Used Section Bending Rolls for sale (12,099)

Condition: used, Year of construction: 2001, functionality: fully functional, Profile Bending Machine SAF Curvatrici (TUWI) DS 60 HV – Top Condition & Huge Tool Package Description: For sale is a high-quality profile bending machine, type SAF Curvatrici (TUWI) DS 60 HV, from the first owner. The machine was purchased new by us in 2001 and has been in our possession ever since. It is fully operational and can be demonstrated under power after prior consultation. Special highlight – Modernized control system (08/2019): The control system was completely overhauled and modernized by a specialist company in August 2019. Now, 10 different feed sequences can be programmed. After a programmed value is reached, the next value is automatically approached by pressing the button again (value input in ascending order). Technical data & equipment: • Shaft diameter: 50 mm (for all three axes) • Acceptance height: 115 mm • Additional equipment from factory: 2 RCD correction rollers for bending angle iron (R/L). The original, lateral and height-adjustable shafts (38 x 250 mm) are also included. • Special modification for transport: Specially manufactured base frame for transport including four height-adjustable support plates. Bodpfx Aez Ix Uksknolp • Additional device for angle iron: A 10 mm thick plate was mounted on the top side. An additional hydraulic cylinder can be attached here, which pushes the vertical flange extremely close to 90° during bending (adjustable pressure depending on the angle). Note: The cylinder is not included in the standard price, but can be requested separately. Enormous scope of supply (Extremely many tools included!): The biggest advantage of this offer is the extremely extensive tool package, which is completely included in the price: • Standard tools: Complete set according to the machine’s scope of supply • 18 different roller sets: According to the list from Ø 8 mm to Ø 33.7 mm • Special tools for angle iron (according to the list) • Special tools for flat steel (light & heavy axis) • Special tools for square and rectangular tubes • Special tools for diagonal square material • Documentation: Original operating manual is fully available Note: The machine will only be sold as a complete package together with the complete tool set according to the attached list. Sales and delivery conditions: • Pricing: Ex works (net, plus VAT). • Logistics: The disassembly, loading and collection must be organized and carried out by the buyer himself or by a forwarding agent commissioned by him. Technical specifications according to available documents. Subject to prior sale.

Year of construction: 2004, condition: like new (used), Profile bending machine hydraulic heavy duty -output shafts 360 mm Equipped with traction tooling for H-beam HEB IPE INP rolling on the hard-side Configuration -pyramid dual pinch side rolls independent hydraulic -3 rolls driven hydraulic and gear unit -synchro. -set of rolls for HEB beam – INP beam - flat bar square bar. -Set of heads for traction the HEB – INP beam bending on the hard side -Set of rolls for pipe bending. Pipe 20 inches max capacity. -Lateral correctors left/right side hydraulic operated in 3 directions -Add-on rollers angle bending & T-section leg-in / leg-out -Control panel console electric joysticks manual use & program automatic -Digital readout screen display 8 axis position reading of the rolls - 8 axis automatic programmable bending works -Electric Vac 400/50 ( rewirable on request ) -weight total of the machine approx. 65 Ton. -Hydraulic reservoir oil 1200 liters -High pressure hydraulic power unit multi pumps run on 100Hp electric motor . -Working speed variable slow-fast. -Emergency shut-down devices in compliance with safety requirement. -CE quality certification, Made in Italy manufacturing. -Service manuals and operation books along with the machine Bodpfx Akoiwa Hcenelp On request we supply additional set of rolls interchangeable to seat and bend the wanted profiles. Capacity table max.: – HEB 500 -INP 600 *-ANGLE 200 MM *-T300 MM *-20″ PIPE SIZE *-UNP 500 MM *-FLATBAR 300X80 MM *-SQUAREBAR 200 MM *-PIPE/TUBE UP TO 508MM see capacity chart in enclosed

Condition: excellent (used), functionality: fully functional, Year of construction: 2020, roller diameter: 60 mm, working width: 1,050 mm, sheet thickness (max.): 1 mm, roll metal bending machine Isitan 1050 X 1.2mm Manual 3 roll Bending Machine, excellent condition for sale manufacturer: Isitan 1050X1.2 max sheet width: 1050mm Blodpfowk Rlxsx Aknep max sheet thickness: 1.2 mm Wire grooves at the ends of the rollers Conical bender roller diameter: 60mm Upper roller removable for easy workpiece removal machine dimensions: length: 130cm height: 100cm width: 65cm weight: 240kg

