Used Romer Electrostatic for sale (252)

Condition: new, Year of construction: 2025, Curing ovens shown in the photos can vary in price depending on size, configuration, and optional features. 💡📏⚙️ At ROMER, we manufacture both standard models and fully bespoke solutions, tailored to your process requirements. 🏭✅ Tell us your part size, line capacity, curing profile, and available space - and we will propose the best setup and the options that actually improve daily performance. 🔥🎯 🧠📡 Control and monitoring Live process control for temperature, time, airflow, and modes - with alarms and saved recipes for repeatable cycles. 🔁✅ 🔥🧩 Heating module Fast heat-up and stable temperature thanks to efficient heating elements and quick energy transfer. ⚡🌡️ 🌀💨 Air circulation Uniform airflow reduces temperature differences for consistent coating quality. 🎯✅ 🧱❄️ Insulation and design Smart chamber construction minimizes heat loss - faster reaching setpoint, lower consumption. ♻️📉 Lhjdpfx Aoyg H Erob Asn 🛡️⚠️ Safety and certification Sensors, interlocks, and protection logic increase safety and reliability. 🔒👷 ⚡💰 High efficiency Optimized heat transfer and reduced losses mean real operating savings. 📉🔥 ⏰🤖 Automatic start Programmable schedule - automatic preheating before the shift for smoother production starts. ⏱️✅ 🚪🔒 Self-latching doors + intelligent chimney Prevents accidental opening, chimney activates only when needed for safer operation. 🧯✅ 🌿🔋 ECO mode Low-energy standby when idle - fuel consumption reduction up to 20% (depending on process). 🌱📉 👀💡 View and lighting Inspection without opening the door - fewer temperature drops, easier supervision. ✨👁️ 🛤️🔥 Guide rails + automatic hood Heat hood runs only during loading to reduce temperature loss, automatic rail infeed improves ergonomics and loading speed. 🙌⚙️ 🎛️🌡️ MULTI-ZONE HEAT Independent zone control for uniform curing of parts with different mass and geometry. 🧩✅ 🧠♨️ MTS system Heating elements mounted without thermal bridges - higher efficiency and faster time to set temperature. ⚡⏱️ 2-in-1 🧱↔️🧱 Split chamber Movable partition for two independent zones - drying and curing in one unit for maximum flexibility. 🚀🔁 🎚️🌀 VFD ventilation Variable fan speed based on chamber conditions - better control and lower electricity use. ⚙️💡

Condition: new, Year of construction: 2025, Curing ovens shown in the photos can vary in price depending on size, configuration, and optional features. 💡📏⚙️ At ROMER, we manufacture both standard models and fully bespoke solutions, tailored to your process requirements. 🏭✅ Tell us your part size, line capacity, curing profile, and available space - and we will propose the best setup and the options that actually improve daily performance. 🔥🎯 🧠📡 Control and monitoring Live process control for temperature, time, airflow, and modes - with alarms and saved recipes for repeatable cycles. 🔁✅ 🔥🧩 Heating module Fast heat-up and stable temperature thanks to efficient heating elements and quick energy transfer. ⚡🌡️ 🌀💨 Air circulation Uniform airflow reduces temperature differences for consistent coating quality. 🎯✅ 🧱❄️ Insulation and design Smart chamber construction minimizes heat loss - faster reaching setpoint, lower consumption. ♻️📉 🛡️⚠️ Safety and certification Sensors, interlocks, and protection logic increase safety and reliability. 🔒👷 ⚡💰 High efficiency Optimized heat transfer and reduced losses mean real operating savings. 📉🔥 ⏰🤖 Automatic start Programmable schedule - automatic preheating before the shift for smoother production starts. ⏱️✅ 🚪🔒 Self-latching doors + intelligent chimney Prevents accidental opening, chimney activates only when needed for safer operation. 🧯✅ 🌿🔋 ECO mode Low-energy standby when idle - fuel consumption reduction up to 20% (depending on process). 🌱📉 👀💡 View and lighting Inspection without opening the door - fewer temperature drops, easier supervision. ✨👁️ 🛤️🔥 Guide rails + automatic hood Heat hood runs only during loading to reduce temperature loss, automatic rail infeed improves ergonomics and loading speed. 🙌⚙️ 🎛️🌡️ MULTI-ZONE HEAT Independent zone control for uniform curing of parts with different mass and geometry. 🧩✅ Ledpfx Absyg H Dhe Ashn 🧠♨️ MTS system Heating elements mounted without thermal bridges - higher efficiency and faster time to set temperature. ⚡⏱️ 2-in-1 🧱↔️🧱 Split chamber Movable partition for two independent zones - drying and curing in one unit for maximum flexibility. 🚀🔁 🎚️🌀 VFD ventilation Variable fan speed based on chamber conditions - better control and lower electricity use. ⚙️💡

