Used Undercut for sale (27)

Condition: refurbished (used), functionality: fully functional, Panel Dividing System PA 4115 – 3100 x 3100 DNC-AT Condition: Completely overhauled Warranty: 1-year warranty Technical Specifications: Left-angle stop according to AGA 4383 Longitudinal Saw FM 16-3100: - Hardened guides - Automatic forward and return travel of the saw unit - Return travel with automatic lowering - Feed speed: 2–50 m/min (stepless adjustment via potentiometer) - Return speed: 70 m/min (rapid traverse) - Integrated extraction channels in the machine base and pressure beam - Scoring saw adjustable from outside (without opening the safety hood) - Saw unit with controlled DC drive: - Precise positioning (e.g. for cutouts) - Slowed extraction from the cut - Includes safety hood locking, SZ 5008 lamella curtain - Offcut device SP 5004 – Offcuts down to at least 5 mm - Main saw motor: 7.0 kW - Scoring saw motor: 1.1 kW (can be switched off separately) - Cutting length: 3100 mm - Cutting height: 70 mm - Dust tested: Threshold of 2 mg/m³ is significantly undercut - CE compliant Angle Pressure Device WP 5003: - With pressure claw for cross cuts - Adjustment range up to 2400 mm - Semi-automatic function Material Feed Table HP 5021 (mounted at rear of FM 16): - Parallel fence with 6 spring-loaded clamping fingers - Direct drive of material pusher via servo motor - Table surface with closed Pertinax panels (suitable for narrow strips) - Feed speed: 25 m/min (safety limited) - Return speed: 40 m/min - Table length: 3100 mm - Stop depth: 3100 mm Multi-microprocessor control Integrated PC with hard disk Operating system: LINUX Interfaces: serial + parallel, USB Network connectivity (also wireless LAN) Optimize cutting plans in the office and send directly to the machine Multitasking capable Printing function via USB Remote maintenance via Internet (Remote Desktop, TeamViewer) Multilingual dialog programming 15” flat screen + multifunctional keyboard Swiveling control panel Graphical representation of cutting plans and work processes Additional Equipment: Angle Stop Table HP 5043 (front mounted): - Machined steel angle, Pertinax table top - Table size: 1800 × 800 mm Workpiece Support Table HP 5025 (front mounted): - Pertinax surface - Table size: 1800 × 800 mm Air Cushion Device LK 5030 - Integrated into HP 5043 and HP 5025 Accessories: - 1 Circular saw blade KSB 4005 – Ø 305 mm, Z=60 (for main saw) Bodpfx Asxhg Ibsafjcu - 1 Circular saw blade KSB 4006 – Ø 200 mm, Z=60 conical (for scoring saw)

Condition: ready for operation (used), The U2PRW cutting and drilling machine is designed for processing slats and furniture fronts made of solid wood or MDF. The machine works in a semi-automatic cycle. During one cycle the machine performs: cutting at a given angle (in the range of 45 - 90 degrees) and drilling in the jammed plane, or the edge of the element. - Made in Poland TECHNICAL PARAMETERS: max. height of cut material 60 mm Bcsdpsq Ii Dlsfx Aafeu max. width of cut material at an angle of 45° 70 mm max. width of the material at an angle of 90° 150 mm max. length of cut material 2200 mm min. length of cut material at 45° 455 mm diameter of main saw 250 or 300 mm undercutter diameter 100 mm max. diameter of bottom milling cutter 35 mm max. depth of bottom milling 15 mm diameter of face drill embedment and bottom milling cutter 10 mm Drill head (face drilling): spindles 4 axial spacing of spindles 32 ; 32 ; 40 mm linear arrangement of spindles max. depth of face drilling 60 mm installed power 7 kW working pressure 0.6 Mpa overall dimensions (length / width / height) 4300 / 1600 / 1570 mm Machining units The machine is equipped with two machining units. The left unit, which is fixed, and the right unit - a sliding unit. Each machining unit consists of the following sub-assemblies - units: a main saw, an undercutting unit, a drilling unit that drills into the jammed plane, and a drilling unit that drills into the bottom of the workpiece. Bottom hole drilling unit The described aggregate is installed as an option. It is used in the processing of corner ties for doorframes with adjustable width. It makes a blind bore , for the can connector. The picture shows the mounted red cover which is at the same time the base for the machined angle strips and the cover with chip extractor. Workpiece pressure The machine tool is also equipped with a clamping system operating in two planes. The clamping area includes horizontal and vertical clamps. The horizontal clamps are responsible for pressing against the vertical bases and straightening the workpiece. Vertical ones, on the other hand, are responsible for immobilizing the workpiece during machining. The horizontal pressure always precedes the vertical pressure. Control The machine's control is clear, easy to use and functional. It allows switching on or off all aggregates separately, additionally with division into left and right sides. All aggregates have independent drive. The right-hand processing unit is set by pressing the control buttons on the control panel. The executive mechanism is a gearbox with an electric motor driving a trapezoidal screw. An electronic control system US with an operator panel and digital display is used to read and set the length of the workpiece. This system is also responsible for automatic corrections to the counter readings when the cutting angles change by 45° and 90°. In addition, it is responsible for automatic basing.

