Used Forst Hard Broaching Machine for sale (66,227)

Year of construction: 1992, condition: used, machine/vehicle number: 148, Broaching Machine – Vertical Hard Broaching Machine Lodpodnk T Aofx Ab Aoru Manufacturer: Forst Typ: RISZ 6,3 x 1000 x 320 Machine number: 148 Year of manufacturing: 1992 Force max.: 80 kN Stroke max.: 1.000 mm Weight: approx. 10 Tons (Machine+Control Cabinet+Hydraulic aggregate)

Condition: used, functionality: fully functional, Year of construction: 2019, machine/vehicle number: 53, overall weight: 38,500 kg, input voltage: 400 V, input current: 355 A, input frequency: 50 Hz, broaching speed: 12 m/min, workpiece diameter (max.): 225 mm, total length: 7,100 mm, total width: 11,560 mm, total height: 6,000 mm, Forst RISH 60 x 2125 x 630 – Vertical internal broaching machine Used Forst broaching machine for internal broaching of ring gear workpieces. The machine features a lifting table and a servo-electric broaching drive; the broach pitch is set via the NC program. Machining is performed individually or in pairs, depending on the workpiece. Identification Ljdpfxsz Hq Ake Ab Aoru Manufacturer: Forst Technologie GmbH & Co. KG Type: RISH 60 x 2125 x 630 Factory number: 53 Forst order number: M233202 Reference / Inventory number: 351024 Year of manufacture: 2019 (according to machine data sheet) Technical data according to machine documentation - Maximum tensile force: 600 kN - Maximum stroke: 2,125 mm - Maximum cutting speed: 12 m/min - Return stroke speed: 20 m/min - Maximum workpiece diameter: 225 mm - Maximum workpiece height: 50 mm - Maximum tool diameter: 200 mm - Tool shank diameter: 80 mm - Tool tip diameter: 75 mm - Overall dimensions (L x W x H): approx. 7,100 x 11,560 x 6,000 mm - Total weight of the machine: approx. 38,500 kg - Weight of the base machine: approx. 34,500 kg - Electrical connection: 400 V, 3 phases, 50 Hz - Rated current according to nameplate: 355 A Documented features - Siemens SINUMERIK 840D sl / S7-300 - Operator panel OP012 and hand-held operating unit HT8 - SKF roller screw drive and linear guides - Hydraulic workpiece clamping - Coolant system with high/low pressure supply and 1,800-liter tank - Chip conveyor and chip centrifuge - Oil mist separator and central lubrication system Operating manual and technical documentation are available. The data and features listed describe the documented machine condition. The actual scope of supply should be agreed upon before finalization. The suitability for other workpieces requires a technical assessment and, if necessary, adapted tools and fixtures. Used machine, operated without malfunctions until disassembly. Price on request.

Condition: not inspected (used), Forst RF 16 internal broaching machine Lredpfxshu E N Ds Ab Aeu -WKG 1371- Technical data: Manufacturer: Forst Type: RF 16 Max. Tractive force: 16t Max. Stroke: 1200mm Max. Cutting speed: 5,6m/min Max. Workpiece diameter: Ø 700mm Max. Tool diameter: Ø 120mm Workpiece seat: Ø 70mm Note: control valve missing

Condition: ready for operation (used), Year of construction: 2022, Hongming HM-950 continuous roller pressing and flattening machine, suitable for the production of hard covers, book covers, folders, presentation materials, rigid boxes, and other glued cardboard or paper products. The machine continuously feeds the material through a large pressure roller via a conveyor belt. This ensures an even pressing result, improves adhesion between the glued layers, and helps to remove trapped air bubbles and irregularities. The pressure and working height can be adjusted manually on both sides of the machine. Technical specifications: * Manufacturer: Hongming * Model: HM-950 * Machine type: Roller pressing and flattening machine * Year of manufacture: June 2022 * Working width: Approx. 950 mm * Serial number: J01010089-0026 * Voltage: 380 V * Frequency: 50 Hz * Current: 3.4 A Ljdpfxszq Tz Ts Ab Aeru * Motor power: 0.75 kW * Power supply: 3-phase * CE marked Suitable for: * Hard-cover production * Bookbinding and book-cover production * Rigid-box and luxury-box components * Greyboard with glued covering paper * Folders and presentation covers * Cardboard and paper converting * Pressing and smoothing of glued materials Condition and equipment: The machine is in clean overall condition and appears complete. It is equipped with a continuous conveyor belt and a large covered pressure roller. The original English-language operating manual is included. Inspection is possible by appointment.

