Used Cantilever Rack Shelf for sale (4,290)

Year of construction: 2020, condition: used, FISCHER – Cantilever racking for installation in enclosed spaces. The racking must not be clad on-site without consulting FISCHER. Design according to the specifications. Racking No. 1 - single-sided (cantilever arms bolted on). Number of racks: The following information refers to 1 rack. 1 unit Number of uprights: 3 units Racking length (center-to-center distance): 2,500 mm Distance between uprights: 2 x 1,250 mm Upright height (hole pitch 100 mm): approx. 2,500 mm Top storage level: 2,200 mm Foot length: 1st side/2nd side 2,000 / 0 mm Cantilever arm lengths (total length incl. end stop): 2,000 mm Cantilever arms: 1st side/2nd side 4 / 0 units Hsdpfx Ajzab Rcecdon Desired load capacity per cantilever arm: 500 kg Load capacity per upright side (without considering the foot): 2,000 kg Max. floor pressure: 0.11 kN/cm2 Shipping weight per rack: 607 kg Color of uprights: fire red, similar to RAL 3000 Color of cantilever arms: fire red, similar to RAL 3000 1 spray can The profile thickness applies to 100% utilization of the rack load capacity. Seismic zone could not be determined. A verifiable or tested static analysis is available for an additional charge. Text for the static calculation: Important note regarding the static calculation of the storage system: The static calculations take into account the fundamentals according to Eurocode (DIN EN 1991-1-1, DIN EN 1991-3 and DIN EN 1991-1-4) and the framework conditions of the respective national annexes (NA) applicable in the countries where the system will be installed. Since storage systems are usually installed in urban or industrial areas, the requirements applicable to these areas (e.g., for Germany, ground category III and IV) are included in the calculation. Important note regarding building permits, please note: Storage systems may require a permit according to the respective state building code. In the event of an order placed with Fischer, the client undertakes to obtain the necessary public-law permits for the storage system. If the permit is not granted, or the granted permit is revoked or withdrawn, the contractor shall not be liable for this. In the event of installation by Fischer, we generally assume that a valid building permit is in place at the time of installation. Any necessary verifiable static calculations for the building application can be obtained for a fee; please contact us. Cantilever racking: 1 unit 1,500.00 Foot rounding as a safety element: 3 units 13.50 per foot and side Storage location: Customer

Condition: good (used), Pallet racking, heavy-duty racking, high-bay racking, boltless racking, warehouse racking uprights, individual uprights, bracing profiles, shelf panels, shelves, shelf boards -Storage rack: Steel uprights and wooden shelves in various sizes -Shelf stands: Dimensions 1990 x 500 mm (10 Euro net) 1 pc. / 2992 x 500 mm 5 pcs. (12 Euro net) Hjdpfor U Sgwjx Acdon -Shelf units: 1000 x 500 mm 194 pcs (5 Euro net) / 1000 x 600 mm 168 pcs (6 Euro net) -Weight: Stands 5.4 to 8.4 kg/pc. / Shelves 5.6/6.3 kg/pc.

Condition: new, Year of construction: 2020, Cantilever rack NEW PRODUCT Data: - H: approx. 416 cm - D: approx. 137 cm - L: approx. 402 cm - Cantilever arms: approx. 120 cm - Axle dimension: 131 cm - NEW PRODUCT immediately from stock. - 750 kg load per arm - 2250 kg load per stand - Stand in hot-dip galvanized. - Cantilever arms in hot-dip galvanized. Hodszac Ezspfx Acdjn - Arms are screwed. - Arms adjustable in 100 mm increments. - Levels: base + 3 storage levels (4 storage levels) Shelf consists of: - 04 x stands, including base approx. 416 cm made of IPE160. - 12 x cantilever arms approx. 120 cm made of IPE 100 - including all necessary connecting elements and screws. Why BLT cantilever racks? - Certified German manufacturer DIN EN 1090 - Made in Germany - All specified load-bearing capacities of the shelf uprights and cantilevers are statically verifiable, at 100% load. - All shelving systems are supplied in hot-dip galvanized versions. They can therefore be set up inside and outside and do not rust like painted systems. Consistent appearance for many years. - We use the legally required hot-dip galvanized screw sets in accordance with DIN EN 15048-1 - Long availability guarantee - The stand base and stand back are welded together, which provides additional safety and short assembly times because the feet do not have to be screwed to the stand back. - Angle steel braces, so no adjustment using turnbuckles is necessary. This shortens the assembly time. - No slotted hole system, so no weakening of the stand profile. Price: €2631.00 net + legally applicable VAT. You will receive an invoice with VAT shown. Accessories such as ground anchors, collision protection, etc. can also be purchased from us. Our recommendation: Tell us what you need... We will be happy to help you realize your projects, from planning to ordering to installation. Delivery is possible on request at a reasonable price.

