The product allows you to quickly recover the color metal that is isolated during an environmentally friendly process.
Solid Polish design ensures a very long life. We have every service part for your product.
• Cutting – top
• Steel wire extraction from aluminum braid (after installing additional attachment)
• Two drive system up-down
• Set of cut rollers 20-50 mm
• Set of cut rollers 50-100 mm
• Set of crush rollers
• Working voltage – 380 V
Cakdstlvec
• Motor power – 2,25 kW
• Weight – 277 k...
MG 220VZT Cable Granulation line (1200 Working hours) Complete with:
Pre-chopper 30 kW
over belt magnet system
in-feed bunker belt with top-roller magnet
MG 220VZT with Zig-Zag eject granulate nr 1
filter unit
Qil9z
Maximum Cable Diameter : Ø 90mm
Minimum Cable Diameter : Ø 5mm
Cutting Speed : 10 m / min
Cpkcxjce
Electric Motor Power : 4 kW
Machine Dimensions : 70cm x 131,5cm x 119cm
Machine Weight : 460 kg
Throughput: 300-350kg/h depends on sorting and kind of cables
Pre shredded cables up to 400kg/h
Connected load: 33 kW
Measurement: l x w x h ca. 4,0 m x 1,6 m = 6,4 m²
Input: Cable lengths up to max. 0,8m
K8vmurpuy
Diameter up to ca. 40mm
Single wire up to ca. 10mm m²
The MG Cable granulation installations are standard equipped with a Turbo. This Turbo is placed between the blade mill and the separation table and makes sure that the flexible wires (hairy wire) is being deformed and because of this it becomes more compact.
The separation is being done on the base of fraction size & weight differences. If you make the hairy wire more compact it becomes relatively heavier than the plastics/PVC. YOU HAVE A MUCH HIGHER END RESULT, NO COPPER LOSS (no copper in the...
This used MG Monster 125 cable granulator was serviced in our own workshop and equiped with new bearings, blades, sieves etc etc. and thus in top condition.
power: 7 kW
weight: 625 kg
Yuvotw
MİZAR S series are designed to strip and remove the outer covering material of any cable exposing the internal material. MİZAR cable stripper machine can easily strip and remove the outer covering material of any size cable. Including: Steel Wired Armoured cables (SWA), double steel wired armoured cables, steel tapes, PVC covered cables, lead covered cables, thick rubber covered cables, nylon covered cables, low-grade cables, TT cables and more provide excellent performance. Rotors feed with hyd...
compact system for recycling electrical cables consisting of a blade granulator with grid, pneumatic transport system, dry separator and dust filter.
installed power 7.15 Kw
hourly production of incoming cable 100 kg / h
B93k9eaafu
MİZAR CU Series are designed to separate the internal and external parts of any cable, thus preparing it to be recycled. MİZAR CU Series consist of three main systems of granulation, separation and blowers to effectively fragment and dismember 99,6% of the internal and external parts of any cables. The machine is fed with the required
material manually via a conveyor band or fed with MİZAR AC Series Pre-Shredder fully automatic within smart PLC software. The machine system operates on a single c...
MİZAR CU Series are designed to separate the internal and external parts of any cable, thus preparing it to be recycled. MİZAR CU Series consist of three main systems of granulation, separation and blowers to effectively fragment and dismember 99,6% of the internal and external parts of any cables. The machine is fed with the required material manually via a conveyor band or fed with MİZAR AC Series Pre-Shredder fully automatic within smart PLC software. The machine system operates on a single c...
MİZAR CU Series are designed to separate the internal and external parts of any cable, thus preparing it to be recycled. MİZAR CU Series consist of three main systems of granulation, separation and blowers to effectively fragment and dismember 99,6% of the internal and external parts of any cables. The machine is fed with the required material manually via a conveyor band or fed with MİZAR AC Series Pre-Shredder fully automatic within smart PLC software. The machine system operates on a single c...
MİZAR CU Series are designed to separate the internal and external parts of any cable, thus preparing it to be recycled. MİZAR CU Series consist of three main systems of granulation, separation and blowers to effectively fragment and dismember 99,6% of the internal and external parts of any cables. The machine is fed with the required
Pgaowyfz
material manually via a conveyor band or fed with MİZAR AC Series Pre-Shredder fully automatic within smart PLC software. The machine system operates on a...
