Used Promac Fx 380 for sale (4,513)

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, empty load weight: 3,810 kg, maximum load weight: 34,190 kg, overall weight: 38,000 kg, axle configuration: 3 axles, total length: 12,660 mm, total width: 2,550 mm, suspension: air, tire size: 385/55 R22,5", tire condition: 100 %, Customized Transport Solution Configure your Fliegl vehicle to meet your specific requirements. The vehicle shown is an example. Production and equipment are customized according to customer specifications. Chassis for semi-trailer containers Fine-grained steel welded construction, semi-trailer plate with replaceable kingpins Container mounts: 1 x 40-foot with gooseneck tunnel Transport of filled tank containers is not permitted. Without rear height adjustment and without foldable center supports, transport of containers without a tunnel is not possible. Front container guide, plug-in type 24-ton, 2-speed support jack, single-sided operation, with straight lower section, without thrust compensation Wheel chocks with holders Aluminum side impact protection Galvanized steel underrun protection Half-shell fenders With anti-spray flaps per EC Rear bumper Axles + Suspension SAF disc brake axles with 430 mm disc diameter Axle/chassis laser-measured to reduce tire wear and fuel consumption Offset wheelbase mm (combined transport) up to 44-ton gross train weight Air suspension 1st axle: automatic lift axle, including forced lowering and start-up assist, operated by 3 brakes (start-up assist is functional up to a 30% axle load exceedance and up to a maximum speed of 25 km/h) Brake system Nsdpji Ri Ayefx Alnocu 2-line air brake system; color-coded lines for easy servicing. Spring-loaded parking brake EBS, Electronic Braking System with front EBS socket, without connecting cable Warning: The trailer may only be towed by vehicles that ensure the effectiveness of the ABS! With lift & lower valve Vehicle stability control system Axle load detection via EBS CAN bus signal, for display in the cab; truck must be equipped accordingly; no truck installation required. Wheels and tires 385/55 R22.5, brand selected by the manufacturer Steel rims, factory silver Electrical System 24 volts, multi-chamber lights, LED taillights and brake lights, yellow LED side lighting 2 white front position lights 2 white/red rear lane-marking lights 1 x 15-pin socket at the front, without connecting cable LED work lights on both sides (activated via reverse light) Additional LED work light(s) at the rear, activated via reverse light Operating Instructions The specified gross weight is technically possible; however, depending on the load, the gross weight may not be achieved while complying with the permissible axle, support, and fifth-wheel loads Special permit required if the total train length exceeds 16,500 mm Caution: Transport of filled tank containers is prohibited! Country of registration/plates Germany With DEKRA approval and certificate (per §13 EC - FGV) Prepared for single-line license plate holder Warning sign per ECE - 70 Contour marking with reflective strips per ECE R 048, white on the sides and red at the rear Paint finish Frame DB 7350 Novagrau *10-year warranty against rust-through* or hot-dip galvanized *15-year warranty against rust-through* Support legs black coated Customized transport solution Configure your Fliegl vehicle to meet your requirements. The vehicle shown is an example. Production and equipment are customized according to customer specifications.

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, empty load weight: 3,800 kg, maximum load weight: 34,200 kg, overall weight: 38,000 kg, axle configuration: 3 axles, total length: 13,500 mm, total width: 2,550 mm, suspension: air, tire size: 385/55 R22,5", tire condition: 100 %, Customized transport solution Configure your Fliegl vehicle according to your requirements. The vehicle shown is an example. Production and equipment are tailored to individual customer needs. Chassis, Saddle, Container Fine-grain steel welded construction, saddle plate with 2 replaceable kingpins Container receptacles: 1 x 40 ft with gooseneck tunnel, front extension extended: 1 x 45 ft with long gooseneck tunnel and rear overload The transport of filled tank containers is not permitted. Without rear height adjustment and without folding center supports, transport of containers without a tunnel is not possible. 2 container guides, incl. connection plate for electrical, air and brake connections (connections positioned upwards) Front extension mounted on rollers, manually extendable (for 45 ft containers with long tunnel) 24 tons, 2-speed support legs, single-side operation, with straight lower part, without extension compensation Wedge blocks with holder Aluminum side impact protection Galvanized steel underrun protection Extendable underrun protection for 45 ft containers Half-shell fenders with anti-splash flaps according to EC Rear impact protection Axles + Suspension SAF disc brake axles with 430 mm disc diameter Axle/chassis laser-aligned, reducing tire wear and fuel consumption Offset axle spacing mm (combined transport) up to 44 tons gross vehicle weight Air suspension Braking system Nedpfx Aoi Riwmjlnecu 2-line compressed air braking system, color-coded lines for easy servicing Spring brake parking brake 2 fail-safe coupling heads at the front, without connection cable EBS, electronic braking system with EBS socket at the front, without connection cable Test connection for brake cylinder pressure placed on the outside of the EBS module Note: The trailer may only be pulled by towing vehicles that ensure the effectiveness of the ABS! with lifting and lowering valve Vehicle - Driving stability system Axle load recognition via EBS-CAN bus signal, for display on the display in the driver's cab, the truck must be appropriately prepared, no truck installation (no calibrated scale) Wheels and tires 385/55 R22.5, manufacturer's choice Steel rims, factory silver Electrical system 24 Volt, multi-chamber lights, rear and brake lights in LED, yellow LED lighting on the side (Note! with certain towing vehicles, false diagnoses may occur, even if the function is given) 2 white position lights at the front 2 white/red side marker lights at the rear 2 x 7-pole fail-safe sockets at the front, without connection cable Operating instructions Note: Transport of filled tank containers is not permitted! When transporting 45 ft containers with a short tunnel, with or without a front extension, the permissible system length from kingpin to the rear edge of the vehicle and the total train length of 16500 mm will be exceeded! The underrun protection must be manually extended! An exemption permit according to § 70 StVZo is required! Country of registration / Signs Germany Type approval according to EC 2007/46 24/7 service hotline Prepared for single-row license plate holder Warning sign according to ECE - 70 Contour marking with reflective strips according to ECE R 048, white on the side and red at the rear Paint finish Frame DB 7350 Novagrau, 10 years warranty against rust-through Support legs black coated without pallet box paint Note: Archive images!