Condition: as good as new (ex-display), functionality: fully functional, This single-sided heavy-duty cantilever rack is ideal for storing heavy long goods such as pipes, profiles, metal bars, steel beams, wooden strips, and sheet material. With a total length of approximately 13.20 meters, a height of approximately 4.00 meters, and cantilever arms of approximately 120 cm, this long goods rack offers a high storage capacity across a total of 4 storage levels (floor level + 3 levels). Each cantilever arm supports up to 500 kg, and the uprights can support up to 2,250 kg. The cantilever arms are bolted on and can be flexibly adjusted in height via a hole grid of 200 mm. The completely hot-dip galvanized material ensures long-lasting protection both indoors and outdoors – new goods available from the Wietmarschen warehouse. PRODUCT DETAILS: - Rack type: single-sided heavy-duty cantilever rack - Total length of the rack row: approx. 13.20 m - Total height: approx. 400 cm - Arm length: approx. 120 cm (made of IPE 80) - Center distance (upright spacing): approx. 131 cm - Levels: floor level + 3 storage levels - Load capacity per arm: max. 500 kg (with uniform distribution) - Load capacity per upright: max. 2,250 kg (with uniform distribution) - Upright profile: IPE 160, approx. 400 cm, including base - Hole grid upright: approx. 20 cm - First hole above base: approx. 107.5 cm (from top of base) - Top hole pair: approx. 50 cm below the upright head (from top of head) - Design: single-sided, cantilever arms bolted on - Surface: completely hot-dip galvanized - Availability: new goods SCOPE OF DELIVERY: - 11 x uprights, approx. 400 cm made of IPE 160, including base, hole grid 20 cm - 33 x cantilever arms, approx. 120 cm made of IPE 80 (without end stops) - Including all connecting elements - Including all necessary screws - 1 x load sign Price: €5,750.00 net €6,842.50 gross You will receive an invoice with VAT shown. Hjdpfx Ajy U Uh Ejcden DELIVERY, ASSEMBLY & INSPECTION: - Nationwide delivery by our partner shipping company – freight costs depend on the postal code - Professional assembly and disassembly by trained teams is optionally available - Rack inspections according to DIN EN 15635 by certified inspectors - Inspection of existing heavy-duty racks from other manufacturers is also possible PLANNING & CONSULTATION: Our planning department will be happy to prepare a non-binding offer for you – tailored to your individual requirements. Whether it's a new installation, renovation, or expansion – we will provide you with competent advice on your rack configuration. Haven't found the right one yet? Visit our website – here you will find a quick overview of many offers and variations of the products! ARE YOU INTERESTED OR DO YOU HAVE QUESTIONS? Simply contact us via message or phone call. You will find our telephone number on our company website. You can reach us by telephone from Monday to Friday, 08:00 - 16:00. Alternatively, you can send us a message with your name and number, and we will get back to you as soon as possible.

Year of construction: 2021, condition: new, Cantilever rack, one-sided, 3.70m height, 1.20m arms, 500kg per arm - new -: Price ex location including loading! 1 shelf unit with 4 stands € 2.255 (net)! Price for transport within Germany (excluding islands): € 490 (net)! Of course, you can also build longer or shorter shelving units from them by omitting or buying additional frames (or by using different center distances), this example with 4 frames is only the most common shelving solution! A cantilever racking system, hot-dip galvanized, consisting of: Arms: IPE 80 Frame: IPE 180 Shelf stand on one side approx. 3,700mm high, hot-dip galvanized Leg and arm depth 1200 mm with 3 height-adjustable shelf arms each Load capacity at a load center of 600 mm 500 kg per arm / 2,700 kg per stand with 4 stands per arm level 4 x 500 kg = 2,000 kg with longitudinal and diagonal bracing e = 1300 mm, the standard is 1.30 m - so if you do not have any deviating information, we will deliver the rack with a center distance of 1.30 m. Other center distances possible e.g. 1m, 1.25m for a small surcharge also 1.50m or special dimensions! As a standard delivery, the length of a row of shelves with 4 uprights is approx. 4000 mm. Delivery with all screws and nuts, without ground anchors. Hsdpfx Acjf Tv T Nodsn Other configurations (frame height, arm lengths, arm types etc.) can be selected! Please contact us!

Year of construction: 2021, condition: new, Cantilever rack, one-sided, 2.60m height, 1m arms, 600kg per arm, hot-dip galvanized - new -: Price: € 1,485,- (net) transport within Germany (excluding islands)!430,-€(netto) Of course, you can also build longer or shorter shelving units from them by omitting or buying additional frames (or by using different center distances), this example with 4 frames is only the most common shelving solution! A cantilever racking system, hot-dip galvanized, consisting of: German brand manufacturer, new goods Description: - Shelf uprights on one side 2,600 mm high, hot-dip galvanized - Foot and arm depth 1000 mm Hodpfod Epfvjx Acdsn - each with 3 height-adjustable shelf arms - Load capacity at a load center of 500 mm - 600 kg per arm / 1,800 kg per stand with 4 stands per arm level 4 x 600 kg = 2,400 kg Profiles: Frame (stand): IPE 140, arms IPE 80 with longitudinal and diagonal bracing e = 1300 mm, the standard is 1.30 m - if you do not have any deviating information, we will deliver the rack with a center distance of 1.30 m. Other center distances possible e.g. 1m, 1.25m for a small surcharge also 1.50m or special dimensions! As a standard delivery, the length of a row of shelves with 4 uprights is approx. 4000 mm. Delivery with all screws and nuts, without ground anchors. Other configurations (frame height, arm lengths, arm types etc.) can be selected! Please contact us!

