Used Automated Paint Shops for sale (18,456)

Condition: new, AUTOMATED PAINT SHOPS These are the paint shops where your product is designed and manufactured by our engineers in line with your capacity, use area and other demands. Chsdpfx Ajdy Ez Ijfgjc Maximum efficiency is aimed to be provided with minimum staff and the least space usage at electrostatic powder coating or wet paint, sandblasting, varnishing, glazing, coating, washing and similar system requirements.

Condition: new, Equipment: cabin, Stationary small parts spray booth Dixi █████ Achieve perfect and uniform coating of small parts. The extraction system ensures optimal results even in the smallest spaces. Optionally equipped with a turntable or a wheel holder, as well as a compact yet powerful extraction unit, it is perfectly suited for processing small workpieces and wheels. The side panels effectively limit the distribution of overspray, allowing work to be carried out in confined spaces without contaminating surrounding areas. Integrated lighting is also available as an option. Additionally, thanks to its low weight and minimal connections, the booth can be relocated to a new site in no time, ensuring your flexibility at all times. The system comes fully pre-assembled and ready for immediate use. Your Benefits Codpfxoxa Hx Re Afgshc Thanks to its compact design, flexible dimensions, and versatile accessories, this booth offers a broad range of applications. The sophisticated modular system requires minimal space and is therefore suitable for use in virtually any premises. Different filter media and stages enable highly efficient operation, while filter changes can be performed in just a few minutes. Application and Safety Processing of both water-based and solvent-based coating materials is enabled by the use of ATEX-certified explosion-proof motors. It can also optionally be used for spraying adhesives. The large filter surface ensures uniform extraction throughout the process.

Condition: good (used), Year of construction: 2003, The painting unit with heat exchanger and blowing for drying was used in the production of stairs and carpentry elements Paint wall also with extraction in the floor with a total length of about 7 mb equipped with three extraction fans Cjdouyy A Dspfx Afgjhc

Condition: new, Powder Coating Systems For years, powder coating has been continuously evolving as an alternative to wet painting, and it has recently gained increasing importance due to its lower environmental impact—specifically the absence of solvents and paint sludge. Powder recovery further boosts the efficiency of these systems to a particularly high level. For users, powder coating offers the advantage of creating an extremely durable and corrosion-resistant surface that is significantly more impact-resistant than what traditional painting can achieve. Additionally, post-processing tasks such as grinding or drilling the powder-coated parts present no problems, as the coating will not chip off. Pony Luxury Coating powder coating systems provide you with tangible advantages: they are efficient, environmentally friendly, and—as always—unsurpassed in flexibility. We achieve this through a range of system types. Manual Powder Coating Systems Manual coating systems are the ideal solution for complex and demanding workpieces. Thanks to skilled operators, these systems offer continuous adaptation to changing conditions and varying product sizes. Flexibility is paramount—with the added benefit of an attractive entry price into the world of powder coating. Large-Scale Powder Spray Booths No matter how large or challenging your workpieces, our systems are larger! In the commercial vehicle and utility sector, where components are exposed to significant stress, powder coating has established itself as the ideal solution. To accommodate ever-larger components, we offer our large-scale powder booth, which supports unlimited manual coating, and, when combined with a conveyor system, handles any workpiece size with ease. Automatic Powder Coating Systems If your operation requires high throughput and rapid processing, an automated powder system is the way forward. Coupled with a conveyor, light barriers allow precise detection and, consequently, exact powder dosage to ensure maximum efficiency. The system can also be equipped with lifting stations and robots to handle even the most complex components. Chodpfx Afjxa Hzxegoc Powder Curing Ovens & Flash-Off Dryers These provide the perfect finishing touch to powder coating: the curing oven. Our ovens feature the highest insulation class, ensuring consistent, high efficiency. Detailed temperature control also enables use as a flash-off dryer to dry substrates after pre-treatment. Temperatures up to 250 degrees Celsius are possible, which allows usage as a tempering oven, for instance with hot-dip galvanized materials. Of course, typical use as a powder curing oven is straightforward. Optimal air distribution and a visualized control panel prevent over-baking, and even allow multiple color shades to be cured in a single process. Do you have questions or suggestions? We are happy to assist you!

