Hand pallet truck

Sonderbau Transportwagen

Condition: used, Number of sanding units 4 St. sanding width 190 mm Sanding height max. 180 mm Control ja weight 3300 kg Dimensions (L/W/H) 2600x920x1890 mm Dust suction hood 2x180, 2x120 mm Löwer DSM 2004 Double-Sided Sanding Machine ----- 4-Belt Sander + Disc Unit (Top/Bottom) Manufacturer's Description: ----- Double-sided, four-belt, single-wood sander for sanding solid wood such as window frames, etc. Highly stable, top-quality design with innovative details. Suitable for high continuous loads, even with high material removal rates. - Sequentially arranged grinding units for roughing, fine grinding, and finishing, each from above and below 1. Belt grinding unit with heavy steel roller 2. Belt grinding unit with rubberized roller and shoe 3. Finishing unit with fiber brush (see optional equipment below) - Direct-drive grinding rollers for slip-free power transmission - Maintenance-free and wear-free CERMET-coated grinding shoes with very good thermal conductivity and absolute dimensional accuracy - External cooling of the grinding zones for cooler grinding and longer belt life - Forced pneumatically controlled grinding belt oscillation - Effective grinding dust extraction directly at the grinding rollers - Airborne dust extraction at the tension rollers - Integrated brushing and finishing unit with large grinding dust extraction - Motorized grinding thickness adjustment via precision threaded spindles and large linear ball bearing sets on hardened and ground precision shafts with dust and Dirt protection - Chip removal adjustment at the bottom via precision threaded spindle with dimension display via scale ring (0.1 mm resolution) - Sanding belt tension via pneumatic cylinder with constant tension pressure - Sanding belt change with pneumatic belt release in seconds - Sanding belt tracking adjustment during belt change Hjdpfx Agovu Hgbo Uen - Electropneumatic compressed air monitoring - Infeed protection via contact roller for workpieces that are too thick - Workpiece transport via calibrated, non-slip and adhesive conveyor belts over heavy-duty cast iron tables with a finely planed surface and spring-loaded pressure rollers with fine adjustment - Cardan shaft drive for smooth and consistent workpiece transport - Geared feed motor with infinitely variable speed 4-20 m/min - All motors electrically protected - Ergonomically arranged operating elements - Digital thickness display (0.1 mm resolution) with modern magnetic tape system Technical data: ----- - Sanding belt speed 22 m/s - Sanding belt length 1800 mm - Sanding belt width 200 mm - Working width 190 mm - Sanding thickness 2-180 mm - Four brake motors for drive 5.5 kW - Feed motor 1.5 kW - Feed speed 4-20 m/min - Automatic height adjustment 0.37 kW - Two brush units with fiber brushes D 120 x 200 mm at 0.37 kW each - Extraction ports 2 x 180 mm, 2 x 120 mm - Extraction air velocity 20 m/s - Pneumatic connection 6 bar - Working height 870 mm - Length (with soft disc 2740 mm) 2600 mm - Length with control unit (with soft disc 3035 mm) 2985 mm - Width 880 mm - Height 1910 mm - Weight approx. 3300 kg - Operating voltage 400 volts, 50 Hz, 3P - CE compliant Equipped with the following special options: -----...