Year of construction: 2021, condition: new, Cantilever rack, one-sided, 3m height, 1.20m arms, 500kg per arm - new -: Price ex location including loading! Hedpfx Acjddmpvsdsn 1 shelf unit with 4 stands 1.833.- € (net)! Price for transport within Germany (excluding islands): € 500 (net)! Of course, you can also build longer or shorter shelving units from them by omitting or buying additional frames (or by using different center distances), this example with 4 frames is only the most common shelving solution! A cantilever racking system, hot-dip galvanized, consisting of: Shelf uprights on one side approx. 3,000 mm high, hot-dip galvanized, IPE 160 Leg and arm depth 1200 mm with 3 height-adjustable shelf arms each Load capacity at a load center of 600mm 500 kg per arm / 2250 kg per stand with 4 uprights per arm level 4 x 500 kg = 2,000 kg, arms IPE 80, with longitudinal and diagonal bracing e = 1300 mm, the standard is 1.30 m - so if you do not have any deviating information, we will deliver the rack with a center distance of 1.30 m. Other center distances possible e.g. 1m, 1.25m for a small surcharge also 1.50m or special dimensions! As a standard delivery, the length of a row of shelves with 4 uprights is approx. 4000 mm. Delivery with all screws and nuts, without ground anchors. Other configurations (frame height, arm lengths, arm types etc.) can be selected! Please contact us!

Condition: new, Cantilever rack, one-sided, frame height 2.60m high, 80cm deep arms, 750kg per arm, hot-dip galvanized - New - : Price ex site incl. loading! Price: 1.480.-€ (net) Price transport / packaging costs within Germany (without islands): 400.-€ (net)! Of course, you can also build longer or shorter shelving units by omitting or purchasing additional frames (or by using different center distances), this example with 4 frames is only the most common shelving solution! A cantilever racking system, hot-dip galvanized, consisting of: German brand manufacturer, new goods Description: - Shelving upright, one-sided 2,600 mm high, hot-dip galvanized - Base and arm depth 800 mm - with 3 height-adjustable shelf arms each - Load capacity with load center 400 mm - 750 kg per arm / 2..250 kg per upright with 4 uprights per arm level 4 x 750 kg = 3,000 kg Profiles: Frame (uprights): IPE 140, arms IPE 80 Hsdsnwmwvjpfx Acdsn incl. longitudinal and diagonal bracing, The standard center distance between the frames is 1.30 m. Other standard center distances available from stock: 1m / 1.25m / 1.50m / 1.70m / 1.90m! From a length of 1.50m there is a small surcharge on top of the stated price! Special dimensions (other center distances) are also available on request, but also cost extra and have a longer delivery time as they have to be made separately! If you do not specify a different center distance, we will deliver the shelf with a center distance of 1.30m. In this case, the length of a row of shelves with 4 uprights (3 bays) is approx. 4m. Supplied with all screws and nuts (dispatch within Germany by parcel directly from Würth), without ground anchors. When using additional arms per frame, please note that the specified maximum load capacity of the frames must not be exceeded, or the maximum usable load capacity per arm will be reduced! Other configurations (frame height, arm lengths, arm types etc.) can be selected! Please contact us! Available optional extras (at extra cost), photos enclosed: Footrest with load deflector Footrest with load deflector, large Foot section with tire guard Cantilever arm with load deflector Cantilever arm with plug-in roll-off protection Clampable roll-off protection Gratings Conversion for use for the storage of pallets Photos are examples of single-sided shelving and the material used!