Throughput: 300 - 350kg/h depends on sorting and kind of cables
Pre shredded cables up to 200 - 400kg/h
2pshmm
Connected load: 33 kW
Measurement: l x w x h ca. 4,0 m x 1,6 m = 6,4 m2
Input: Cable lengths up to max. 0,8m
Diameter up to ca. 40mm
Single wire up to ca. 10mm2
Autonomous system for cable and radiator recycling. consisting of a blade granulator, grid, pneumatic transport, dry separator
installed power 48 Kw
Jx29wm
production 900 Kg / h
The compact "SINCRO" equipment line enables easy and efficient non-ferrous cable with a new "dry" processing method - The cables are first shredded into similar pieces in a granulator. then the copper or aluminum is automatically separated from the plastic ( PVC or polyethylene insulation material )
All SINCRO units are equipped with a granulator with blades, a vibrating and air-blowing separation table to fluidize the material to be separated
A built-in filter system prevents dust emission int...
Functional Description:
Bjcgblxgn8
This forward-looking rotor bucket ensures quick and clean transfer of compost and other bulk materials. The material is picked up in the same way as with a conventional wheel loader shovel. At the discharge point, the rotor is started by means of the automatic control. The hydraulic rear wall pushes the material evenly to the rotor depending on the rotor speed. The counter-rotating rotor mills off the bucket contents, mixing it well and discharging it loosely. ...
The MDS-1 Electric Motor Recycling Machine designed to accurate copper extraction from stator insert of electric motor with different types of diameter.
Description:
K8cl9tw
The machine use steel claws to extract copper from the stator shell during backward movement.
Stator fixed on special rollers mounted on lifted platform, a holder located in front of the machine keeps the stator from moving. Steel claws release copper when the operator pulls leaver backward.
The machine fitted on solid fra...
Also different models avaliable !
70qpjhx0i
1. Briquette Diameter: Ø 120mm
2. Capacity : 1800 – 2200 kg / hour (Iron & Steel)
3. Preliminary Compression Ram Thrust: 15 tons
4. Main Compression Cylinder Thrust: 400 tons
5. Maximum Working Pressure: 300 bars
6. Cycle Time : 12 - 14 sec
7. Electric Motor Power: 75 kW
8. Machine Dimensions (Width x Length x Height): 3200mm x 4200mm x 3500mm
9. Machine Weight: 13.000 kg
10. Screw drive feeders will fill the compression chamber automatically and bu...
Meetra M3P.32 transplanter
Attachment for tractors (3 point hydraulics) for active transfer of compost and soil etc.
The M3P.30 compost spreader is designed to be mounted on a 3-point hydraulic system (KAT II or KAT III) for tractors with a power of approx. 90 HP. The spreader is driven by the tractor's power take-off (540 rpm). The rotor then turns at 180 rpm.
For road transport, the machine can be manually swivelled to the rear.
The track scrapers automatically adjust to the unevenness of the ...
ZLOMIARZE Recycling Technology - LRK Recycling line
The Mini Line is a high quality set of devices designed for the recycling process. Shredding and separation are essentials in this business, that’s why Mills from TORNADO series was designed for rapid reaction on feeding materials with being in a chamber for short time. Suitable sieves placement and balanced cutting rotor RPM provide uniform material fraction.
Innovated implementation of water system with adjustable pressure in the Wet Separat...
Built on order
The sink-float separator STF 3.0 is perfectly matched to our high efficiency SP1000 Mk2 centrifuge and together with these centrifuges forms a compact but highly capable washing line that requires little maintenance and can wash/sort up to 3000 Kg/hour of hard plastics.
The machines are fully constructed in stainless steel 304 so that salt solutions can be used without any problems. Additional peripherals such as water purification, transport screws and big bag loading stations ...
The compact vibratory table with dual magnetic separation is designed for precise separation of the smallest low magnetic particles. The built-in magnetic belt separator (SM-500) removes all thicker fractions. An automatic magnetic drum is used at the end of the vibratory table to improve accuracy.
Made of strong permanent magnets with suitable arrangement. The result is that the appliance separates the fraction, even of 1 mm low ferromagnetic acid-resistant steel.
Intoqti
Application :
✔ Cable...
Also different models avaliable !