Condition: new, Year of construction: 2021, functionality: fully functional, Ladies and Gentlemen, Brand new Erhardt+Leimer web edge control systems are for sale, which have been installed but have not been used to this day. Ultrasonic edge sensor POE FX 46: Compact ultrasonic edge sensor with digital evaluation Measuring range ±3 mm Insensitive to contamination by dust Scanning soundproof materials such as paper, plastic and metal foils regardless of material transparency Internal temperature compensation for stable operating point Bar display to show the current edge position or diagnostic information PoE interface to the data network center _____ FR 6011 broadband sensor infrared: digital, measuring range +/- 79mm, clear width 40mm, with cable 3000mm long with cable gland M16x1.5 and JST female connector 00367440 More details on request. Current delivery time according to E+L: approx. 10-12 weeks after receipt of order or payment in advance _____ Web guides/web edge control as shown, including monitor Ncedji Hl Hhjpfx Alnju Production date is mid/end of 2021 (see type plates). 7x DRB14 rotating frame system EL.NET for controlling a running web, with digital position controller with touch display. Including connection cable. Sensor type: FR 6011 IR broadband sensor Nominal width: 250 mm Roller diameter: 60 mm web tension max.: 300 N Correction path max.: 42 mm If you need more precise data, please ask us or give us a call.

Condition: ready for operation (used), Year of construction: 2012, functionality: fully functional, Equipment: CE marking, Model Accord 30 FX Year November 2012 - First time installed in 2013 Nedpfxozbz Htj Alnscu Machine type 3-axis CNC machining center for solid wood, doors, windows, stairs, and joinery Working feld: X 3680 by Y 1680 mm. Z-axis travel 250 mm BRC multifunction unit for cutting, routing and boring both vertically, specially for production of the doors. DUO HT 12 Machining Head Syncron 8 Frontal and rear row of stops H50 for plates Prearrangement for clamps and for pneumatic clamps for plate Automatic positions system for placemant of the support beams and vacuum cups. 16 adjustable suction cup H50 145x145 mm. 8 adjustable suction cup H50 145x55 8 adjustable suction cup H50 180x65 Nr 8 Lifting supporters Motoriserd belt for wastes removal. Main electro spindle power 12 kW Maximum spindle speed 20,000 rpm Tool holder HSK-F63 Tool changer for 12 tools Vertical drilling spindles 10 X-Y rapid speed Up to 90 m/min Vacuum pump capacity 250 m³/h Maximum workpiece height 250 mm Supplementary base for bar Matic TecPad mobile console Pro-Speed Safety system XiLog Maestro soft wear Approximate machine weight 5 000 kg Volt 400 AC 50 Hz This machine still is in daily use to the end of week no. 24 Machine first time installed in 2013 and it is working on its orginal place. Come from Norway also low number of workin hours during the years. Rekman Maskin & Service - service of cnc woodworking machines since 1986

Condition: used, mileage: 722,472 km, power: 279 kW (379.33 HP), first registration: 07/2008, fuel type: diesel, empty load weight: 8,020 kg, maximum load weight: 9,980 kg, overall weight: 18,000 kg, tire size: 315/80 22,5, tire condition: 50 %, axle configuration: 4x2, wheelbase: 3,700 mm, color: white, driver cabin: sleeper cab, gearing type: automatic, emission class: euro5, suspension: steel, Year of construction: 2008, operating hours: 722,472 h, front tire size: 315/80 22,5, rear tire size: 315/80 22,5, Equipment: ABS, air conditioning, cruise control, differential lock, hydraulics, onboard computer, truck registration, Reference number for inquiries: 69262 Scania R 380 * Year of manufacture: 2008 * ABS (Anti-lock Braking System) * Air conditioning * Cool box * Air suspension * Cruise control * Tipping hydraulics * On-board computer * Differential lock * Low noise emission * Long-distance haulage > 7.5 t * Radio/CD player * CB radio * Electric windows and mirrors * Transmission type: Automatic * Suspension: Leaf spring * Gross vehicle weight: 18,000 kg * Unladen weight: 8,020 kg * Payload: 9,980 kg * Permitted gross weight: 18,000 kg * Tyre condition, 1st axle: 50% -- 50% - Tyre size: 315/80 R22.5 * Tyre condition, 2nd axle: 60%|60% -- 40%|40% - Tyre size: 315/80 R22.5 * Wheelbase: 3,700 mm * Tyre dimensions: 315/80 R22.5 * Twin-circuit hydraulics * Roof beacons Liability disclaimer: Subject to change, prior sale and errors excepted. More photos and videos are available on our website. Our comprehensive services include, for example: * Purchase / sale / rental of commercial vehicles * Fast and straightforward financing solutions * Assistance with all (export) documentation * Provision of export and customs license plates * Vehicle preparation: new tarpaulins, livery, painting, etc. Nodpfx Alexuzyxenjcu * Professional loading and load securing * TÜV inspections, registration service * Nationwide and international vehicle delivery Feel free to contact our trained staff—we are happy to advise you.