Condition: new, Year of construction: 2020, Cantilever rack, one-sided, 6.30m high, 1.20m arms, 900kg per arm - new - : Price ex location incl. loading! 1 shelving unit with 4 uprights 3.732.-€ (net)! Transportation costs within Germany (without islands): 490.-€ (net)! One cantilever shelving system, hot-dip galvanized, consisting of: Shelving upright, one-sided approx. 6,300 mm high, hot-dip galvanized Base and arm depth 1200 mm with 3 height-adjustable shelf arms each Load capacity with load center 600 mm 900 kg per arm / 4,000 kg per upright with 4 uprights per arm level 4 x 900 kg = 3,600 kg Profiles: Frame: IPE220, arms: IPE 100 with longitudinal and diagonal bracing e = 1300mm, standard is 1.30m. Other standard lengths available from stock: 1m / 1.25m / 1.50m / 1.70m / 1.90m! From a length of 1.50m there is a small surcharge on top of the stated price! Special dimensions (other center distances) are also available on request, but also cost extra and have a longer delivery time as they have to be made separately! If you do not specify a different center distance, we will deliver the shelf with a center distance of 1.30m. In this case, the length of a row of shelves with 4 uprights (3 bays) is approx. 4m. Supplied with all nuts and bolts (dispatch within Germany by parcel direct from Würth), without ground anchors. Hsdpfxjfivg Ss Acdjn Other configurations (frame height, arm lengths, arm types etc.) available! Please contact us!

Year of construction: 2021, condition: new, Cantilever rack, one-sided, 6.30m height, 1.20m arms, 500kg per arm - new -: Price ex location including loading! 1 shelf unit with 4 stands € 4.115 (net)! Hjdsfivg Rspfx Acdjn Transport costs within Germany (excluding islands): € 490 (net)! Of course, you can also build longer or shorter shelving units from them by omitting or buying additional frames (or by using different center distances), this example with 4 frames is only the most common shelving solution! A cantilever racking system, hot-dip galvanized, consisting of: Shelf uprights on one side approx. 6,300 mm high, hot-dip galvanized Leg and arm depth 1200 mm with 3 height-adjustable shelf arms each Load capacity with a load center of 600 mm 500 kg per arm / 4,000 kg per stand with 4 stands per arm level 4 x 500kg = 2,000 kg Profiles: frame: IPE220, arms: IPE 80 with longitudinal and diagonal bracing e = 1300 mm, the standard is 1.30 m - so if you do not have any deviating information, we will deliver the rack with a center distance of 1.30 m. Other center distances possible e.g. 1m, 1.25m for a small surcharge also 1.50m or special dimensions! As a standard delivery, the length of a row of shelves with 4 uprights is approx. 4000 mm. Delivery with all screws and nuts, without ground anchors. Other configurations (frame height, arm lengths, arm types etc.) can be selected! Please contact us!

Year of construction: 2021, condition: new, Cantilever rack, double-sided, 4.16m height, 1.20m arms, 750kg per arm - NEW -: Price ex location including loading! 1 shelf unit with 4 stands 3420,- € (net)! Price for transport within Germany (excluding islands): € 550 (net)! Of course, you can also build longer or shorter shelving units from them by omitting or buying additional frames (or by using different center distances), this example with 4 frames is only the most common shelving solution! A cantilever racking system, hot-dip galvanized, consisting of: 4 shelf stands, double-sided, approx. 4.16 m high, hot-dip galvanized IPE 160/100 each with 2x3 adjustable. Arms 1.20 m, 750kg load capacity per arm Hjdpofivhfofx Acden with bandages approx. 1.30 m Shelf uprights on both sides approx. 4160mm high, hot-dip galvanized Leg and arm depth 1200 mm with 3 height-adjustable shelf arms each Load capacity at load center of 600 mm 750kg per arm / 2250kg per stand side with longitudinal and diagonal bracing e = 1300 mm, the standard is 1.30 m - so if you do not have any deviating information, we will deliver the rack with a center distance of 1.30 m. Other center distances possible e.g. 1m, 1.25m for a small surcharge also 1.50m or special dimensions! As a standard delivery, the length of a row of shelves with 4 uprights is approx. 4000 mm. Delivery with all screws and nuts, without ground anchors. Other configurations (frame height, arm lengths, arm types etc.) can be selected! Please contact us!

Condition: new, Year of construction: 2025, Cantilever racking for light loads, single-sided, frame height 2m, rack length approx. 3m, arms 50cm deep, 200kg per arm, hot-dip galvanized – new product: Price ex-works including loading: only €895 (net), plus packaging and freight. Price per additional upright: €225 (net) Transport cost on request! Hodpfx Aexbz Ddocden Manufacturer: Bruckamp Year of manufacture: New Model: Super Light Set components: 4 uprights with 5 arms / 3 bays with connectors Upright spacing: approx. 1m Total assembled length: approx. 3m Rack height: 2m Base and arm depth: 500mm Robust construction – made from IPE 100 with welded arms at approx. 330mm intervals. Load capacity per upright: 1,000kg Load capacity per arm: 200kg Includes floor anchors Includes load rating plate Description: Set of 4 uprights with 1m bay width, including all bolts. Key advantages: Easy assembly – the rack is designed for quick and straightforward installation. Versatile use – whether in the garage, workshop, or for small spaces, the rack adapts flexibly. Safe & practical – the rectangular arms feature plastic end caps to prevent injuries.

