Used Bauknecht Rf0,25/6-7 for sale (63,788)

Condition: used, Gear motor, electric motor -Speed: 11.5 rpm -Power: 0.18 kW Pjdpfsckd D Rex Af Sorb -Construction: B3 -Diameter shaft: Ø 32 mm -Protection class: IP 44 -Weight: 24 kg

Condition: good (used), Gear motor, electric motor, electric gear motor -Speed: 19.5 rpm -Power: 0.25 kW -Diameter shaft: Ø 25 mm -Construction: B5 Prsdociq Dtjpfx Af Seb -Price: per piece -Number: 1x available -Protection class: IP 44 -Dimensions: 390/170/H190 mm -Weight: 16 kg

Year of construction: 2013, condition: used, 1) Perfecta 168 TS high-speed cutter, cutting width: 1680mm, usable rear table length: 1680mm, max. clamp opening: 165mm, min. residual strip: 26mm, max. clamping force: 60kN, table height: 890mm, operating hours: approx. 15813h, total cut counter: 349265cuts, weight: approx. 6900kg. Including material hold-down, turning saddle, six carbide knives and five knife cases. 2) Perfecta ZTS 2750 gripper transport system for automatic feeding of the high-speed cutter via the rear table, max. travel: 2750mm, max. clamp opening without/with adapter: 165mm/135mm. 3) Perfecta BASA 7 automatic jogging machine, max. sheet size: 1260×1670mm, min. sheet size: 550×660mm, max. stack height: 1400mm, grammage range: 60-300g/m², feeding from the right or left possible. 4) Perfecta BA 6 unloader, max. size: 1050mm×1450mm, max. layer height: 160mm, max. stack height: 1400mm, max. load capacity: 300kg. Equipped with 15inch touchscreen, USB and Ethernet interface as well as direct processing of prepress data on the machine control without additional hardware, CIP 3 ready, CIP 4 optional. Including spare parts package with wear parts. External compressed air connection with 6bar required. The system is in very good condition. Sale preferably as a complete system. Documentation available. An on-site inspection is possible by appointment. Predjzz Iq Rspfx Af Sjb

Year of construction: 2025, condition: like new (used), Replacement shafts for Lindner Urraco 75 for sale High-quality replacement shafts for a Lindner Urraco 75 shredder are for sale. – Application: Old wood, household and commercial waste – Predpfx Afjzphiie Sjb Condition: New / very good condition Design: Original Lindner shafts, not replica shafts The shafts are ready for immediate use. The price stated is net. Notes: • Sale is made excluding any warranty or guarantee. • No returns or renegotiations. • Subject to prior sale. All information is without guarantee. The seller assumes no liability for any errors, omissions, or changes to the information. The sale is made exclusively subject to prior sale.

Condition: used, Year of construction: 2001, functionality: fully functional, machine/vehicle number: 200101521101, measuring range X-axis: 700 mm, measuring range Y-axis: 1,000 mm, measuring range Z-axis: 600 mm, year of last overhaul: 2026, Equipment: type plate available, For sale is a ZEISS CONTURA 7/10/6 coordinate measuring machine (CMM) with a ZEISS VAST XT gold scanning probe system and a C99 control panel. The machine is located in Velbert (North Rhine-Westphalia) and was last calibrated in February 2026. Manufacturer: Zeiss Model: SYS CONTURA 7/10/6 Part number: 623564.9010.000 Serial number: 200101521101 Year of manufacture: 01/2001 Automatic probe changer, 5 positions Measuring software: ZEISS CALYPSO 2021, version 7.2.08 Last major maintenance including calibration: 02/2026, performed by Zeiss Condition: used / operational Machine type: Coordinate measuring machine AVAILABLE FROM JANUARY 2027 Disassembly and transport are to be arranged by the buyer. If you have any questions or require further information, please do not hesitate to contact us. Prsdpfx Ajz Duv Aef Sjb

Condition: excellent (used), Year of construction: 2001, functionality: fully functional, measuring range X-axis: 700 mm, measuring range Y-axis: 700 mm, measuring range Z-axis: 600 mm, Equipment: type plate available, Eclipse 7/7/6 CNC Technical specifications: Measuring range X = 700 mm, Y = 700 mm, Z = 700 mm C99 control system with BP26_SE operating panel Renishaw TP20 probing system Prsdjz Egllspfx Af Ssb Equipment: Calibration sphere Probing accessories HP computer with 27" monitor Software: Calypso Basic 2017 CNC Preset module Freeform surface Upgrade to the latest version possible The machine is in excellent technical and visual condition and has very few operating hours. Available immediately.