Year of construction: 2001, condition: used, machine/vehicle number: 29, Manufacturer FORST Machinenumber: 29 Year of Manufacturing: 2001 Force max.: 63 kN Stroke max.: 1000 mm Weight: 7 tons (machine + control cabinet + coolant system) Broaching Stations: 1 Cycle Time: 28 sec. Cutting Speed max.: 8 m/sec back hub: 16 m/sec Ljdpfx Asdnk Ukjb Ajru Shank Ø: 32 mm Endfitting Ø: 25 mm

Year of construction: 1963, condition: used, machine/vehicle number: 18135, Broaching Machine – Horizontal Manufacturer: Forst Typ: RIW 100/2200 Force: 100 Tons Stroke: 2.200 mm It is possible to buy the Crane - see offer no Y941 Lodpsbrcy Nsfx Ab Aoru

Condition: used, BROACHING MACHINE Ledpfxst Hr Dfj Ab Asru

Year of construction: 1971, condition: used, General / technical data: Manufacturer: Forst Model: RSIA-20-1320 Year of manufacture: 1971 Weight: 6.000kg Tractive force: 20t Lsdpfx Ajlwu Speb Ajru clearing speed: 5m/min return speed: 16m/min maximum stroke: 1320 broaching positions: 3 clamping area: 370 x 620 x 105mm Remark: The machine is under power in our warehouse and can be inspected.

Condition: used, Year of construction: 2017, 1 Cleaning machine HS200/1600-3, manufacturer: Stenhoj / HESO, year of manufacture: 2017 / 2015, mains connection: 400V, 50Hz, nominal pressure: 4 bar, dimensions (L x W x H): 4.284m x 6.62m x 3.85m / 4.3m x 1.8m x 2m, weight: 1.6t, Stenhoj: electromechanical cleaning machine with lifting table, 200kN at 6m/min including workpiece holder, HESO: used for washing, rinsing and drying workpieces using aqueous solutions, pumps, manufacturer: Ebara, blowers, manufacturer: Becker, operating hours of the individual units: 15,000 / -, average utilization: 85%, last documented maintenance: 04/26/2024, system generally operational, follow-up work has been carried out. Lrsdpfx Abo Aa Acps Aju

Condition: used, Year of construction: 2000, Technical details: pulling force - max.: 2,5 t max. ram stroke: 1000 mm Lrsdpfow Dugasx Ab Aju max. workpiece diameter: 40 mm Broaching speed: 60 m/min. return speed: 20 m/min. total power requirement: 24 kW weight of the machine ca.: 6 t dimensions of the machine ca.: 1,7 x 2,4 x 4,77 m clamping plate: 320 mm It is a hydraulic machine. *

Condition: used, Year of construction: 1999, machine/vehicle number: 17, No minimum price – guaranteed sale to the highest bidder! The machines are still assembled, but disconnected from the power supply. An 11-ton forklift is available on-site for loading. For sale is a vertical internal stripping machine manufactured by FORST, model: RISH 6.3 x 1000xx 320 M. TECHNICAL DETAILS Lrsdpszy Ulrsfx Ab Aeu Operating voltage: 400 V Phases: 3 Frequency: 50 Hz Control voltage: 230/240 V AC Control frequency: 50 Hz Control current: 6.3 A Machine rated current: 180 A

Condition: used, OMAG / AFFRI 903 RSD Hardness Testing Machine Professional, stationary benchtop hardness testing machine from the renowned Italian manufacturer OMAG di AFFRI DAVIDE s.r.l. (Model 903 RSD). Semi-automatic hardness tester for Rockwell, Super-Rockwell, Brinell, and Vickers hardness testing methods according to ASTM and DIN EN ISO. The hardness testers of the RSD series are suitable for all conditions, both in production and in the laboratory. Lrodpfx Aszni D Eeb Aeu Rockwell and Brinell HBTW hardness values with high accuracy (better than 0.5%) in almost any testing environment. Accurate measurement results are achieved with the very first test. The load is applied by means of a dynamic load cell. A user-friendly interface with real-time statistics, graphics, and large archive storage, as well as conversion to other methods, makes measurement a breeze. For hardness testing on almost all metals: iron, steel, hardened steel, cast iron, brass, aluminum, copper, and metal alloys. The device has been regularly inspected and certified by the DAkkS-accredited laboratory 3-Rath Kalibrier + Prüftechnik (last inspection on April 28, 2025, for the HRC method according to DIN EN ISO 9000ff). Technical data: Manufacturer: OMAG / AFFRI Group (Italy) Model: 903 RSD Serial number: 76599 Testing method: Rockwell (including HRC, which is calibrated) Voltage: 115 – 230 V Weight / test force: 195 Kgf Special feature: Height-adjustable testing head for flexible workpiece sizes “Everything from a single source: We would be happy to offer you suitable bank financing for your project.” More items – new and used – can be found in our shop! International shipping costs on request!