Condition: excellent (used), Rotating chuck Diameter: 100 mm Length: 380 mm Width: 160 mm Thickness: 32 mm Weight: 4 kg Ncodpfx Aoln Ukcolnou Other sizes available upon request.

Condition: used, mileage: 474,484 km, first registration: 10/2010, Year of construction: 2010, RENAULT PREMIUM 380 DXI BDF Flatbed with Palfinger Crane PK 12001 and Steerable Lift Axle ● Power: 286 kW / 390 hp ● Displacement: 10,837 cm³ ● Emissions standard: EURO 5 ● Axle configuration: 6x2 ● 3rd axle can be lifted, steerable ● Differential lock ● Engine brake ● Retarder ● Air conditioning ● Electric windows ● Electrically adjustable, heated exterior mirrors ● Radio / CD ● Central locking ● Gross Vehicle Weight (GVW): 26,000 kg ● Unladen weight: 11,170 kg ● Wheelbase: 5,300 mm ● Trailer hitch preparation ● Suspension front/rear: Air/Air ● Front axle tyres: 315/80 R22.5 ● Rear axle 1 tyres: 315/80 R22.5 ● Rear axle 2 tyres: 315/80 R22.5 ● Tyre tread depth: 13/14 / 11/11 / 10/10 / 10/13 / 5/4 mm Body: Gergen - Jung ● Type: JWLA ● BDF platform body with subframe ● Body dimensions: 7,100 x 2,550 mm Crane: Palfinger ● Type: PK 12001 EH S106-EK-A ● 4 boom extensions (3 hydraulic + 1 mechanical) ● Slewing drive ● Load hook ● Remote control ● Year of manufacture: 2010 ● 2 hydraulic outriggers sideways ● Emergency stop switch Ncodpfx Alox Nc Uioneu - German vehicle! - 1st owner - TÜV / Safety Inspection / UVV: NEW! Errors and prior sale excepted! = Further information = GVW: 26,000 kg Please contact Joannis Arpantzanis or Kai Bühler for further information.

Condition: used, functionality: fully functional, Year of construction: 2006, - Machine in good technical condition - Immediately available Nodpjzbypmofx Alnscu - Wide selection of attachments available as an option

Condition: used, mileage: 433,000 km, power: 279 kW (379.33 HP), first registration: 09/2014, fuel type: diesel, overall weight: 26,000 kg, axle configuration: 3 axles, color: red, gearing type: automatic, loading space length: 6,750 mm, loading space width: 2,530 mm, loading space height: 600 mm, Year of construction: 2014, Equipment: ABS, air conditioning, crane, Renault K 380 / 6x4 PLATFORM 6,75 m + CRANE + REMOTE CONTROL Accident-FREE IN GOOD CONDITION! ? YEAR OF PRODUCTION: 2014 ? MILAGE: 433 000 km EQUIPMENT: ? ABS Nedpsxbmz Iofx Alnjcu ? C. LOCKING ? EL. WINDOWS ? EL. MIRRORS ? AIRCONDITION ? POWER STEERING ? TACHOGRAPH TIPPER: 675 x 253 x 60 cm (L x W x H) CAPACITY: 12 000 kg TOTAL WEIGHT: 26 000 kg WHEELBASE: 490/135 cm TIRE SIZE: 13R22,5 SUSPENSION: SPRING CRANE: HIAB 166 BS - 3 HIDUO + REMOTE CONTROL TEL: KUBA - POLSKI, ENGLISH, DEUTSCH, ITALIANO SEBASTIAN - POLSKI, DEUTSCH, ITALIANO, ????? LASZLO - MAGYAR COSTEL - ROMÂN? (Romana facem toate formalitatile pt export inclusiv nr) Ref. nr: 00124