Condition: new, Year of construction: 2025, Curing ovens shown in the photos can vary in price depending on size, configuration, and optional features. 💡📏⚙️ At ROMER, we manufacture both standard models and fully bespoke solutions, tailored to your process requirements. 🏭✅ Tell us your part size, line capacity, curing profile, and available space - and we will propose the best setup and the options that actually improve daily performance. 🔥🎯 🧠📡 Control and monitoring Live process control for temperature, time, airflow, and modes - with alarms and saved recipes for repeatable cycles. 🔁✅ 🔥🧩 Heating module Fast heat-up and stable temperature thanks to efficient heating elements and quick energy transfer. ⚡🌡️ Lhedpfxjzdupls Ab Aon 🌀💨 Air circulation Uniform airflow reduces temperature differences for consistent coating quality. 🎯✅ 🧱❄️ Insulation and design Smart chamber construction minimizes heat loss - faster reaching setpoint, lower consumption. ♻️📉 🛡️⚠️ Safety and certification Sensors, interlocks, and protection logic increase safety and reliability. 🔒👷 ⚡💰 High efficiency Optimized heat transfer and reduced losses mean real operating savings. 📉🔥 ⏰🤖 Automatic start Programmable schedule - automatic preheating before the shift for smoother production starts. ⏱️✅ 🚪🔒 Self-latching doors + intelligent chimney Prevents accidental opening, chimney activates only when needed for safer operation. 🧯✅ 🌿🔋 ECO mode Low-energy standby when idle - fuel consumption reduction up to 20% (depending on process). 🌱📉 👀💡 View and lighting Inspection without opening the door - fewer temperature drops, easier supervision. ✨👁️ 🛤️🔥 Guide rails + automatic hood Heat hood runs only during loading to reduce temperature loss, automatic rail infeed improves ergonomics and loading speed. 🙌⚙️ 🎛️🌡️ MULTI-ZONE HEAT Independent zone control for uniform curing of parts with different mass and geometry. 🧩✅ 🧠♨️ MTS system Heating elements mounted without thermal bridges - higher efficiency and faster time to set temperature. ⚡⏱️ 2-in-1 🧱↔️🧱 Split chamber Movable partition for two independent zones - drying and curing in one unit for maximum flexibility. 🚀🔁 🎚️🌀 VFD ventilation Variable fan speed based on chamber conditions - better control and lower electricity use. ⚙️💡

Condition: new, Year of construction: 2025, Curing ovens shown in the photos can vary in price depending on size, configuration, and optional features. 💡📏⚙️ At ROMER, we manufacture both standard models and fully bespoke solutions, tailored to your process requirements. 🏭✅ Tell us your part size, line capacity, curing profile, and available space - and we will propose the best setup and the options that actually improve daily performance. 🔥🎯 🧠📡 Control and monitoring Live process control for temperature, time, airflow, and modes - with alarms and saved recipes for repeatable cycles. 🔁✅ 🔥🧩 Heating module Fast heat-up and stable temperature thanks to efficient heating elements and quick energy transfer. ⚡🌡️ 🌀💨 Air circulation Uniform airflow reduces temperature differences for consistent coating quality. 🎯✅ 🧱❄️ Insulation and design Smart chamber construction minimizes heat loss - faster reaching setpoint, lower consumption. ♻️📉 🛡️⚠️ Safety and certification Sensors, interlocks, and protection logic increase safety and reliability. 🔒👷 ⚡💰 High efficiency Optimized heat transfer and reduced losses mean real operating savings. 📉🔥 ⏰🤖 Automatic start Programmable schedule - automatic preheating before the shift for smoother production starts. ⏱️✅ 🚪🔒 Self-latching doors + intelligent chimney Prevents accidental opening, chimney activates only when needed for safer operation. 🧯✅ 🌿🔋 ECO mode Low-energy standby when idle - fuel consumption reduction up to 20% (depending on process). 🌱📉 👀💡 View and lighting Inspection without opening the door - fewer temperature drops, easier supervision. ✨👁️ 🛤️🔥 Guide rails + automatic hood Heat hood runs only during loading to reduce temperature loss, automatic rail infeed improves ergonomics and loading speed. 🙌⚙️ 🎛️🌡️ MULTI-ZONE HEAT Independent zone control for uniform curing of parts with different mass and geometry. 🧩✅ 🧠♨️ MTS system Heating elements mounted without thermal bridges - higher efficiency and faster time to set temperature. ⚡⏱️ 2-in-1 🧱↔️🧱 Split chamber Lodpfx Ajflk Awsb Aehn Movable partition for two independent zones - drying and curing in one unit for maximum flexibility. 🚀🔁 🎚️🌀 VFD ventilation Variable fan speed based on chamber conditions - better control and lower electricity use. ⚙️💡

