Edgebander

SCM minimax me 40tr

Condition: used, Year of construction: 2021, MEGA 300 TS Numerical Control Panel height 60 mm PVC/Abs mm 3 Feed speed up to 22 m/min Working height adjustable electronically by C.N. Motorized rubber belt with higher pressure Introduction system for small panels Panel support guide with electronic adjustment by C.N. Side roller conveyor with idle wheels for panel support Anti-adhesive group Rectifier unit with two motors electronically adjustable by C.N. Roll holder plate for delicate edges Edge magazine with 2 positions Gluing unit for EVA glue with glue tank and pre-melter Edge pressure group on straight profiles with pressure rollers electronically adjustable by C.N Non-stick group Trimming unit with 2 motors with automatic inclination adjustment Trimming unit with 2 superimposed motors Trimming / gleaning group with 2 tilting motors electronically adjustable by C.N. Rounding unit with 4 motors Edge scraper unit electronically adjustable by C.N. Glue scraper unit Oscillating brush group Hairdryer group Nsdpfx Ast Hal Dog Iolh

Condition: new, Technical data: Max saw diameter: 400 mm Min saw diameter: 250 mm Saw spindle diameter: 30 mm Scorer diameter: 120 mm Scorer spindle diameter: 20 mm Scorer on a separate engine Manual saw height adjustment Tilting saw at an angle from 0° to 45° Manual adjustment of the saw angle Nodpsv S Uz Iefx Ag Ijlh Carriage length: 3200 mm Carriage lock Work table: 1450 mm x 1030 mm Table height: 920 mm Table extensions 2 x Culaga Guard Safety switch Power supply: 380 V Main engine power: 7 kW Overall dimensions: Length: 3430 mm Width: 1900 mm Height: 1560mm

Condition: refurbished (used), Year of construction: 2017, functionality: fully functional, input voltage: 380 V, workpiece height (max.): 60 mm, edge thickness (max.): 8 mm, actuation type: electric, total height: 1,774 mm, total length: 4,580 mm, overall weight: 1,450 kg, Equipment: CE marking, documentation/manual, Workpiece thickness for edging: between 8 and 60 mm; edge thickness up to 8 mm depending on the unit. Components: - calibration, - edge feeding, - gluing, - end trimming, - milling group; flat or profiled milling of upper or lower edges, - profiling milling unit, - scraper group, - polishing station. Pressure bridge, infeed stop, control panel. Year: 2017. Refurbished in our workshop and inspected by a HOLZHER technician. Fitted with new diamond tools. Nledpfxjytp Hrj Ag Ish

Condition: new, Year of construction: 2026, Miter saw and cut-off saw, type: ZS 200 N - 5 KW motor with machine stand, but without saw blade Machine operated via handwheel and worm gear (rear) Tilting Saw blade diameter: 520 mm, saw blade arbor bore: 50 mm Saw blade speed: 2800 rpm 400 volts / 5 KW (S6/40%) motor with brake and automatic star-delta motor switching Cutting width at 90 degrees: 420 mm Cutting width at 45 degrees: when tilted: 295 mm Cutting height at 90 degrees: 200 mm Cutting height at 45 degrees when tilted: 140 mm The saw can be tilted to an acute angle of approximately 25 degrees on one side and tilted flat to the left up to 30 degrees. Nodpfxsi Dfido Ag Ielh Machine weight: approx. 250 kg Location: Available from stock in 54634 Bitburg - immediately available -

Condition: new, Year of construction: 2025, functionality: fully functional, ACTION M frame press Nodpfx Agswh T Dle Islh Press for any kind of window system: windows, slatted shutters, shutters and solid wood doors. Max working dimensions L x H 3500x2500 mm Min working dimensions L x H 250x375 mm Max vertical/horizontal thrust 7,4/2 ton Working height 480/1050 mm Hydraulic pump power 2.1 kW MACHINE COMPOSITION: ACTION M ACTION M FRAME PRESS num 1 109831 Normative CE per SM 1 R00494 action m 35-25 1 930731 Volt 400 EU 1 931201 Frequency 50 Hz 1 530074 PVC-coated beams working surfaces 1 530075 Intermediate manual crossbeam complete of piston and counter-stop 1 530076 Hydraulic system for low pressure working 1 530077 Equipment for trapezoidal products with oscillating head to adapt to the different corners of the windows system 1