Condition: used, Year of construction: 2023, Used System Year of Manufacture: 2023 Condition: Like new, very few operating hours Features and Technical Specifications: ECO JET DUO 6 XL ZRS stationary clean air filtration system for extracting wood dust and chips Pjdjzlbqropfx Af Sorb Fans: 2 x 7.5 kW Airflow: 10,000 m³/h Vacuum pressure: 2,700 Pa (total) / 2,200 Pa (static) 80 filters, each 2.50 m long, BIA Category M, electrically conductive, incl. support baskets Filter area: 77.6 m² Filter loading: 129 m³/(m² x h) Filter cleaning: AL-KO OPTI-JET® Pressure relief areas: 0.84 m² (rupture discs) Base structure with hopper and rotary valve; dry conveying with C-coupling ECO JET DUO 6 ZWR XL, 1,100 mm spacer ring for raising the unit, with 2 intake openings Base unit with feed hopper and ZRS 960/1 FG rotary valve for chip disposal via a customer-supplied transport fan into a silo or similar; transport line DN 200, approx. 1,260 mm, connection to be provided by the customer Rotary valve ZRS 960/1 FG: - ATEX Directive 94/9/EC; CE 0588 Ex II 1D/- (unit for indoor/outdoor use); EX D; FSA 11 ATEX 1614X - Motor: 0.18 kW / 0.78 A, 3-phase / 400 V / 50 Hz - Protection class/enclosure type: IP 54 / B3; Insulation class F - Speed: 41 rpm; Flow rate: 15,744 l/h*; 7 cells - Inlet/Outlet: 960 x 250 / 960 x 208 mm - Dimensions: 1,100 x 605 x 330 mm; Temperature range: up to 50 °C Additional features: - 400 mm suction inlet with check valve in rectangular duct - ECO JET backflow check valve 910 x 346 x 500 mm AL-KO Control System ACS II: - Touchscreen display, ST 1200 controller, Sitop Power power supply, 24 V control voltage, and integrated frequency converter for cascading up to 2 fans up to 37 kW with frequency converter transfer - Plain-text error messages on the display, as well as a collective error message and indicator light; manual start of discharge via display button and cleaning via button; cleaning start via differential pressure; Post-cleaning; external start via potential-free contact; operating hour counter; maintenance interval indicator; control cabinet lighting and ventilation; monitoring/evaluation of fire damper, residual dust sensor, fill level sensor, and maximum filter pressure - 10 individually controlled solenoid valves - Gate valve control in groups of 4 for up to 8 machines: control via potential-free contact (PFC) or induction coil; 24 V DC shut-off valves, motor-driven with single-wire control or electropneumatic; max. 4 plates per conveyor line - ZRS power module up to 0.18 kW; time parameters adjustable via touch display - Rupture disc sensor and evaluation unit; pressure transmitter for frequency converter; pressure cells; strobe light; 2 x PTC thermistor evaluations; rotation monitoring of the rotary valve - 24 V DC supply air/return air switching for summer/winter operation - Filter monitor/residual dust monitoring with evaluation unit in accordance with DIN EN 12779 and H3: If 0.3 mg/m³ is exceeded, a self-holding alarm is triggered and the recirculation damper switches to exhaust air - 10-terminal junction box, 24 V/230 V, fully wired for filter cleaning, including approx. 6 lfm of cable - Ducting system including elbows, branch pipes, reducers, PU hoses, machine connections, small parts, and EP dampers for exhaust from 11 woodworking machines 1 HRS as specified - Return air system in accordance with TRGS 553, with changeover damper and fire damper - Galvanized base frame for container l...

Condition: good (used), Year of construction: 2016, functionality: fully functional, Currently, a machine overhaul is being carried out with a value of €90,000. Maho DMF 260 -7 / 5-axis machining center Year of manufacture 2016, Control system: Heidenhain ITNC 530, Travel range X/Y/Z: 2600/700/700 mm, Fixed table with integrated NC rotary table, B-axis in the milling head, infinitely adjustable, Spindle speed up to 14,000 rpm, Tool holder: HSK A63, Coolant: 60 bar, Coolant pressure: 40 bar, Paper band filter, 3D measuring probe Heidenhain TS 649, 3D Quickset, Podpfx Aozxfz Iof Sjrb Machine protection control, Electric handwheel, 3D data model.