Condition: new, Year of construction: 2025, Curing ovens shown in the photos can vary in price depending on size, configuration, and optional features. 💡📏⚙️ At ROMER, we manufacture both standard models and fully bespoke solutions, tailored to your process requirements. 🏭✅ Tell us your part size, line capacity, curing profile, and available space - and we will propose the best setup and the options that actually improve daily performance. 🔥🎯 🧠📡 Control and monitoring Live process control for temperature, time, airflow, and modes - with alarms and saved recipes for repeatable cycles. 🔁✅ 🔥🧩 Heating module Fast heat-up and stable temperature thanks to efficient heating elements and quick energy transfer. ⚡🌡️ 🌀💨 Air circulation Uniform airflow reduces temperature differences for consistent coating quality. 🎯✅ 🧱❄️ Insulation and design Smart chamber construction minimizes heat loss - faster reaching setpoint, lower consumption. ♻️📉 🛡️⚠️ Safety and certification Sensors, interlocks, and protection logic increase safety and reliability. 🔒👷 ⚡💰 High efficiency Optimized heat transfer and reduced losses mean real operating savings. 📉🔥 ⏰🤖 Automatic start Programmable schedule - automatic preheating before the shift for smoother production starts. ⏱️✅ 🚪🔒 Self-latching doors + intelligent chimney Prevents accidental opening, chimney activates only when needed for safer operation. 🧯✅ 🌿🔋 ECO mode Low-energy standby when idle - fuel consumption reduction up to 20% (depending on process). 🌱📉 👀💡 View and lighting Inspection without opening the door - fewer temperature drops, easier supervision. ✨👁️ 🛤️🔥 Guide rails + automatic hood Heat hood runs only during loading to reduce temperature loss, automatic rail infeed improves ergonomics and loading speed. 🙌⚙️ 🎛️🌡️ MULTI-ZONE HEAT Independent zone control for uniform curing of parts with different mass and geometry. 🧩✅ 🧠♨️ MTS system Heating elements mounted without thermal bridges - higher efficiency and faster time to set temperature. ⚡⏱️ 2-in-1 🧱↔️🧱 Split chamber Lhsdofz U Nbopfx Ab Ajn Movable partition for two independent zones - drying and curing in one unit for maximum flexibility. 🚀🔁 🎚️🌀 VFD ventilation Variable fan speed based on chamber conditions - better control and lower electricity use. ⚙️💡

Year of construction: 2020, condition: new, 7" Touchpad Large color touch panel looks aesthetically and uses comfortably and intuitively. Set on it all the important parameters.Memory 20 programs each with 10 events You can save up to 20 programs and activate up to 10 consecutive events time-temperature arranged in the heating curve. This is especially needed for the more demanding process.Information about consumption of power Lodjfz U Tiepfx Ab Aohn Consumption is calculated based on the settings of the burner. This feature will allow you to estimate the cost of the cycle, consumption and plan check staff.Recorder of cycle USB Each of the ovens is equipped with two-channel temperature recording on USB flash drive.. Each file is automatically created and is responsible for a separate cycle are recorded temperature extremes, hour and minute measurement. Files are saved in * .csv (Excel sheet) For all buyers the end of 2016 option is free, the competition for the option you have to pay up to several thousand euros. History 20 latest of burn Something's wrong? and perhaps too few overbroad elements from the oven? Now you check thoroughly oldest and lastest burning parameters, how often took, whether cycle proceeds without any problems, what was the consumption and when they ran. Start the oven automatically at 6 am How many times have you stay after hours and expecting end of the cycle? If you own a powder coating plan that works for a long time, You know exactly what we are talking about. With our solution you can leave cycle not cured in the oven, to automatically end when you come to the job next morning.

Condition: new, Year of construction: 2025, A typical coating system consists of surface pretreatment (cleaning and/or application of a conversion coating), intermediate drying, an electrostatic coating zone (booth/powder coating station), and a curing oven. The workpieces are transported through the system by a conveyor system. Our company, ROMER®, plans, manufactures, and assembles complete powder coating lines. Our systems can be inspected and tested at our facility in Hürth near Cologne. Lodpfscv Nl Rsx Ab Aehn Request a quote for a system tailored to your specific application.

Condition: like new (used), Year of construction: 2026, functionality: fully functional, operating hours: 12 h, power: 30 kW (40.79 HP), input voltage: 380 V, temperature: 200 °C, inner dimension length: 1,200 mm, inner dimension width: 1,700 mm, inner dimension height: 2,300 mm, total length: 1,500 mm, total width: 2,200 mm, total height: 2,800 mm, overall weight: 400 kg, number of chambers: 1, control type: PLC-controlled, Equipment: CE marking, Professional Composite Curing Oven – Romer SL Internal Dimensions: 1200 × 1700 × 2300 mm High-performance industrial composite curing oven from the respected Polish manufacturer Romer, designed for advanced composite manufacturing processes including carbon fiber prepreg curing, drying, post-curing, and thermal processing applications. This electric batch oven is ideal for aerospace, automotive, marine, motorsport, and industrial composite production environments where accurate and stable temperature control is essential. Constructed with a heavy-duty steel frame, stainless steel internal chamber panels, and durable powder-coated external finish, the oven is built for continuous industrial operation and long-term reliability. The smart control system delivers precise temperature management, efficient power consumption, and controlled heating/cooling performance. The integrated air circulation and ventilation system ensures uniform heat distribution throughout the chamber for consistent curing quality. Key Features: • Maximum operating temperature: 200°C • Internal dimensions: 1300 × 1800 × 2000 mm • Designed for composite prepreg curing applications • Heavy-duty industrial construction • Stainless steel internal chamber • High-efficiency hot air circulation system • Accurate programmable temperature control Lsdpfxsy Tvvze Ab Ashn • Multi-stage curing program capability • Controlled heating and cooling cycles • Uniform temperature distribution • 8 internal vacuum inlets installed inside the chamber • Vacuum pump included in the sale • Suitable for carbon fiber, fiberglass, prepreg, tooling, and composite components Applications: • Carbon fiber prepreg curing • Composite part manufacturing • Aerospace and motorsport components • Marine composite production • Tooling and mold post-curing • Drying and thermal treatment processes • Research & development and prototype manufacturing The oven is in very good working condition and can be inspected and tested on-site.

