Conveyor belt with cycle control

MASS NDZ 2 mit Taktsteuerung

Condition: used, Year of construction: 2004, Technical details: Caodpfxou Ix Ize Ab Tea turning diameter over bed: 850 mm turning dia. over face-slide: 580 mm turning length: 4000 mm centre distance: 4000 mm faceplate diameter: 800 mm control: Siemens 810D revolution per minute: 1 - 1600 / 2 step U/min max. torque on the spindle: 6000 Nm feed motor: X= plan + Z= längs: 16000 / 20000 N rapid motion - x-axis: 4 m/min rapid motion - y-axis: 7 m/min spindle passage: 130 (Spindelkopf DIN 55027 Gr. 11) mm operating hours - idle run: werden noch ausgelesen h tailstock taper ISO: MK 6 tailstock quill stroke: 350 mm max. workpiece weight between centers: 5000 kg max. workpiece weight -without tailstock: 1800 kg interface: RS 232 / V24 voltage: 400 V / 50Hz V control voltage: 24 V Gleichstrom V total power requirement: ca. 52 kW Weight approx.: 14,0 t dimension machine xH: 2,6 x 9,1 x 2,5 m Cycle lathe with Siemens cycle control Motor: 37kW, rated speed 1500 rpm; max. speed 6500 rpm; torque 235 Nm Two gear shift stages Stage II: Spindle torque 258.9 to 1364.6 Nm Stage I: Spindle torque 1050.4 - 5536.1 Nm Feed drive Three-phase servo drive 2x chip conveyor Double E-cabinet Quick-change steel holder parat Coolant device incl. various accessories see photo, as well as steady rest and 3-jaw chuck Ø 500mm Rota-S plus *

Year of construction: 1984, condition: ready for operation (used), Rafamet UBB 112/2 Csdpfx Ajhvml Ijb Tjaa Wheel Tread Diameter Minimum 700 mm Wheel Tread Diameter Maximum 1120 mm Clamping length 540 - 1050 mm Wheelset Axle Length Minimum 1640 mm Wheelset Axle Length Maximum 2800 mm Maximum Tire Width 150 mm Maximum Wheelset Weight 4000 kg Saddle Set Up Motion Speed 2000 mm/min Saddle Feed Maximum 2000 mm/min Main Drive Motor Power 80 kW Weight aprox 40000 kg

Condition: good (used), used boring machine Casdeh Ryc Hspfx Ab Toa Brand: Juaristi Model: MDR 75 Weight: 5600kg Motor power: 10KW 2-axis digital FAGOR. Shank diameter: 75mm Longitudinal course (X axis): 1,150mm Vertical course (Y axis): 700mm Column transversal course (Axis W): 800mm Cane exit course (Z axis): 500mm Table surface: 900x700mm Speeds: 22-1055rpm Number of advances: 9 of 0.04-3 mm/rev.

Year of construction: 1978, condition: excellent (used), machine/vehicle number: 2751, General / technical data: Hydraulic horizontal internal broaching machine in in good technical condition Manufacturer: Karl Klink Model: RIW 6,3 Caedeiw Dlkspfx Ab Tsa Machine No: 2751 Year of manufacture: 1978 Weight: 2,3to tractive force: 6,3t broaching speed: hydraulically infinitely variable from 1m/min to 7m/min Return speed: hydraulically stepless adjustable from 7m/min to 25m/min maximum stroke: 1320mm maximum workpiece diameter: max. 420mm table opening: Ø 80mm dimensions: (w x d x h) approx. 5.700mm x 600mm x 1.900mm power supply: 380 Volt / 50 Hz / 4kW Accessories/ optional equipment: - Coolant / lubricant system - without tool feeder - Oil and chip tray (approx. 2,000mm) Remark: The machine is ideal for the production of keyways. Broaches as well as broaching mandrels can be supplied on request. The machine is ready for demonstration under power in our warehouse.

Year of construction: 1985, condition: ready for operation (used), Table dimension: 1435x460mm, T-groove number/ width/ distance: 5/ 16/ 80mm, controls: TNCi-120, length: 1435mm, width: 2330mm, height: 1648mm, weight: 3,1t, with documentation, accessories are available, no defects known, an inspection is possible. Caodpelbmupjfx Ab Tja

Year of construction: 2025, condition: as good as new (ex-display), Air-cooled process chiller: R32 refrigerant Cedpfx Aef H A Eyob Tjaa Cooling capacity 72 kW at 7/12°C, internal P3 pump, internal 410 l tank, winter package down to -25°C ambient temperature for outdoor installation, includes variable-speed fans Large Dixell display with protective cover

Condition: refurbished (used), Year of construction: 1974, functionality: fully functional, machine/vehicle number: 1276, CNC Hot Radial Forging GFM SX-13 New in 1974 / 2022 New control system PLC SIEMENS S7 Machine number: 1276 No. of Hammers: 4 Forging force each hummer: 160 Ton Hammer stroke / min: 700/min Hammer lenght: 240 mm Diameter setting range: 80 mm Maximum forging diameter: Structural steel, round-cross section: Ø 130 mm square cross section: Ø 115 mm Smallest dimensions forged: Ø 25 mm Manipulator A max. displacement: 6820 mm Manipulator B max. displacement: 7150 mm Maximum workpiece length: 6000 mm Rapid speed manipulator: 400mm/sec Total connected power: 300 kW 380 V, 50 Hz Machine dimensions: Forging height over floor: 615 mm Total height pf the machinr over floor: 1665 mm Total machine lenght: 32670 mm Total foundation lenght: 33400 mm Tot. machine width (without auxliary equipments): approx 3885 mm Total foundation width: 16000 mm Codpfx Abjq U R T No Toaa Total weight of the machine: 84.000 Kg

