Used Retrofitted Gear Testing Machine Gm for sale (77,280)

Condition: excellent (used), Module range: 0,1 – 2 mm Centre distance range: 25 – 85 mm Vertical stroke of master gear slide: 40 mm Diameter of measured gear, max. (clamped on arbor): 120 mm Diameter of measured gear, max. (clamped between centers): 80 mm Maximum distance between centers for clamping of measured part: 200 mm Hfsdowkgr Iepfx Ab Uon Weight of measured gear, max.: 0,5 kg Measuring force adjustment, manually adjustable: 0 – 8 N Standard master gear arbor, diameter: 12,7 mm

Condition: used, SincoTec Type: Exciting Mot Resonance test bench POWER SWINGLY 20 kN The POWER SWINGLY BigTable resonance test bench is designed as a dual-mass vibrator. It consists of a vibration head, which is excited via an asynchronous motor with frequency control and an eccentric motor. Hfjdpozii Awefx Ab Uon The vibration head is located in the upper part of the machine and generates the dynamic amplitude. The vibration head is supported on the upper traverse via pre-tensioned coil springs and is guided centrally. The center load drive is located in the lower part of the machine and applies the static preload with the aid of a geared motor via a spindle drive. The test chamber is located above the mounting table and is bounded upwards by the adjustable traverse. The control of the test bench is carried out by the EXCITING MOT control system. The complete control electronics for the control system are housed in an industrial PC cabinet. The control cabinet is made of powder-coated steel sheet and meets protection class IP 50 according to EN 60529. Technical data: General data of the test bench: Overall height of the test bench 1840 to 2240 mm Height of the machine table 1030 mm Width of the test bench 800 mm Depth of the test bench 1500 mm Height of the test chamber max. 600 mm (without force sensor) Free column passage 550 mm Maximum force amplitude 10000 N Maximum total force ±20000 N Maximum stroke ±5 mm Test frequency 30 to 110 Hz Accuracy of the measuring sensors min. class 1 (according to DIN EN 10002-3) Weight of the test bench approx. 1880 kg Max. weight of the clamping device 150 kg General data of the control cabinet: Overall height of the control cabinet 1900 mm Height of the table top 1080 mm Width of the control cabinet 650 mm Depth of the control cabinet 700 mm Weight of the control cabinet 152 kg Color RAI 9006 (white aluminum), table top Midnight Conditions for the installation site: Space requirement 2.5 x 2.5 m Required ceiling height 2.8 m Floor load-bearing capacity 170 N/cm² Voltage supply 400 V / 50 Hz (right-rotating field) Connection plug CEE socket, 5-pole, 16 A Fuse 16 A Connection and environmental conditions Mains conditions: Voltage 400 V three-phase with PE conductor and protective earth, right-rotating field Voltage fluctuations < ± 10% Short-time voltage dips < 20 ms Limits for permanent interference Radio interference level A according to VDE0871 Frequency 50 Hz ± 1% Protective earth Ground resistance < 0.3 Ω Model: POWER SWINGLY MOT Condition: used Scope of supply: (See picture) (Changes and errors in the technical data are subject to change!) We will be happy to answer any further questions you may have by telephone.

