Single shaft shredder

WEIMA Spider WLK 1500

Condition: used, Technical details: drive motor: 4 kW revolution per minute: 14 U/min voltage: 380 V / Hz weight: ca. 0,5 t Njdpeu Nxrpsfx Adkodd Chip Crusher - Shredder 2-shaft crusher current feed size 400 x 360mm crushing tools 8 pieces per shaft current drop-out size L: 350 x W: 250mm gear motor manufacturer Vector accessories: 2 crusher discs *

Year of construction: 1994, condition: ready for operation (used), Motor power: 15.5kW/19.5kW, pressing force: 320kN, spec. pressure: 425kN/m², machine dimensions X/Y/Z: approx. 5700mm/1900mm/1800mm, weight: approx. 6000kg. The machine has a defect due to moisture and should be checked. Njdpfjip D Rpsx Adksdd

Condition: good (used), Year of construction: 2011, operating hours: 20,580 h, functionality: fully functional, pressing force: 48 t, filling opening width: 1,020 mm, filling opening length: 1,250 mm, bale length: 1,200 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 450 kg, input current: 59 A, overall weight: 12,000 kg, transport height: 2,750 mm, oil tank capacity: 300 l, power: 30 kW (40.79 HP), transport width: 2,300 mm, transport length: 8,500 mm, tank capacity: 300 l, Good day, We hereby offer you a used baler from the manufacturer HSM, type VK 4812. The following technical data was taken from the manufacturer's operating instructions and brochures, for which we cannot accept any liability for correctness and completeness. Manufacturer HSM Type VK 4812 Year of manufacture 2011 Operating hours 20,580 hours Main press force 48 tonnes Drive power 30 kW Machine weight press 12 tonnes The machine documentation is available in German. A viewing is possible by appointment in our workshop. Njdpfx Adjt H Rcaokodd We would be delighted if this machine is of interest to you. Your service team Mertens & Frowein GmbH

Condition: excellent (used), Year of construction: 2014, operating hours: 753 h, functionality: fully functional, machine/vehicle number: 60501401, type of input current: three-phase, total width: 2,000 mm, total length: 4,100 mm, total height: 2,800 mm, protection type (IP code): IP54, power: 30 kW (40.79 HP), Mechanical vapour recompression vacuum evaporator with forced circulation for water treatment. Nodpfx Astuklhjdkodd Nominal production of distillate: 15000 l/24h Comissioned in 2014 and hardly used, fully functional.

Condition: new, Year of construction: 2025, Manual pan & box brake SM 1270x2 mm is a machine for bending different elements from the metal sheets with maximum length 1270 mm and maximum metal thickness 2mm. Usually folding machines are used for producing roofing elements, ventilation elements, drainage system elements etc. But manual pan & box brake SM 1270 thanks to special segmented bars can bend boxes and façade cassettes in addition to standard bending elements. Segmented bar is a bar consisted of parts with different lengths. So you can adjust it to the length you need to bend boxes and cassettes from all four sides. There are models of manual pan & box brakes we produce: Manual pan & box brake SM-1270 x 2mm Manual pan & box brake SM-1550 x 1.8mm Manual pan & box brake SM -2020 x 1.2mm Those manual box & pan brake in standard set have two bars segmented: The upper bar and rotation bar. The upper bar has a 135 degrees’ angle, so it’s possible to bend elements with maximum bending angle up to 135 degrees. The standard set of manual pan & box brake SM includes: - Manual box & pan folder - Angle measuring device - Four position angle limiter - Two segments with side cuts to bend cassettes with inside bends. Ndedpfxjf Eywwe Adkod As an additional option you can get: -Third segmented bar -Segments tempering option (in standard set pan & box brake’s segments go not tempered, but if you work with metal thickness more than 1mm we advise to temper one- so rigidity of segments will be higher and usage time of machine longer); - Change of upper segments height (from 30 to 45mm). So it lets to bend cassettes with height up to 45mm instead of 30mm. - Cross cutting knife. Designed for cutting metal sheets before bending them with folding machine. The maximum metal thickness for cutting is 0.8mm; - Multifunctional acceptance table to adjust different length limiters in different parts of bending machine. So it lets to save your time while same sizes cassettes or elements production. Dimension: 160.00Sm x 82.00Sm x 120.00Sm Weight: 350.00Kg

Condition: used, machine/vehicle number: 12599, Rotor diameter: 600 mm Ndodpfx Adek N Iy Noksd Rotor width: 1450 mm 12-knife rotor 3 rows stator knives Inlet cross section approx. 780 x 1490 mm Drive motor: 132 kW

Condition: used, Year of construction: 2010, operating hours: 9,100 h, Hello, I have for sale a Doppstadt AK 630 high-speed hammer shredder/chipper with a sieve from 2010. Mileage is 9,100 mth. The machine is in very good condition. I invite you to purchase. Nodpfx Ajv Unq Ujdkedd

Year of construction: 1976, condition: excellent (used), Full frame saw / frame saw BÖGLI KHV-700 Marathon Year of manufacture: 1976 75HP, 380V, 50Hz max. passage 710 mm Ndodpfx Adjpyglisksd stroke: 500 mm with splitting wedge Marathon 2 very good condition - available immediately Location: Austria, near Feldkirch

Year of construction: 2024, condition: new, ♻ Universal use (various wood, pallets with nails, chipboard Ndodpon Nwxfofx Adked boards, waste and scrap, veneer, MDF boards, cardboard boxes, plastics, textiles, tires, etc.). ✔ Power: 55/75/90/110 kW ✔ Shaft length: 1400 mm ✔ Shaft diameter: 315 mm ✔ Shaft RPM: adjustable ✔ Number of cutting knives: 60 ✔ Granulation: 15-90 mm ✔ Capacity: up to 17 m3/h* ✔ Filling opening: 1400 x 1800 mm ✔ Dimensions L/W/H: 2,20/3,10/2,80 m ✔ Weight: 7000 kg 2 years warranty or 2000 working hours

Condition: used, machine/vehicle number: 11481, Rotor diameter: 300 mm Rotor width: 600 mm Ndsdpfoghgmzsx Adkjd 3-blade rotor 4 rows of stator blades Inlet cross-section approx. 250 x 600 mm Drive motor 37 kW