Condition: used, Year of construction: 2005, functionality: fully functional, length stop: 3,200 mm, tool diameter: 400 mm, spindle diameter: 50 mm, spindle stroke: 640 mm, spindle speed (max.): 3,000 rpm, milling spindle length: 320 mm, saw blade diameter: 400 mm, height adjustment type: electric, type of input current: AC, working height: 130 mm, working width: 200 mm, SCM Windor 60/100 – Angle Processing Center Manufacturer: SCM Group Year of manufacture: 2005* 1. General Description of the System The system in question is a window and door production line of the type Windor 60/100 from the manufacturer SCM Group, built in 2005. It is a CNC-controlled angle processing center designed for the industrial machining of frame and sash components. The system is configured for series production and enables precise, repeatable machining in integrated process steps. 2. Main Components of the System 2.1 SCM Windor 60/100 Angle Processing Center The SCM Windor 60/100 features a modular design and is configured as an angle processing unit. Machining takes place on a tenoning side and a profiling side positioned at right angles to each other. The system combines several machining steps – such as milling, drilling, grooving, rebating, and tenoning – in a fully integrated, CNC-controlled process. Key Features: * CNC multi-sided machining * Multiple milling and processing spindles * Automated tool handling and changeover * High dimensional accuracy and repeatability 2.2 Fleximat Drilling Center The Fleximat drilling center is integrated into the system and is used for the precise execution of boreholes for joints and fittings. Machining is CNC-controlled with both vertical and horizontal drilling units. 2.3 Profiler Center The profiler center is designed for contour-forming milling operations and consists of two processing sides: Right side: * Lifting spindle with height adjustment * Suitable for variable profile and contour processing Left side: * 24-position tool changer * Automatic tool changing to minimize setup times * Suitable for complex profile milling 2.4 Löwer Surface Sanding Machine A surface sanding machine from Löwer is integrated into the production line. The machine is used exclusively for surface sanding, serving to improve the surface quality of the processed workpieces. 3. Control, Operation, and Safety The system is equipped with a CNC control unit that manages all machining operations, tool changes, as well as feed and spindle movements. Operation is semi- or fully-automated by trained personnel. The safety features are state-of-the-art as of the time of construction (2005) and include, in particular: * Mechanical guards and enclosures * Emergency stop devices * Safety locks on moving machine parts Hsdox Nqqxepfx Ag Uen 4. Optional Expansion: SCM Topset XL Planer (10-spindle) For expansion of the existing machinery, provision has been made for a SCM Topset XL planer with 10 spindles. This machine will be operated as a standalone processing station at a separate location within the production hall and is not directly integrated into the CNC control of the Windor system. The system is available and can be dismantled at any time. Dismantling and transportation are to be organized by the buyer. Available from 07.01.2026

Condition: used, Number of sanding units 4 St sanding width 190 mm Sanding height max. 4-180 mm weight 4200 kg Hess Expert 4-belt single wood sanding machine machine will be checked by our technicians ----- Ø Grinding at the bottom/top Ø With 2 offset grinding units each (bottom and top) Ø Grinding units (bottom and top) connected in series according to the Dressing principle Ø Pre-sanding with coarse grit (calibrate) Ø Regrinding with fine grit (finish) Ø Central motorized height adjustment of the lower grinding units Ø Central motorized and synchronous height adjustment of the entire upper Grinding and brushing units including the upper transport units Ø Oscillating sanding belt utilization (during the sanding process) Ø Absolute power connection thanks to 5.5 KW motors and large dimensions drive drums Ø Oxide ceramic grinding shoe for - exact surface geometry - no adjustment work - permanent dimensional accuracy - completely maintenance and wear-free Basic structure: Stable, heavy welded construction made of strong-walled rectangular profiles additional, statically calculated reinforcements for optimal Vibration dampening. Staggered grinding units with large dimensions Belt drive drums for slip-free belt running. Two-point suction for direct and flying dust with sealing brushes and integrated sanding belt blow-off Device to increase the service life of the sanding belts. Grinding units in heavy steel plate construction as the basis for vibration-damped, quiet tape running. Absolutely backlash-free guides as ball linear sets hardened and ground shafts. Height adjustment of the grinding units via hardened and ground special linear guides as well as pre-tensioned ones Guide carriage. Permanent precision thanks to dust and dirt protection Ball linear sets and guide carriages. Large-sized pre-grinding rollers as contact rollers. Contact rollers and Sanding shoes in a balanced ratio to the sanding belt grain load. The large drive drums guarantee full transmission the 5.5 kW drive power of the grinding motors on the sanding belt. Therefore Slip-free, stable running and optimal heat dissipation. This makes it the strongest Chip removal possible. Automatic machine stop activation in the event of a belt break. Visual display on the control panel and via flashing lights on the machine. Sanding shoes for finish completely maintenance-free and wear-free made of oxide ceramic with optimal heat dissipation. Grinding belt tension via appropriately sized compression springs. Sanding belt relaxation for belt changing using a pneumatic device sensitive, distortion-free placement of new tapes. Upper grinding unit and brush device centrally motorized Height adjustable with digital display in the control panel for the motorized Grinding thickness adjustment. Brushing and finishing device, for better surface finish, integrated into the basic machine. Two special brush rollers 150 mm Æ arranged one above the other in synchronous function for advance thrust. Separate height adjustment of the brush rollers on precise Carriage guides for post-correction of wear. Additional transport roller for Removal or further transport of the workpiece from the automatic grinding machine with the conveyor belt. Wooden guide in the inlet area for hard guide and bearings mounted on both sides Hsdpfx Agjt Tqy Eo Usn pressure rollers. Safe transport of profiled workpieces on ca...