Condition: good (used), Year of construction: 2005, Complete industrial paint booth, manufacturer Walther: 1 single booth + 1 double booth. Drawings with dimensions are available upon request. Chsdpfx Aoxvbdmjfgjc

Condition: ready for operation (used), Year of construction: 2006, working width: 150 mm, overall weight: 150 kg, Conveyor Belt 2500 mm Manufacturer: Makor Type: TEP 2500 Powered conveyor belt from a finishing line (positioned in front of a Makor profile spraying machine), Length approx. 2500 mm Belt width: 150 mm Pass-through width (with existing side guides): max. approx. 320 mm Feed speed steplessly adjustable via variator Chjdpfx Ajxtnfrofgjc Equipped with stable, adjustable side guides Dimensions approx. 2500 x 550 mm (LxW) Weight approx. 150 kg Documentation available

Condition: good (used), Year of construction: 2015, functionality: fully functional, workpiece weight (max.): 40 kg, CABO Mixspace Multispeed Paint Mixer Gyroscopic Mixer (gyromixer) Year of manufacture: 2015 Display Alphanumeric 20 x 4 Maximum bucket weight 40 kg Bucket holder tray Pull-out Bucket gripper Automatic Gyroscopic ratio 1:1.8 Speed ​​settings 3 programmable Mixing speed 80 - 180 rpm Chedevmtw Ropfx Afgjc Acceleration / deceleration during the mixing cycle Automatic speed adjustment to the bucket height Mixing cycle time 20sec - 30m Maximum bucket diameter 380 mm Bucket height: min - max 90 - 490 mm Bucket height 340 (+30) mm Bucket types Round/Square/Oval Mains voltage: 230v 50Hz 3A Machine weight 190 kg machine dimensions: width:860mm length:850mm height:1150mm

Condition: new, Year of construction: 2026, total height: 3,000 mm, total length: 4,900 mm, total width: 2,400 mm, volume flow: 3.6 m³/h, type of input current: three-phase, power: 1.1 kW (1.50 HP), Equipment: cabin, Wet paint spray booth in cabin with extraction and supply air filter, lighting. Chsdpervi Risfx Afgec