Condition: new, functionality: fully functional, machine/vehicle number: WFDFLT33802037879, empty load weight: 3,250 kg, maximum load weight: 34,750 kg, overall weight: 38,000 kg, axle configuration: 3 axles, total length: 6,790 mm, total width: 2,550 mm, suspension: air, tire size: 385/55 R22,5", tire condition: 100 %, available in multiple units Chassis, semi-trailer, container Fine-grain steel welded construction, kingpin plate with replaceable 2" kingpin Container fittings: 1 x 20 ft, flush at the rear (Note: low drawbar load with 20 ft container) 24 tons, 2-speed landing gear, single-sided operation, with semi-circular base and straight connection plate, with stroke equalization 2 support wedges with holder Rear underrun protection, steel Spray flaps at the rear, covering the entire width Half-shell fenders with anti-spray flaps according to EC Storage box for fire extinguishers up to 6 kg Fire extinguisher (ABC powder 6 kg) incl. stainless steel drip tray in the center of the rear container crossbeam, approx. 290 mm wide Axles + Suspension BPW disc brake axles, with 430 mm disc diameter "Axles/chassis laser-aligned" - reduces tire wear and fuel consumption Axle spacing offset 1410/1310 mm (combined transport), up to 44 tons total weight Air suspension 1st axle, automatic lift axle, including forced lowering and start assist, activated by "pressing the brake pedal 3 times" (start assist is functional up to an axle load exceedance of 30% and up to a speed of max. 25 km/h) Ncsdpezbtnijfx Alnsu Braking system 2-line pneumatic braking system Color-coded line routing for easy servicing Spring brake parking brake 2 tamper-proof coupling heads at the front, without connecting line 24-volt EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lift and lower valve Vehicle - driving stability system Axle load detection via EBS-CAN bus signal, for display on the dashboard in the cab, truck must be prepared accordingly, no truck installation (no calibrated scale) Wheels and tires 385/55 R22.5", manufacturer at the discretion of the manufacturer Steel rims, factory silver Electrical system 24 volts, multi-chamber lights, yellow LED lighting on the sides 2 white position lights at the front in LED 2 white/red marker lights at the rear 1 x 15-pin socket at the front, without connecting cable Operating instructions The specified total weight is technically possible; depending on the cargo, the total weight may not be reached while complying with the permissible axle/support and drawbar loads. (Poor driving and handling characteristics possible due to incorrect load distribution) Country of registration/plates Germany with Dekra inspection and certificate (according to §13 EG - FGV) 24/7 service hotline prepared for single-row license plate holder Warning sign "A" for waste transport, foldable ADR approval according to FL/AT with ADR warning sign at the rear Contour marking with reflective strips according to ECE R 048, white on the sides and red at the rear Paintwork Frame RAL 2011 traffic orange "10-year warranty against rust-through" Support feet black coated available in multiple units

Condition: good (used), mileage: 435,932 km, power: 279 kW (379.33 HP), first registration: 05/2011, fuel type: diesel, axle configuration: 6x2, fuel: diesel, brakes: engine braking, color: red, driver cabin: day cab, gearing type: automatic, emission class: euro5, suspension: steel-air, Year of construction: 2011, Equipment: AdBlue, air conditioning, central locking, cruise control, electric window regulation, fog lights, power mirror, soot filter, spoiler, Technical information Number of cylinders: 6 Axle configuration Brakes: disc brakes Front axle: Steering Rear axle 1: Double wheels Rear axle 2: Lift axle; Steering Weights Empty weight: 11.940 kg Carrying capacity: 14.060 kg GVW: 26.000 kg Condition Technical condition: good Visual appearance: good Additional information Please contact Arie or Pedro for more information = Additional options and accessories = - Air suspension Ncsdpfx Aloza Uh Ienou - Aluminium fuel tank - Heavy duty engine brake - Particulate filter - Radio/cassette player - Radio/CD player - Roof spoiler - Speed limiter - stand airco - Visor

Condition: excellent (used), mileage: 281,375 km, power: 266 kW (361.66 HP), first registration: 11/2012, fuel type: diesel, tire size: 315/80 R22,5, axle configuration: 8x4, fuel: diesel, driver cabin: day cab, gearing type: mechanical, emission class: euro3, suspension: other, total length: 8,300 mm, total width: 2,550 mm, total height: 3,100 mm, Year of construction: 2012, Equipment: ABS, airbag, electric window regulation, power assisted steering, = Additional options and accessories = - Leaf suspension - Television - PTO (power take-off) - Sun visor = Remarks = TRANSPORT TO ANTWERP 590 EURO = Further information = Tyre size: 315/80 R22.5 Front axle 1: Steered; Suspension: Parabolic spring Front axle 2: Steered; Suspension: Parabolic spring Rear axle 1: Twin tyres; Suspension: Leaf suspension Rear axle 2: Twin tyres; Suspension: Leaf suspension Njdpfjza Igqex Alnocu Technical condition: very good Visual condition: very good Reference number: 77

Condition: reconditioned (used), Year of construction: 2018, machine/vehicle number: 0-261-71-2126, functionality: fully functional, Equipment: documentation/manual, Element feeding and retrieval - Clamping beam with clamping strip - Preparation for connecting a return system - Variable feed rate: 8-18 m/min Ncjdpfxeza D E Aj Alneu - Automatically adjustable guide rail for groove, height of clamping beam, and clamping zone Edge banding - AQ65 glue pot - PUR pre-melter, 8 kg/h - Finishing of the element - Anti-adhesive and cleaning fluid - Unit for processing corners with a double profile FLEXTRIM - Cutting unit - Multifunctional unit for profiling with R-2 and R-1 tools - Edge milling unit with R-2 and R-1 tools - Flat profiling, polishing unit (top and bottom) Documentation - Selected languages: Croatian - Format: Data carrier + paper documentation General information - Control system: HOMAG POWERTOUCH control system - CE marking: YES - Commissioning status: Pending – planned date: June 2026 - Machine length: 6075 mm - Year: 2018 - Number of processed meters: 2.5 million