Condition: used, Roundo PS340 3000 mm Hydraulic Double-Pinch Plate Bending Rolls Manufacturer: Roundo AB Model: PS340 Year: 1983 Country of manufacture: Sweden Type: Hydraulic three-roll double-pinch plate bending rolls Capacity Maximum working length: 3,000 mm Pre-bending capacity: approximately 12 mm mild steel aximum rolling capacity: approximately 18–23 mm mild steel, depending upon finished diameter Standard upper-roll diameter: 340 mm Plate capacities based upon mild steel of approximately 270 N/mm² yield strength Minimum rolling diameter: approximately 1.1–1.4 times the upper-roll diameter, depending upon material thickness Remaining straight edge after pre-bending: approximately 1.5–2 times plate thickness Features Hydraulic double-pinch design Both lower rolls independently hydraulically adjustable Pre-bending of both ends without removing and reversing the plate Hydraulic rotation of all three rolls Infinitely variable rolling speed Hydraulic powered drop end Portable pendant control Front safety trip bar Heavy-duty fabricated and stress-relieved frame Forged and crowned steel rolls Blsdpfxezuzpye Aknsp Rolls mounted in heavy-duty roller bearings Suitable for cylindrical and conical bending Approximate machine weight: 14,000–15,000 kg, subject to confirmation Approximate main motor: 22 kW, subject to data-plate confirmation

Condition: used, sheet width 3000 mm plate thickness 6 mm pre-bending 4 roll diameter 205 mm Blode Ahkinjpfx Aknop total power requirement 5 kW weight of the machine ca. 3,7 t dimensions of the machine ca. 4,0 x 1,4 x 1, 5 m Roundo 3-roll plate bending machine, featuring: - Hydraulic drop-end bearing and remote control - Conical bending attachment: a device for rolling cones and funnels.

Condition: new, sheet thickness: 25sheet length: 2600prebending: 20Upper Roll Diameter: 360Bottom Roll Diameter: 330Side Roll: 250motor: 18,5messurements (LxWxH): 5045 x 1900 x 1680weight approx.: 10780 Machine Features: - Separate, movable control panel - Digital position display for the side rolls - Fully welded steel machine frame (St-52) - Cone bending attachment - Bearing-supported rolls - Cone bending and position adjustment via the control panel - Induction-hardened rolls - Top and bottom (central) rolls driven by hydraulic motors and planetary gear reducers - Certifications: CE, ISO 9001:2015, TSEK and TURQUM Optional Accessories (upon request): - Infinitely variable rotation speed - Side and central supports for large diameters Blodpfxed Ab Rws Aknsp - Material feeding table - Material ejector - Interchangeable top roll - Oil cooling system - CNC control - NC control

Condition: used, Offered for sale is a hydraulic three-roll plate bending machine. Pre-bending capacity X/Y: 3000mm/15mm. Bending width: 3000mm. Reference material: Steel. Tensile strength of the reference material: 45-47kp/mm². Yield strength of the reference material: 25-27kp/mm². Equipped with hydraulically adjustable bottom rolls, hydraulic drop-end, plate support with vertical guide mast and support arm, and machine-mounted push-button control panel. Inspection possible by arrangement. Bjdpfxs Ad Nrle Aknelp

Condition: excellent (used), functionality: fully functional, Year of construction: 2024, actuation type: electric, roller diameter: 90 mm, working width: 1,270 mm, sheet thickness (max.): 3 mm, overall weight: 520 kg, power: 1.1 kW (1.50 HP), input voltage: 400 V, rotational speed (max.): 6 rpm, type of input current: three-phase, Equipment: cone bending device, emergency stop, foot remote control, hardened rollers, swiveling upper roller, sheet metal roll bending machine BOLUK BM 1270 x 90 - 2.5 mm NEW! for sale. manufacturer: BOLUK 1270X90mm year of manufacture: 2024 Bending Length: 1270 mm Bending capacity: 2.5 mm Roller diameter 90 mm Bsdpfxsxhub Ae Aknolp - SAE 1050 certified high tensile steel rollers - Wire grooves at the ends of the rollers (4/6/9) mm - Manually adjustable rear roller - Mobile control panel with foot pedal - Precision bending with brake motor - Conical bending device - Manually foldable end - Cast iron main frames Bending speed 6m / min Motor power 1.1 kW 50Hz 380v Wire groove diameter 4/7/10 mm Machine dimensions 1850x700x1200 mm Weight 520 kg