Year of construction: 2020, condition: new, Cantilever rack, double-sided, 3.50m height, 1.20m arms, 750kg per arm - NEW -: Hedpefivhgefx Acdon Price ex location including loading! 1 shelf unit with 4 stands € 3.210,- (net)! Price for transport within Germany (excluding islands): € 550 (net)! Of course, you can also build longer or shorter shelving units from them by omitting or buying additional frames (or by using different center distances), this example with 4 frames is only the most common shelving solution! A cantilever racking system, hot-dip galvanized, consisting of: 4 shelf stands, double-sided, approx. 3.50 m high, hot-dip galvanized IPE 160/100 each with 2x3 adjustable. Arms 1.20 m, 750kg load capacity per arm with bandages approx. 1.30 m Shelf uprights on both sides approx. 3500mm high, hot-dip galvanized Leg and arm depth 1200 mm with 3 height-adjustable shelf arms each Load capacity with load center of 600 mm 750 kg per arm / 2250 kg per stand side with longitudinal and diagonal bracing e = 1300 mm, the standard is 1.30 m - so if you do not have any deviating information, we will deliver the rack with a center distance of 1.30 m. Other center distances possible e.g. 1m, 1.25m for a small surcharge also 1.50m or special dimensions! As a standard delivery, the length of a row of shelves with 4 uprights is approx. 4000 mm. Delivery with all screws and nuts, without ground anchors. Other configurations (frame height, arm lengths, arm types etc.) can be selected! Please contact us!

Condition: new, Year of construction: 2026, Approx. 360 starter bays (more available on request), boltless shelving racks, plug-in system, manufacturer: dalminels, dimensions: 1.30m x 0.60m (other sizes available), frame height: 2.20m (other heights available) – New equipment: Price per starter bay: €119 (net) Price per extension bay: €99 (net) Purchase only by the truckload, otherwise the transport costs may be disproportionately high! Approx. 360 bays fit per truckload (depending on configuration). Manufacturer: dalminels, Italy Model: Errex Year of manufacture: New Finish: Galvanized Frame height: approx. 2.20m (other heights, e.g., 2m available on request) Load capacity per level: 141 kg 5 shelves per bay – additional shelves available at extra cost Shelves approx. 1.30m x 0.60m (shelves consist of 3 panels, each 20cm deep) This system features shelves that slot into rails on the sides. Hodpfxjyhxmne Acdon Condition: New delivery time: approx. 4 weeks, usually faster – please inquire for current lead times! Location: Delivery included within Germany Other shelf sizes available on request: For example: Widths: 1m and 1.30m Depths: 30cm / 40cm / 50cm / 60cm / 70cm / 80cm Accessories available at extra cost: e.g., drawers, dividers, bracing beams as an alternative to cross braces, etc. Also available as multi-level installations!

Condition: good (used), Year of construction: 2019, Racking Hall consisting of cantilever and pallet racks, OHRA, floor area approx. 867m² – used –: Price ex location: €99,500 (net), for self-dismantling! Price for dismantling available on request. Material to close one gable side is also available at extra cost! Manufacturer: OHRA Year of manufacture: 2019, sheet metal 2021 Hall dimensions: Width: approx. 17.35m Length: approx. 50m Height rack: approx. 6,385mm Ridge height: approx. 7.10m After disassembly, one long side of the hall remains open (where it currently adjoins the existing building) Cantilever racking: 2 rows of 25 double-sided frames each = total 50 double-sided cantilever rack frames Arm length: 1.20m Arm load: 1,400kg Load center: 600mm Post load per side: 4,200kg Axle spacing: 2m Arms are plugged in Arms have load deflectors, preparation for unrolling protection Incl. pallet beams Base level plus 3 arm levels per side Total depth: 2.70m (2 x 1.20m plus 30cm frame) Aisle width: 3.25m K-Foot-60-IPE 300-1200-1200-RS-A-RAL K-Roof arm-K60-IPE 120-2750-S6°-PW4-A-RAL Pallet racking: Manufacturer: OHRA System: pallet racking P3 Year: 2019 Bay width: 2,900mm, four bays at length 2.40m Bay load: 2,000kg Field load: 6,000kg Top edge 1st support (buckling length): 800mm 1 row with 17 frames, 1 row with 19 frames (there are pipes at two locations) Number of frames: 36 Rack length: approx. 48.10m Frame depth: 1.10m Frame width: approx. 10cm Beam height: approx. 10cm Beam thickness (bearing surface): approx. 5.5cm Beams: IPE Floor plus 3 beam levels Number of beams: approx. 162 pcs at 2.90m and approx. 24 pcs at 2.40m length Snow load zone: 1 (0.65kN/m²) Wind zone: 1 / Terrain category 0.48kN/m² Available: immediately Condition: good, slight rust on outer frames and faded paint Location: Hockenheim region Hodpfx Asyk H Riscden Drawing available as PDF, parts list, structural calculations. The sideloader shown in the photos is also for sale at extra cost (it recently received a nearly new battery for approx. €9,600 net).

