Channel Bailing Press

PAAL PACOMAT 1S

Condition: ready for operation (used), Pressing force: approx. 700 kN (approx. 70 tons) Motor power: approx. 11 kW Power supply: 3 × 400 V / 50 Hz Single bale weight: up to approx. 600 kg Bale dimensions: approx. 1100 × 1100 × 1200 mm Fgodera Dddepfx Alqjb Machine dimensions: approx. 5.9 m length, 2.5 m width, approx. 2.6 m height Machine weight: approx. 7 tons Cycle time: approx. 45–47 s Construction features: - Large loading opening for cardboard - Possibility of automatic feeding (e.g., via conveyor) - Manual wire tying (4 wires) - Pallet lock and hydraulic doors for bale removal Advantages of this press: - Large bales – fewer transports - High pressing force - Designed for continuous operation Available production years: 2016–2020

Condition: not inspected (used), Year of construction: 1985, functionality: fully functional, pressing force: 50 t, bale length: 1,000 mm, bale width: 750 mm, bale height: 750,750,750 mm, bale weight: 500 kg, input voltage: 400 V, overall weight: 7,500 kg, oil tank capacity: 500 l, power: 30 kW (40.79 HP), empty load weight: 7,500 kg, input frequency: 50 Hz, Manufacturer: Paal Typ: Pacomat V Year of construction: 1985 Press power main press: 50 t Specific press capacity: 5 kg/cm² Fgedoic Rl Djpfx Alqob Feed channel: 1.000 x 720mm (l x w) Theoretic throughput rate: 200 cbm/h Bale size: 700 x 1.000 mm (w x h) length adjustable Driving motor: 30 kW Bale weight: approx. 500 kg Machine weight: approx. 8000kg The hydraulic unit is functional, the drive motor is in the removed state.

Condition: good (used), Year of construction: 2000, operating hours: 23,000 h, Bobst SP 142 CER II Fgjdpfsxxypyjx Alqjb

Year of construction: 2001, condition: ready for operation (used), A paving stone production line Omag, which has been continuously optimized and upgraded to the latest technical standards, is available. Overhauls: 1) Conversion for an additional hydraulic unit for additional load in 2020. 2) Conversion to servo-vibration with Siemens S7 control in 2016. 3) Conversion to digital path measurement of mould and ram in 2017. 4) New core filling carriages in 2017. Plant components: 1) Board destacker and board stacker including roller conveyor. 2) Board feeder (advance) and board conveyor (scraper) to the lifting frame. 3) Board turner. 4) Horizontal and vertical bundling units Ridder & Signode, years of manufacture: 1994 and 1983. 5) Trafo lifting platform including motors and without control, year of manufacture: 1983. 6) Doppler including hydraulic unit, year of manufacture: 2004. 7) Stone packer Omag K1400 including hydraulic unit, year of manufacture: 1997. The line has no base boards. 8) Stone finisher Omag S22 140-90, year of manufacture: 2001. Documentation available. An on-site inspection is possible. Fjdpew R Uziefx Alqjgb

Condition: used, material width 300 mm coil weight 3 t material thickness 2 - 4 mm Straightener, 7 rolls, Make. Schleicher, Type RM 6-95/160 - band width 300 mm - band thickness 2 – 4 mm - cross cut 1200 mm² - voltage 220/380 V 50 Hz - total power requirement 3,1 kW coiler with press roll, Make Schleicher, Type H-3 - Coil weight 3 t Fjdpscdrmmsfx Alqogb - Band width 400 mm - voltage 220/380 V 50 Hz - total power requirement 3,92 kW without control

Year of construction: 1955, condition: used, Radial drilling machine, drilling machine, boom drilling machine -Outreach: 2055 mm -Max. Distance from machine table to spindle mount: 1700 mm -Cone mount: MK5 Fsdpfxsd Enr Ij Alqjgb -Motor power: 7.5 kW -Speeds: 11.2-1400 rpm -Columns: Ø 450 mm -Spindle stroke: 540 mm -Thread cutting device -automatic feed: 0.037-2.0 mm/rev -Clamping area: 920 x 1600 mm -Dimensions: 2580/1110/H3450 mm -Weight: 6465 kg

Condition: reconditioned (used), machine/vehicle number: 550-235-ELD, GENERAL CHARACTERISTICS workpiece Ø max. 41 mm Range Module máx/min. 1,5 / 0.39 Rack face width 92 mm Manufacturing No. 550-235-ELD Fgsdsd Nw Ttepfx Alqob Máx/min. pitch form 20/40-32/64 Maximum stroke of tools trolley 760 mm Rack length máx. 610 mm ELECTRICAL CHARACTERISTICS Main motor power 15 Cv