Condition: used, mileage: 580 km, power: 66 kW (89.73 HP), first registration: 05/1962, fuel type: diesel, number of seats: 22, gearing type: mechanical, color: beige, Year of construction: 1962, Available in multiple colors (yellow/red/green), built between 1957 and 1964. We also have 8 restoration projects ready to start immediately. Podpfx Afezyx Nzs Sjrb Features: 8 sleeping seats or 20 seating capacity * Double tour guide seat * Large club lounge for 8-seat configuration Length: 6,650 mm Width: 2,250 mm Permissible total weight: 6,200 kg Complete restoration Henschel engine Steering wheel manual transmission Roof luggage rack German historic (H) registration, passenger coach - Rental for your event possible. Europe-wide delivery available with our vehicle transporters. We have a wide selection of classic Setra buses: S6, S7, S9 to S14, Mercedes O 319 and O 3500, Saurer bonnet buses. We make shipment worldwide. Net price: 165,000.00 Euro

Condition: good (used), Year of construction: 2000, working width: 900 mm, total width: 1,800 mm, total length: 12,000 mm, total height: 3,550 mm, overall weight: 8,000 kg, For sale: Konig combi bread line 8/7/6/4 rows Includes: - TRO 240 hopper with oiling system - Konig Industrie Rex head machine Model A - Spreading conveyors - Proofing cabinet model: KGV V L Type: (900/500) K8 - V0 - (W) - R - RR900 - SCHN7/B - MO(WB) 1000 - STb8/7/4 - Stamping unit - Long roller - Seed station - Drop tables (8/7/6/4) (4 different drop tables with various belts included) - Storage trolley for the drop tables - Storage trolley for the flour sprinklers - Spare parts - Control cabinet - All documents and electrical diagrams Weight range: 20 to 30 grams up to 110 grams Output: 18,000 / 24,000 pcs per hour Working width: 900 mm New drum in the Industrie Rex Many spare parts such as spreading belts, etc. Podpjxnb Iijfx Af Sjrb It is possible to inspect the line on site. We can carefully load the line onto a truck/container. Do you have comments or questions? Please feel free to contact us. Best regards, Leo Holland

Condition: used, Year of construction: 2002, grinding diameter 450 mm grinding length 1500 mm centre height 225 mm Control FAGOR EQUIPEMENT Prjdpfxouxfu Ne Af Sjb - T1: grinding wheel diameter 500 mm - T2: grinding wheel diameter 400 mm - T6: HF Fischer spindle MFV or MFZ 1224/1242/1260 - T7: HF Fischer spindle MFV or MFZ 1224/1242/1260 - Marposs tool measurement - active longitudinal positioning - Elaso GAP-control on T1 and T2 contactless integrated in the control surface - Elaso GAP internal grinding with fluid sensor for T6 and T7 - semi-automatic balancing by Elaso integrated in the control surface for T1/T2 - tailstock hydraulic with fine adjustment +/- 150 microns - dresser on workpiece spindle side table mounted - dresser on tailstock side table mounted - dresser on upper table - new service- and userfriendly housing SPECIAL EQUPEMENT: Workhead with direct drive - strongly recommended for non-circular grinding - workpiece weight flying max. 75kg - workpiece weight between centres 150kg - water-cooled B-axis with direct drive - center height 225 mm - extremely torsionally stiff - highly accurate positioning - resolution ° - water-cooled Hydrostatic ball screw - x-axis - wear-free, as there is no contact during operation - no loss of precision, even during long-term use at full load and maximum speed - no friction at low speeds - no friction force backlash when the direction of rotation changes - translates even the smallest rotational movements - no stick-slip effect even at low speeds - no fluctuations in frictional torque due to ball circulation - higher axial stiffness compared to ball screws - significant improvement in damping, resulting in better workpiece surface finish and tool life - no oscillations due to ball circulation - also suitable for high speeds and accelerations - cost-effective alternative to the linear motor with greater precision and significantly lower heat generation - significantly less power dissipation and, as a result, no problems with swarf on permanent magnets New hydraulic unit - optimized temperature control (chiller) - Energy-saving Only one pump controlled by VFD - Pressure monitoring - monitoring of the hydrostatic oil for water content. (Damage to the bellows is recognised and detected prematurely) -fine adjustment +/- 150 microns Paper belt filter 375l – alternative 480l Grinding mist extraction system – emulsion MECHANICAL OVERHAUL -complete machine according to Kellenberger protocoll -new painting ELECTRICAL OVERHAUL - new modern Fagor CNC with BEMA HMI - new electric cabinet - new digital drive technology - replacement of all electrical cables, switches etc. - new absolute external scales in x- and z-axis - new absolute encoder (B-axis) Grinding software BEMA-Standard: - workpiece zeroing - grinding wheel zeroing - dressing diamond measuring - corrections - external and internal surface grinding - external and internal angle grinding (turning of the b-axis, dressing with straight wheel) - external and internal radius grinding (radius dressed on wheel) - semi-automatic traverse grinding - workpiece zeroing - 2 dressing diamonds - 1 dressing blade - dressing roll - 3 flat dresser - corrections - Z-position measurement - GAP control Optional grinding cycles at no extra charge: Profile plunge grinding: - external and internal profile plunge grinding with profile wheel Pr...