Condition: used, INSTRON Spring Testing Machine / Universal Testing Machine SPRING SF1392-E1-L12-SPL Professional 100 kN testing machine for spring, compression, and material testing For sale is a used spring testing machine from the manufacturer INSTRON. The system was designed for highly precise spring, compression, and material testing. It is ideal for use in testing laboratories, research and development, quality assurance, and industrial manufacturing. Technical data: Manufacturer: INSTRON Type: SPRING Model: SF1392-E1-L12-SPL Serial number: SPRGK4348 Year of manufacture: 2007 Testing force: 100 kN Power supply: 240 V AC / 1~ / 50–60 Hz Mains current: 25 A Control voltage: 24 V AC / 50–60 Hz Max. ambient temperature: 40 °C Dimensions: Machine (W × D × H): approx. 1,307 × 757 × 2,392 mm Sliding door with 0 mm additional opening space Base Extension Model: 2910-061 Weights: Testing machine: approx. 1,145 kg Base Extension: approx. 96 kg 5800 Controller: approx. 31.8 kg Total weight: approx. 1,273 kg 5500 Controller: Dimensions (H × W × D): 650 × 280 × 570 mm Weight: approx. 31.8 kg Equipment: 100 kN testing frame Protective enclosure with sliding door Base Extension Model 2910-061 Instron 5500 Controller Operating console Industrial PC Monitor Keyboard Mouse Emergency stop system Testing platens / compression tools as shown in the pictures Technical documentation as shown in the pictures Application areas: Spring testing Compression testing Material testing Component testing Load testing Material testing Quality assurance Testing laboratory Research & Development Scope of delivery: Instron SPRING SF1392-E1-L12-SPL Base Extension Model 2910-061 Instron 5500 Controller Operating console Testing platens / compression tools as shown in the pictures Machine accessories as shown in the pictures Technical documentation as shown in the pictures Important note: To operate the system, the original Instron testing software including a valid software license is required. The software and the software license are not included in this offer. According to the manufacturer, a corresponding retrofit is required for recommissioning. A functional test could not be carried out due to the missing software. The sale is therefore preferably aimed at specialist companies for recommissioning or upgrading. Condition: Used Optical condition according to the pictures. Normal signs of wear and tear are present. The workbench shown in the photos is not part of the sale. The operating console and the machine accessories shown are included in the scope of delivery. Transport information: Original shipping dimensions according to the manufacturer: 2,795 × 1,600 × 1,295 mm (L × W × H) Shipping weight according to the manufacturer: approx. 1,565 kg Loading with a forklift is possible. Shipping via a freight forwarder is possible. Hfjdpfezlp Ixjx Ab Ujn Subject to changes, errors and prior sale. We will gladly answer any further questions by telephone or email.

Condition: ready for operation (used), The Klingelnberg PSR 500 U worm gear testing machine was designed as a universal machine for the flexible testing of worm gears and is used by manufacturers of gear and transmission technologies for the single-flanking rolling test process for worm gear sets (EFWP). Technical data: Max. worm gear diameter: 500 mm Max. spindle length: 500 mm Max. spindle diameter: 200 mm Center distance: 0 ... 400 mm Max. measuring speed: 60 rpm Braking torque: 2.5 Nm Max. worm gear weight: 150 kg Max. spindle weight: 50 kg Table diameter: 300 mm Machine weight: 800 kg Dimensions: 1500 x 1500 x 1600 mm The following parameters can be measured here: Hjdjzxghvjpfx Ab Usfn • Flank deviations Fi', fi', fl', fk' • Flank clearance, runout, roundness (option) • Contact pattern with digital camera • Pitch deviation • FFT analysis, spectrum *Image shows the machine in its current condition as a retrofit/modernized unit. *Further information about the machine is available upon request.

Condition: good (used), workpiece diameter between centers: 2,286 mm, The No. 61 Angular Hypoid Tester is designed to test large bevel and hypoid gears up to 90" diameter and with shaft angles from 0 - 135 degrees. Spur, helical and internal gears can also be accommodated. The drive or pinion spindle can be rotated in either direction at a recommended spindle speed of 600 RPM. It is mounted in a head which is vertically adjustable on a column, so that the spindle can be offset either above or below the center line of the gear spindle for testing hypoid gears. The pinion head column is adjustable angularly in a horizontal plane to permit testing of gears of any shaft angle from 0 - 135 degrees. Specifications: Centerline of Drive Spindle to Nose of Brake Spindle (90 degrees shaft angle and without face plate): 38-1/2" Max. / 7-5/8" Min. Centerline of Brake Spindle to Nose of Drive Spindle (90 degrees shaft angle and without face plate): 60" Max. / 10" Min. Centerline of Brake Spindle to Nose of Drive Spindle (90 degrees shaft angle and with 54" face plate): 60" Max. / 28" Min. Centerline of Brake Spindle to Centerline of Drive Spindle (For Spur Gears): 56" Max. / 6" Min. Distance Between Nose of Brake Spindle and Nose of Drive Spindle (for spur gears): 36-1/2" Max. / 0" Min. Offset of Drive Spindle Either Above or Below Centerline of Brake Spindle: 10" Hedpfxjrtrzds Ab Ujfn Range of Shaft Angles: 0 - 360 Degrees Maximum Diameter of Gear: 90" Diameter of Face Plate: 54" Outboard Bearing: 3" Diameter Hole Spindles: RPM of Drive Spindle Pulley Set No. 1: 100 - 400 RPM of Drive Spindle Pulley Set No. 2: 250 - 600 Diameter of Taper Hole (large end): 6" Taper Per Foot: 3/4" Depth of Taper: 8" Hole Through Spindle: 5-1/2" Net Weight of Machine: 20,000# Net Weight of Machine W/Outboard Support and Bed Plate: 24,000#