Condition: used, Colour: Grey Empty weight: 14.400 kg Length: 552 cm Price: On request - Details: - └ Description: Disassembled - Documentation available: No - CE certificate present: No - Type of rack: Single - Number of uprights [pcs]: 96 Hjdpfx Acey Ta Hdsdsn - Number of beams [pcs]: 384 - Total load capacity per upright [kg]: 3000 - Load capacity per arm [kg]: 1000 - Arm length [mm]: 1220 - Upright height [mm]: 5520 - Foot length [mm]: 1220 - Width between uprights [mm]: 1500 - Transport weight [kg]: 14400kg Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Tess van den Boom

Condition: used, Various cantilever racks 4x rack: Dimensions: 6,125 x 2,400 x 3,000 mm Weight approx.: 8,000 kg Hsdpfsyrq Nljx Acdjn 2x rack: Dimensions: 5,650 x 2,400 x 3,000 mm Weight approx.: 7,380 kg Static calculations available !! Image 1 shows the rack in its assembled state !! ä19526

Condition: new, 250 Shelf racks Stacking racks Transport racks New, very good condition, see pictures Dimensions: 1545 x 1185 x 310 mm Hot-dip galvanized Stackable max. load 2000kg Own weight 34kg (base frame without tubes) Negotiated price: € 159,-- net ex stock Base frame without tubes: € 159,-- net ex stock Base frame incl. tubes 100cm: € 227,-- net from stock Base frame incl. tubes 150cm: € 255,-- net from stock Base frame incl. tubes 200cm: € 275,-- net from stock Goods are in stock. Transportation and assembly possible on request. Viewing possible at any time by appointment. Further information on request. Hedpjuq Eurjfx Acdon Over 5000 running meters of pallet racking from numerous manufacturers in stock.

Condition: new, Cantilever rack, new H: 400cm, base +3 storage levels with roof & rear panel Free delivery within Germany, except islands Data : - H : approx. 400 cm - D : approx. 147 cm - L : approx. 1420 cm - Cantilever arms : approx. 125 cm - Axial dimension: 290 cm (can be adapted to customer requirements) - New goods - made in Germany. - Delivery time approx. 6 weeks after commercial clarification. - 1000 kg load per arm - 4000 kg load per upright - Uprights in hot-dip galvanized. - Cantilever arms in hot-dip galvanized. - Arms are bolted. - Arms adjustable in 200 mm increments. - Levels: Base + 3 storage levels (4 storage levels) Shelf consists of : - 06 x uprights, incl. base approx. 400 cm made of IPE270. - 18 x cantilever arms approx. 125 cm made of IPE 120. - 06 x roof girder approx. 150 cm made of IPE 120, 5° rising roof pitch. - incl. roof and rear wall material. - incl. all necessary connecting elements and screws. Why BLT cantilever racks ? - Certified German manufacturer DIN EN 1090 - Made in Germany - All specified load-bearing capacities of the uprights and cantilever arms are statically verifiable at 100% load. - All shelving systems are supplied in a hot-dip galvanized version. They can therefore be installed both indoors and outdoors and do not rust like painted systems. Consistent appearance for many years. - We use the legally prescribed hot-dip galvanized screw fittings in accordance with DIN EN 15048-1 - Long after-sales guarantee - The upright base and upright back are welded together, providing additional safety and short assembly times because the feet do not have to be bolted to the upright back. - Bracing made of angle steel, so no adjustment with turnbuckles necessary. This shortens the assembly time. - No slotted hole system, therefore no weakening of the upright profile. Price : 12.250,00 € net plus statutory value added tax. You will receive an invoice with VAT shown. Assembly : If required, our trained staff will be happy to assist you with the professional assembly and disassembly of your operating equipment. Our recommendation : Let us know what you need... We will be happy to help you with the realization of your projects, from planning and ordering to installation. Hsdjy Uh Sqspfx Acdjn

Condition: new, Year of construction: 2022, Cantilever rack NEW PRODUCT Data: - H: approx. 350 cm - D: approx. 137 cm - L: approx. 402 cm - Cantilever arms: approx. 120 cm - Axle dimension: 131 cm - NEW PRODUCT immediately from stock. - 500 kg load per arm - 2250 kg load per stand - Stand in hot-dip galvanized. - Cantilever arms in hot-dip galvanized. - Arms are screwed. - Arms adjustable in 100 mm increments. - Levels: base + 3 storage levels (4 storage levels) Shelf consists of: - 04 x stands, including base approx. 350 cm made of IPE160. - 12 x cantilever arms approx. 120 cm made of IPE 80 - including all necessary connecting elements and screws. Why BLT cantilever racks? - Certified German manufacturer DIN EN 1090 - Made in Germany - All specified load-bearing capacities of the shelf uprights and cantilevers are statically verifiable, at 100% load. - All shelving systems are supplied in hot-dip galvanized versions. They can therefore be set up inside and outside and do not rust like painted systems. Consistent appearance for many years. - We use the legally required hot-dip galvanized screw sets in accordance with DIN EN 15048-1 - Long availability guarantee - The stand base and stand back are welded together, which provides additional safety and short assembly times because the feet do not have to be screwed to the stand back. - Angle steel braces, so no adjustment using turnbuckles is necessary. This shortens the assembly time. - No slotted hole system, so no weakening of the stand profile. Price: €2356.00 net + legally applicable VAT. You will receive an invoice with VAT shown. Hodpfx Ajy Uh Sdecdjn Transport: Delivery is carried out by our partner shipping company on request, the costs for this depend on the postcode. Assembly: If required, our trained staff will be happy to assist you with the professional assembly and disassembly of your business equipment. Our recommendation: Let us know what you need... We will be happy to help you with the realization of your projects, from planning to ordering to assembly.