Condition: used, functionality: fully functional, Manufacturer: Arthur Klink Year of construction: ca.1960 Type: horizontal broaching machine Model: RH 10-50 Machine. No.: 241 Weight: 3.700 KG General / technical data: used horizontal hydraulic internal broaching machine in a good condition according to age with manual tool feeder in heavy design Clearing stroke: 1,500 mm Tractive force: 10,000 kg (100KN) Mounting in the drawbridge: Ø 85mm Cylindrical Through-hole in the clamping table: Ø 100mm Workpiece clamping surface: Ø 460mm Workpiece diameter: max. approx. 750mm (due to the tool trough of the tool feeder) Cutting speed: hydraulically infinitely variable from 1.0 m/min to 7 m/min Return speed: hydraulically infinitely variable from 5 m/min to 30 m/min Space requirement of the machine: (w x d x h) approx. 6500mm x 950 mm x 1,400 mm (without working area) Power supply: 380Volt 50 HZ Connected load: 8kw Equipment: - the machine has a mechanical hydraulic control for the clearing & return stroke - the machine has an integrated coolant system - the machine has a manually operated tool feed system - The broaching carriage with the pulling head holder is guided flat on both sides. - The machine has an adjustable tractive force limiter Accessories - 1 universal pulling head for flat shafts from 3mm to max. 25mm wide - Adapter sleeve for drawbridge from Ø 85mm to Ø 63mm Remarks: The machine can be used for the production of keyways with flat broaching tools, as well as for profile broaching. Lodper A Hdgefx Ab Aeru In combination with the machine bed of the machine and the stable broaching tool feeder, the machine is well suited for heavy profile broaching tools. The machine is used and is in very good condition for its age. The machine is in our warehouse and can be inspected under power. The machine is currently not technically and visually refurbished, but can be used immediately. Pulling heads for profile broaching are mostly available used on request depending on DIN standard, dimensions and stock. Direct contact details and further information can be found in the attached PDF document

Condition: ready for operation (used), functionality: fully functional, Cable pulling machine / RAUSCH RS 6 /1300 with pulling extension & accessories -Ram stroke / stroke length - Standard 1300 mm (+ pulling extension) -Pulling force 6000 kg -Various cable pulling tools -Various accessories -Workbench Dimensions (disassembled) L x W x H 1.6 x 1.7 x 2.3 meters / Weight 3500 kg Lodpfx Absz I Dbvj Aeru Errors and omissions excepted.