Condition: used, Year of construction: 1980, max. wheel diameter 2500 mm gear width 0 mm max. module 34 min. module 1 total power requirement ca. 15 kW weight of the machine ca. 15 t dimensions of the machine ca. 4,20 x 2,00 x 2,90 m Hedpfxst Hw Aaj Ab Usfn Extra große ZR-Prüfmaschine, Gegenhalter

Condition: used, Year of construction: 1980, max. wheel diameter 400 mm gear width NA mm max. module 5 min. module total power requirement kW weight of the machine ca. t dimensions of the machine ca. m Hsdjt Hw Ebepfx Ab Uofn Manual Two Flank Gear Tester

Condition: excellent (used), Year of construction: 2017, XYZ 2000 Turret Milling Machine (2017) (Ex College) 3 Axis Newhall DRO (X, Y & Knee) Spindle Taper R8 Spindle speeds to 500 – 4200 rev/min Table Size 1270 x 254mm Table Travel: X - 812mm Y - 406mm Knee Travel: Z - 406mm Hfsdpfx Asxxb Rrsb Uon Quill Travel Z - 127mm For sale with Jet Machinery Ltd Jet Machinery Stock No: #79047 Machine Serial Number: 12907 Cost: £9,950.00 + VAT Whilst every effort has been made to ensure that the above information is accurate it is not guaranteed. We advise prospective purchasers to check any vital details. Health and Safety At Work Act 1974: It is not reasonably practical for ourselves as suppliers to ensure that for your application the goods comply with requirements of the Act with respect to guarding etc. Prospective purchasers should ensure that a guarding specialist inspect the goods prior to use.

Condition: refurbished (used), functionality: fully functional, The Klingelnberg PKE 300 H (PSKE 900) bevel gear testing machine was designed as a universal machine for the flexible machining of gears and is used for single flank rolling tests on bevel gears with evaluation Picture shows machine in actual condition as retrofit / modernized. Performance description: Wheel diameter: 450 (300) mm Axle angle: 90 degrees Hypoid: +/- 60 mm Space requirement approx.: 1.4 x 0.8 x 1.5 mm Machine weight approx.: 1,100 kg Hfedetncnhjpfx Ab Uon Further information on possible options, current purchase price on request. *Information, dates are non-binding, subject to prior sale

Condition: used, Year of construction: 1975, max. wheel diameter 160 - 1.600 mm Hjdpfx Abot Hwpte Ujfn gear width 250 mm max. module 20 min. module 1,5 total power requirement 1 kW weight of the machine ca. 3 t dimensions of the machine ca. m

Condition: good (used), Year of construction: 1992, weight 5,5 t Table tip diameter: 35 mm Tip height above table: 75 mm Counterholder tip diameter: 50 mm Counterholder tip stroke: 40 mm Minimum center-to-center distance: 20 mm Minimum measuring height above table: 50 mm Maximum measuring height above table: 800 mm Table diameter: 500 mm Base circle diameter: 0–1000 mm Maximum rolling path: ±115 mm Maximum workpiece weight: 2000 kg X-axis: 230 mm Y-axis: 530 mm Z-axis: 750 mm Max. workpiece diameter: 1000 mm Software for new PCs: Windows 11 Bevel gear software, if desired, available only on Metrotek installations Additional information: - Machine calibrated according to DAKKS on November 19, 2017 Hodszidz Ispfx Ab Ujfn