Condition: reconditioned (used), Year of construction: 2007, operating hours: 22,605 h, functionality: fully functional, pressing force: 100 t, filling opening width: 1,100 mm, filling opening length: 1,600 mm, bale width: 1,100 mm, bale height: 1,100 mm, bale weight: 1,400 kg, overall weight: 36,000 kg, oil tank capacity: 1,300 l, For sale is a overhauled baler, with 100 tonnes pressing force, large format 1100 x 1100 mm, 75 kW drive power and 10-fold cross binding Technical data baler: Manufacturer Bollegraaf Typ HBC 110 K / 75 kW Year of construction 2007 Press power main press 100 tons Press power of pre-press 50 tons Operating hours 22,605 hours Feed channel 1,600 x 1,100 mm Capacity per cycle time 3,15 m³ Theoretic cycle time 19 sec. Bale size 1,100 x 1,100 mm Driving motor 75 kW Connected load 126 kW Full load current 238 A Tying system 5-fold vertical, 5-fold horizontal, fully automated Throughput rate at a bulk weight of 30 kg/cbm approx.16 tons/h bulk weight of 50 kg/cbm approx. 25 tons/h bulk weight of 100 kg/cbm approx. 47 tons/h Bale weight up to 1400 kg, depends on material and bale lenght Volume oil tank approx. 1,300 l SPS controller Telemecanique TSX Micro Operating panel Schneider MAGELIS Touch Baler dimensions built up with hopper 11,750 x 5,000 x 7,105 mm (l x w x h) Transport dimensions only baler 11.750 x 2.500 x 3.450 mm (l x w x h) Machine weight baler approx. 36 tons Comments: The press was partially overhauled and serviced in our workshop and tested and stored after completion of the work. The machine is available at short notice and can be inspected in our warehouse by appointment. The following overhaul work was carried out: Rust removal and partial painting of the press. Remaining hydraulic oil tank drained, oil filter and air filter replaced. New hydraulic oil topped up. All hydraulic hoses replaced. Main hydraulic cylinder, two cylinders of the prepress flap and the cylinder of the press channel dismantled, disassembled, checked, cylinder tubes honed, all seal sets replaced and a final pressure test carried out. Disassembly of the prepress flap with bearings and bearing blocks. 1st and 3rd circular arc segmet cut out and a new one welded in again. Fodpfxsvf E Ave Alqjgb Both bearings of the shaft of the prepress flap replaced. Upper material deflector on the frame of the prepress flap replaced. Press ram dismantled, checked and both front rollers replaced. Material deflectors and wear profiles on the sides and base of the press ram cut off and new ones welded in. Horizontal and vertical needle and tying unit dismantled, disassembled, checked, plastic sliding plates, bearings of the drill shafts and wire deflection rollers with bearings in the needle heads replaced. Both bronze slide rails on the left and right in the frame cover to the press ram replaced. Both wire deflection units on the left and right, with bale retaining clamps, completely renewed. Wire insertion unit including hydraulic cylinder under the needle feedthroughs completely renewed. Wire entry marks in the floor and side walls of the bale chamber welded shut and smoothed. General maintenance and service work carried out in accordance with the manufacturer's specifications. Press was tested in manual and automatic mode, accepted and stored after completion of overhaul work. We accept no liability for the technical specifications or any errors.

Condition: used, Year of construction: 1978, machine/vehicle number: 150 359 - 11683, functionality: fully functional, For sale are the PS160 (2 units) and the PS140 (1 unit). Fgodpjt Ucpbsfx Alqsb One is 250 metric tons, the other is 140 metric tons. The PS160 is one of the complete machines and is in operation; the PS160 does not have the control cabinet. The machines are for sale as a single unit and individually. Inquire by phone or email!

Condition: excellent (used), functionality: limited functionality, Year of construction: 2000, For sale: High-quality Liebherr concrete mixing plant in excellent condition – including BIBKO wastewater treatment system A used, excellently maintained concrete mixing plant from the renowned manufacturer Liebherr is for sale. The plant impresses with its low operating hours, complete technical documentation, and original delivery condition – all components come from the manufacturer itself. Important addition Also included in the offer is a wastewater treatment system from BIBKO Umwelttechnik & Beratung GmbH. This allows for environmentally friendly and economical reuse of residual and wash water, which not only reduces operating costs but also meets the ecological requirements of modern production processes. Main technical data Type: Ringtellermischer R 1.0 Practical mixing capacity: 1.0 m³ solid concrete per batch Efficient filling: A 6m³ truck mixer is filled in only 6 batches Theoretical mixing capacity: 50 m³/h Practical mixing capacity: 40 m³/h Aggregate storage Star storage: 1,200 m³ total capacity Active storage: 65 m³ Number of aggregate components: 5 Cement silos 2× cement silo at 40 t each with overfill protection Fjdpfxjwlwruo Alqogb 1× two-piece cement silo at 80 t with overfill protection Condition of the plant Commissioning: 2000 Out of operation: since 2006 Operating hours: approx. 3,500 (estimated) Condition: Very good – minimal use, excellently maintained Previous owner: First owner Originality: All components original from Liebherr Documentation: Fully available (electrical diagrams, foundation plans, structural analysis, etc.) The solid and well-thought-out construction of the plant enables easy disassembly and reassembly thanks to the predominantly bolted design. The control cabinets are connected to each other via plug connections – for details, please refer to the attached PDF documents. Additional service upon request: We are happy to support you in realizing your project with experienced partner companies for: Dismantling and reassembly Electrical commissioning (industrial electronics technician) Organization of transport with reliable forwarding agents This way, your new plant can be quickly and professionally put into operation at a new location. Interested? We look forward to your inquiry and are always available to answer any questions you may have!