Year of construction: 2024, condition: new, functionality: fully functional, Forced-air curing oven Lhjdpfecutrlox Ab Asn Powder coating oven NEW SLS-90/O * D+t Through-feed oven, divisible Working dimensions: 1400 width x 2000 height x 6500 depth Overall dimensions: 1920 width x 2810 height x 6800 depth Power supply: Electric Rated power: 90 kW Voltage: 380V Frequency: 50-60Hz Door type: 2 doors on each side - through-feed oven Anti-explosion lock Warm-up time: 15-30 min. (180 °C) Homogeneity: < ± 3 °C at 180 °C Max: < ± 3 °C Maximum temperature: 230 °C Transport: optional Air circulation: Forced air Heaters: Interchangeable roof heating panels Airflow: Vertical Fan: Radially mounted on interchangeable panels Door: Double, two doors on two sides (through-feed oven) Divisible Motor power: 1.1 kW Capacity: 6480 L Warranty: 12 months GERMAN-SPEAKING CONTACT PERSONS IN GERMANY FEEL FREE TO INQUIRE Delivery time: approx. 12 to 16 weeks after order Shipping costs are calculated individually. We also offer systems tailored to your requirements. More information at Romer Germany Powder coating, electrostatic painting, Powder Coating, Powder painting, plastic powder, Peinture en poudre, thermoplastic, Verniciatura a polvere, Poederlakken, Порошковая окраска, Порошкове фарбування, powder coating booth powder coating system powder coating plant powder coating booth for powder coating surface technology powder gun powder guns curing oven powder coating oven industrial oven INDUSTRIAL OVEN, forced-air curing oven, powder coating oven

Condition: excellent (used), Year of construction: 2022, For sale: Romer powder coating line. Equipment manufactured in 2022, lightly used. It was used for coating armored doors. The powder coating line consists of: 1. Oven (doors on both sides, 5 coating tracks) Model: Romer SW Internal dimensions: 3000 x 1500 x 2200 mm The oven does not have a heating burner, it was previously used with a gas burner. A gas or electric burner can be installed if required. 2. Romer powder coating booth extraction wall Model: Romer KPO-3ZN 3. Conveyor system Overall dimensions: length 5900 mm x width 14000 mm, 2 trolleys with 5 tracks each. 4. Crossbeams with wheels (20 pcs.) Lodpfx Ajyzw Hwjb Ajhn Currently, the line is dismantled and ready for transport.

Condition: ready for operation (used), Year of construction: 2012, functionality: fully functional, machine/vehicle number: 7525SE-0949-FA, measuring range X-axis: 2,600 mm, number of axes: 7, TECHNICAL DETAILS Axes: 7 Measuring range: 2.6 m Accuracy Acceptance temperature: 20 °C Humidity during acceptance: 50 % Permissible single-point deviation: 0.028 mm Determined single-point deviation: 0.010 mm Maximum permissible volumetric length measuring deviation: ± 0.039 mm Determined volumetric length measuring deviation: -0.018 mm Scanner Manufacturer: Hexagon Model: CMS108 Integration: Calibrated within the measuring arm Note: Can be used on the measuring arm with appropriate scanning software Note: Scanning software not included in the scope of delivery MACHINE DETAILS Design: Portable measuring system Weight of measuring system including transport case: approx. 40 kg External dimensions of transport case for measuring arm: approx. 1,350 x 550 x 350 mm Dimensions of tripod: approx. 750 x 750 x 750 mm Weight of tripod: approx. 75 kg Dimensions of scanner case: approx. 600 x 450 x 220 mm Weight of scanner including carrying case: approx. 6 kg Notebook size: 17 inches Note: The measuring arm was relabeled before the last calibration. EQUIPMENT - Hexagon ROMER Absolute Arm RA-7525SE measuring arm, 7-axis - Mobility Pack FP2-1503-FA with wireless computer connection - Transport case for measuring arm - Magnetic base - Test bar, length 700 mm - Test sphere, diameter 25 mm - Probe box with 3 probes - Probe with ruby ball, diameter 6 mm - Probe with ruby ball, diameter 3 mm - Calibration sphere, diameter 15 mm - Dust cover - Complete cable set - Calibration certificate for measuring arm, notebook Dell M6600 - PowerInspect 11 software including hardware dongle - Hexagon RDS software - Brunson 231 roll stand, height-adjustable - Height adjustment range of tripod: approx. 700 to 1,100 mm - Scanner Hexagon CMS108 - Carrying case for scanner - Calibration certificate for scanner Note: PowerInspect 11 is exclusively for tactile measurements and cannot be linked with a scanner. Note for packaging request: €250 for special pallet with cardboard construction and tripod on a Euro pallet. Lhodpfx Aezv Rhujb Asn

Condition: new, Year of construction: 2024, functionality: fully functional, Powder coating plant Rim powder plant Romer Germany Lhsdpfx Abjq Ixcte Ajn