Condition: used, Machine type : Motorized bending roll Manufacturer : Bradbury Control unit : MCE (industrial electrical control panel) Supply voltage : 380 V Phase : 3 Frequency : 50 Hz FLA (Full Load Amperage) : 17.6 A Main motor FLA : 15 A Disconnect short-circuit rating : 200,000 A Internal short-circuit rating : 65,000 A Electrical diagram no. : ED3033 Electrical serial no. : B014541 Machine Application The Bradbury bending roll is used for rolling and forming sheet metal into precise cylinders, cones, or arcs. It is employed in the production of ducts, tanks, tubes, or metal shells, and can be integrated into profiling or cutting lines. Features / Differences – Dedicated MCE control panel, with high-capacity electrical protection (200,000 A). – Main motor rated at 15 A, operating on standard industrial 3-phase power. – Full electrical documentation under reference ED3033 for operation and maintenance. Bjdpfx Akow Dd Iyonslp – Compatible for integration within Bradbury automated coil processing lines.

Condition: used, sheet thickness: 1messurements (LxWxH): 170 x 55 x 110sheet length: 1050weight approx.: 300 3-Roll Plate Bending Machine Blodpfx Ao Agdagsknep Dimensions (L × W × H): approx. 170 × 55 × 110 cm Working width: approx. 1050 mm

Year of construction: 1973, condition: like new (used), Used BRONX Heavy Duty Initial Pinch Pyramid bending rolls. Year of manufacture : 1973. MACHINE FORMERLY INSTALLED AT ROLLS ROYCE PLC IN DERBY UK. IMMEDIATELY FOR SALE AND NOW LOCATED IN BELGUIM WHERE IT CAN BE INSPECTED. SPECIFICATION CAPACITY Two sets of dimensions which are shown below as "Prebending & Rolling" and then "Rolling only". Material Mild Steel Mild Steel Tensile strength 28/32 tons/sq.in 28/32 tons/sq.in Maximum width 11’(3350mm) 11’(3350mm) Maximum thickness at this width 2” (50mm) 2½” (63.5mm) Minimum inside diameter of rolled cylinder at maximum capacity 30’ (762mm) 37 ½’ (953mm) Maximum thickness of plate when hot rolling (finished rolling temperature 850° C.) 4” (102mm) 5” (127mm) Minimum inside diameter of rolled cylinder at maximum capacity hot rolling 40” (1016mm) 50” (1270mm) MAIN PARTICULARS Diameter of all rolls - 27” (686mm) Body length of rolls - 11’2”(3403mm) Rolling speed - 12 f.p.m. (3600mm/min) Main drive motor - 150 H.P. Slip Ring Type Two bottom roll adjusting motors, each - 50 H.P. Slip Ring Type Combined operation of swing down bearing and top roll counterbalance - Hydraulically applied Hydraulic power pack motor - 10 H.P. Electrical equipment to be suitable for operation on a supply of - 400/440 volts, 3 phase, 50 cycles CONE ROLLING ATTACHMENT: To facilitate the rolling of taper or conical forms, a skid plate is fitted to the inside of the non-drive end housing. ELECTRICAL EQUIPMENT Motors: Main Drive - 150 H.P. half hour rated – slip ring screen protected – foot mounted type. Bottom Roll Adjustments - 50 H.P. half hour rated – slip ring screen protected – foot mounted type. Hydraulic Power Pack Motor - 10 H.P. continuously rated – Squirrel cage – screen protected – foot mounted type. Control Gear: Main Drive - Drum type reversing control gear with 5 minute rated wire wound resistances, designed to pass 100% full load on the first notch or operating position in each direction. The controller will be fitted with off position interlock and limit switch rings where necessary. Bottom Roll Adjustments - Drum type reversing control gear with 5 minute rated wire wound resistances designed to pass 100% full load on the first notch or operating position in each direction. The controllers will be fitted with off position interlock and limit switch rings where necessary. Hydraulic Power Pack - Direct-on-line contactor type starter, operated from a maintaining type push button station. Solenoid valves for operating cylinders are push button operated. Note: Full protection to be provided for all the above control gear by a circuit breaker, incorporating overload and no-volt protection. FEATURES AND EQUIPMENT Spare Roll included with the machine. LENGTH TBA MM Bljdpfsh U Rzgox Aknop WIDTH TBA MM HEIGHT TBA MM WEIGHT 95 tonnes NOTE: The information contained herein is provided in good faith, but however due to unforeseen errors or omissions cannot be binding as to accuracy.