Condition: used, Year of construction: 2006, workpiece diameter 5 - 1.000 mm module range 0,2 - 25 Hjdpfoyvvlbox Ab Uefn helix angle < 90 ° Control Wenzel GearTec faceplate diameter 750 mm x-axis 1.200 mm y-axis 550 mm z-axis 1.000 mm total power requirement 6,5 kW weight of the machine ca. 11 t dimensions of the machine ca. 3,30 x 3,15 x 2,70 m Software: BMain, FPDFPPostAction, GrafTool, TAlign, TAnalyse, TApplication, TCali, TCut_INPUT, TCut_MEAS_EVAL, TGear_INPUT, TGear_MEAS_EVAL, THob_INPUT, THob_MEAS_EVAL, TMesblatt, TPlot, TRoot_INPUT, TShaft_INPUT, TShaft_MEAS_EVAL, TStat, TStylus, WMI, wingeco.

Condition: used, Zwick   Type: BZ1.0 / TH1S   Zwick table-top testing machine   Zwick with a maximum force of 1.0 kN.   Crosshead travel: 1150 mm. Testing speed: 0.1 ... 1800 mm/min   Scope of supply: (See images)   (Changes and errors in the technical data are subject to change!)   We would be happy to answer any further questions you may have by phone. Hfedezdryzspfx Ab Uon

Condition: used, Zwick Type: BZ2.5/TN1S Zwick table-top testing machine, tensile strength measuring machine Application area: Wide range of applications, from testing plastics and elastomers to testing paper, textiles, foam, and wire, as well as component testing. Load frame: Max. test force FN in tension/compression direction: 2.5 kN Height (h1): approx. 770 mm Width with electronics unit: 320 mm Depth with electronics unit: 414 mm Hodjzdry Ijpfx Ab Uefn Height of the working area h min ... h max: Travel carriage angle mounted upwards: 227 ... 573 mm Travel carriage angle mounted rotated by 180°: 57 ... 403 mm (each without connecting pin) Connection values: Electrical connection: 115/230 V, 4/2 A, 1-phase/PE/N Power consumption: 0.4 kVA Mains frequency: 50/60 Hz 2.5 kN Condition: used Scope of delivery: (See image) (Changes and errors in the technical data are subject to change!) We will be happy to answer any further questions you may have by phone.

Condition: excellent (used), Year of construction: 1972, functionality: fully functional, For sale: this gear hobbing machine. It is connected and can be tested. Comes with numerous accessories. Hfjdpfjxwlthox Ab Ujn Technical specifications: Max. gear diameter: 7100 mm Gear width: 1500 mm Max. module: 45 Table diameter: 4000 mm Hob diameter x width: 400 x 500 mm Max. helix angle: 45 degrees Cutter diameter: 500 mm Cutter speed: 9–63 rpm Total power consumption: 47 hp Machine weight: 160,000 kg The machine has hydraulic workpiece balancing. A video of the machine can be sent via WhatsApp.

Condition: used, Year of construction: 2007, max. wheel diameter 500 mm Hypoid adjustment ±70 mm axial cross angle 90 ° Distance Y- 150 - 350 mm Distance Z-axis 120 - 340 mm Hjdpfxjukitxo Ab Uefn turning speed range - stepless 0 - 5000 U/min max. torque on the spindle 57 Nm Cone 99,2 mm Pull-in force Tool clamping 23000 N Braking torque max. 93 Nm total connected load 20 kVA total power requirement 15 kW weight of the machine ca. 6 t dimensions of the machine ca. 2,35 x 2,24 x 2,5 m

