production of transverse wires (so called slitting machines with a cutter). Nedjtvpilopfx Ahvocn We also have a number of single point welding machines for steel wires.

Condition: excellent (used), Line for door jambs (frames), with END-CUTTING, ROUTERING for COUNTER-PLATE and HINGE INSERTION (Anuba). Composed of: Njdpfeqwyclex Ahvjcn X10030A) Loading Conveyor X10030B) Transfer Conveyor X10030C) Double-end cutting and drilling machine "AMS" - Left-side Cutting 45° - Drilling - Cutting 90° - Right-side Cutting 45° - Drilling X10030D) Angular Conveyor (90°) X10030E) Anuba Inserting Machine "MASTERWOOD" Mod. MULTITEC X10030F) Strike Plate Routering Machine "MASTERWOOD" Mod. Teknomat 3000

Condition: excellent (used), UNLOADER (SINGLE-CAGE) - Vacuum system with its pump - Top holding bar deplacement (pivoting) of 180° - Horizontal-longitudinal bars (rocker arms) for the vacuum cups supporting - In-side lifting table, surface with motorized-rollers Nedecggy Sspfx Ahvocn - Front-side sliding door (or metal grid) to out-feed the stack of the panels - Separated electric and command panel - Out-side rollers way (on ground) to out-feed pile of panels from the Unloader - Out-side motorized rollers table (which brings panels to the Unloader), with also cross motorized conveyor belts (at 90°) - Working capacity (cycles/min): 12-15 - Min/Max panels thickness mm 10 - 40 - Min dimensions of the panels mm 250 x 320 (estimated) - Max dimensions of the panels mm 1200 x 3000 - Total installed motor power KW 10

Condition: good (used), Year of construction: 2007, Technical characteristics : - Max machinable length 3200 mm - Minimum machinable length 200 mm - Maximum width 200 mm Nodpfx Ast R T Hcjhvscn - Minimum width 40 mm - Maximum workpiece height 130 mm - Depth with max Ø to tenon 320 mm: 105 mm - Tenoning carriage speed min / max 0/100 m / min - Min / max profiling speed: 3/15 m / min Tenoning: 1- end cut saw 5.5 hp (4 kW) Saw Ø 400 mm 2- tenoning router Counter bearing 50 x 620 mm 15 hp (11.3 kW) Max tool Ø 320 mm Axle stroke 575 mm Automatic splinter guard 3- tenoning router Counter bearing 50 x 620 mm 15 hp (11.3 kW) Max tool Ø 320 mm Axle stroke 575 mm Automatic splinter guard Vertical positioning with continuous axis 4- Digital angular adjustment clamp Profiling: 5-: router to be profiled on the right Shaft 50 x 320 mm 10 hp (7.5 kW) Ø tools 130/240 mm Axle stroke 280 mm Time-delayed anti-shattering intervention during calibration Double direction of rotation Vertical and horizontal positioning with continuous axis 6-: router to be profiled on the right Shaft 50 x 320 mm 10 hp (7.5 kW) Ø tool 130/240 mm Axle stroke 280 mm Vertical and horizontal positioning with continuous axis 7-: router to be profiled on the right Shaft 50 x 320 mm 10 hp (7.5 kW) Ø tool 130/240 mm Vertical and horizontal positioning with continuous axis 8-: close-out recovery group Vertical and horizontal positioning with continuous axis Device for extracting the shutter 9-: lower horizontal shaft for groove Vertical and horizontal positioning with continuous axis 88.5 hp (66.4kW) 10-: digital guide 11-: Return of parts to the operator NO TOOLS AVAILABLE OBTAIN ADDITIONAL PHOTOS NOTE: SUBJECT TO CHANGES IN TECHNICAL DATA

Condition: used, Year of construction: 2001, spindle tilting: Ja -25 bis +45° height adjustment: elektrisch tilting adjustment: elektrisch read out tilting: digital read out spindle height: digital read out fence: Siko Zähler spindle diameter: 30 mm speeds: 1.500/3.000/4.000/4.500/5.000/6.000/8.000/9.000/10.000 U / min motor power: 7,5 kW motor brake: Ja, automatisch feeder: Wegoma 4 Rollen Njdpewx Nnbjfx Ahvocn suction connection: 2 x 120mm machine length: 1900mm machine depth: 1400mm weight: 1000 kg

Condition: good (used), TECHNICAL DATA - Main beam: IPE 600 mm (various sizes & load capacities available) - Secondary beam: Sigma 410 mm (220 & 260 mm also available) - Decking: P6 chipboard, double-sided coated, 38 mm Ncsdsgpxf Hjpfx Ahvon - Load capacity: 500 - 1,000 kg / m² - Colour: RAL 9010 Pure White - Condition: used Large quantities available immediately from stock in Nordhorn. The IPE 600 allows for large spans! Scope of delivery: - Columns - Main and secondary beams - Bracing crosses - Flooring PRICES: from €40.00 net per m² Prices may vary depending on design (load capacity and column spacing). Please contact our team for a consultation. Optional accessories - Handrail - Flush wall connection - Staircase - Transfer station - Impact protection YOUR CONTACT PARTNERS: - Tanja Henkelmann - Rainer Nürenberg - Oliver Kopp TRANSPORT & INSTALLATION We are happy to assist with the transport and installation of the item. Pickup is available. Delivery or shipping can be arranged for an additional charge. Additional costs depend on the delivery location and shipment size and can be quoted individually. PAYMENT TERMS Payment terms are to be agreed upon when placing an order. The price is to be understood as a unit/net price or as stated in the description (plus VAT). Naturally, you will receive an invoice with VAT shown. ABOUT US DLK, based in Nordhorn, supplies new and used products in the areas of warehouse logistics, conveyor technology, mezzanine floors, textile storage, as well as machinery for trade, industry, and crafts. We continuously offer attractive used equipment from various manufacturers/brands at competitive terms. Please feel free to contact us with any questions. Four wins – The DLK success pillars – Warehouse Technology | Levelmaker® | Logistics | Solutions

Condition: good (used), WEBER tube extrusion line including: WEBER DS 8.5 Elmepla saw Ncedpfx Ajvryhyjhvjn Battenfeld R200/6 Battenfeld V125