1. Bale Size: 600mm x 400mm x ...
2. Container Dimension (Width x Length x Height): 620mm x 1300mm x 620mm
3. Capacity: 0,8 – 1,2 tons / hour ( Iron - Steel )
4. Bale Weight: 45 – 100 kg
5. Cycle Time: 90 seconds
6. Top Cover Cylinder Pressure: 63 tons
7. Main Compression Cylinder Pressure: 110 tons
8. General Working Pressure : 250 bar
9. Machine Dimensions (Width x Length x Height) : 2120mm x 4350mm x 1320mm
10. Electric Motor: 15 kW
11. Machine Weight: 6.8...
Built on order
Vibrating sieve to filter the process water.
B8t0m7r09c
Process water is preferably used in a closed circuit. The authorities also see this as the ideal solution. Obtaining the permits for a recycling plant is greatly simplified by the use of a closed circuit and the costs of using the plant are significantly lower.
ZŁOMIARZE Recycling Technology MCW 52/76 Shredder
The MCW series quad shaft shredder is based on many years of experience in the plastics and scrap industry. MCW Shredder is a highly reliable, universal pre-shredder for shredding a wide range of materials such as plastics, materials, rubber, wires, electronic scrap, post-production waste as well as slight magnetic materials.
Types of MCW Shredders:
MCW-52
Technical Specification:
• Motor output – 22 kW
• Cutting Chamber – 510 × 760 mm
• Perfo...
- Cutting Force : 1100 Tons
- Capacity : up tp 50 tons per hour
- Side Compression Force : 2 x 120 Tons
- Clemp Compression Force : 160 Tons
- Electric Motor : 264 kW
- Machine Weight : 85.000 kg
- PLC Controlled
- Remote Control Avaliable
Jujwma
- Output Length Adjustable
1. Electric Motors Total Power: 360 kW
2. Machine Weight: 44.000 kg
3. Shredding Capacity : 10 - 15 tons/h (Iron & Steel)
4. Blade Quantity : 78, Blade Thickness : 150 mm.
5. Loading Chamber Dimensions : 2350 x 4085 mm
6. Shredding Chamber Dimensions : 1500 x 2000 mm
7. Replacament and maintenance of the blades can be easily done from top of the chamber.
8. Cutting blades are made of material No: 2767
9. Main shafts are made of material : 42 CrMo4 , 32-34 HRC (Twisting and breaking resistant )
1...
- Cutting Force : 900 Tons
- Capacity : up tp 25 tons per hour
- Side Compression Force : 2 x 120 Tons
- Clemp Compression Force : 160 Tons
- Electric Motor : 220 kW
- Machine Weight : 78.000 kg
- PLC Controlled
Bu8sfniii0
- Remote Control Avaliable
- Output Length Adjustable
- Cutting Force : 1400 Tons
- Capacity : up tp 70 tons per hour
- Side Compression Force : 2 x 220 Tons
- Clemp Compression Force : 250 Tons
- Electric Motor : 480 kW
- Machine Weight : 150.000 kg
- PLC Controlled
- Remote Control Avaliable
- Output Length Adjustable
Xwla3cq
Also different models avaliable !
1. Bale Size: 500mm x 500mm x.
2. Container Dimensions (Width x Length x Height): 2000mm x 2500mm x 1100mm
3. Capacity: 15-20 ton / hour (steel)
4. Cycle Time: 90 seconds ( Idle )
5. Top Cover Cylinder Thrust: 90 tons
6. Preliminary Compression Cylinder Thrust: 150 tons
7. Main Compression Ram Thrust: 300 tons
8. Maximum Working Pressure: 300 bars
9. Electric Motor: 2 x 75 kW = 150 kW
10. Machine Dimensions (Width x Length x Height): 10000 mm x 10000 mm x...
Also different models avaliable !
1. Bale Size : 400 mm x 400 mm x...
2. Press Box Dimensions ( W x L x H ) : 1000 mm x 2700 mm x 900 mm
3. Loading Bunker Dimensions ( W x L x H ) : 1650 mm x 2300 mm x 800 mm
4. Feeding Opening ( W x L ) : 1000 mm x 1600 mm
5. Capacity : 4-6 ton / h ( Aluminum , 12-19 ton / h ( Copper ) , 11-17 ton / h ( Steel )
6. Cycle Time : 30 seconds
7. Preliminary Compression Thrust : 140 Tons
8. Secondary Compression Thrust : 210 Tons
9. Main Compression Thrust : 290 T...
Different models are also available!
1.Bale Size: 400mm x 400mm x ...