Condition: like new (used), functionality: fully functional, Year of construction: 2025, overall weight: 370 kg, power: 3.5 kW (4.76 HP), input voltage: 400 V, input frequency: 50 Hz, broaching length: 800 mm, broaching speed: 3 m/min, total length: 920 mm, total width: 800 mm, total height: 1,950 mm, Manufacturer: Rausch (Haan/ Rhld) Model: RS 3 G/800 Machine No.: 2968/424 Year of manufacture: 1970 Weight: 370kg Overhaul: 8/2025 by Wiemers AG Our Ref. / Machine No.: WAG 787 General / Technical Data: Unused, overhauled mechanical vertical broaching machine by Rausch Pulling force: 3,000kg (30kN) Broaching speeds: 3m/min and 6m/min Return speed: 3m/min Maximum stroke: 800mm Maximum tool length: 1,000mm Table size / working surface: 340mm x 220mm / 430mm x 310mm Table opening: Ø 90mm for standard broaching mandrels Workpiece diameter: unlimited (without spray guard cabin) Dimensions (h x w x d): 1,950mm x 820mm x 900mm (h = table height from floor without attachments) Motor: 3.5kW Power supply: 400 Volt / 50 Hz Accessories / Special Features: - Modified drive system with geared motor and toothed belt drive - 2 broaching speeds: 3m/min & 6m/min - External stroke adjustment, cross-machine reproducible tool length adjustment system - Integrated coolant unit with check valve and drain cock, including selector switch for automatic operation (does not automatically switch in swivel mode) - Patented coolant/lubricant swivel system - Three-sided enclosed, front-open spray guard cabin (no external operator panel) - Machine enclosure below the safety door with chip guard and tool storage area - Electrical cabling within steel protective conduits - Electrical jaw monitoring (tool removal control to prevent unintended retraction of the pull bridge) - Safety door with integrated emergency stop function - Control panel made from stainless steel sheet with permanent marking - 4 central lubrication points for the trapezoidal spindle drive - Machine documentation Lrodpfx Abjytvyxe Aou Remarks: The machine is fully overhauled, with the frame completely refurbished. The following wear parts have been replaced: - New trapezoidal spindles and spindle nuts made from cast wear-resistant bronze - All bearings and seals replaced - Central drive shaft is new - Coolant system (pump, check valve and drain cock), including coolant/lubricant swivel system, is new - Jaws are new (pull bridge additionally reinforced) - A switchable jaw monitoring system has been installed (additional safety for operators and to prevent tool breakage) - A safety door with interlock has been installed instead of the rubber reach-in protection - Tool length adjustment system relocated outside the machine compartment - Additional limit switches installed - Complete electrical system (control cabinet) with Siemens components is new - Control panel made of stainless steel with durable labeling - New geared drive motor (SEW) with toothed belt drive - Machine has been repainted with 2-component structural paint The machine is stored at our warehouse and can be inspected under power.

Condition: ready for operation (used), functionality: fully functional, "Urpe M-300 G mortising machine with an inclinable head, featuring a 0-300mm stroke, with a stroke rate of 30-35-40 strokes per minute. The distance from the tool to the column is 500mm, and the adjustable distance from the table to the ram is 425-585mm. The maximum distance between the tool and the body is 450mm. The table surface is 800x325mm, with a longitudinal travel of 550mm and a transverse travel of 265mm. The motor has a power of 5.5 hp, and the estimated weight is 1850 kg. It includes a manual indexing head and is in good condition." Lrsdpfoz Tc Iaex Ab Aju

Condition: used, Year of construction: 2008, functionality: fully functional, machine/vehicle number: serie nr 3149, overall weight: 11,800 kg, total width: 6,615 mm, total length: 8,890 mm, total height: 2,050 mm, spindle diameter: 50 mm, type of input current: three-phase, space requirement length: 16,000 mm, space requirement width: 8,000 mm, milling spindle length: 650 mm, compressed air connection: 8 bar, spindle speed (min.): 3,500 rpm, spindle speed (max.): 3,500 rpm, length stop: 3,450 mm, input voltage: 125 V, power: 65 kW (88.38 HP), main saw diameter: 450 mm, corner unit for window and door frames, including tools. controlled from the office (Groeneveld). interpolation (angled pins). barcode laser. return transport. documentation available. complete sets of spare blades/saws, including router bits, linked to Groeneveld. automatic counter-piece. maximum workpiece length 6000. sticker printer for barcode. Ljdpfeztptqox Ab Aeru automatic waxelite pump. automatic central lubrication. connections for pin holes and counter-molds. automatic length stop and rotation for workpieces. including extraction pipes with automatic valve. thicknesses from 38 to 150 mm. pin bank: 1x saw blade 40mm. 2x pin shaft 50x650. 2x edge breaker 30x40. router: 1x rounding router 30x40. 3x router bits 50x600. machine can be picked up here; in conjunction with Bos Machines (dismantling and transport not included in the price). price excludes VAT.

Condition: ready for operation (used), Pulling machine RAUSCH RS 6-1300 with extensive accessories -Ram stroke / pulling length 1300mm -Pulling force 6000kg Lsdpfxjza U Alo Ab Ajru -Incl. 38x clearing pins -Incl. 95x guide bushings -Work bench -Setting plates -Crane -Platform -2x tool cabinets Dimensions: L x W x H 1.6 x 1.7 x 2.3 meters / Weight: 2500kg Errors and omissions excepted.

