Jaw Crusher Böhringer

Böhringer Splittbrecher 800x200

Year of construction: 2009, operating hours: 214 h, condition: like new (used), functionality: fully functional, Thin-Cutting Frame Saw DSG Sonic – Wintersteiger Model / Type: DSG Sonic Year of Manufacture: 2009 Condition: EXCELLENT, only 214 operating hours Technical Specifications 🔹 Cutting and Block Parameters: - Feed speed: approx. 1.7 m/min - Saw frame stroke: 210 mm - Stroke frequency: approx. 550 strokes/min - Cutting heights depending on saw length: - Saw length 380 mm: Cutting height 30–88 mm (with Air Jet and magazine), 45–88 mm (with double planer) - Saw length 420 mm: Cutting height 30–128 mm, 45–128 mm - Saw length 500 mm: Cutting height 80–210 mm, 45–210 mm - Saw length 550 mm: Cutting height 80–254 mm, 45–254 mm - Block lengths: - Basic machine: +185 mm - With magazine: 250–1700 mm - With double planer: +250 mm - Block height variation: ±0.5 mm - Cutting width with side fence: 140 mm 🔹 Additional Technical Data: - Cutting width with center fence: 2 × up to 60 mm - Optional channel width: 2–4 × 15–60 mm - Minimum lamella thickness (depending on wood type and cutting height): >1.5 mm - Kerf thickness (material loss): from 0.9 mm Blade lifespan (depending on wood): approx. 40 hours 🔩 Machine Weight: Basic unit: 3000 kg 🔉 Noise Levels (hearing protection required): At 1 m from the machine: - Idle: 97 dB(A) - Cutting: 99 dB(A) At the operator's workstation: - Idle: 85 dB(A) Hsdpfx Adsw Dp Ufsaeh - Cutting: 88 dB(A) 🌬️ Extraction and Compressed Air Requirements: Dust extraction: Two connections: Ø 120 mm and Ø 150 mm Capacity: 3200 m³/h (30 m/s) Compressed air: - Minimum pressure: 6 bar - Consumption: 200 l/min Lubrication: Centralized system with guide monitoring ⚡ Electrical Data: - Power supply: L1, L2, L3 + PE - Power cable cross-section: up to 16 mm² - Control cable: 2 × 1.5 mm²

Condition: good (used), Year of construction: 1992, functionality: unexamined, overall weight: 18,000 kg, power: 250 kW (339.91 HP), For bulky waste, pallets, residual wood, etc. Single-shaft shredder with electrohydraulic drive Rotor width: 2500 mm Hodoq I Rkdjpfx Adajh Rotor diameter: approx. 500 mm Electric motor: 250 kW

Condition: good (used), functionality: fully functional, power: 239 kW (324.95 HP), overall weight: 50,500 kg, Year of construction: 2002, operating hours: 11,245 h, machine/vehicle number: CCC00513, 239 kW weight: 50,5 t Hodpfx Aelhqhmjdaoh engine complete overhauled tracks as new new cylinder-sealing

Condition: used, Tube bending machine, mandrel bending machine, bending machine for tubes and profiles Tube bending unit with SIEMENS servo motor and planetary gearbox Year of construction: 2003 Bending capacity: max. Ø 20 x 1 mm Bending radius: max. R 70 mm Bending angle: max. 200° - last used for round tube Ø 15.4 x 0.8 mm, R60 mm - Bending tools and bending jaws interchangeable - Bending tool drive via AC servo motor and Alpha spur gear, planetary gearbox - 2-part bending tool opens and closes via hydraulic stroke movement - MERKLE hydraulic round block cylinder, item 014445 for hydraulic tool opening - Pneumatic height adjustment of the bending jaw via Festo compressed air cylinder - without electrical control - without hydraulic unit Dimensions L/W/H 760 x 400 x 150 mm weight: approx. 60 kg good condition Removed from a functional special machine, tested before removal. Drive: Brushless permanent magnet servo motor SIEMENS Typ:1FK6061-7AF71-1EG0 Nominal torque = MO: 6.4 Nm Hodpfx Aod E A I Isdaeh Rated current = Io: 6.1 A Speed = n. max.: 5500 rpm - Brushless permanent magnet servo motor SIEMENS ----- 5 pieces available in right-hand version. 5 pieces available in left-hand version. The price quoted refers to 1 bending unit with servo motor. If required, we also sell individual assemblies of the bending unit. We also offer the electrical components for controlling the servo motor. We also offer hydraulic units.