Condition: new, functionality: fully functional, machine/vehicle number: WFDFLT33801013475, empty load weight: 7,180 kg, maximum load weight: 28,820 kg, overall weight: 35,000 kg, axle configuration: 3 axles, loading space length: 13,650 mm, loading space width: 2,480 mm, total length: 13,850 mm, total width: 2,550 mm, suspension: air, tire size: 235/75 R17,5", tire condition: 100 %, color: silver, available in multiple units Fine-grained steel welded construction, kingpin plate with replaceable 2" kingpin, additional splash guard riveted to the underside as a sheet of metal, in the neck area above the rear axle of the semi-trailer and above the wheels on the vehicle, frame in reinforced design for vehicle loads up to the outer frame, outer frame with "Load-Lock profile" approximately every 400 mm for securing lashing straps, 10 pairs of lashing rings embedded in the top/outside of the outer frame, each rated at 10 tons, 24 tons. Two-stage support winch, single-side operation, with semi-circular lower part and straight connecting plate, with stroke compensation, folding rear support, support wedges with holder, aluminum side impact protection, steel under-ride protection, quarter panel fenders in front of and behind each axle, with additional sheet metal splash guard above the wheels, with anti-spray flaps according to EC regulations, 1 plastic toolbox, w=600 / h=425 / d=460 mm, lockable, container locking system, 4 pairs of locking recesses embedded in the floor for 2 x 20 ft or 1 x 40 ft containers, 4 pairs of container locking adapters, (additional transverse support required at the front and rear of the container, the container must rest evenly over its width in conjunction with the locks, transverse supports are not included in the scope of delivery), attachment rail for loading ramps at the rear extension over the entire width, rear extension mechanical, with hand crank, extendable by approximately 1,500 mm, lockable every 500 mm, including under-ride protection with lighting that can be extended, in the wheel well area with Lohr sheet metal, center with steel diamond plate, storage space for loading ramps integrated in the rear extension, usable only when the rear extension is extended by approximately 1000 mm, for transporting the ramps with the rear extension retracted - storage space for ramps in the FR, located to the right in front of the axles. 1 pair of ramps, 3,000 mm long, 300 mm wide, load-bearing capacity per pair 6,000 kg, electric cable winch, 24 volts, pulling force approximately 8165 kg, mounted centrally at the very front, operated with a wireless remote control, cable length 35 m x approximately 10 mm, with roller cable guide and removable guide rollers. Ncedpfx Aoza Aiyelnou Axles + Suspension: SAF/BPW drum brake axles, at the manufacturer's choice, air suspension, 1st axle automatic lift axle, additionally electrically operable from the truck, including forced lowering and starting aid. Braking System: 2-line pneumatic braking system, color-coded line routing for easy servicing, spring-loaded parking brake, 2 tamper-proof coupling heads at the front, EBS, electronic braking system with EBS socket at the front, without connection cable, with raising & lowering valve with quick vent, holding function in lowered position + auto-reset function, vehicle stability system, axle load recognition via EBS-CAN bus signal. Wheels and Tires: 235 / 75 R 17.5", manufacturer's choice, steel rims in twin arrangement. Electrical System: 24 volts, multi-chamber lights in LED, yellow LED lighting on the side, license plate lighting in LED, 2 white position lights at the front in LED, 2 white/red side marker lights at the rear in LED, 2 x 7-pole and 1 x 15-pole tamper-proof sockets at the front, 2 additional LED work lights at the rear, 1 rotating beacon with holder, switched via parking lights, 2 pairs of warning signs, double LED illuminated and

Condition: new, functionality: fully functional, machine/vehicle number: WFDFLT33801012811, empty load weight: 6,350 kg, maximum load weight: 28,650 kg, overall weight: 35,000 kg, axle configuration: 3 axles, loading space length: 13,650 mm, loading space width: 2,480 mm, total length: 13,850 mm, total width: 2,550 mm, suspension: air, tire size: 435/50 R19,5", tire condition: 100 %, color: silver, available in multiple units Chassis, semi-trailer, forwarding agent: fine-grained steel welded construction, kingpin plate with replaceable 2" kingpin, frame in reinforced design for vehicle loading, outer frame with "Load-Lock profile" approximately every 400 mm for lashing straps, 10 pairs of lashing points recessed in the outer frame at the top/outside, each rated at 10 tons, foldable rear supports, 2 wheel chocks with holder, aluminum side underrun protection, steel underrun protection galvanized, quarter panel fenders in front of the 1st axle and behind each axle, with anti-splash flaps behind each axle, 1 spare wheel holder for 1 wheel, with wheel fastening kit, 2 plastic toolboxes, w=600 / h=425 / d=460 mm, lockable, container locking system, 4 pairs of locking devices recessed in the floor for 2 x 20 ft or 1 x 40 ft containers, the foremost position is a foldable locking device, 10 pairs of stake pockets recessed in the outer frame, internal dimension 70 x 40 mm, 10 stake pockets recessed in the middle of the floor, internal dimension 70 x 40 mm, 2 lashing/stake rails recessed transversely in the floor across the entire width up to the outer frame (max. usable internal width between the outer stake pockets approx. 2170 mm), approx. 100 mm high. With 20 mm round steel strips, top and bottom, distance from top to bottom approx. 60 mm (of the round steel). Bottom with angle plate as a closure, open halfway down. For lashing and inserting stakes 80 x 80 mm. Arrangement: Position 2 and 4 according to Fliegl data sheet, 20 stake pockets, hot-dip galvanized, storage space for aluminum ramps, ramps can be slid in from the rear, 3 pairs of foldable eyelets 10 tons in the outer frame (1 in front of the headboard and 2 in the rear area), Axles + suspension: SAF disc brake axles, air suspension, 1st axle automatic lift axle, including forced lowering and starting aid, operation "3x brake", axle lift below the recommended ride height, therefore no guarantee for tire damage Braking system: 2-line compressed air braking system, color-coded line routing for easy service, spring-loaded parking brake, 2 fail-safe coupling heads at the front, without connecting line, EBS, electronic braking system with EBS socket at the front, without connecting cable, with lifting and lowering valve, 2 ride heights, adjustable via hand control, 1 x for saddle height 980 mm, 1 x for saddle height 1100 mm, ride height in conjunction with lift axle, when the lift axle is raised, the loading or overall height increases by 50 mm, vehicle - driving stability system Wheels and tires: 435/50 R19.5, brand according to manufacturer's choice, steel rims Nodeza Agrspfx Alnscu Electrical system: 24 Volt, multi-chamber lights, yellow LED lighting on the side, 2 white position lights at the front in LED, 2 white/red side marker lights at the rear, 2 x 7-pin and 1 x 15-pin fail-safe sockets at the front, LED work lights on the side, 1 on the left and 1 on the right, 2 additional LED work lights at the rear, 1 rotating beacon with holder, switched via parking lights, 2 pairs of warning signs, LED illuminated and extendable to 4000 mm, additional 7-pin socket in the underrun protection at the rear Floor: Sieve plate, approximately 30 mm thick, on longitudinal girders for high point load capacity for forklift axle load up to a maximum of 7100 kg, Front wall / front corner posts: 25 mm aluminum hollow profile, 1350 mm high, corner posts steel in box profile, front wall additionally covered with 1250 mm h