Condition: ready for operation (used), Keyway cutting machine FRÖMAG RAPIDA 463 incl. INDEXING TABLE - Machinable keyway width: 3 - 63mm - Maximum keyway length: 600mm - INDEXING TABLE - For bores from 10 - 500mm - Feed rate: 0.01 - 0.25mm - Cutting speed, infinitely adjustable: 2 - 22 meters/min - Return speed / constant: 50 meters/min - Load capacity max. 3000 kg - Connection power: 4.6 kW - Includes work platform - Various keyway cutters / accessories & tool cabinet Dimensions: L x W x H 1.6 x 1.5 x 2.3 meters / Weight 3500 kg Errors and omissions excepted. Lsdezl Aiijpfx Ab Asru

Condition: refurbished (used), functionality: fully functional, Year of construction: 1988, machine/vehicle number: 3615/673, input voltage: 400 V, input frequency: 50 Hz, broaching length: 1,000 mm, number of broaching positions: 1, broaching speed: 3 m/min, reverse speed: 3 mm/s, total length: 750 mm, total width: 800 mm, total height: 2,250 mm, -WR 177- Manufacturer: Rausch Model: RS3 /1000 Machine No.: 3615/673 Year of Manufacture: 1988 Weight: 350kg Overhaul: 04/2025 by Wiemers AG Lredpfxjz Hl U Io Ab Aou General / Technical Data: Unused, partially overhauled, mechanical vertical broaching machine Rausch RS 3 without CE marking Pulling force: 3,000kg Broaching speeds: 3m/min Return speed: 3m/min Maximum stroke: 1000mm Maximum tool length: 1200mm Table size / work area: 430mm x 320mm / 340mm x 220mm Table through-hole: Ø 90mm for standard broaching mandrels "System Rausch" Workpiece diameter: any (with the cabin removed) Broaching capacity / keyway width: up to 18mm in steel (from 16mm keyway width only with offset tool shank) Dimensions (h x w x d): 2,250mm x 800mm x 750mm (h = including 3-sided protective cabin) Motor: 3.0kw / Power supply: 400V / 50 Hz Equipment: - Protective door with safety monitoring (emergency stop circuit) - Chip chute - Externally adjustable tool length adjustment system (System Rausch) - Protective cover for stroke adjustment and electrical switching units - Electrical sensing of the clamping jaws (System Rausch) (Tool removal control to prevent unintentional retraction of the drawbar, providing additional safety for the operator & tool) - Integrated coolant system - 4-sided enclosed splash guard hood with protective door - Extra reinforced chip basket and chip sieve with magnet insert - Control panel external - 2 grease points for the trapezoidal spindle drive with manual grease gun directly on the spindle nut Note: The machine has been partially overhauled by Rausch. The following wear parts have been replaced and renewed. - New trapezoidal spindles and spindle nuts made of cast, wear-resistant bronze - All bearings and seals are new - New electrical system - 4-sided enclosed splash guard hood with protective door at the front - New protective door instead of the light barrier in the machine room - New clamping jaws - All sheet metal parts, such as covers, chip chute, basket, sieve and spindle protection, are new. - External control panel General The double spindle drive ensures a smooth and central pulling point as well as a constant broaching speed. The machine is primarily designed for the production of keyways up to 18mm. (from 16mm keyway tools only with offset tool shanks) Due to its design, the machine can be quickly and easily set up for broaching with flat broaching tools for keyways. Due to the structurally universal design of the drawbar and the machine table, broaching with profile and flat broaching tools is possible without the use of additional draw heads.

Condition: used, Drawing machine / stretching machine KARL KLINK RSI 2.5 EH -Pulling force 2500 kg -Stretching speed 1 mm to 9 mm/min (infinitely variable) -Stroke length 800 mm -Max. workpiece diameter approx. 250 mm -Motor power approx. 3 kW -Coolant system -Pulling force indicator Lsdpfxjzwdrvs Ab Ajru -Pulling force limitation -Various guide bushings (see pictures) -Machine feet Dimensions: L x W x H 1.1 x 0.7 x 2 meters / Weight 1600 kg Errors and omissions excepted.

Condition: ready for operation (used), Vertical – Rausch Milling Machine Type RSIZ 6 / 1000 S Condition: Used Technical data: Working range: up to 1000 mm Cutting speed: 3 to 5 m/min Return speed: 10 m/min Internal milling: largest workpiece diameter 600 mm Lrsdjdyp Rmspfx Ab Aou External milling: area of the clamping plate 600 x 340 mm Coolant system Traction force measuring device Central lubrication, automatic Spindle protection with coil spring spirals Chip conveyor Cycle counter Dimensions: 1.05 m x 0.9 m x 4.3 m Weight: 1200 kg Self-collection or shipping by freight forwarder. We will gladly assist you in organizing cost-effective shipping. You are welcome to visit us for an inspection. You will receive a proper invoice. For foreign customers, a net invoice can also be issued. A valid VAT identification number is required. Subject to prior sale. The company names and trademarks mentioned are the property of their respective owners and are used solely for identification and description of the products. The machines and tools are sold as is. The assembly and electrical connection of the machine/device must be carried out or checked by a qualified specialist. Deviations in technical data and errors in the description of the item may occur and are subject to change.