Condition: new, Cantilever shelf, double-sided, new goods Data: - H: approx. 400 cm - W: approx. 256 cm - L: approx. 18.45 linear meters - Cantilever arms: approx. 120 cm - Axle dimension: approx. 131 cm - New goods from the factory - Double-sided - 500 kg load per arm - 2250 kg load per stand - Stands in hot-dip galvanized. - Cantilever arms in hot-dip galvanized. - Arms are screwed. Hodpfx Asy Uh R Tecdsn - Arms adjustable in 200 mm increments. - Levels: base + 4 storage levels (5 storage levels) - Delivery time approx. 4 weeks Shelf consists of: - 015 x stands, double-sided, including base approx. 400cm made of IPE160. - 120 x cantilever arms approx. 120 cm made of IPE 80, without deflectors - including all necessary connecting elements and screws. Why BLT cantilever racks? - Certified German manufacturer DIN EN 1090 - Made in Germany - All specified load capacities of the shelf uprights and cantilever arms can be statically verified, at 100% load. - All shelving systems are supplied in hot-dip galvanized versions. They can therefore be set up inside and outside and do not rust like painted systems. Consistent appearance for many years. - We use the legally required hot-dip galvanized screw sets in accordance with DIN EN 15048-1 - Long availability guarantee - The stand base and stand back are welded together, which provides additional safety and short assembly times because the feet do not have to be screwed to the stand back. - Brackets made of angle steel, so no adjustment using turnbuckles is necessary. This shortens the assembly time. - No slotted hole system, so no weakening of the stand profile. Price: €12,450.00 net plus statutory VAT. You will receive an invoice with VAT shown. Transport: Delivery is carried out by our partner shipping company on request, the costs for this depend on the postcode. Assembly: Our trained staff will be happy to assist you with the professional assembly and disassembly of your business equipment if required. Our recommendation: Let us know what you need... We will be happy to help you with the realization of your projects, from planning to ordering to assembly.

Condition: new, Cantilever racking to your desired dimensions! Ideal for storing your long goods. Easy access to your products thanks to configurations that can be used on one or both sides. Expandable system that allows you to add elements as your requirements evolve. Perfect for offcuts or long goods in metal and wood businesses. Why BLT cantilever racking? - Certified German manufacturer DIN EN 1090 - Made in Germany- - All specified load-bearing capacities of the uprights and cantilever arms are statically verifiable at 100% load! - All shelving systems are supplied in a hot-dip galvanized version. They can therefore be installed both indoors and outdoors and do not rust like painted systems. Consistent appearance for many years. - We use the legally prescribed hot-dip galvanized screw fittings in accordance with DIN EN 15048-1 - We use the legally prescribed C4 load plates in accordance with DIN EN 15635 / BGR 234 - Long after-sales guarantee - The upright base and upright back are welded together, providing additional safety and short assembly times because the feet do not have to be bolted to the upright back. - Bracing made of angle steel, so no adjustment with turnbuckles necessary. This shortens the assembly time. - No slotted hole system, so no weakening of the upright profile. Transportation : On request, delivery is carried out by our partner forwarding company, the costs for this depend on the zip code. Assembly : If required, our trained staff will be happy to assist you with the professional assembly and disassembly of your factory equipment. Our recommendation : Let us know what you need... Hedpfxjy Uh R He Acdsn We will be happy to help you with the realization of your projects, from planning and ordering to installation. Are you interested or do you have any questions? Simply contact us by message or phone call. You can find our telephone number on our company page. ☎️ You can reach us by phone from Monday to Friday, 08:00 - 15:00. Alternatively, you can send us a message with your name and number and we will get back to you as soon as possible.