Condition: excellent (used), Year of construction: 2018, machine/vehicle number: 30111, functionality: fully functional, operating hours: 123 h, The OekoRona M is an electrostatic precipitator that significantly reduces fine dust emissions from automatic wood-fired heating systems with outputs between 300 kW and 3 MW. The precipitator has a modular design and can be installed in both new and existing systems. The mechanical cleaning system enables fully automatic operation of the precipitator and reduces maintenance to a minimum. OekoRona M facts: - for automatically fed wood-fired heating systems up to 3 MW - automatic, mechanical cleaning - tested separation efficiency - low operating costs - retrofittable - suitable for overpressure and underpressure operation - bypass - low energy consumption - various designs - flexible ash removal - operating optimization through remote maintenance Manufacturer: OekoSolve AG Type: OekoRona M Identification number: ORM-30111 Specified electrical power consumption: 1.65 kW Temperature class: T250 (according to the specified marking) Operating principle The flue gas flows through the tubes of the filter system, which are equipped with ionization electrodes. The high voltage electrically charges the fine dust particles, which then deposit on the inner surfaces of the separation tubes. The mechanical cleaning system automatically removes the deposited dust particles, which then fall into a lower collection container. An automatic discharge screw can transport the dust to an external collection container. Key technical features Feature Description Application area Automatic biomass-fired heating systems Boiler output range Approx. 300 kW to 3 MW for the product series Dust separation Electrostatic Cleaning Lhodpfe Aba Rgsx Ab Aon Automatic mechanical cleaning Flue gas temperature Maximum 250 °C Operating mode Suitable for overpressure and underpressure systems Bypass Integrated bypass Operation Touchscreen control Dust removal Collection container; screw discharge, depending on the design or optional Condensation protection Electrical or hydraulic heating, depending on the design Installation After the boiler in the boiler room

Condition: new, Year of construction: 2025, functionality: fully functional, machine/vehicle number: KAP1, air demand: 16,000 m³/h, power: 36 kW (48.95 HP), suction capacity: 16,000 m³/h, Equipment: cabin, Dielectric automatic powder booth KAP1 Price: PLN 492,693.30 + VAT Electrical and energy data • Voltage: 400 V (3P + N + PE) • Power connection: 36.34 kW • Pneumatic connection: 1" • Air pressure: min. 6 bar • Air quality: oil < 0.1 mg/m³, water vapor < 1.3 g/m³ • Air consumption: 1710 Nl/min (operation) • Compressor: SC-30 • Air tank: 1800 L Painting parameters • Painting speed: 1933 mm/min • Part dimensions: 800 x 1800 mm • Hanger height: 500 mm • Coating thickness: 100 µM • Gun array: vertical Technical data and configuration • Design: dielectric plastic • Passage dimensions: 1000 x 2400 mm • Air flow: 12348–16000 m³/h • Powder center: ProfiCenter CP02 • Manipulators: 2 pcs. • Guns: 8 automatic, 2 manual (ProfiSpray) • Part detection: yes (height, width) • Systems: cyclone separator, ProfiControl, beam pulling • ATEX: zone 22, II 3D Platforms and cabin body Ljdev Rpx Sepfx Ab Aehn • Platforms: entry, exit, stainless steel floor, anti-slip stairs • Housing: dielectric plastic, LED lighting, slots for manipulators Air knives and suction channel • Automatic floor cleaning • Suction channel with pneumatic flap Gun blow-off and control • Automatic blow-off guns • 10" touch panel, 50 programs, manipulator control, dust extractor, drive speed X-axis and part pulling system • Automatic gun setting • Part pulling: speed 570–2830 mm/min, 2 pullers The machine also includes: • ProfiSpray A applicator • PSS-1 controller • PM-1 guns • ProfiCenter CP-02 powder center • CK-D1400L cyclone dust extractor • MA1-180 manipulator and MX1-10 X-axis • OZ-12H dust extractor • ProfiControl 10" control • BP-H2000 W900 part measuring system

Year of construction: 2021, operating hours: 480 h, condition: like new (used), functionality: fully functional, Electrostatic separator (corona) - EBS-4-271200 - builded to extract the metals from the rejection of the plastic from electric cable process Including additional options: - 3 screw transporters; - 3 m3 input hopper; - mechanisms for changing material flow and stand for big bag for mix collection; - touch screen for control cabinet english / rusian language; - set of spare parts Designed for dry high-efficiency separation of materials, that are differ in their electric properties: - mixtures of plastics and metals, including shredded cables, into metal (copper, aluminium), and non-conducting material (plastic); - mixture of different materials, provided that one of the components has conducting properties (extraction oftextilecord from rubber crumb in the processing of used tires ); - shredded WEEE (including PCB’s) into metal (aluminium, copper, nickel, bronze, and other) and nonconducting materials (plastic, textolite, fiber-glass plastic, and other), and also for: - separations of non-metal raw material (feldspar, pegmatite, quartz sand); - enrichingofdroughconcentratesofores of rare metals (titan-zirconia, tantalum- niobic, tin-tungsten, monazite), ores of precious metals (gold, silver); - benefication of diamond ore. Ledjwcp I Aspfx Ab Aohn The equipment was purchased at the end of 2021 directly from the prestigious manufacturer PRODECOLOGIA, which also installed it in our factory. The equipment works perfectly and can be tested at any time with PVC plastic, from our Guidetti plant for electric cable recycling. Upon request, we can also provide installation + commissioning at the buyer's location. PRICE : 108 000 EURO- netto