Condition: ready for operation (used), Vertical thread-rolling machine HENNING 03E -Henning - Metzingen -Year of manufacture 1981 -Rolling length approx. 1100mm -Motor power 3KW -Coolant system Dimensions L x W x H 0.7 x 0.5 x 1.7 meters / Weight approx. 450 kg Lsdozkv Euspfx Ab Aoru Subject to errors and omissions.

Condition: ready for operation (used), Emco Test M4C 025 Universal Hardness Tester Hardness Testing Machine Test force range: 9.8-2450N Test height: 260 mm Throat depth: 200 mm Max. workpiece weight: 50 kg Dimensions: 250 mm x 1055 mm x 750 mm (W x H x D) You are welcome to arrange an inspection appointment. We can also organise cost-effective shipping for you! You will receive a proper invoice. For international customers, a net invoice can be provided, provided you have a valid VAT ID number. Subject to prior sale. Visit our shop to see our other offers as well. Lredpfx Aeyybt Esb Aju All company names and trademarks mentioned are the property of their respective owners and are used only for identification and description of the products. Deviations from technical data or errors in the description of the item may occur and are subject to change.

Condition: refurbished (used), functionality: fully functional, Year of construction: 2024, broaching length: 1,000 mm, number of broaching positions: 1, broaching speed: 3 m/min, Manufacturer: Rausch (Haan/Rhld) Model: RS 6/1000 Machine No.: 51261 Year of Manufacture: 1978 Weight: 680 kg Overhauled: 11/2024 by Wiemers AG General Information / Technical Data: Overhauled mechanical vertical broaching machine Rausch RS 6 G Pulling force: 60 kN Broaching speeds: 3 m/min and 6 m/min Return speed: 6 m/min Maximum stroke: 1000 mm Maximum tool length: 1200 mm Table dimensions / Working area: 610 x 470 mm / 520 x 320 mm Table aperture: Ø90 mm for standard broaching mandrels Workpiece diameter: unlimited Dimensions (H x W x D): 2,250 mm x 850 mm x 1,200 mm (H = table height from floor, without attachments) Motor: 4.4 kW / 5.5 kW Power supply: 400 Volt / 50 Hz Additional modifications/upgrades to the original machine performed: - External stroke adjustment - New, machine-independent, reproducible tool length adjustment system - Additional limit switches for end position monitoring - Safety door with monitoring (integrated in the emergency circuit) - Machine enclosure below safety door with chip protection and tool storage area - Electrical sensing of clamping jaws (tool removal monitoring to prevent unintended retraction of the broaching bridge) - Coolant swing system with solenoid valve operated during swing motion (for switching on coolant before broaching stroke – optical flow control ensures lubrication, no dry cutting!) - Routing of electrical cables in protective steel conduits - Heavy-duty control cabinet mounting for machine components - Additional oil-proof drip tray on the control cabinet - Three-sided closed splash guard cabin (W = 960 x D = 450 x H = 590 mm) - Reinforced chip screen with magnetic separator - Control panel made of stainless steel with durable labeling - 4 central lubrication points for trapezoidal spindle drive Remarks: The machine has been completely overhauled, the machine body fully refurbished. All wear parts have been replaced. - New trapezoidal spindles and spindle nuts made from cast wear-resistant bronze - All bearings and seals renewed - The coolant system (pump, solenoid valve, and drain tap), including the coolant/lubrication swing system, is new - The clamping jaws are new - Complete electrical system (control cabinet) is new - All sheet metal and enclosures are new - The following components have been overhauled and re-used: - Machine base - Machine column - Machine table with table insert - Broaching bridge (clamping jaws new) - Gear wheels - Electric motor (new brake, new bearings) The machine is stored in our warehouse and can be inspected under power. The attached images are original photos of the machine. The machine is CE marked. Ledpfx Asw Ighijb Aoru The CE marking corresponds to the status as of 1998 (first overhaul).