Condition: new, functionality: fully functional, machine/vehicle number: WFDFLT33802035478, empty load weight: 4,660 kg, maximum load weight: 33,340 kg, overall weight: 38,000 kg, axle configuration: 3 axles, total length: 10,450 mm, total width: 2,550 mm, total height: 1,325 mm, suspension: air, tire size: 385/55 R22.5", tire condition: 100 %, color: grey-black, Chassis, semi-trailer, container Fine-grained steel welded construction, kingpin plate with replaceable 2" kingpin and 2 kingpin positions Front locking on tipper ram mounting with lateral wedge locks, rear locking on continuous pivot shaft with return spring Without subframe for self-supporting containers Container attachments: Locking crossbeam, 2-fold for locking 1 x 30 ft container 24 ton, 2-speed landing gear, single-sided operation, with straight lower part, without push-out compensation Free support leg spacing or free rear swivel radius approx. 1850 mm 2 chock blocks with holder Aluminum side underrun protection Without underrun protection Semi-fender With anti-spray flaps according to EC Ncedpfx Alezaz Tkonou Hydraulics Low-pressure cylinder max. 170 bar, smallest stage hard chrome-plated, with HDK screw fitting, fixed part, NW 48 mm. (without hose connection). Attention! Tilting angle limited! Operation hydraulically via truck auxiliary drive Hydraulic connection with hose and HDK screw fitting NW = 48 mm with knurled nut Axles + Suspension BPW disc brake axles with 430 mm disc diameter "Axle/chassis laser-aligned" Reduces tire wear and fuel consumption Axle spacing offset 1410/1310 mm (combined transport) up to 44 tons total weight Air suspension 1st axle automatic lift axle, including forced lowering and start-up assistance, operation "3x brakes" (start-up assistance is functional up to an axle load exceedance of 30% and up to a speed of max. 25 km/h) Braking system 2-line pneumatic braking system Color-coded line routing for easy maintenance. Spring-loaded parking brake 2 non-interchangeable coupling heads at the front, without connecting line 24 Volt EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The trailer may only be pulled by towing vehicles that guarantee the effectiveness of the ABS! With lifting and lowering valve Vehicle - Driving Stability System Axle load detection via EBS-CAN bus signal, for display on the display in the cab, truck must be prepared accordingly, no truck installation (no calibrated scale) Wheels and Tires 385/55 R22.5" manufacturer's choice Steel rims, factory silver Electrical system 24 Volt, multi-chamber lights, yellow LED lighting on the side 2 white position lights at the front in LED 2 white/red marker lights at the rear 2 x 7-pole non-interchangeable sockets at the front, without connecting cable Country of approval / Signs Germany Type approval according to EC 2007/46 24/7 service hotline Prepared for license plate holder, single row Contour marking with reflective tape according to ECE R 048, white on the side and red at the rear Paint finish Frame DB 7350 Novagrau "10-year warranty against rust" Support legs black coated

