Twin screw extruder

Weber DS 120

Condition: new, *TECHNICAL SPECIFICATION: Heating capacity: up to 36 kW per consumer circuit Iaodjg Ezarjpfx Aa Ejw Cooling capacity: up to 30 kW per consumer circuit at -30°C Load circuits: 1 or 2 as standard Temperature range: - 45°C to +130°C Medium: water / glycol mixture Dimensions LxWxH (without connections) : 1-circuit: 1950 x 1280 x 1725 mm 2-circuit: 2150 x 1640 x 1725 mm Weight: 1-circuit: approx. 1300kg 2-circuit: approx. 1500kg *HIGHLIGHTS EQUIPMENT: -Controls: Temperature control (standard) -Control via SPS with touch screen -Analogue and digital interfaces -Internal 2-circuit pump system (INFO: Ensures performance values even at low flow rates) -Heating control via solid-state relay (SSR) -Flow measurement in the internal circuit for flow monitoring (INFO: If the water/glycol mixture is incorrect, the system automatically warns and switches off in the next step) -Pressure-controlled cooling water regulator (INFO: Much more accurate than temperature controls) Stainless steel tank, corrosion-resistant components (stainless steel/non-ferrous metal) (non-ferrous metal-free optional) All medium-carrying components and piping insulated for low-temperature application -Water-cooled condenser (air-cooled on request). *OPTIONS: -flow rate control: up to 100l/min, >4 l/min +/- 5% of measured value -Pressure control: 0.5 to 4.5 bar (control range) -compressed air monitoring -test piece emptying by means of compressed air - Cooling water monitoring -Limitation of inlet pressure -Other special options available on request and after technical inspection Visit our website for more details or for other performance classes. *This unit conforms to the European Directives. Other directives and standards are only fulfilled if they are listed in the order confirmation. This technical specification reflects the standard equipment, customer requests deviating from the standard will be shown in quotations or order confirmations.

Condition: used, Year of construction: 2006, Kahl Twin Screw Extruder is a machine manufactured by Kahl in 2006. Currently stored in Germany, it comes equipped with a fine grain hopper, fine grain discharge, fine grain sack, a belt unit (Type: BTK 1510-0), water addition, extruder, supply air blower, reconditioned in 2016. It also includes dust removal, tumbler sieve, dedusting, final packaging, belt dryer, product hopper, pipe chain conveyor, cyclone, rotary valve, distributor, dust sack, exhaust air blower, air stream rotation dryer, feed table, mixer, and an additional air supply blower and belt dryer. The delivery terms are FCA. Iaedpjvfxqyjfx Aa Eow Equipment: 1 x feed table, 1 x tube chain conveyor, 1 x mixer 1 x water addition, 1 x extruder, 1 x supply air fan, 1 x cyclone, 1 x rotary valve, 1 x distributor, 1 x belt dryer, 1 x product hopper, 1 x tube chain conveyor, 1 x fine grain hopper, 1 x fine grain discharge, 1 x fine grain bag, 1 x supply air fan, 1 x belt dryer, 1 x rotary valve, 1 x dust bag, 1 x exhaust fan, 1 x airflow rotary dryer, 1 x dedusting, 1 x tumbling screen, 1 x bar removal, 1 x final packaging 1 x belt unit, type: BTK 1510-0 refurbished 2016

Condition: excellent (used), Year of construction: 2004, T-Die Serial No.: L 1081-041391 // Calender Serial No.: F 1201-041392 Haul-Off Serial No.: F 1201-041392-T Max. winder speed: 50 m/min Type: Film system 1080 mm usable width Equipment / Additional information: Max. gross output PP up to 1000kg/h with film width up to 1200mm A special feature is the winding system, which can cut narrow films (150 mm - 100 mm) or for example 8 x 175 mm or even 2 x 700 mm one nozzle lip with a max. film thickness of 2mm up to 1000kg/h. Total power consumption: 211 kW/h Main engine power: 250 kW Min. 068 mm film thickness in PS / min. 0.75 mm in PP Maximum calender speed: Max. 50 m/min. mechanically possible Consists of: -Dosing system 5-chamber Maguire -Extruder (160 mm screw) Amut EA 160 // Age: 2003 -Screen changer (for cleaning in food production) -Melt pump -Slot die (1 insert) 120 cm -Lip with max. film thickness up to 2mm up to 1000kg/h -Calender 140 cm -Thickness gauge SBI TMD-EC/140.20.200.R Iedpfew Tbr Hsx Aa Eoaw -Post-cooling rollers (4 pcs.) -Winder (Film jam during roll jam) -Cutting machine & film tensioner -Film winders (3 pcs.) -Mill MAZZA CBS 25 40 2T18 // Age 2003 Fully existing infrastructure; control cabinets, pumps, etc.

Year of construction: 2002, condition: excellent (used), functionality: fully functional, Twin-screw extruder Ref. No.: DE27695 Manufacturer: Leistritz Type: ZSE 40 HP Year of manufacture: 2002 Ijdpfx Aaox Dip Te Eeaw Screw diameter: 2 x Ø 40.0 mm L/D: 40D Drive: 70 kW Details: co-rotating, segmented screws and barrel, 1 x segment for side feeding Options: pelletizing, dosing, side feeder Does this offer not meet your requirements? Please visit our website Plama Engineering or send us your detailed inquiry, we have suitable solutions for almost every budget.

