Edge banding machine

WINTER KANTOMAX EASY

Condition: excellent (used), Wide Belt Sander for Calibration and Fine Sanding SCM Model RCS 1st Unit: Calibration Roller, Steel 2nd Unit: Combination Unit (Roller 60 Shore, sanding pad with 2 inserts – hard, soft) Working width: 920 mm Abrasive belt dimensions: 930 x 1,525 mm Main motor power: 11.0 kW, 400 V, 50 Hz Feed motor power: 0.37 kW, 400 V, 50 Hz 2 feed speeds Electromotive table height adjustment Main switch lockable 2 x emergency stop Table extension with 2 rollers, front and rear Sanding pad inserts fitted with new graphite cloth Including as-new sanding belts All documentation included Note for used machinery: • Specifications, data, and prior sale are subject to change. Kjdpfx Adjxqggce Nowt • Prices stated are ex works – free loaded! • The machine has been cleaned and functionality tested. • All machines are sold as seen without any rights to warranty. Buyers are welcome to inspect the machines on site. • Special agreements are only valid in written form. (We only respond to inquiries that include your address and telephone number!)

Condition: used, Year of construction: 1997, - edge banding unit - Cross-cutting unit - Milling unit - Fine trimming unit - scraper - buffing unit Ksdpjd Inktefx Ad Newt

Condition: used, Holz Her Sprint 1312 FÜ + PU Heavy-duty design – edge thickness 0.4 - 12 mm PLC screen control Pre-milling unit for application before the gluing section Fully automatic edge magazine for roll and strip material Glue application station for cartridges + PU bonding automatic tracing nozzle Workpiece height 6-55 mm End trimming unit for roll and strip material up to 12 mm edge thickness with adjustment from 0-10° angle of the trimming saws Milling unit, flush milling up to 12 mm, radius milling – bevel milling - 15° motorised - 4 axes Scraper unit for bevels and radii with 2 pneumatically operated scraper holders pneumatic infeed and outfeed Flat scraper unit – finishing Spray device – PU Machine in TOP CONDITION Available from stock Lieboch Kwodpfox Eilqox Ad Nst

Condition: as good as new (ex-display), Year of construction: 2026, Compact wide belt sander with combined sanding unit Action equipment: - Switching the sanding shoe on and off from the control panel Kjdpfx Adjgf Sw Ne Newt - Switching the roller on and off from the control panel - Electronic control Fox 500 KTR - Table extension with 2 rollers with infeed and outfeed - Automatic table positioning with push button Item number: 5222100A2 Also for smaller craft workshops for occasional use Combination sanding unit with sanding shoe for fine sanding As standard with angular grooved steel roller Ø 120 mm for calibrating Fine adjustment of the working height Clearly arranged control panel on the front side Robust tube-stiffened monoblock steel machine body, robot-welded, working units mounted high up for maximum rigidity Motorized height adjustment of the work table with digital display Electronically controlled sanding belt oscillation Carpet feed via gear motor with two speeds Natural rubber feed carpet with negative profile Flexible steel pressure rail in front of the first unit Rubber pressure rollers, in front of or behind each working unit Pneumatic belt tensioning for each unit with decimal correction option for grain size / belt thickness Universal use for solid wood and veneer thanks to combination unit Entry model for smaller companies Working width 950 mm Equipment details Combination unit for calibrating and grinding Angled steel roller Ø 120 mm with fine height adjustment Hard grinding shoe with graphite support Universal design for calibrating