Condition: used, Year of construction: 2023, Offered for sale is a self-adhesive labeling machine. Nominal output: 11000bottles/h, reference circle diameter: 720mm, control range: 2000 to 12000bottles/h, number of container plates: 12, pitch: 188.4mm, starwheel diameter: 480mm, starwheel pitch: 8, number of self-adhesive labeling stations: 2, direction of operation: left-hand machine, control: touch panel. Equipped with infeed screw 1x, infeed/outfeed starwheel 1x, bottle plates 1 set, centering hoods 1 set, swivel arm, free-standing control cabinet. Inspection possible by appointment. Prodpfx Aezzdybof Sob

Condition: used, Year of construction: 2013, Format Parts Bottle Diameter : 57,71,76,94,115mm Pjdpfjzx Dg Asx Af Sjrb

Condition: excellent (used), Year of construction: 2010, functionality: fully functional, machine/vehicle number: P260713253, 𝘼𝙪𝙩𝙤𝙢𝙖𝙩𝙞𝙘 𝘿𝙤𝙪𝙗𝙡𝙚-𝙀𝙣𝙙 𝙋𝙧𝙤𝙛𝙞𝙡𝙞𝙣𝙜 𝙇𝙞𝙣𝙚 𝙛𝙤𝙧 𝙋𝙖𝙧𝙦𝙪𝙚𝙩 𝙁𝙡𝙤𝙤𝙧𝙞𝙣𝙜 1. 𝗚𝗲𝗻𝗲𝗿𝗮𝗹 𝗜𝗻𝗳𝗼𝗿𝗺𝗮𝘁𝗶𝗼𝗻 • HOMAG OPTIMAT FRP225/7/10PL/L – Longitudinal Profiling Machine • HOMAG OPTIMAT FRP226/5/5PL/Q – Cross Profiling Machine Automatic, high-speed double-end profiling line designed for the production of solid wood, engineered wood, and laminate flooring. The line performs precision machining on all four edges, including tongue-and-groove and click-locking profiles. 2. 𝗠𝗮𝘁𝗲𝗿𝗶𝗮𝗹𝘀 𝗣𝗿𝗼𝗰𝗲𝘀𝘀𝗲𝗱 • Solid hardwood flooring • Engineered wood flooring • Laminate flooring • Multi-layer parquet • Decorative flooring panels 3. 𝗠𝗮𝗶𝗻 𝗧𝗲𝗰𝗵𝗻𝗶𝗰𝗮𝗹 𝗦𝗽𝗲𝗰𝗶𝗳𝗶𝗰𝗮𝘁𝗶𝗼𝗻 Parameter Specification Machine Type Double-End Tenoner / Profiling Line Longitudinal Machine HOMAG FRP225 Cross Machine HOMAG FRP226 Maximum Feed Speed Up to 80 m/min Working Principle Continuous automatic feed Number of Working Units 7 (FRP225) + 5 (FRP226) Total Working Units 12 Production Mode Continuous 4. 𝗪𝗼𝗿𝗸𝗽𝗶𝗲𝗰𝗲 𝗖𝗮𝗽𝗮𝗰𝗶𝘁𝘆 Parameter Typical Range Thickness 5–25 mm Width Customer-specific configuration Length Customer-specific configuration 5. 𝗠𝗮𝗰𝗵𝗶𝗻𝗶𝗻𝗴 𝗢𝗽𝗲𝗿𝗮𝘁𝗶𝗼𝗻𝘀 The line is capable of performing: • Longitudinal profiling • Cross-end profiling • Tongue machining • Groove machining • Click profile machining (depending on tooling) • Micro-bevel production • Relief grooves • Edge trimming • Sizing and calibration • Four-side profiling 6. 𝗠𝗮𝗰𝗵𝗶𝗻𝗲 𝗖𝗼𝗻𝗳𝗶𝗴𝘂𝗿𝗮𝘁𝗶𝗼𝗻 HOMAG FRP225 Function • Longitudinal edge profiling Configuration • Six machining units • High-frequency spindle motors • Precision side guides • Automatic pressure system • Heavy-duty chain conveyor HOMAG FRP226 Function • Cross-end profiling Configuration • Four machining units • Automatic synchronization with FRP225 • Precision positioning system • High-speed transfer conveyor 7. 𝗗𝗿𝗶𝘃𝗲 𝗦𝘆𝘀𝘁𝗲𝗺 • High-frequency spindle motors • Variable-speed feed drive • Precision chain transport system • Pneumatic pressure rollers • Servo-controlled positioning (depending on machine version) 8. 𝗧𝗼𝗼𝗹𝗶𝗻𝗴 • Leitz • Leuco • Kanefusa • AKE • Tigra Typical tooling: • Profile cutters • Grooving cutters • Chamfer cutters • Relief cutters • Diamond tooling (PCD) 9. 𝗠𝗮𝗰𝗵𝗶𝗻𝗲 𝗖𝗼𝗻𝘁𝗿𝗼𝗹 • Siemens PLC control system • Frequency-controlled spindle drives Pedpfx Afezmrw So Sjrb • Digital machine diagnostics • Electronic feed speed adjustment 10. 𝗣𝗿𝗼𝗱𝘂𝗰𝘁𝗶𝗼𝗻 𝗣𝗲𝗿𝗳𝗼𝗿𝗺𝗮𝗻𝗰𝗲 Parameter Typical Value Feed Speed Up to 80 m/min Production Capacity Approximately 1,500–4,000 m² per shift* 11. 𝗧𝘆𝗽𝗶𝗰𝗮𝗹 𝗣𝗿𝗼𝗱𝘂𝗰𝘁𝗶𝗼𝗻 𝗟𝗶𝗻𝗲 𝗟𝗮𝘆𝗼𝘂𝘁 1. Automatic infeed system 2. HOMAG FRP225 longitudinal profiler 3. Automatic transfer section 4. HOMAG FRP226 cross profiler 5. Inspection station 6. Automatic stacker 12. 𝗠𝗮𝗶𝗻 𝗔𝗱𝘃𝗮𝗻𝘁𝗮𝗴𝗲𝘀 • High dimensional accuracy • Excellent profile repeatability • High production speed • Fast tooling changeover • Continuous automatic operation • Suitable for traditional tongue-and-groove and modern click systems • Reliable industrial design for high-volume production 𝗧𝘆𝗽𝗶𝗰𝗮𝗹 𝗔𝗽𝗽𝗹𝗶𝗰𝗮𝘁𝗶𝗼𝗻𝘀 • Solid parquet flooring • Engineered flooring • Laminate flooring • Luxury wood flooring • High-precision click flooring systems