Condition: new, Year of construction: 2020, Cantilever rack NEW PRODUCT Data: - H: approx. 300 cm - D: approx. 137 cm - L: approx. 402 cm - Cantilever arms: approx. 120 cm Hedpfjy Uh Rtox Acdon - Axle dimension: 131 cm - NEW PRODUCT immediately from stock. - 750 kg load per arm - 2250 kg load per stand - Stands in hot-dip galvanized. - Cantilever arms in hot-dip galvanized. - Arms are screwed. - Arms adjustable in 100 mm increments. - Levels: base + 3 storage levels (4 storage levels) Shelf consists of: - 04 x stands, including base approx. 300 cm made of IPE160. - 12 x cantilever arms approx. 120 cm made of IPE 100 - including all necessary connecting elements and screws. Why BLT cantilever racks? - Certified German manufacturer DIN EN 1090 - Made in Germany - All specified load-bearing capacities of the shelf uprights and cantilevers are statically verifiable, at 100% load. - All shelving systems are supplied in hot-dip galvanized versions. They can therefore be set up inside and outside and do not rust like painted systems. Consistent appearance for many years. - We use the legally required hot-dip galvanized screw sets in accordance with DIN EN 15048-1 - Long availability guarantee - The stand base and stand back are welded together, which provides additional safety and short assembly times because the feet do not have to be screwed to the stand back. - Angle steel braces, so no adjustment using turnbuckles is necessary. This shortens the assembly time. - No slotted hole system, so no weakening of the stand profile. Price: €2404.00 net + legally applicable VAT. You will receive an invoice with VAT shown. Accessories such as ground anchors, collision protection, etc. can also be purchased from us. Transport: Delivery is carried out by our partner shipping company on request, the costs for this depend on the postcode. Assembly: If required, our trained staff will be happy to assist you with the professional assembly and disassembly of your business equipment. Our recommendation: Let us know what you need... We will be happy to help you realize your projects, from planning to ordering to assembly.

Condition: new, Year of construction: 2024, functionality: fully functional, carrying capacity per cantilever arm: 140 kg, shelf height: 2,500 mm, total length: 3,150 mm, total height: 2,500 mm, axle spacing: 1,030 mm, load capacity per stand: 1,120 kg, approx. 3.15 running meters Cantilever rack with shelves 60 cm deep H: 250 cm 140 kg/arm META Multistrong Data : - H : approx. 250 cm - D : approx. 81 cm - L : approx. 315 cm - Cantilever arms : approx. 60 cm - Axial dimension : 103 cm - NEW GOODS immediately from stock. - 140 kg load per arm - 1120 kg load per upright - Uprights in RAL5010 (gentian blue). - Cantilever arms in RAL5010 (gentian blue). - Arms are hooked in and secured with locking bolts. - Arms adjustable in 70 mm increments. - Levels: Base + 4 storage levels (5 storage levels) Shelf consists of : - 04 x uprights, incl. base approx. 250 cm made of IPE120. - 16 x cantilever arms approx. 60 cm made of rectangular profile 40 x 30 mm. - 12 x META shelf, approx. 100 x 60 cm - incl. all necessary connecting elements and screws. Hedjy Uh Rmspfx Acdon -- Available immediately Price : 1765,00 € net 2100,35 € gross You will receive an invoice with VAT included. Accessories such as ground anchors, collision protection etc. can also be purchased from us. Transportation : The delivery is carried out on request by our partner forwarding agency, the costs depend on the postal code. Assembly : If required, our trained staff will be happy to assist you with the professional assembly and disassembly of your factory equipment. Our recommendation : Let us know what you need... We will be happy to help you with the realization of your projects, from planning and ordering to installation.

Condition: new, Year of construction: 2024, functionality: fully functional, carrying capacity per cantilever arm: 140 kg, shelf height: 2,500 mm, total length: 3,150 mm, total width: 810 mm, total height: 2,500 mm, axle spacing: 1,030 mm, load capacity per stand: 560 kg, approx. 3.15 running meters. Cantilever shelf H: 250 cm 140 kg/arm META Multistrong Data : - H : approx. 250 cm - D : approx. 81 cm - L : approx. 315 cm - Cantilever arms : approx. 60 cm - Axial dimension : 103 cm - NEW GOODS immediately from stock. - 140 kg load per arm - 1120 kg load per upright - Uprights in RAL5010 (gentian blue). - Cantilever arms in RAL5010 (gentian blue). - Arms are hooked in and secured with locking bolts. - Arms adjustable in 70 mm increments. - Levels: Base + 4 storage levels (5 storage levels) Shelf consists of : - 04 x uprights, incl. base approx. 250 cm made of IPE120. - 16 x cantilever arms approx. 60 cm made of rectangular profile 40 x 30 mm. - incl. all necessary connecting elements and screws. -- Available immediately Price : 1525,00 € net 1814,75 € gross You will receive an invoice with VAT included. Accessories such as ground anchors, collision protection etc. can also be purchased from us. Transportation : The delivery is carried out on request by our partner forwarding agency, the costs depend on the postal code. Hodpjy Uh Rgjfx Acden Assembly : If required, our trained staff will be happy to assist you with the professional assembly and disassembly of your business equipment. Our recommendation : Let us know what you need... We will be happy to help you with the realization of your projects, from planning and ordering to installation.