Condition: used, Year of construction: 2018, Used machine Year of manufacture: 2018 Special feature: Machine for up to 100 mm edge height! Condition: Factory-inspected by Lange Maschinenbau Equipment and technical data: - Machine table with 13 running rollers for improved workpiece guidance - Edge feeding, synchronous with belt feed - Edge thickness adjustable via digital counter - Pneumatic roller separation with knife (for cuttable edges) - Three pressure rollers - Belt feed: - 0.25 kW - approx. 1250 mm long - approx. 6.0 m/min - 50 mm wide toothed belt with thick, workpiece-friendly rubber top - Digital counter for height adjustment - Direct glue application to the workpiece: drip-proof glue pot with glue supply from below and rapid heat-up time after standstill - Flush cutting unit: - for front and rear workpiece edges - automatic sensing at the workpiece - pneumatic cutting with knife for cuttable edges Kjdpfx Ajwka S Isd Njwt - Flush trimming unit - with vertical sensing and horizontal guidance - reproducible setting using digital counters - 2 powerful 0.4 kW high-frequency motors - stepless speed adjustment from 4000 to 18000 rpm - Cutter Ø 70 mm, Z4, radius 2 mm/15° - central extraction nozzle Ø 100 mm - 2 chip extraction hoods with hose Ø 60 mm - Automatic height adjustment of the upper cutter with belt feed - Continuous workpiece support approx. 1800 mm long - Workpiece support rail, extendable by approx. 300 mm - Rotatable foil dispenser Ø: 800 mm - Workpiece width: min. approx. 80 mm - Workpiece thickness: 10 – 100 mm - Workpiece length: min. approx. 220 mm - Edge thickness: 0.4 – 2.0 mm - Roller separation: max. 1.0 x 55 mm, 2 x 45 mm - Glue pot heating capacity: 2.7 kW - Heat-up time: approx. 10 minutes - Working height: approx. 880 mm - Electrical connection: 400V, 50 Hz, 3Ph + N - Total connected load: 3.8 kW - Pneumatic connection: 6 Bar Dimensions (without foil dispenser): approx. 1800 x 700 x 1300 mm Weight: approx. 260 kg Availability: short-term Location: Flörsheim

Condition: used, Year of construction: 2001, Baffle width: 4000 mm. Baffle height: 1000 mm. External dimensions: 4600 x 1500 mm. 2 x 1.5 kW motors. Total nominal flow rate: 7000 m³/h. Right and left exhaust nozzles with 300 mm diameter. Kwedpfovvizkex Ad Njt Storage location: Garbsen

Condition: good (used), functionality: fully functional, Tested, functional equipment, used edge bander BIESSE Polymac model LATO 38 - Glue pot - Guillotine - Front/back trim Kwedpouhm Adsfx Ad Not - 1 tiltable top/bottom flush trimming - 2 tiltable top/bottom flush trimmings - Exit brushes Possibility to test at our facilities Machine visible in our Cosne workshop Price includes loading onto truck

Condition: used, Year of construction: 2011, Pneumatic milling adjustment (Straight/Radius) Combination milling station R=2 Corner rounding cutter R=2 to 40 mm Jointing cutter up to 40 mm Flat scraper Profile scraper R=2 Short workpieces PLC control with Pro Face touchscreen Nesting Cooling/antistatic spray - airtronic Protective spraying Kante Riepe incl. interchangeable tank Workpiece thickness 8 - 60 mm Mechanical edge clamping Extraction nozzle: 140 mm Dimensions: Length with extension: 4984 mm Depth with roller table: 1425 mm Max. height: 1618 mm Worktable height: 888 mm Weight: 1400 kg Storage location: Nattheim Kwedexyiilepfx Ad Net

Condition: used, Year of construction: 1996, Edge thickness: 0.4 - 12 mm Roll edge: 3 x 45 mm or 0.8 - 60 mm Minimum workpiece width: 65 mm Minimum workpiece length: 160 mm Workpiece thickness: 10 - 55 mm Feed rate: 13 m/min Pre-milling (joining) Glue pot Quickmelt Gluing unit Trimming Flush trimming Chamfering Radius trimming Corner rounding Flat scraper Buffing unit Machine dimensions: 7450 x 1220 x 2400 mm Weight: 3000 kg Kwedpsvvkd Tefx Ad Njt Storage location: Nattheim

Condition: used, Holz Her Sprint 1317-1 FÜ + PU heavy-duty design – edge thickness 0.4 – 5 mm SPS screen control Kwedpfx Ajx It Hmed Njt large LCD display pre-milling unit before gluing area fully automatic edge magazine for coil and strip material glue application station for cartridges + PU gluing maximum edge height 51 mm automatic glue height adjustment press unit 1913, motorized pneumatic trimming unit for coils and strips with pneumatic adjustment for miter saw angle from 0–10° multifunctional milling unit 1942 MOT 2 milling unit with motorized adjustment axes for various radii – chamfering – flush milling via SPS copy milling unit 1832 for corner copying up to R 3 mm + postforming up to R 6 mm scraping unit for chamfers and radii pneumatic infeed and outfeed finish – surface scraper regular maintenance by Holz Her machine is FACTORY SERVICED, in EXCELLENT CONDITION available from stock in Lieboch