Condition: new, Year of construction: 2025, functionality: fully functional, total height: 5,600 mm, total length: 11,200 mm, total width: 5,100 mm, type of input current: three-phase, warranty duration: 24 months, inner dimension height: 4,970 mm, inner dimension length: 11,000 mm, temperature: 80 °C, inner dimension width: 5,000 mm, air demand: 52,000 m³/h, input voltage: 380 V, heating capacity: 250 kW (339.91 HP), power: 45 kW (61.18 HP), fuel: liquid petroleum gas (LPG), input frequency: 50 Hz, energy consumption: 45 kWh, insulation thickness: 50 mm, nominal power: 250 kW (339.91 HP), sheet thickness steel (max.): 2 mm, Equipment: lighting, * Air Preparation Unit: The air preparation unit is a recirculation system that supplies the cabin with filtered fresh air and exhausts used air during the painting process. It heats the air to 60 °C, mixes the used air with 10% fresh air via an automatic multi-damper system, and reheats the air before routing it back into the cabin. The air is heated using a burner and a heat exchanger, both made of high-quality 304 stainless steel and housed within the fresh air unit. During painting, the air is filtered twice (via front and ceiling filters) before it enters the cabin. The contaminated air is also filtered twice (through inlet and outlet filters) before it exits via the exhaust unit. Air preparation units are insulated like the side walls to minimize heat loss and are protected against potential vibration and noise thanks to rubber seals on the covers. The exhaust air is regulated by a damper in the outlet duct, which helps control the internal pressure of the cabin. * PRINCIPLES OF CABIN OPERATION: The processes in the cabin are controlled via a control panel that manages the following steps: * PAINTING PROCESS: During painting, 100% fresh air is drawn in from outside and passed through front filters before entering the distribution chamber at ambient temperature. The air is then expelled by the extraction unit. Floor filters (paint stops) capture paint particles, and the air passes through the final exhaust filters before being discharged. Cjdpfewzl Hxox Afgehc * FLASH-OFF PROCESS: After painting, the cabin operates for approximately 15 more minutes to purge residual solvents and thinners. During this phase, fresh air from outside continues to circulate in the cabin. * DRYING PROCESS: In this phase, 80% of the air passing through the cabin is heated to 60 °C and supplied to the cabin via a distributor. As 20% of the solvent is released during drying, these solvents are expelled with the exhaust air. Industrial coatings are typically dried at 60 °C, but the cabin temperature can be adjusted via the control panel as required. * COOLING PROCESS: After the 30-minute drying process, the coil is deactivated via the control panel, the pneumatic damper closes, and the extraction system restarts. During the 5-minute cooling phase, fresh air from outside circulates in the cabin, after which the system stops automatically. ELECTRICAL AND ELECTRONIC EQUIPMENT: These control panels manage the functions and operation of all machinery and devices inside the cabin. The control panel is constructed from durable galvanized sheet metal and steel profiles and is fully enclosed to protect against dust and moisture. Electrical devices and control panels: • The control panel contains essential components such as circuit breakers, fuses, indicator lamps, thermal relays, contactors, and connectors. • Heat-resistant cables are used for command and control lines between the panel and motors or other electrical devices. • Electrical wiring is designed to allow for cabin relocation if necessary. • Operating devices use 380 V 50 Hz, while control devices use 220 V.

Condition: used, Automatic wooden chair painting system, already disassembled and sold in separate pieces: Codpfxsxlb E Aj Afgehc - 3 roller shutter belts, 2.5 metres wide - 3 roller shutter belts, 4 meters wide - 2 painting chains consisting of tracks, chain, towing motor and hangers - spray booths - correspondence desks - various

Year of construction: 2020, condition: new, ROMER® deals with the production of single technological equipment for powder coating plants as well as complete fully automatic turnkey coating plants. ROMER® provides heating solutions for the aero and automotive industries for the largest corporations in the world. We provide warranty and post-warranty service for devices sold by us with a full range of spare parts. the trawl applied to a poorly prepared surface will fall off or corrode after a short period of time. Codjfz Ndyopfx Afgjhc Ensuring the best coating is essentially good degreasing - which is the basis of any painting. The coating of a poorly degreased detail will fall off after a very short time. After degreasing, the next step is to tear down the outer coating of the detail, which improves paint adhesion, e.g. when bending sheet metal, and protection, e.g. with a phosphate layer, which in turn will prolong corrosion resistance. There are many solutions that solve the above issues. What is the most important thing in a powder coating shop? You probably don't have experience with the applicator. Nothing more wrong, even the best applicator will not help you if your oven has bad temperature distributions, in the place where the element is overheated, the paint will discolor and where not heated, the paint will fall off. First of all, the stove is the most important. Oil, gas or electric furnace? You don't know how to power your stove? how is cheaper what does this involve? What are the operating costs? We will try to answer your questions. Depending on the customer's requirements, transport systems can move on the floor or be suspended on poles. - For comfortable solutions for manual installations, we recommend suspended cross traverses (cross transport). - For automated systems, chain conveyors are most often used that do not stop and are a great solution for companies that focus on quality and repeatability of the process. - For companies that make different items at the same time and have e.g. several cabins with different colors, flexible solutions with the use of the power-and-free conveyor are used. This is the most expensive solution.