Condition: good (used), functionality: fully functional, Year of construction: 2010, control type: manual, actuation type: hydraulic, number of rollers: 3, sheet thickness (max.): 5 mm, sheet thickness stainless steel (max.): 3 mm, sheet thickness aluminum (max.): 6 mm, overall weight: 1,100 kg, Equipment: centralized greasing system, cone bending device, emergency stop, foot remote control, hardened rollers, swiveling upper roller, Bending length: 1.050 mm Bendingcapacity: 5.0 mm Steel Bsdpfxsz Tdg Dj Aknelp 3.0 mm Stainless steel 6.0 mm Aluminium Upper roll: Ø130 -> 75 mm Lower rolls: Ø130 mm Featured with: - Hydraulic drop end - 3-rolls driven - Hand-footcontrolled

Condition: used, Offered for sale is a hydraulic three-roll plate bending machine. Bending width: 3000mm. Pre-bending capacity: 31mm at 3000mm plate width. Reference material: Steel with yield strength of 240N/mm². Pre-bending diameter at specified capacity: greater than 630mm. Control system: Separate control panel with joystick control for roll and support adjustment. Equipped with hydraulically adjustable bottom rolls, overhead plate support, side plate support and hydraulically operated drop-end bearing. Inspection possible by arrangement. Bodpfj Ad Nq Uox Aknelp

Condition: used, Year of construction: 1989, Schäfer SVRM 3500/12 - CNC 4-Roller Plate Bending Machine - Siemens CNC control with joystick for roller positioning and digital display (upgraded in 2006) - Hydraulic tilting of the top roller via control panel - Rollers made of hardened material with a strength of 900 N/mm² - Year of manufacture: 1989 Technical Data - Max. sheet width: 3500 mm - Roller barrel length: 3550 mm - Max. sheet thickness (bending): 12 mm - Max. sheet thickness (pre-bending) 4xS/3xS: 8 / 6 mm - Max. yield limit of sheets at 20% cold work hardening: 380 N/mm² - Top & bottom roller diameter: 360 mm - Side roller diameter: 290 mm - Smallest achievable bending radius: 220 mm - Feed speed, bottom roller: 200 mm/min - Feed speed, side rollers: 700 mm/min - Total installed power: 22 kW - Electrical system: 380 V / 50 Hz / 3 Ph - Space requirements including control, hydraulics & roller conveyor (WxHxD): approx. 7900 x 3300 x 4600 mm - Pit depth: 900 mm Bsdpeylyh Dsfx Aknolp - Machine weight: 21,100 kg

Condition: new, sheet width 700 mm plate thickness 4,0 mm distance between columns 720 mm Bjdpswfyqysfx Aknolp diameter of upper rolls 95 mm total power requirement 1,1 KW weight of the machine ca. 0,37 t dimensions of the machine ca. 0,95 x 0,76 x 1,25 mm

Condition: new, sheet width 1070 mm plate thickness 3,0 mm distance between columns 1100 mm diameter of upper rolls 95 mm total power requirement 1,1 KW weight of the machine ca. 420 Kg dimensions of the machine ca. 1600 x 800 x 1200 mm Motorized sheet metal bending machine with: - Foot switch for left / right - manually adjustable rear roller - Hardened rollers - Conical bending - Swiveling top roller - Safety device emergency leash - Documentation currently only in English - 400V Bljdpfshfhzvjx Aknjp

Condition: used, Year of construction: 1986, sheet width 2040 mm plate thickness 4,0 mm distance between columns 2100 mm roll diameter 150 mm total power requirement 7,0 KW weight of the machine ca. 2,2 t dimensions of the machine ca. 2,95 x 1,0 x 1,75 mm Sheet metal bending machine with 3 rollers - 2 driven rollers - Rear roller electrically adjustable - Conical bending - Foot switch - Emergency stop device Bledpfx Akoy Ezzyjnsp