Condition: as good as new (ex-display), Year of construction: 2025, operating hours: 1 h, Recirculating air oven, oil/gas-fired, model SOS 80 O Exhibition machine Technical data: Usable chamber dimensions: Width approx. 1200 mm, height approx. 1800 mm, depth approx. 3000 mm Lhsdpfx Absc Nbite Ajn Hanging rack available upon request Material: Internal housing: 0.8 mm steel sheet, tightly welded or riveted External housing: 0.8 mm steel sheet, base plate: 1.5 mm steel sheet Paint finish: RAL 1013, standard, powder-coated Insulation material: High-quality mineral wool Insulation thickness: Walls - 160 mm, ceiling: up to 240 mm, density 100 kg/m3 Performance data: Heating type: Oil, heating capacity: approx. 80 kW 1 oil burner with 80 kW capacity Total connection power: approx. 5.4 kW Temperature range: up to 200°C, continuously adjustable Subject to changes and errors in the technical data, information, and prices, as well as prior sale.

Year of construction: 2020, condition: new, ROMER® deals with the production of single technological equipment for powder coating plants as well as complete fully automatic turnkey coating plants. ROMER® provides heating solutions for the aero and automotive industries for the largest corporations in the world. We provide warranty and post-warranty service for devices sold by us with a full range of spare parts. the trawl applied to a poorly prepared surface will fall off or corrode after a short period of time. Lhsdpfxefz Ndye Ab Aen Ensuring the best coating is essentially good degreasing - which is the basis of any painting. The coating of a poorly degreased detail will fall off after a very short time. After degreasing, the next step is to tear down the outer coating of the detail, which improves paint adhesion, e.g. when bending sheet metal, and protection, e.g. with a phosphate layer, which in turn will prolong corrosion resistance. There are many solutions that solve the above issues. What is the most important thing in a powder coating shop? You probably don't have experience with the applicator. Nothing more wrong, even the best applicator will not help you if your oven has bad temperature distributions, in the place where the element is overheated, the paint will discolor and where not heated, the paint will fall off. First of all, the stove is the most important. Oil, gas or electric furnace? You don't know how to power your stove? how is cheaper what does this involve? What are the operating costs? We will try to answer your questions. Depending on the customer's requirements, transport systems can move on the floor or be suspended on poles. - For comfortable solutions for manual installations, we recommend suspended cross traverses (cross transport). - For automated systems, chain conveyors are most often used that do not stop and are a great solution for companies that focus on quality and repeatability of the process. - For companies that make different items at the same time and have e.g. several cabins with different colors, flexible solutions with the use of the power-and-free conveyor are used. This is the most expensive solution.

Year of construction: 2020, condition: new, ROMER® deals with the production of single technological equipment for powder coating plants as well as complete fully automatic turnkey coating plants. ROMER® provides heating solutions for the aero and automotive industries for the largest corporations in the world. We provide warranty and post-warranty service for devices sold by us with a full range of spare parts. the trawl applied to a poorly prepared surface will fall off or corrode after a short period of time. Ensuring the best coating is essentially good degreasing - which is the basis of any painting. The coating of a poorly degreased detail will fall off after a very short time. After degreasing, the next step is to tear down the outer coating of the detail, which improves paint adhesion, e.g. when bending sheet metal, and protection, e.g. with a phosphate layer, which in turn will prolong corrosion resistance. There are many solutions that solve the above issues. What is the most important thing in a powder coating shop? You probably don't have experience with the applicator. Nothing more wrong, even the best applicator will not help you if your oven has bad temperature distributions, in the place where the element is overheated, the paint will discolor and where not heated, the paint will fall off. First of all, the stove is the most important. Oil, gas or electric furnace? You don't know how to power your stove? how is cheaper what does this involve? What are the operating costs? Lhsdofz A H Dopfx Ab Aen We will try to answer your questions. Depending on the customer's requirements, transport systems can move on the floor or be suspended on poles. - For comfortable solutions for manual installations, we recommend suspended cross traverses (cross transport). - For automated systems, chain conveyors are most often used that do not stop and are a great solution for companies that focus on quality and repeatability of the process. - For companies that make different items at the same time and have e.g. several cabins with different colors, flexible solutions with the use of the power-and-free conveyor are used. This is the most expensive solution.