Condition: used, Zwick / Roell Type: Z020 Allround-Line BT1-FR020TN.A50 Zwick / Roell Material Testing Machine, 20 kN, Tensile & Compression Testing, testXpert III For sale is a high-quality Zwick / Roell material testing machine for professional tensile and compression testing of materials and components. The machine is suitable for metals, plastics, rubber, and many other materials and is typically used in laboratories, quality assurance, research, and education. The machine is controlled via a PC with Zwick/Roell testXpert III software (storage medium and documentation available). Technical Data: Nominal testing force: 20 kN Testing direction: Tensile & Compression Power connection: 230 V / 50–60 Hz / 1-phase Power consumption: approx. 2.1 kVA Weight: approx. 150–180 kg Dimensions: approx. 856 × 650 × 1,545–2,114 mm Technical Data (from documents & nameplate) Mechanics / Testing Nominal force: 20 kN Testing direction: Tensile & Compression Max. testing frequency: 0.5 Hz Crosshead: servo-electric Positioning accuracy: < 1 µm Speed range: 0.0005 – 1,000 mm/min Dimensions & Weight Overall height: approx. 1,545 – 2,114 mm (depending on the crosshead position) Overall width: approx. 856 mm Overall depth: approx. 650 mm Working space width: 440 mm Weight: approx. 150 kg (basic unit) approx. 180 kg with typical equipment Electrical Data Power connection: 230 V AC Phases: 1-phase (1PH, N, PE) Mains frequency: 50 / 60 Hz Current consumption: approx. 8–10 A Hfsdpfjzimgtox Ab Uen Power consumption: approx. 2.1 kVA Socket: Schuko (CEE 7) Measuring & Control Electronics Internal measurement value acquisition: 500 Hz Data transmission to PC: 10–100 Hz adjustable Interface: RS232 (COM) Protection class for electronics housing: IP32 Important note: “The table shown in the photos is not included in the sale.” Condition: used Scope of supply: (See picture) Zwick / Roell material testing machine (20 kN) Electronics unit PC workstation (monitor, PC condition see pictures) 2 measuring modules (Delock units) Zwick/Roell testXpert III software (storage medium) Original operating and technical documentation Various connection and linking cables (Changes and errors in the technical data are subject to change!) We will gladly answer any further questions you may have by phone.

Condition: used, Zwick / Roell Type: BDO-FB0.5TH Zwick / Roell tensile testing machine, table-top testing machine Material testing machine BDO-FB0.5TH Testing load in tensile/compressive direction: 500 N Height: 1565 mm, Width: 292 mm, Depth: 469 mm Hfedpfszdr Hnox Ab Uon Width of test area: infinite Test area depth: 100 mm Max. working distance without accessories: 1266 mm PC or printer interface: RS 232 Required PC connection (for PC operation): COM 1 Power data: 115/230 V (PH, N, PE) Rated power: 0.4 kVA Mains frequency: 50/60 Hz Weight: 47 kg Condition: used Scope of supply: (autosampler as shown in the picture) (Subject to changes and errors in the technical data; details are subject to change!) We will be happy to answer any further questions you may have by phone.

Condition: used, Year of construction: 2001, max. wheel diameter 400/500 mm CNC-Control GE FANUC Series 160i-M pinion diameter - max. 400 mm crown gear diamter max. 500 mm x-axis +/- 70 mm y-axis 200 mm z-axis 200 mm axis angle 90 Grad speeds: R T min rated current 30 kVA Hodsvxwxcopfx Ab Uofn weight of the machine ca. 6,2 t dimensions of the machine ca. 3,2 x 2,5 x 2,3 m

Condition: used, Zwick / Roell Material Testing Machine / Universal Testing Machine Zwick / Roell Z020 Allround-Line BT2-FR020TNW.A50 20 kN material testing machine for tensile and compression testing with testControl II & testXpert V3.5 For sale is a used material testing machine from the manufacturer Zwick / Roell. The machine is suitable for tensile and compression tests on metals, plastics, elastomers, composite materials, and numerous other materials in the laboratory, quality assurance, research and development. Technical data: Manufacturer: Zwick / Roell Model series: Z020 Allround-Line Type: BT2-FR020TNW.A50 Testing force: 20 kN Testing direction: Tensile & Compression Testing space height: 1000 mm Crosshead speed: 0.0005–1000 mm/min Power connection: 230 V / 50–60 Hz Power consumption: 8 A Electronics: testControl II Software: Zwick / Roell testXpert V3.5 Equipment: Servo-electric material testing machine testControl II control system Industrial PC with installed testXpert V3.5 software 20 kN Xforce P load cell 2.5 kN Xforce P load cell Testing table Test fixture Various connection and cable sets Accessories as shown in the pictures Dimensions and weight: Machine dimensions (approx.): 1244 × 690 × 1324 mm (W × D × H) Weight: approx. 212 kg Application areas: Tensile testing Compression testing Material testing Quality assurance Research & Development Hfedpfxjzra Rqs Ab Uon Testing laboratory Education and training Scope of supply: 1 × Zwick / Roell Z020 Allround-Line material testing machine testControl II control system Industrial PC with installed testXpert V3.5 software 20 kN Xforce P load cell 2.5 kN Xforce P load cell Connection and cable sets Further accessories as shown in the pictures Condition: Used Visual condition as shown in the pictures Functional scope as shown in the pictures Nameplates are present The table, monitor, keyboard, and mouse shown in the photos, as well as any other items not explicitly mentioned, are not part of the sale. Shipping or freight forwarding possible. Subject to change, errors and prior sale. We will be happy to answer any further questions by telephone.