Condition: excellent (used), Year of construction: 2001, NOWICKI MA-7-6000PSCH tumbler Capacity: 6000 liters Predpfezmwgrsx Af Seb The machine is equipped with a cooling system.

Condition: excellent (used), Year of construction: 2006, functionality: fully functional, machine/vehicle number: 04 24446, Folder incl.: Paper format: 760x1100mm Maximum speed: 180m/min 6 cassettes Prodsztp Axepfx Af Sjb 2 knives 1 side cassette after the knife Pallet loading MBO SBAP-82ME stacking press SBAP 46 ME sheet press stacker delivery unit

Condition: ready for operation (used), Year of construction: 1996, functionality: fully functional, machine/vehicle number: 035-804, input voltage: 400 V, type of input current: three-phase, Equipment: CE marking, Year of manufacture 1996, the latest tools were acquired in 2024. Production of wood and wood-aluminum windows. Oppold IV67 mm wood and wood-aluminum. Also production of entrance doors and lift-and-slide doors. The production line is still fully assembled and functional. Additional tools: Zuani IV79 and IV91 for wood and wood-aluminum, for EUR 7,700. If you have any questions or require further information, please feel free to send us a message or call us. Psdpfx Aszlytxjf Sjrb

Year of construction: 2008, condition: ready for operation (used), Offered for sale is a Kern Kraft chamber filter press. Max. filtration capacity: 2000l/24h, number of filter plates: 10 standard, expandable to 20, filter area range: 3.9m²-8m², chamber volume: approx. 40l. Equipped with plates and cloths, pressure switch, stainless steel filter cake tray and stainless steel piping, expansion tank, check valve and automatic shutdown, pump and candle filter housing with filter cartridge and control cabinet. Dimensions X/Y/Z: 2500mm/1000mm/1800mm, weight: approx. 630kg. An on-site inspection is possible. Psdpfx Aeztzqnef Sjrb