Condition: used, turning diameter over bed 2400 mm turning diameter over slide rest 2200 mm turning length 10000 mm power capacity 185 kW faceplate diameter 1650 mm turning speeds 1,5 -150 U/min max. workpiece weight 70000 kg clamping diameter 1400 mm Technical data Working range Maximum turning diameter over support: 2200 mm Maximum swing diameter over bed: 2400 mm Maximum turning length: 10,000 mm Clamping diameter in the headstock faceplate: 300 - 1,600 mm with special jaws up to 2,050 mm Clamping diameter in the tailstock faceplate: 300 - 1,400 mm Maximum workpiece weight: 70000 kg Main drive, faceplate Faceplate diameter: 2000 mm Faceplate speeds, continuously adjustable in 4 stages: 1.5 - 150 rpm Maximum torque at rated speed: 220,000 Nm Drive power of main motor: 185 kW Flange centre point angle: 70° Supports Travel of the plunge slide: 500 mm Travel of the face slide: 1400 mm Quick adjustment, longitudinal: 2000 mm/min Quick adjustment, face: 800 mm/min Infinitely variable feed, longitudinal: 0.6 - 300 mm/min Infinitely variable feed, face: 0.3 - 120 mm/min Max. cutting force at support: 20,000 kg Tailstock Faceplate diameter (removable): 1650 mm Faceplate clamping diameter: 1400 mm Flange centre point angle: 70° Quick adjustment: 1250 mm/min Special equipment Copying device for first support Copying length 8500 mm Max. copying depth in one pass 500 mm Casdpexddvnofx Ab Tsa Boring device: Boring bar 460 x 390 mm Drilling diameter 600 - 1000 mm Maximum drilling depth in one pass 2700 mm At Ks of 200 kp/mm² - s max. = 1.5 mm/rev a = max. chip cross-section 30 mm² at a projection of 1000 mm Reduced chip cross-section with increasing drilling depth A guide ruler for cone turning, adjustment angle up to 8° and a maximum cone length (in one pass) of 2000 mm, adjustment accuracy ± 5 minutes. A guide ruler for cone turning, adjustment angle up to 15° and a maximum cone length (in one pass) of 1000 mm, adjustment accuracy ± 5 minutes. 125 kg auxiliary crane on spindle box.

Condition: reconditioned (used), travel distance X-axis: 10,000 mm, travel distance Y-axis: 1,300 mm, travel distance Z-axis: 2,100 mm, rapid traverse X-axis: 30 m/min, rapid traverse Y-axis: 30 m/min, rapid traverse Z-axis: 30 m/min, feed rate X-axis: 30 m/min, feed rate Y-axis: 30 m/min, feed rate Z-axis: 30 m/min, spindle speed (max.): 6,000 rpm, spindle speed (min.): 36 rpm, rotational speed (max.): 6,000 rpm, tank capacity: 1,200 l, SHW Powerspeed 5 Travel paths • X-axis (bed): 10,000 mm • Y-axis (headstock): 1,300 mm • Z-axis (vertical): 2,100 mm Control Cedpfx Abjv Dhw Ts Tsaa • CNC control: Heidenhain iTNC 530 Feed rate • X, Y and Z axes: 30,000 mm/min • Acceleration: 3.5 m/s² Universal milling head in orthogonal design • Milling head holder swivel range: 360 x 1 degree • Milling head swivel range: 180 x 1 degree • Tool holder: SK 50 DIN 69871 • Speed range: 36 - 6,000 rpm Chip conveyor • Feed length: 10,000 mm Coolant system • Container capacity: 1,200 Liter ATTENTION the images are comparison images About us: MBM Maschinenservice & Gebrauchtmaschinen GmbH is an independent specialist for SHW machine tools. Our main focus is on tool milling machines. Our services include spare parts deliveries, on-site customer service, machine overhauls and control system modernizations. Services: - Used machines - Spare parts - Customer service - Machine service - Machine overhauls - Control system modernization _____ Used machine - used milling machine - used traveling column milling machine - orthogonal milling head - metalworking - tool milling machine - milling head - SHW machine - SHW spare parts - used milling machine - used milling machine - used CNC milling machine - used drilling and milling machine - used metal milling machine - used metal milling machine - used metal milling machine - used CNC milling machine - CNC milling machines - CNC milling machines - milling machine - large part machining - large part machining - large part machining - CNC large part machining - milling - shw - PS5 - PS 5 - Powerspeed - SHW PSZ 5 - SHW Powerspeed - SHW Powerspeed 5 - PSZ 5 - PSZ 5 - Heidenhain - MBM milling machine - MBM machine - column milling machine

Condition: used, Year of construction: 2016, Technical details: Csdpfoudf Evox Ab Tjaa weight: 22 t