Year of construction: 2025, condition: new, Curing ovens shown in the photos can vary in price depending on size, configuration, and optional features. 💡📏⚙️ At ROMER, we manufacture both standard models and fully bespoke solutions, tailored to your process requirements. 🏭✅ Tell us your part size, line capacity, curing profile, and available space - and we will propose the best setup and the options that actually improve daily performance. 🔥🎯 🧠📡 Control and monitoring Live process control for temperature, time, airflow, and modes - with alarms and saved recipes for repeatable cycles. 🔁✅ 🔥🧩 Heating module Fast heat-up and stable temperature thanks to efficient heating elements and quick energy transfer. ⚡🌡️ 🌀💨 Air circulation Uniform airflow reduces temperature differences for consistent coating quality. 🎯✅ 🧱❄️ Insulation and design Smart chamber construction minimizes heat loss - faster reaching setpoint, lower consumption. ♻️📉 Ljdpfxjyg H Dzs Ab Ajhn 🛡️⚠️ Safety and certification Sensors, interlocks, and protection logic increase safety and reliability. 🔒👷 ⚡💰 High efficiency Optimized heat transfer and reduced losses mean real operating savings. 📉🔥 ⏰🤖 Automatic start Programmable schedule - automatic preheating before the shift for smoother production starts. ⏱️✅ 🚪🔒 Self-latching doors + intelligent chimney Prevents accidental opening, chimney activates only when needed for safer operation. 🧯✅ 🌿🔋 ECO mode Low-energy standby when idle - fuel consumption reduction up to 20% (depending on process). 🌱📉 👀💡 View and lighting Inspection without opening the door - fewer temperature drops, easier supervision. ✨👁️ 🛤️🔥 Guide rails + automatic hood Heat hood runs only during loading to reduce temperature loss, automatic rail infeed improves ergonomics and loading speed. 🙌⚙️ 🎛️🌡️ MULTI-ZONE HEAT Independent zone control for uniform curing of parts with different mass and geometry. 🧩✅ 🧠♨️ MTS system Heating elements mounted without thermal bridges - higher efficiency and faster time to set temperature. ⚡⏱️ 2-in-1 🧱↔️🧱 Split chamber Movable partition for two independent zones - drying and curing in one unit for maximum flexibility. 🚀🔁 🎚️🌀 VFD ventilation Variable fan speed based on chamber conditions - better control and lower electricity use. ⚙️💡

Year of construction: 2020, condition: new, ROMER® deals with the production of single technological equipment for powder coating plants as well as complete fully automatic turnkey coating plants. ROMER® provides heating solutions for the aero and automotive industries for the largest corporations in the world. Lhsdpfx Asflrc Sob Asn We provide warranty and post-warranty service for devices sold by us with a full range of spare parts. the trawl applied to a poorly prepared surface will fall off or corrode after a short period of time. Ensuring the best coating is essentially good degreasing - which is the basis of any painting. The coating of a poorly degreased detail will fall off after a very short time. After degreasing, the next step is to tear down the outer coating of the detail, which improves paint adhesion, e.g. when bending sheet metal, and protection, e.g. with a phosphate layer, which in turn will prolong corrosion resistance. There are many solutions that solve the above issues. What is the most important thing in a powder coating shop? You probably don't have experience with the applicator. Nothing more wrong, even the best applicator will not help you if your oven has bad temperature distributions, in the place where the element is overheated, the paint will discolor and where not heated, the paint will fall off. First of all, the stove is the most important. Oil, gas or electric furnace? You don't know how to power your stove? how is cheaper what does this involve? What are the operating costs? We will try to answer your questions. Depending on the customer's requirements, transport systems can move on the floor or be suspended on poles. - For comfortable solutions for manual installations, we recommend suspended cross traverses (cross transport). - For automated systems, chain conveyors are most often used that do not stop and are a great solution for companies that focus on quality and repeatability of the process. - For companies that make different items at the same time and have e.g. several cabins with different colors, flexible solutions with the use of the power-and-free conveyor are used. This is the most expensive solution.

Condition: excellent (used), Year of construction: 2001, functionality: fully functional, power: 0.14 kW (0.19 HP), input voltage: 230 V, type of input current: AC, volume flow: 1,890 m³/h, filter area: 7.9 m², noise level: 65 dB, actuation type: electric, total height: 575 mm, total length: 600 mm, total width: 590 mm, overall weight: 55 kg, Equipment: CE marking, documentation/manual, LTA electrostatic dust extraction system Intake on the right The intake nozzle can be screwed on as needed; currently, there is none, as it was previously mounted directly on the housing wall. Ljdpfx Aozqttcob Aehn In very good, fully functional condition, and naturally completely cleaned. Available for immediate delivery.

Year of construction: 2020, condition: new, Transport systems Depending on the customer's requirements, transport systems can move on the floor or be suspended on poles. - For comfortable solutions for manual installations, we recommend suspended cross traverses (cross transport). - For automated systems, chain conveyors are most often used that do not stop and are a great solution for companies that focus on quality and repeatability of the process. - For companies that make different items at once and have e.g. several cabins with different colors, flexible solutions with the use of the power-and-free conveyor are used. This is the most expensive solution. All installations are made to measure, depending on the customer's requirements. Continuous suspended chain transport systems are designed and manufactured to individual customer orders. In this system, it is also possible to make bottom conveyor systems on which details are placed, e.g. flower pots, rims (photo). ROMER also manufactures suspended transport systems. Crossbeams (cross transports) are designed and made for the needs of specific installations Lhsdpofz Dt Njfx Ab Aen The use of one photocell The use of one photocell in the space of the detail allows you to measure its length and, consequently, gives the option of switching on the guns when the detail appears in their range, and switching off the guns immediately after painting the detail. The photocell is standard equipment. Identification of details by means of special markers. Above the sling there are plates with identification holes. Based on them, the PLC controller in conjunction with the photocell recognizes the painted detail, turns the guns on and off in good time - thus saving energy and powder paint. Vertical shape detection. The use of light gates with horizontal detectors allows the PLC controller to analyze the shape of a detail vertically. The PLC controller counts the time in which the detail should appear in the gun space - thanks to this it is possible to selectively turn the guns on or off. Using light gates with multiple sensors horizontally and vertically. This solution allows precise measurement of workpiece dimensions, thanks to which it is also possible to control manipulators.