Condition: used, Zwick Type: BT1-FR050TH.A1K 50 kN Material testing machine Zwick/Roell BT1-FR050TH.A1K material testing machine – Precise strain gauge tests Hjdpfxozii Uge Ab Uefn Note: No PC included!! Highlights: Testing force: 50 kN (tensile / compressive) High-precision TC-MODCSCC module for strain gauge load cells (4- & 6-conductor) Measuring range: 0.2 – 165 % nominal value, measurement value acquisition up to 500 Hz Maximum resolution: up to 297,000 points (at 50 Hz) Positioning repeatability: ±10 µm Crosshead speed: 0.0005 – 600 mm/min Robust design, compact dimensions: 1,814–2,688 mm height, 936 mm width, 722 mm depth Low noise: 59 dB(A), ambient temperature +10 to +35 °C, humidity 20–90 % Special features: Ideal for research, development, or industrial material testing Dimensions & weight: Load frame: Testing force (tensile/compressive): 50 kN Load frame height: 1,714 mm Overall height: 1,814 – 2,688 mm Load frame width: 760 mm Overall width: 936 mm Load frame depth: 477 mm Overall depth: 722 mm Weight: With electronics unit: 230 kg With typical attachments: approx. 300 kg Condition: used Scope of delivery: (See picture) ZwickRoell BT1-FR050TH.A1K testing machine Operating manual (Changes and errors in the technical data are subject to change!) We will be happy to answer any further questions you may have by telephone.

Condition: excellent (used), Year of construction: 2021, XYZ RMX 3500 3 Axis CNC Bed Milling Machine ProtoTRAK RMX Control YOM 2021 Spindle: 5HP – Programmable 40 – 5000rpm 2 Ranges 40 – 600 & 300 – 5000rpm ISO40 Quill Dia 105mm Table: 1370 x 355mm 4 0ff T Slots T Slot size 15.9mm Max load 600kgs Travel: X – 787mm Y – 508mm Head Vertical (Z) – 500mm Quill (Z) 127mm Dims without travel – 1905 x 2069 x 2225mm Dim with travel – 2758 x 2869 x 2490mm Hodpfxex D Tbms Ab Usfn Weight 2430Kgs Power Requirements 22A Air Requirements 6bar YOM 2021 For Sale with Jet Machinery Ltd Jet Machinery Stock Number: #78900 Machine Serial Number: RM310097 £35,000.00 + VAT Whilst every effort has been made to ensure that the above information is accurate it is not guaranteed. We advise prospective purchasers to check any vital details. Health and Safety At Work Act 1974: It is not reasonably practical for ourselves as suppliers to ensure that for your application the goods comply with requirements of the Act with respect to guarding etc. Prospective purchasers should ensure that a guarding specialist inspect the goods prior to use.