Condition: used, working length 3600 mm Working width 1500 mm Working height ca. 900 mm WEINIG Return Conveyor System RF15 ----- Can be used after moulders, planers, and milling machines with a maximum feed speed of approx. 22 m/min. Technical Description: Workpiece length: 250 - 3,600 mm Workpiece width: 30-230 mm Longitudinal-transverse conveyor with two integrated, driven roller conveyors: Hodpfexpn Tnjx Ag Uen Transverse conveyor path 1,500 mm Constant conveyor speed: 30 m/min Roller conveyor length 2,200 mm Return roller conveyor (non-driven) to the operator (Technical specifications according to the manufacturer - without guarantee!)

Condition: good (used), Year of construction: 2011, Load moving system CBM 240 / ST 120 MACH-ID 923 Type: CBM 240 / ST 120 Year: 2011 Hjdpfx Agjwvhrts Ujn

Condition: new, Number of sanding units 8 st. sanding width 180 (260) mm Sanding height max. 160 mm Dimensions (L/W/H) 3065x1600x1900 mm weight of the machine ca. 1500 kg LÖWER Leistomat SD ----- Automatic fine grinding machine for wood grinding (smoothing, defibering and Edge breaking) or intermediate sanding of profiled window bars. With soft disc Technology for the visible surfaces as well as automatically safe profile and Width adjustment. - 2 lamella roller units on the side, each 0.75kW, L=120mm, D=200mm 1 softisc unit Ø=200mm above 0.75kW, 1 slat roller unit L=200mm top 0.75kW, 1 soft disc unit Ø=200mm bottom 0.75kW, 1 slat roller unit L=200mm bottom 0.75kW, 2 lamella roller units on the side, each 0.75kW, L=120mm, D=200mm - Linear guidance of all grinding units Linear ball bearing sets on hardened shafts - time-controlled immersion of all lamella roller units directly above the incoming workpiece edges. By the It is possible to immerse the aggregates deeper into the profiles to be able to deliver. - Motorized workpiece thickness adjustment of the machine - variable grinding flap speed via frequency converter for adjusting the grinding intensity using frequency converters (separate for discs, surface rollers and side rollers) - Disc aggregates as soft discs with Velcro fastener for Grinding wheels (wood pulp) - Feed via three lower and one upper conveyor belts and Spring-loaded pressure rollers with infinitely variable speed 4-15m/min - Parameters that can be set using the touch panel are workpiece thickness, Workpiece width (left side units individually), immersion depth Hodpfx Aovnv Uheg Ujn Side units, spindle speed, feed speed - Saving the parameters as machine programs in program mode - Working in automatic mode with non-contact Workpiece width detection and profile detection as well as automatic Adjustment of the sanding units to the workpiece width and the Profile shape (workpiece height is set in advance) - pneumatically clocked driven feed roller, automatic Clamping of the workpiece and feeding in after unit adjustment - Red/green indicator lights to indicate operational readiness - shortest workpiece length 380mm - Transport belt width 200mm - max. workpiece width 180mm (260mm in the envelope process) - Workpiece height 12-160mm - Suction connection 4 x 100mm and 2x80mm diameter - Sensor-controlled tool blow-off directly on the discs - Length (case) x width x height (mm): 3065x 1600 x 1900 Complete length: 4365mm (including roller conveyor with integrated workpiece width detection) - Weight: 1500kg - Operating voltage 400V, 50Hz, 3P, air connection 6 bar - CE version ----- Price of the above machine on request! ----- Special accessories with additional costs: Set of replacement slats for Leistomat SD-200 consisting of Area aggregates: 30 strips EH45 / 200 - 7 (rolls) 30 strips EH45 / 200 - 20 (rolls) Folding units: 96 strips M55 / 120 - 4 SmartFlex slat disc Ø200 solid with 30 grooves 50mm long Set of replacement slats for SmartFlex slat disc consisting of 60 strip M35 / 50 K 180-7 p Sandpaper disc VB for soft disc D=200mm grit 220 with velor backing (Velcro), pack of 100. Sandpaper disc VB for soft disc D=200mm grit 280 with velor backing (Velcro), pack of 100. ----- Price of the above-mentioned special accessories on request! -----...