Condition: new, The powerful, mobile welding fume extractors AL-KO CLEAN UNIT F are the ideal solution for extracting welding fumes during manual welding, at automated welding stations, or with welding robots. Function: The welding fumes generated at the welding site are captured via extraction arms and hoods, among other means, and conveyed through a duct to the inlet of the AL-KO CLEAN UNIT F. In a large pre-separation chamber, coarse particles are first separated out. The subsequently arranged filter cartridges of dust class “M” filter out the remaining fine dust particles. During extraction operation, the differential pressure-controlled filter cleaning system removes adhering particles from the filter cartridges. Venturi nozzles on the filter cartridges maximize the cleaning efficiency, ensuring consistently high suction power and a long filter service life. A volumetric flow monitor continuously controls the required suction capacity and issues a warning if the nominal value is undercut. The collected dust is gathered in an easily mobile container. The cleaned air is recirculated into the room via the top of the unit. Applications: Bjdpowwkvqofx Aafscu - For all welding applications with unalloyed or low-alloyed steel - Usable as extraction at individual welding stations and at duct systems with several extraction points - Extraction at fixed-position hoods and welding tables Advantages: - Consistently high suction power thanks to an efficient fan and long-life cleanable filters - Extremely quiet due to high-performance sound insulation - Suitable for individual welding stations and for connection to duct systems - IE3 motors for high energy efficiency - Wide performance range - Optional accessories for various welding applications

Condition: ready for operation (used), Technical characteristics CNC ROVER A machining center BIESSE's Rover A series machining centers are specially designed for daily milling and drilling operations on panels, doors, component doors and furniture. The mobile gantry structure is made of extra-thick electro-welded sheet steel and stiffening hangers to minimize distortion during machining. For movement of the moving column along the longitudinal axis (X axis) and in the transverse direction (Y axis), BIESSE has opted for a rack-and-pinion solution, enabling higher acceleration and speed parameters than those achievable with a ballscrew. Controlled axis motors : Brushless motors, controlled by digital actuators. Hardened steel controlled axis guides. Automatic centralized lubrication system. Machine equipped with two vacuum pumps, 250 m3/h and 300 m3/h. Activation of vacuum and pneumatic systems is available from any point along the machine's X work zone. Working range (vertical electrospindle axis): X= 5540 mm Y= 1560 mm for 4 axes, 1570 for 5 axes Z= 230 mm with modules H=74 mm /Configuration 1B and 3B Z = 275 mm with modules H=29 mm / Configuration 1B and 3B 8 ATS aluminum worktops 1 X-axis metric ruler for correct positioning of worktops 8 metric rulers on Y axis for correct positioning of workpiece clamping systems 32 carriages 132 x 132 x H 41.5 mm Each carriage rotates the modules every 15° 32 plugs for closing the carriages Additional quick-fit connections for special jigs EPS (Electronic Positioning System) automatic positioning for worktops up to 1550 mm, allowing automatic positioning of clamping devices at selected points. An entire half machining zone can be positioned in hidden time while the machine is machining (avoiding major productivity losses). Each carriage is equipped with a blowing system to ensure that the machining plane on which it slides is always clean. 2 X-shaped machining zones Reference systems : Rear line stop with 115 mm travel Intermediate line stop positioned at 685 mm Front line stop positioned at 1348 mm 4 side stops with 140 mm travel (2 left and 2 right) 2 additional side stops (1 left and 1 right) 1 retractable linear stop for raw panels. Vacuum module 132 x 146 Vacuum module 132 x 75 Vacuum module 132 × 54 CFT system : Vacuum system for aluminum CFT modules, for left work area Aluminum vacuum module, dimensions : X=1250 mm, Y=625 mm, H=74 mm, for modular worktops With this solution, it is possible to prepare a continuous surface for thin/flexible panels or for nesting, bending, etc Uniclamp vice Support base 130 x 130 mm Flat disc 130 x 130 mm Bsdjtqi U Ijpfx Aafocu Double-movement Uniclamp vice Circular support base, diameter 130 mm Clamping workpieces thicknesses from 40 to 98 mm Horizontal vice, height 74 mm Chip and waste conveyor belt Configuration (3B) : Machining unit 5 axis 13kW electrospindle, up to 20000 RPM HSK F63 spindle Liquid-cooled C axis sewing : 360° continuous rotation Maximum undercut angle: -5°. Drilling unit BH 17 L drilling head Up to 17 independent tools Single and multiple drilling Work on all 5 faces of the workpiece and grooves with X-direction blade on the upper face. 10 independent vertical spindles, 32 mm centres 5 in X direction 5 in Y direction 3 opposite independent horizontal spindles, 32 mm pitch 2 in X direction 1 in Y direction 1 circular blade ⌀ 120 mm For groove in X direction (useful cut 25 mm) Multifunctional unit 1 circular blade ⌀ 300 mm 2 independent Z axes (1 for the electro-spindle and 1 for the drilling and multi