Condition: good (used), Year of construction: 1989, sheet width 2050 mm plate thickness 8.0 mm pre-bending capacity 6.0 mm upper roll diameter 190 mm lower roll diameter 180 mm bending speed 5.2 m/min work height max. ca. 980 mm total power requirement 5.5 kW weight of the machine ca. 3500 kg. Bsdpfx Aez Dkzhoknelp range L-W-H 2900 x 1200 x 1280 mm Furnishing: - Robust electro-hydraulic 3-roller bending machine - planetary movement of the bending rollers with reduced center distance - Hydraulic motors combined with planetary gears * for driving the 3 rollers - mobile operating unit, with connection cable + plug - extended roll ends for profile bending rolls - with conical bending device * Inclination of the side rollers by handwheels * Workpiece limitation for a cone with a 45° pitch: * Working length max: 60% * Bending capacity max: 50% - free-moving operation * electric delivery rollers * electric turning/rolling movement * digital position display of the reels - hardened rollers SAE 1050 CK 45 - Hydraulic folding store for removing closed pipes - safety device (cable) - Original instruction manual + CE declaration * Machine link : ?machineno=1008-9401255

Condition: good (used), Technical specifications: Working width: 4050 mm Max. bending capacity: 6.0 mm Max. pre-bending: 4.0 mm Top roller diameter: 210 mm Side lower roller diameter: 210 mm Middle lower roller diameter: 210 mm Bljdpswkaalsfx Aknjp Conical bending device by tilting the two side rollers Hydraulic folding bearings Pivoting control panel with digital display Dimensions (length x width x height): approx. 6900 x 2300 x 1800 mm Weight: approx. 14 tons The seller is not liable for typographical or data transmission errors. The machine's appearance, technology, and wear are consistent with its age; used machines are sold without any warranty.

Condition: new, sheet width 1000 mm plate thickness 3,3 mm distance between columns 1050 mm diameter of upper rolls 90 mm total power requirement 1,1 KW weight of the machine ca. 0,445 t dimensions of the machine ca. 1,5 x 0,9 x 1,25 mm Sheet metal bending machine with special dimensions: - Capacity 1000 x 3 mm - Conical bending Bedpsrb Hcbofx Aknelp - Swing-out top roller - Emergency release safety device - Documentation - 400V

Condition: refurbished (used), BENDING ROLL MACHINE SHEET METAL LENGHT 4000mm SHEET METAL THICKNESS 15mm 3 BENDING ROLLS PREBENDING Bedpfx Ashxyiljknelp WEIGHT: 23.000kgr THE MACHINE IS IN TOP CONDITION LIKE NEW NEW ELECTRIC PANEL, NEW ELECTRIC CABINET, NEW CABLES, NEW SEALS, MOTOR AND PUMB RESTORATION

Condition: new, sheet width 1000 mm plate thickness 3,3 mm distance between columns 1050 mm diameter of upper rolls 90 mm total power requirement 1,1 KW weight of the machine ca. 0,39 t dimensions of the machine ca. 1,4 x 0,9 x 1,2 mm Blodpfx Aorb Hcfsknep Sheet metal bending machine with special dimensions: - Capacity 700 x 4 mm - Conical bending - Swing-out top roller - Emergency release safety device - Documentation - 400V

Condition: new, sheet width 1070 mm plate thickness 4 mm distance between columns 1100 mm diameter of upper rolls 110 mm total power requirement 5,0 KW weight of the machine ca. 1,2 t Bedpfevki E Ssx Aknelp dimensions of the machine ca. 2,0 x 0,9 x 1,1 mm

Condition: new, sheet width 2070 mm plate thickness 4 mm distance between columns 2100 mm Bodpfx Aefv H A Usknslp diameter of upper rolls 140 mm weight of the machine ca. 0,37 t

Condition: new, Year of construction: 2024, neu 2024 9722 prompt, Zwischenverkauf v Türkei 17300 € 332.16 € 1 2050 mm 3 mm 130 mm 3,5 m/min 2.2 kW 3200 mm 750 mm 1000 mm 1500 kg 3 rolls asymmetric rolls - prebending 2 rolls driven by brakemotor HARDENED ROLLS Bodpfxewiqpbe Aknolp manual Back Roll forward tiltable upper roll forward and reverse revs conical bending by tilt of backroll movable control panel users manual in GERMAN OPTIONS (PRICES ON REQUEST): (time of delivery with options approx. 8 weeks) Motorised Back Roll (Power Rear Roll) Digital Read-Out