Condition: refurbished (used), Year of construction: 2027, functionality: fully functional, rotary table diameter: 590 mm, position of the milling head: Schwenkbar (50°), table diameter: 590 mm, total length: 5,100 mm, gear diameter: 750 mm, total height: 3,240 mm, total width: 4,000 mm, input frequency: 50 Hz, type of input current: three-phase, milling length: 250 mm, spindle speed (max.): 360 rpm, spindle speed (min.): 36 rpm, travel distance X-axis: 450 mm, travel distance Y-axis: 200 mm, travel distance Z-axis: 600 mm, overall weight: 12,000 kg, rotational speed (max.): 360 rpm, rotational speed (min.): 18 rpm, distance table to spindle center: 500 mm, tool diameter: 215 mm, controller manufacturer: Siemens Sinumerik ONE, drive type: Sinamics S120, control type: CNC control, Equipment: documentation/manual, rotational speed infinitely variable, The Liebherr LC 752 is one of the most widely produced hobbing machines in its class: rigid bed, robust milling head, and proven performance in the gear, drive, and supplier industries for spur and helical gears and shafts up to 750 mm in diameter. Serwema Retrofit Solutions, Chemnitz, completely overhauls the machine and delivers it with Siemens Sinumerik ONE, the latest generation of control system with full availability of spare parts and support. Proven Liebherr kinematics, new electrical system, new drives, new safety technology: you get the performance of a new machine at a fraction of the price, with an eight-month delivery time, and acceptance testing is carried out in Chemnitz together with you. The machine mills spur and helical gears as well as shafts up to module 10, and in a reinforced version up to module 14. With an axis travel of 600 mm between the milling head axis and the table surface, even long pinion shafts can be securely clamped. The milling head swivels by ±50°, the milling head speed ranges from 36 to 360 rpm, the table rotates at up to 18 rpm for small numbers of teeth, and the tangential travel of 200 mm utilizes the full milling head length for long tool life. Hfjdpfx Aez Et N Rsb Ujn Technical data: max. workpiece diameter 750 mm, table diameter 590 mm, distance between milling head axis and table axis 50–500 mm, distance between milling head axis and table surface 175–775 mm, max. module 10/14, max. milling head diameter 215 mm, max. milling head length 250 mm, tangential travel 200 mm, milling head speed 36–360 rpm, max. table speed 18 rpm, swivel angle ±50°. Installation dimensions approx. 5.1 × 4.0 × 3.24 m, weight approx. 12 t. The machine is delivered with a new Siemens Sinumerik ONE control system and Sinamics S120 drives in a climate-controlled control cabinet manufactured in-house. The user-friendly interface makes setup and programming possible without in-depth G-code knowledge. Geometric acceptance is carried out according to the manufacturer's standard or DIN, with a protocol. The scope of delivery also includes the complete machine enclosure with safety technology according to the latest standards, a new coat of paint in RAL 5015/7035, a magnetic chip conveyor, circulating and loss lubrication, a hydraulic unit, a coolant system, and the operating manual.

Condition: used, Zwick/Roell Zwick/Roell ProLine Universal Testing Machine Z010 TN – 10 kN, Type: BT1-FB010TN.D30 For sale is a professional material testing machine from Zwick/Roell, suitable for tensile and compression tests up to 10 kN. Hjdpfx Aezizrkjb Uefn The machine comes from an industrial setting and has been professionally operated. General Data: Manufacturer: Zwick GmbH & Co. KG, Ulm Rated force: 10 kN Type of test: Tensile and compression test Technical Performance Data: Crosshead speed: 0.001 – 1,000 mm/min Speed accuracy: 0.01% of Vnenn (nominal speed) Displacement resolution: 0.038 µm Positioning repeatability: < 2.0 µm Maximum test frequency: 0.5 Hz Data acquisition rate: 500 Hz Data transfer to PC: 10–100 Hz Force measurement according to ISO 7500-1 Dimensions & Weight: Height with leveling elements: approx. 1,331 mm Width with electronics: approx. 930 mm Depth with electronics: approx. 437 mm Working space width: 440 mm Working space height (bottom): 1,050 mm Weight with typical components: approx. 160 kg Electrical Data: Adjustable mains voltage: 100–250 V Mains frequency: 50 / 60 Hz Power consumption: 800 VA Current consumption at 230 V: approx. 3.4 A Fuse rating: ≤ 16 A Connection: 1L / PE / N Documented test and calibration records: 18.09.2017 Machine BT1-FB010TN.D30 testXpert II Version 3.2 tC-PC System Temperature during testing: 23.3 °C Displacement measurement system: Incremental encoder (rotary) Force sensor installed 29.01.2014 Force sensor: Xforce HP Module: DCSC Calibration at Zwick Ulm 28.08.2013 Force sensor: Xforce P Module: DCSC Rotation before test series: 120° testXpert control system Documented service and calibration records are available. Software & Control: Software: testXpert® II Documented version: V3.2 Installation documentation from version 2.2 Documentation status: March 2010 PC control: tC-PC Interfaces: RS232 / Ethernet Note: testXpert II is a professional industrial testing software. Installed Modules & Components DCSC measuring module Force sensor Xforce P / Xforce HP Incremental encoder (rotary displacement measurement system) ISO 7500-1 compliant force measurement Installed under the traverse Important Note: “The table shown in the photos is not part of the sale.” Condition: used Scope of delivery: Material testing machine BT1-FB010TN.D30 PC with monitor Force sensor DCSC module Specimens / Grips Adapters and holders Tools Documentation folder with documents Scope of delivery as shown in the pictures. (Changes and errors in the technical data are subject to change!) We will be happy to answer any further questions you may have by telephone.