Year of construction: 2021, condition: new, Overband plate magnet from remaining stock / overproduction Manufactured from stainless steel 1.4301, hermetically sealed. For sale: a plate magnet with threaded holes on the back. Iasdpofktk Hefx Aa Esw The magnet can be used as a "police magnet" or to filter out metal contaminants above a conveyor belt. Ring eyelets for suspension are included. Dimensions of the magnet block: 620 x 420 x 250 mm Only 1 unit available for immediate delivery. Many other dimensions available in stock.

Condition: excellent (used), total length: 3,000 mm, total width: 1,500 mm, Panel press in very good working condition + Grecon finger jointing Iasdpfxet Uduxe Aa Eew

Condition: refurbished (used), functionality: fully functional, Refurbished, six-piston hydraulic flatbed press of Italian manufacture. Branded veneer press for easy wood veneering, with warranty and service. Veneer sheet dimensions: 3000 x 1300 mm Pressure at full surface: 2.5 kg/cm2 Total maximum pressure: 90 tons Number of hydraulic pistons: 6 MYLAR Teflon film on the plates Prepared for water-based plate heating Option to install a hot water boiler Price includes complete machine refurbishment Ijdpovvbbcjfx Aa Eeaw Price: 12,000 EUR (excluding VAT) The machine is refurbished, adjusted, and tested. The condition of the refurbishment and the machine's readiness for delivery must be verified in advance! In stock: Telnice near Brno, Czech Republic Testing, demonstration of the machine, and operator training are standard.

Condition: excellent (used), Year of construction: 2011, operating hours: 28,000 h, functionality: fully functional, clamping force: 1,300 kN, For sale is a hybrid injection molding machine, 2 components, of the brand KraussMaffei and type KM 130-750 CX The machine is in very good condition, ready for immediate use, with low operating hours. Electronic injection unit and dosing unit, hydraulic clamping unit. Technical data: Year of construction: 2011 Operating hours: 28,000 h Clamping force: 130 T Cylinder Ø 30mm / 40 mm (& 2*50mm additional) Core pull: 1*Hydraulic Valve gate: Pneumatic Tie bar extension: 160 mm Internal pressure transducer Selector switch On request, transportation and loading can be organized at an extra charge. can be organized throughout Europe. Prices plus VAT Viewing possible by appointment. Contact us, our team will be happy to help you. Trade-in or exchange possible! Machines purchase / sale PURCHASE / SALE OF PRODUCTION & METALWORKING MACHINES AND MUCH MORE. Do you need a high-quality but inexpensive metalworking machine for your production? Or do you want to sell yours? Iaedpfxsu Hxm Us Aa Esw For further information or contact options, please visit our website

Year of construction: 1998, condition: used, Technical details: profile width: 50 mm work height max.: 950 mm interface: RS 232 Pinout Window profile processing machine for materials such as plastic, aluminum and wooden windows in a continuous process. The materials are conveyed by a pneumatic transport and clamping system. The system consists of two work stations (machines), an electrical control cabinet, and a control panel and transport units. As well as columns with transport system vibrator, chip transport unit and column with receipt printer. Our photos are first taken from the location and then further pictures are how the plant is stored in our stock ready for transport. Workstation no. 1 (machine 1): -sawing station with saw blade Ø 400 x 4,5mm -drilling unit with clamping cartridge (vertical upwards) -drilling unit with clamping cartridge (hotizontal) -Boring with clamping cartridge (vertical down) -twin drilling unit with clamping cartridge (vertical down) -45° drilling unit with clamping cartridge (upwards) Working station no. 2 (machine 2): -drilling unit with clamping cartridge (vertical upwards) -milling spindle horizontal with 11 side milling cutters -Drilling unit with clamping cartridge (vertical down) -Drilling unit with clamping cartridge (vertical upwards) -Drilling unit with clamping cartridge horizontal 2 transport units: motor driven -LxWxH: 5.650 x 2.400 x 1.000mm -track width 1.980mm 2 pieces transport units: motor driven -LxWxH: 2.150 x 2.750 x 1.050mm -track width 2.300mm Iaedpfx Aaeu Ibuwe Eow *

Condition: new, Year of construction: 2026, Precision lead and feed screw lathe Manufacturer: OPTIMUM Iasdpfxogqw U Rj Aa Esw Model: OPTiturn TZ 4 Item No.: 3432240 Condition: New machine Center height: 200 mm Distance between centers: 800 mm Spindle speed: 45 - 1,800 rpm (16 steps) Standard equipment: - 3-axis digital display DPA 32 - Fixed center, MK 3 - Quick-change tool post, size B - Turning tool holder BD - Reducing sleeve MK 6 / MK 3 - Steady rest, fixed, ø 10 - 130 mm - Traveling steady rest, ø 10 - 100 mm - Coolant system - Chip tray, pull-out - LED machine lamp - Operating tools