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, empty load weight: 7,800 kg, maximum load weight: 27,200 kg, overall weight: 35,000 kg, axle configuration: 3 axles, total length: 13,850 mm, total width: 2,550 mm, total height: 4,020 mm, suspension: air, tire size: 435/50 R19,5", tire condition: 100 %, Based on the tried-and-tested HANGLER welded construction using high-quality steel with forward-tapering welded longitudinal beams. Frame neck with double center web. Z-profile crossbeams punched through the longitudinal beam with welded special side frame. Replaceable 2" kingpin, beveled forward with a grinding plate, made of high-quality steel sheet. 18 pairs of lashing rings embedded in the outer frame, each with a capacity of 2.5 tons, 8 pairs of folding lashing rings embedded in the outer frame, each with a capacity of 5 tons, 24 tons. 2-speed support winch, single-side operation, with straight lower part, 2 support wedges with holder, aluminum side impact protection, plastic fenders in front of and behind each axle, with anti-spray flaps behind each axle, underrun protection at the rear, spray flaps at the rear over the entire width, coil trough approximately 8,000 mm long with cover, approximately 40 mm, divided by angled loading beams. Stanchion sockets and supports suitable for FR 80/80/4, completely hot-dip galvanized. Plug-in stanchions 80/80 including lower reinforcement, hydraulic angled loading device with 4 crossbeams: hydraulic supply via tractor unit using a 2-line pump system (supply and return) with a 2-way quick-release coupling. Angled loading beams with integrated extendable sections that can be locked in height. Hydraulic cylinders multi-stage, each beam with a universal joint suspension. Including supports - adjustable - with pin securing. Cylinder passages with strip brush seals on both sides, to protect against weathering and cleaning of the piston rods. 5-way control block for operating the angled loading device as well as for the folding device. Sliding tarpaulin, including tarpaulin rail cover, 1 set of coil floor holder with height-adjustable support bolts for various coil floor diameters, including storage. 1 piece of impact protection for angled plate - for securing at the front, BPW or SAF disc brake axles, at the manufacturer's choice, offset axle spacing 1310/1450 mm, air suspension, 2-line compressed air brake system, aluminum compressed air tank, spring brake parking brake, axle load recognition via EBS-CAN bus signal, for display on the display in the cab, the truck must be correspondingly pre-equipped, "TPMS" tire pressure monitoring system according to ECE R 141, display via display in the tractor unit, via EBS, 435/50 R 19.5", manufacturer's choice, 24 volts, multi-chamber lights, yellow LED lighting on the side, yellow LED lighting on the side coupled with the turn signal "flashing side marker lights", 2 x 7-pole and 1 x 15-pole fail-safe sockets at the front, additional 7-pole socket (according to ISO 1724) in the underrun protection at the rear, pair of warning signs double LED illuminated and extendable to 3,000 mm, removable with a plug, LED beacon with holder, switched via parking lights, sieve-printed panels approximately 30 mm thick, flush-mounted with the side frame! Front wall made of aluminum hollow profiles, fixed height approximately 2,400 mm, with wooden slats above it. Inside reinforced with 3 mm aluminum sheet, approximately 630 mm high from the floor as a baseboard. 2 front VOLUMEN corner posts, permanently mounted, approximately 2,400 mm high, 3 pairs of Kinnegrip center posts, approximately 600 mm high with Kinnetop at approximately 2,000 mm, 1 pair of plug-in rear corner posts including reinforcement inside up to the 1st slat row, aluminum hollow profile, approximately 600 mm Ncodpfji Riw Hsx Alneu

Condition: good (used), Transformer, converter, three-phase autotransformer, three-phase transformer, three-phase transformer, single-phase transformer -Manufacturer: ismet, transformer Nedpfx Asy Tki Aslnocu -Type: IST 380/220 V -Power: 0.4 kVA -Technical data: see photo of the nameplate -Dimensions: 150/107/H130 mm -Weight: 7.2 kg

Condition: excellent (used), Year of construction: 2022, Atlas Copco FX 300 Refrigeration Dryer Ncodswhwubspfx Alnou Compact, fully automatic, air-cooled compressed air drying system. Flow rate: 18,00 m³/min

Condition: used, Year of construction: 2004, operating hours: 3,623 h, Equipment: all wheel drive, Equipment: * 3,623 operating hours * Deutz engine with 44 kW * 20 KM/H * Bucket * Forks * Additional work lights * Quick coupler * Tires: 12.5-20 Other information: Ncsdpsyn Tt Eefx Alnju * 2 previous owners * German machine * Year of manufacture: 2004 * Total weight: 6,500 kg * Wheel loader, ready for immediate use In November 2009, at approx. 1,300 operating hours, a new tachometer unit was installed. Since 1972, your reliable partner for automobiles and commercial vehicles in 28832 Achim at the Bremer Kreuz. NutzfahrzeugZentrum Behnke always stocks around 200 vehicles from the areas of vans, commercial vehicles, and construction machinery! We continuously offer attractive financing options with special rates. If interested, we are happy to provide you with an individual quote! We welcome trade-ins of your commercial vehicle or construction machinery. If a new TÜV inspection is required, we will gladly provide an offer from our partner workshops. Please note: our offer is generally WITHOUT a new TÜV inspection. Delivery of your "new" commercial vehicle is possible by our external partners for an additional charge. The information provided in listings, online, on price tags, and in images are non-binding descriptions and do not constitute guaranteed properties. The seller assumes no liability/warranty for typing or data transmission errors. Listed equipment must be verified separately if applicable. Subject to errors and prior sale.