Condition: used, mileage: 463,000 km, power: 353 kW (479.95 HP), first registration: 10/2013, fuel type: diesel, overall weight: 40,000 kg, brakes: retarder, gearing type: mechanical, emission class: euro5, Equipment: crane, soot filter, Crane: Prsdpfx Aoz Hh Dref Seb ----- Retarder, air conditioning, lifting mechanism, and steering axle – Effer 955 (855) with fly jib and cable winch Suspension: Leaf spring/air suspension

Condition: excellent (used), Year of construction: 2000, machine/vehicle number: EWD DWK T-4, Log infeed Reducer Debarking Block conveyor EWD ZE infeed table Microtec 3D measurement Spaner FZ3 Roller unit EWD EVW Flexible double-shaft circular saw EWD DWK 700 T-6 6 flexible saw axes Cutting height 60-340 mm 2x200 kW Complete Siemens S7 control system, year 2014 Psdsz Ar N Hopfx Af Serb Complete hydraulics/control cabinets

Condition: excellent (used), Year of construction: 2000, machine/vehicle number: EWD DWK, Log infeed Reducer Debarking Block conveyor EWD ZE infeed table Microtec 3D measurement Spaner FZ3 Roller unit EWD EVW Flexible double-shaft circular saw EWD DWK 700 T-6 6 flexible saw axes Cutting height 60-340 mm 2x200 kW Complete Siemens S7 control system, year 2014 Complete hydraulics/control cabinets Prjdpoz Ar N Tjfx Af Seb

Condition: refurbished (used), Year of construction: 2016, operating hours: 20,169 h, functionality: fully functional, machine/vehicle number: 512822, overall weight: 51 kg, load capacity: 6 kg, arm reach: 706 mm, This is a KUKA KR 6 R700 WP industrial robot with a KRC4 controller, manufactured in 2016. This robot has been fully overhauled! The controller includes the following options: KUKA.CPC KUKA.Platform BoardPackage Pedpfxozwfmzo Af Sjrb ExpertTech KUKA.PROFINET MS KUKA.UpdatePackageFirmware KUKA.UpdateService KUKA.UpdateServiceConfiguration

Condition: used, mileage: 125,000 km, power: 132 kW (179.47 HP), fuel type: diesel, fuel: diesel, color: white, gearing type: automatic, emission class: euro6, loading space length: 6,100 mm, loading space width: 2,500 mm, loading space height: 2,370 mm, Year of construction: 2020, Equipment: ABS, air conditioning, central locking, cruise control, electric window regulation, spoiler, tail-lift, Year of manufacture: 2020 Empty weight: 4.358 kg Carrying capacity: 3.132 kg GVW: 7.490 kg Prjdpfxjznba Sj Af Ssb Tail lift: tail lift, 1000 kg = Additional options and accessories = - Airbag - Beifahrerbank - Front center armrest - Outside temperature display - Radio - Reversing camera - Roof spoiler - Suspension seat - Tachograph - Tined glass - Toolbox

Condition: good (used), Gear motor, electric motor, electric gear motor -Speed: 20 rpm -Power: 0.25 kW -Design: B5 -Shaft: Ø 25 x 60 mm Prjdpfx Afodwkymj Sob -Bolt circle: 130 mm -Recess: 110 mm -Protection class: IP 55 -Dimensions: 400/160/H220 mm -Weight: 17 kg

Condition: excellent (used), Year of construction: 2020, functionality: fully functional, CNC machining center Hedelius Forte 7-2600 Magnum Prsdpfx Aezzl Ugef Sob Control system: Heidenhain TNC 640 Year of manufacture: 2020 Availability: in transit Internal machine no. 73 Travel distances: X-axis 2,600 mm Y-axis 750 mm Z-axis 800 mm Swinging operation: 2 x 1,000 mm Total clamping area: 2 x 1,490 x 750 mm Table load: approx. 2,500 kg Tool holder: HSK 63 Tool magazine: 50 positions Spindle speed: 50 - 18,000 rpm Drive power: 35 kW Equipment: - Inclined bed coolant system 900 l - Chip conveyor - 2 x flushing guns - Electronic handwheel - Partition wall prepared - High-pressure pump 60 bar - 0-point clamping plates - Vises and tools as required - Prepared for work area partition