2. Printing Box Dimensions (W x L x H): 1000 mm x 2600 mm x 900 mm
3. Loading Bunker Dimensions (W x L x H): 1400 mm x 1850 mm x 500mm
4. Feed opening (W x L): 1000 mm x 1600 mm
5. Capacity: 3-4 tons / hour (Aluminum, 13-15 tons / hour (Copper), 9-10 tons / hour (Steel)
6. Cycle Time: 45 seconds
7. Pre-Compression Push Printing: 120 Ton
8. Secondary Compression Push: 120 Ton
9. Main Compression Push Printing: 220 Ton
10. Work...
Also different models avaliable !
1. Briquette Diameter: Ø 80mm
2. Capacity : 700-900 kg/hour ( Copper )
3. Preliminary Compression Ram Thrust: 12.5 tons
4. Main Compression Cylinder Thrust: 250 tons ( 5 tonne / cm2 )
5. Maximum Working Pressure: 300 bars
6. Cycle Time : 12 - 14 sec
7. Electric Motor Power: 30 kW
8. Machine Dimensions (Width x Length x Height): 2200 mm x 2600 mm x 2800 mm
9. Machine Weight: 6.000 kg
10. Screw drive feeders will fill the compression chamber automatically a...
- Cutting Force : 700 Tons
- Capacity : up tp 20 tons per hour
- Side Compression Force : 2 x 85 Tons
- Clemp Compression Force : 100 Tons
- Electric Motor : 160 kW
- Machine Weight : 55.000 kg
- PLC Controlled
- Remote Control Avaliable
- Output Length Adjustable
Hpl0erzic
Blade Length : 620mm
Cutting Speed : 5 cut/min.
Cutting Force : 70 ton
Cylinder Diameter : Ø160mm
Working Pressure : 220 bar
Electric Motor Power : 11 kW
Machine Weight : 2.500kg
Cdae3m20
Machine Dimensions : 750 mm x 2500 mm x 1300 mm
1. Electric Motors Total Power: 180 kW
2. Machine Weight: 20.000 kg
3. Shredding Capacity : 10 15 t / h (Copper)
4. Blade Quantity : 90, Blade Thickness : 100 mm.
5. Loading Chamber Dimensions : 1600 mm x 2400 mm
6. Shredding Chamber Dimensions : 1000 mm x 1600 mm
7. Replacament and maintenance of the blades can be easily done from top of the chamber.
8. Cutting blades are made of material No: 2767
9. Main shafts are made of material : 42 CrMo4 , 32-34 HRC (Twisting and breaking resistant )
10. ...
1. Electric Motors Total Power: 2 x 45 = 90KW
2. Machine Weight: 12.000 kg
3. Shredding Capacity : 3 - 4 tons / h ( Aluminum profiles , barrels, fridge etc steel thickness up to 3 mm and waste )
4. Cutting blades are made of material HARDOX 500 .Blade thickness is 6 cm and coated with HRC 60 hardfilled
welding. Blades are easy to replace.
5. Loading Chamber Dimensions : 800 mm x 1200 mm
6. The walls will be covered with HARDOX 500 material.
7. Before painting, whole machine body will be sand bla...
- Cutting Force : 1250 Tons
- Capacity : up tp 50 tons per hour
- Side Compression Force : 2 x 180 Tons
- Clemp Compression Force : 250 Tons
- Electric Motor : 396 kW
Bu8sky7nrm
- Machine Weight : 120.000 kg
- PLC Controlled
- Remote Control Avaliable
- Output Length Adjustable
Blade Length : 820mm
Cutting Speed : 6 - 8 cut/min.
Cutting Force : 100 ton
Cylinder Diameter : Ø200mm
Working Pressure : 250 bar
Electric Motor Power : 30 kW
Machine Weight : 6.000kg
Beoukijg8p
Machine Dimensions : 150cm x 300cm x 150cm
The Machineseeker Trust Seal enables buyers to quickly recognize whether they are dealing with a trustworthy seller.
What do we verify?
Check of trade licence or commercial register extract
Verification of the dealer's postal address
Validation of the banking details
Verification of accessibility to main phone number
Credit report may not contain negative criteria
Buyer complaints can lead to withdrawal of the seal
What does this mean for the seller?
After successful verification, we will include the seal awarded to you in your listings on Machineseeker. In this way, you signal to any potential buyer the independently verified seriousness of your company. This creates buyer confidence and increases the likelihood of successfully selling machines. In addition, you have the option of including the Maschinensucher seal of confidence on your homepage and letterhead.