Condition: used, Zwick / Roell Universal testing machine / Material testing machine Zwick / Roell ProLine Z005 Universal Testing Machine 5 kN testing machine for tensile, compression, and material testing For sale is a used universal testing machine from the manufacturer Zwick / Roell. The machine is suitable for tensile tests, compression tests, material testing, component testing, quality assurance, research and development, and laboratory applications. Technical data Manufacturer: Zwick / Roell Type: ProLine Z005 / 5 kN ProLine Type of device: Universal testing machine / Material testing machine Year of manufacture: 2016 Made in Germany Maximum testing force: 5 kN Load cell: Zwick Xforce P Rated force of load cell: 5 kN Start of measurement, accuracy class 1: 20 N Start of measurement, accuracy class 0.5: 100 N Nominal measuring range: 0.06 mm Machine dimensions: approx. 917 x 439 x 1331 mm (W x D x H) Frame width: approx. 720 mm Installation width of frame: approx. 770 mm Testing space width: approx. 440 mm Machine weight: approx. 200 kg Weight of load cell: approx. 0.65 kg Mains connection: 230 V Frequency: 50 / 60 Hz Current consumption: 3.5 A Connection: 1L / PE / N Measuring module: DCSC Measuring range: 0.2 % to 165 % of the nominal measuring value Measurement value acquisition rate: max. 10 kHz Measuring input: Differential input Sensor supply: 10 V DC Strain gauge bridge resistance: 175 to 1200 Ω Connection type: 4- and 6-conductor technology Nominal sensitivity: 2 mV/V Connection thread for load cell: M28 x 1.5 Connection bolt: Ø 20 mm Dowel pin: Ø 8 mm Degree of protection of load cell: IP54 Load cell Type: Xforce P Rated force: 5 kN Working force max.: 150 % of Fnom Limit force: 150 % of Fnom Breaking force: 300 % of Fnom Limit transverse force: 100 % of Fnom Component height: 95 mm Installation dimension: approx. 72 mm Installation height: approx. 61 mm Diameter: 54 mm Equipment Zwick / Roell ProLine testing frame Xforce P 5 kN load cell DCSC measuring module Electronic force measurement Machine electronics on the side of the load frame PC system / testing software as shown in the pictures Accessories as shown in the pictures Application areas Tensile testing Compression testing Material testing Material characterization Quality assurance Incoming goods inspection Research and development Laboratory applications Condition Used Optical condition as shown in the pictures Scope of delivery 1x Zwick / Roell ProLine Z005 Universal Testing Machine 1x Xforce P 5 kN Load Cell 1x DCSC Measuring Module PC system / Software as shown in the pictures Accessories as shown in the pictures The table shown in the photos, as well as any other items not explicitly mentioned, are not included in the sale. Shipping or forwarding possible. Hjdpfjzfy Ivex Ab Usfn Subject to changes, errors and prior sale. We will gladly answer any further questions by telephone.