Year of construction: 2020, condition: new, Transport systems Depending on the customer's requirements, transport systems can move on the floor or be suspended on poles. - For comfortable solutions for manual installations, we recommend suspended cross traverses (cross transport). - For automated systems, chain conveyors are most often used that do not stop and are a great solution for companies that focus on quality and repeatability of the process. - For companies that make different items at once and have e.g. several cabins with different colors, flexible solutions with the use of the power-and-free conveyor are used. This is the most expensive solution. All installations are made to measure, depending on the customer's requirements. Continuous suspended chain transport systems are designed and manufactured to individual customer orders. In this system, it is also possible to make bottom conveyor systems on which details are placed, e.g. flower pots, rims (photo). ROMER also manufactures suspended transport systems. Crossbeams (cross transports) are designed and made for the needs of specific installations The use of one photocell The use of one photocell in the space of the detail allows you to measure its length and, consequently, gives the option of switching on the guns when the detail appears in their range, and switching off the guns immediately after painting the detail. The photocell is standard equipment. Identification of details by means of special markers. Above the sling there are plates with identification holes. Based on them, the PLC controller in conjunction with the photocell recognizes the painted detail, turns the guns on and off in good time - thus saving energy and powder paint. Vertical shape detection. The use of light gates with horizontal detectors allows the PLC controller to analyze the shape of a detail vertically. The PLC controller counts the time in which the detail should appear in the gun space - thanks to this it is possible to selectively turn the guns on or off. Using light gates with multiple sensors horizontally and vertically. Lsdpfx Abjfz Dubo Ashn This solution allows precise measurement of workpiece dimensions, thanks to which it is also possible to control manipulators.

Year of construction: 2020, condition: new, Transport systems Depending on the customer's requirements, transport systems can move on the floor or be suspended on poles. - For comfortable solutions for manual installations, we recommend suspended cross traverses (cross transport). - For automated systems, chain conveyors are most often used that do not stop and are a great solution for companies that focus on quality and repeatability of the process. - For companies that make different items at once and have e.g. several cabins with different colors, flexible solutions with the use of the power-and-free conveyor are used. This is the most expensive solution. Lhsdjfz I Edopfx Ab Aon All installations are made to measure, depending on the customer's requirements. Continuous suspended chain transport systems are designed and manufactured to individual customer orders. In this system, it is also possible to make bottom conveyor systems on which details are placed, e.g. flower pots, rims (photo). ROMER also manufactures suspended transport systems. Crossbeams (cross transports) are designed and made for the needs of specific installations The use of one photocell The use of one photocell in the space of the detail allows you to measure its length and, consequently, gives the option of switching on the guns when the detail appears in their range, and switching off the guns immediately after painting the detail. The photocell is standard equipment. Identification of details by means of special markers. Above the sling there are plates with identification holes. Based on them, the PLC controller in conjunction with the photocell recognizes the painted detail, turns the guns on and off in good time - thus saving energy and powder paint. Vertical shape detection. The use of light gates with horizontal detectors allows the PLC controller to analyze the shape of a detail vertically. The PLC controller counts the time in which the detail should appear in the gun space - thanks to this it is possible to selectively turn the guns on or off. Using light gates with multiple sensors horizontally and vertically. This solution allows precise measurement of workpiece dimensions, thanks to which it is also possible to control manipulators.

Year of construction: 2020, condition: new, Transport systems Depending on the customer's requirements, transport systems can move on the floor or be suspended on poles. - For comfortable solutions for manual installations, we recommend suspended cross traverses (cross transport). - For automated systems, chain conveyors are most often used that do not stop and are a great solution for companies that focus on quality and repeatability of the process. Lhsdpfx Abofz Nb Tj Aon - For companies that make different items at once and have e.g. several cabins with different colors, flexible solutions with the use of the power-and-free conveyor are used. This is the most expensive solution. All installations are made to measure, depending on the customer's requirements. Continuous suspended chain transport systems are designed and manufactured to individual customer orders. In this system, it is also possible to make bottom conveyor systems on which details are placed, e.g. flower pots, rims (photo). ROMER also manufactures suspended transport systems. Crossbeams (cross transports) are designed and made for the needs of specific installations The use of one photocell The use of one photocell in the space of the detail allows you to measure its length and, consequently, gives the option of switching on the guns when the detail appears in their range, and switching off the guns immediately after painting the detail. The photocell is standard equipment. Identification of details by means of special markers. Above the sling there are plates with identification holes. Based on them, the PLC controller in conjunction with the photocell recognizes the painted detail, turns the guns on and off in good time - thus saving energy and powder paint. Vertical shape detection. The use of light gates with horizontal detectors allows the PLC controller to analyze the shape of a detail vertically. The PLC controller counts the time in which the detail should appear in the gun space - thanks to this it is possible to selectively turn the guns on or off. Using light gates with multiple sensors horizontally and vertically. This solution allows precise measurement of workpiece dimensions, thanks to which it is also possible to control manipulators.