Condition: used, machine/vehicle number: 008595, X axis working area: 4687 mm Y axis working area: 260 mm Working Table: Pod and Rail Hedpfjy Stvvox Ag Uon Main Electrospindle power: 19 KW Number of controlled axes: 4 axes Total number of tool changer positions: 44

Condition: new, Year of construction: 2025, functionality: fully functional, GMF Caliper Complete Set 2,500 mm, 3,000 mm, or 4,000 mm 1.) Base length: 1,500 mm or 2,000 mm 2.) Plus extension: 1,000 mm, 1,500 mm, or 2,000 mm Includes charger and receiver. The robust aluminum measuring rail is ideal for measuring glazing beads. Functionality: For use on doors and large window sashes, the GMF caliper can be safely and quickly extended mechanically up to a measuring length of 4,000 mm. - Automatic detection of extension Accuracy: ± 0.1 mm Resolution: 0.02 mm Measurement transmission via wireless interface to control unit or PC Hodpfxsxu Hyqe Ag Uen Microcontroller charger for battery pack, 100-240 V input voltage, and power adapter for Euro/UK/US/AUS NOTE: 1.) HECHT receiver software required on the customer's PC – available separately upon request. 2.) Can be retrofitted to HECHT Exenso Comfort length stops from year of manufacture 2016 onwards – available separately upon request. 3.) Can be retrofitted to HECHT DS350 double miter saws from year of manufacture 2018 onwards – available separately upon request.

Year of construction: 2014, condition: used, Number of sanding units 6 St. sanding width 180 mm Sanding height max. 150 mm STAEHLE Grinding Machine Type Gloria/Saturn E 180 RF ----- Stähle Hess Finish Grinding Machine Type Saturn E 180 RF (formerly Gloria) with 2 grinding units, plus top and bottom Roto Finish grinding attachments. 1 upper grinding belt 1 lower grinding belt 2 upper Roto Finish grinding attachments 2 lower Roto Finish grinding attachments For a detailed description, please see the accompanying PDF from the manufacturer. Hedpfxjx Dng Ds Ag Uen Sold on behalf of a customer. The images are from our archive and were taken before the machine was delivered to the customer. (Technical specifications according to the manufacturer - without guarantee!)

Condition: new, functionality: fully functional, machine/vehicle number: ST2100-001, overall weight: 450 kg, Year of construction: 2021, STEMA GLF Dowel Shooter Automatic Certainly the most productive dowel inserting machine for heavy and long dowels. Hsdpoxhv A Iofx Ag Uen Pre-installed for dowels, 80 x 8 mm, as commonly used in window manufacturing. Please refer to the detailed description in the attached PDF. The machine is available for demonstration in our showroom and ready for operation.