Condition: used, Column-guided bandsaw, semi-automatic, METORA - KALTENBACH, type HMB 380 DS for 90° cuts only (Made in Austria) Machine no. 4580028, year of manufacture approx. 1993 Cutting range: round Ø 380 mm Square 380 x 380 mm Saw blade dimensions: 5650 x 34 x 1.1 mm Saw blade speed: 25-108 m/min, infinitely variable Material feed height: 870 mm Hydraulic drive power: 1.5 kW Saw motor drive power: 4 kW Power supply: 400 volts, 50 Hz - Fully hydraulic bandsaw in a two-column design - Hydraulic saw head lowering with infinitely variable cutting pressure adjustment - Lowering speed infinitely adjustable - Hydraulic clamping of the workpiece with hydraulic bundle clamping from above - Hydraulic unit integrated in the machine base - Material feed roller on the feed side with gear motor (not mounted on the machine frame) - Coolant system with coolant pump for water emulsion - Minimum quantity lubrication for the saw blade - Electric heating element for coolant and hydraulics - Length stop, TRENNJAGER type EX-Stop1, with handwheel adjustment, digital display and hydraulic stop carriage clamping Stop base length 6750 mm, stop travel 5650 mm, stop arm can be hydraulically folded up Ncodpjdzqtgefx Alnou without roller conveyor Footprint of the base machine L x W x H: 2800 x 1400 x 2450 mm Machine weight: approx. 3 tons Weight of the stop system: approx. 800 kg in good condition

Operating hours: 38,526 h, condition: used, machine/vehicle number: 23-06757-2, Temperature control unit from the manufacturer Tool-Temp, used and untested. The unit is designed for mold temperature control, injection molding, and process engineering applications. It operates in a single-circuit system with the TT-380 controller. The medium used is oil*, with a maximum supply temperature of 360°C*. Heating capacity is 24 kW*, and pump performance is 90 l/min at 5.5 bar*. The unit is fitted with a K21R 90 S 2 motor. Recorded operating hours are 38,526; year of manufacture is unknown. Nedpey Suavefx Alnocu

Operating hours: 13,241 h, condition: used, machine/vehicle number: 24-02577-4 / TT-380, Temperature control unit by Tool-Temp AG, used and untested. This device is suitable for tool temperature regulation, injection molding, and process engineering applications. Operates with oil and water as heat transfer media in a single-circuit system. Maximum supply temperature is 360°C (oil) or 90°C (water), with a heating capacity of 24 kW. The pump delivers up to 90 l/min at 6.0 bar; the control system is MP-888. Operating hours are specified at 13,241, year of manufacture unknown. Accessories include a digital hour meter, analog pressure gauge, transport castors, and crane lugs for loading. Ncjdpfey St Ursx Alnju

Condition: good (used), mileage: 309,720 km, power: 206 kW (280.08 HP), first registration: 03/2011, fuel type: diesel, axle configuration: 6x2, fuel: diesel, color: white, gearing type: automatic, number of gears: 8, emission class: euro5, permissible axle load (axle 1): 9,000 kg, permissible axle load (axle 2): 11,500 kg, permissible axle load (axle 3): 7,500 kg, Year of construction: 2011, Equipment: ABS, air conditioning, crane, cruise control, differential lock, electric window regulation, power assisted steering, trailer coupling, = Additional Options and Equipment = - Aluminum fuel tank - Passenger seat - Roof hatch - Differential lock - Euro 5 - Height-adjustable steering wheel - Air suspension - Disc brakes - Sun visor - Converter - Power Take-Off (PTO) - Partition wall with window = Further Information = Nodpfx Ajx Trt Nslnocu Axle Configuration Front axle: Max. axle load: 9,000 kg; Steered Rear axle 1: Twin tires; Differential lock; Max. axle load: 11,500 kg Rear axle 2: Max. axle load: 7,500 kg; Steered Weights Unladen weight: 17,095 kg Payload: 10,905 kg Gross vehicle weight (GVW): 28,000 kg Functional Mast: Slider Crane: HIAB, year of manufacture 2005, mounted at rear of chassis Body brand: FASSI F455A.2.25 Condition Technical condition: good Optical condition: good Identification Registration number: BZ-BX-43

Condition: used, Year of construction: 2013, functionality: fully functional, operating hours: 515 h, input voltage: 400 V, input current: 74 A, input frequency: 50 Hz, type of input current: three-phase, travel distance X-axis: 5,020 mm, travel distance Y-axis: 1,380 mm, workpiece width (max.): 1,300 mm, workpiece height (max.): 450 mm, workpiece weight (max.): 7,250 kg, number of axes: 4, number of slots in tool magazine: 36, controller manufacturer: SCM, actuation type: electric, total height: 3,000 mm, total length: 9,778 mm, total width: 6,158 mm, overall weight: 7,250 kg, table length: 5,680 mm, table width: 1,300 mm, Equipment: CE marking, documentation/manual, We offer a four-axis machining center, the SCM ACCORD 30 FX. The machine is configured for the production of window and door joinery. It features an additional BRC unit and is equipped with two tool magazines and a good vacuum pump. The machine has been used very little and is practically a new unit, which we can confirm through the SCM Group, from which it was purchased as new. It is possible to obtain a certificate and warranty from the manufacturer, SCM. Brand: SCM Type: Accord 30 FX Model: ACCORD 30 FX Serial number: AA2/002707 Year of manufacture: 2013 Weight: 7250 kg Ncodpsy Udznsfx Alnju If you have any questions or require further information, please send us a message or contact us by phone.