Condition: reconditioned (used), Year of construction: 2012, operating hours: 25,895 h, functionality: fully functional, pressing force: 78 t, filling opening width: 1,100 mm, filling opening length: 1,500 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 600 kg, overall weight: 24,000 kg, oil tank capacity: 1,000 l, power: 55 kW (74.78 HP), volume flow: 930 m³/h, Technical data baler: Manufacturer Presona AB Typ LP 80 VHK 1 Year of construction 2012 Total machine operating hours 25,895 hours, as of July 2025 Pump operating hours, effective 14,135 hours, as of July 2025 Number of bales pressed 235,597 pieces, as of July 2025 Press power main press 78,5 tons Specific press capacity 95 N/cm² Press power of pre-press 28 tons Volume of pressing chamber 2,7 m³ Feed channel1,500 x 1,100 mm Theoretic throughput rate 930 m³/h Throughput rate under operating conditions 410 m³/h Bale size 750 x 1,100 mm Driving motor 55 kW Tying system 5 fold vertical, 3-fold horizontal, full automatic Throughput rate with a bulk density of 30 kg/m³ approx. 9 to 12 tonnes/hour, depending on material 50 kg/m³ approx. 14 to 17 tonnes/hour, depending on material 100 kg/m³ approx. 16 to 25 tonnes/hour, depending on material Throughput capacity with MSW (Municipal Solid Waste) approx. 20 to 27 tonnes/hour, depending on material Bale weight 450 up to 600 kg, depends on material and bale length Hsdpfxovwlqqj Adaoh Volume hydraulic oil tank 1,000 l Baler dimensions built up with hopper 10,985 x 3,750 x 4,310 mm (l x w x h) Transport dimensions only baler 10,985 x 2,300 x 2,900 mm (L x w x h) Machine weight baler approx. 24 tons Condition of the press: The machine was partially overhauled and serviced in our workshop and, once the work was complete, tested in manual and automatic mode during operation. The following overhaul work was carried out: Machine cleaned, partially derusted and partially repainted Hydraulic oil tank emptied and cleaned Oil filter and air filter replaced, new hydraulic oil filled Press ram dismantled and cleaned All four rollers removed from the press ram and replaced Wire station with deflection rollers for the lower wire cleaned and made operational Side guides removed from the press ram, smoothed, mounted and readjusted Main hydraulic cylinder dismantled and disassembled for inspection Piston rod replaced, cylinder tube honed Complete seal set replaced, pressure test carried out Vertical and horizontal needle system for binding dismantled, cleaned, wire deflection rollers made functional and serviced Chain cleaned, greased, chain tension readjusted Drillomat cleaned, wire knife, drill shafts and drill fingers checked, retightened with torque and serviced Door contact switch checked and partially replaced. Emergency stop switch checked. Complete electrical wiring checked and partially replaced. Bearings of the wire guide rollers under the press replaced. New safety grilles for vertical and horizontal binding manufactured and installed. Machine checked, general maintenance work carried out and press tested in manual and automatic mode Scope of delivery: Only the baler will be sold. Comments: The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: reconditioned (used), Year of construction: 2007, - Primary impact crusher, Brand Laron Model IM 16 - Complete assembly, available as mobile or static unit. - New rotor bearings - New rotor blow bars - Front jaw (impact plate) in near-new condition - Production capacity: 800 t/h - Feed opening: 2320 x 1700 mm. Motor: 600 HP - New bearings and supports - New rotor blow bars - Apron feeder: width 2000 mm, length 10,000 mm. Gearbox and 40 HP motor. Feeder condition: semi-new - Disc pre-screen: width 2000 mm, diameter 1000 mm. Gearbox and electric motor - Hopper with 40 m³ capacity. Bolted and sectional for easy transportation Hodeimwg Hopfx Adash - The entire assembly is mounted on a chassis with tractor head coupling and can be transported on dolly axles. We also have secondary hammer mills, screens, and conveyor belts available to complete a plant.

Condition: used, Year of construction: 1985, Jaw crusher 1200 x 900 Year of manufacture (according to specification): 1985 Manufacturer: Skoda Hedpfx Adjxz Ukdjash Double toggle Feeding Drive Fully functional

Condition: ready for operation (used), Jaw Crusher Kleemann Brand: Kleemann Hedju S Tqvspfx Adaeh Type: SSTR 1250 Feed Opening: 1250 x 950 mm Incl.: E-motor Weight appr. 38 Tons

Condition: good (used), Drying oven for uv line Hsdpfx Adjt Ag Uqeajh

Condition: good (used), functionality: fully functional, Opening: 620 x 350 mm Rotor-diameter x -width: 1.060 x 610 mm Hjdpfx Aslgzrhedash feed size hardrock -180 mm feed size limestone -300 mm, complete with E-drive, conveyor and steel-construction