Condition: as good as new (ex-display), Year of construction: 2023, machine/vehicle number: AH00004861, functionality: fully functional, operating pressure: 6 bar, temperature: 15 °C, NEW OPTIONAL SEMI-INDUSTRIAL EDGEBANDER SEMI-INDUSTRIAL WITH SIMPLIFIED CONTROL PANEL Make: SCM Model: K360 T-ER1 Year: 2023-2024 CE AH00004861 MACHINING CAPACITIES : - Panel height: 8 - 50 mm Thickness: 10 to 45 mm with use of rounding tool - Length of panel to be clad: 210 to 2500 mm - Minimum panel width: 90 to 1100 mm - Roll edge thickness: 0.4 to 3 mm without rounding max 3 mm with rounding - Strip edge thickness: max 6 mm without rounding max 3 mm with rounding - Edge width: panel thickness +2mm on each side - Drive (feed speed): 11 m/min - Workpiece spacing: 600 mm - Part protrusion from transfer chain (panel protrusion): 30 mm MACHINE COMPOSITION : - Reel table - Predisposition to receive an air-cushion table - Work table with front extension - Drive belt: chain - Non-stick spray unit - Edge straighteners (2 routers) rpm Diamond tools - Gluing unit with interchangeable tray Pneumatic pre-cutter Marouflage (pressing) with 3 rollers (1 motorized) - Chop-saw butt-cutting unit - Nesting copying top/bottom trimming unit - Rounding unit - Radius scrapers - Straight scrapers - Edge finishing spray device (Nebulization) - Textile polishing brush station - General power supply: 400v. Three-phase+N+T 50Hz Options installed on the machine : - 10.09.98 European safety standards (CE standards) - 63.05.29 Provision for an eventual air cushion plane at machine inlet - 62.15.02 "Nesting" copier kit - 62.12.03 "AAR" anti-stick group - 62.12.61 Nebulization device for edge finishing - 62.14.55 Diamond tools H=64 on grinding group - n.2 cuts - 62.15.06 "SGP-E" glue pot - Instead of the standard glue pot - 62.15.04 "RC-N" glue scraper group - 62.12.12 "SP-V" brush group Nljdpfettakhsx Ag Ieh Machine available : in stock

Condition: used, SCM 320cm SiX panel saw 320cm carriage, aggregate tilting in two directions +45 to -45 degrees, blade tilt and up/down adjustment with electric motor, rip fence on the right side with electric adjustment up to 1500mm, 2-axis scoring saw with electric adjustment, 7.5KW motor, speeds controlled by a frequency inverter, max. blade diameter 550mm, carriage with angle adjustment Nledszd Uf Tjpfx Ag Ijh used machine, good condition The machine has a new, non-original control system. All adjustments are functional.

Condition: excellent (used), Year of construction: 2009, machine/vehicle number: 241.125, functionality: fully functional, Horizontal Beamsaw of the manufacturer Schelling, designed for cutting wood-based material HPO – cutting optimization program Saw blade projection: max. 95 mm Saw carriage feed up to 120 m/min Cutting lengths: Model FH 4 430 - 4.300 mm Nodpjx Ebzdsfx Ag Iolh Can be inspected in working condition until beginning 2026. (dismantling planned) Maximum Saw blade Diameter - 350 mm Projection - 95 mm Clamp opening 90 mm Power Saw motor - 15 kW Scorer Diameter 300 mm Feed rate forward up to 80 m/min reverse 80 m/min Saw feed rate forward up to 120 m/min reverse 120 m/min

Condition: new, Year of construction: 2024, Martin T 54 jointer Only with a good surface planer can you create truly perfect foundations. The T54 was developed with precisely this objective in mind. It enables you to easily plane workpieces at the most modern level and to safely provide them with angular edges. The machine is equipped with a TERSA solid steel cutterhead as standard. The Xplane cutterhead, which operates with a drawing cut, is available as an optional extra. Planing bevels is effortless, as any angle between 90° and 45° can be quickly adjusted with the user-friendly one-hand adjustment. The solid cast iron tables of the T54 provide secure support even for large, heavy workpieces. If you need even more support, you can extend both the infeed and outfeed tables by 380 mm each - of course also in cast iron. Technical data table width: 500mm Nedpfx Aspgkmwog Islh Table length: 2840mm Maximum chip removal: 8mm cutter: diameter 125mm, 5000 rpm, Tersa Z4 Speed: 5000 rpm Motor power: 5,5kW fence adjustable up to 45 Auxiliary ruler for small workpieces Table adjustment motorized Equipment: T 54 T 5462-a Suvamatic T 541-a Tersa knife shaft 4 knives Location: Ex stock 54634 Bitburg - immediately available -

Condition: new, Year of construction: 2023, New machine Year of manufacture: 2023 Single-sided automatic edge banding machine with pre-milling unit, hot-melt adhesive application on straight workpieces (EVA/PUR glue pot with emptying function optional), HF cross-cut saw station, HF milling unit, corner copying unit, chain feed, double roller upper pressure, extendable workpiece support rail, signal lamp for workpiece tracking and integrated length control for contactless operation of processing functions. Suitable for ABS, PVC, melamine, and solid wood veneer edging coils, as well as fixed lengths from 0.4–3.0 / 6.0 mm and workpiece heights from 8–60 mm. Feed speed: 10.0 m/min; 8.0 m/min with corner copying. ● 3 free slots for finishing units ● 10" color touch screen. Machine length: 4030 mm Workpiece thickness: 8–60 mm Min. workpiece width: approx. 75 mm Min. workpiece length: approx. 120 mm (min. approx. 200 mm with corner copying) Edge thickness: 0.4–3.0 mm Pre-milling unit chip removal: 0–2.0 mm, stepless adjustment Total connected load: 7.5 kW – 400 V Feed speed: 10 m/min; 8 m/min Pneumatic connection: 6 bar Net weight: 1050 kg Nledpfx Aow I U Drsg Ieh Options: Surcharge for radius scraper unit with air nozzle + extraction Surcharge for surface scraper unit + extraction Surcharge for buffing unit EVA/PUR glue pot with emptying function Surcharge for diamond tools, height = 65 mm for pre-milling unit Riepe spray system (anti-adhesive) at the pre-milling unit Riepe spray system (cleaning spray before buffing unit) Pipe system with 90° bend + manual slide valve, installed on machine, D=200 mm Availability: short-term Location: Hochheim