Year of construction: 2020, condition: new, ROMER® deals with the production of single technological equipment for powder coating plants as well as complete fully automatic turnkey coating plants. ROMER® provides heating solutions for the aero and automotive industries for the largest corporations in the world. We provide warranty and post-warranty service for devices sold by us with a full range of spare parts. the trawl applied to a poorly prepared surface will fall off or corrode after a short period of time. Ensuring the best coating is essentially good degreasing - which is the basis of any painting. The coating of a poorly degreased detail will fall off after a very short time. After degreasing, the next step is to tear down the outer coating of the detail, which improves paint adhesion, e.g. when bending sheet metal, and protection, e.g. with a phosphate layer, which in turn will prolong corrosion resistance. There are many solutions that solve the above issues. What is the most important thing in a powder coating shop? You probably don't have experience with the applicator. Nothing more wrong, even the best applicator will not help you if your oven has bad temperature distributions, in the place where the element is overheated, the paint will discolor and where not heated, the paint will fall off. First of all, the stove is the most important. Codpfx Afjflrc Ssgshc Oil, gas or electric furnace? You don't know how to power your stove? how is cheaper what does this involve? What are the operating costs? We will try to answer your questions. Depending on the customer's requirements, transport systems can move on the floor or be suspended on poles. - For comfortable solutions for manual installations, we recommend suspended cross traverses (cross transport). - For automated systems, chain conveyors are most often used that do not stop and are a great solution for companies that focus on quality and repeatability of the process. - For companies that make different items at the same time and have e.g. several cabins with different colors, flexible solutions with the use of the power-and-free conveyor are used. This is the most expensive solution.

Condition: new, Year of construction: 2025, total height: 4,000 mm, total length: 7,000 mm, total width: 3,000 mm, warranty duration: 24 months, temperature: 80 °C, air demand: 36,000 m³/h, input voltage: 380 V, heating capacity: 345 kW (469.07 HP), power: 40 kW (54.38 HP), fuel: liquid petroleum gas (LPG), energy consumption: 40 kWh, insulation material: Mineralwolle, insulation thickness: 50 mm, nominal power: 345 kW (469.07 HP), Equipment: lighting, MAIN STANDARD Our paint booths are designed to meet all necessary requirements for paint application, including air filtration, extraction, lighting, and a controlled environment. Booth processes are managed via a PLC system, ensuring that desired values are maintained consistently. OPERATING PRINCIPLES OF THE BOOTH The booth’s processes are managed through a control panel, which oversees the following steps: PAINTING PROCESS During painting, 100% fresh air is drawn in from outside and passed through front filters before entering the distribution chamber at ambient temperature. The air is then expelled through the extraction unit. Floor filters (paint stop filters) collect paint particles, and the air passes through final exhaust filters before being discharged. FLASH-OFF PROCESS After painting, the booth continues operating for approximately 15 minutes to purge residual solvents and thinners. During this phase, fresh air circulates from outside into the booth. DRYING PROCESS In this stage, 80% of the air passing through the booth is heated to 60°C and introduced via a distribution system. Since 20% of the solvent is released during drying, it is expelled with the exhaust air. Industrial coatings are typically dried at 60°C, but the booth temperature can be adjusted as needed via the control panel. COOLING PROCESS After the 30-minute drying cycle, the coil is deactivated via the control panel, the pneumatic damper closes, and the extraction system restarts. During the subsequent 5-minute cooling phase, fresh air from outside circulates through the booth, after which the system shuts down automatically. ELECTRICAL AND ELECTRONIC EQUIPMENT Chodpfx Aswzmcbefgjc These control panels govern the functions and operation of machines and devices housed within the booth. The panel is made of durable galvanized sheet and steel profiles and is fully enclosed to protect against dust and moisture. Electrical Equipment and Control Panel: • The control panel contains essential components such as circuit breakers, fuses, indicator lamps, thermal relays, contactors, and connectors. • Heat-resistant cables are used for command and control connections between the control panel and motors or other electrical devices. • Electrical wiring is designed to accommodate booth relocation if needed. • Operating equipment uses 380 V 50 Hz, while control devices operate at 220 V. • The booth’s operation time can be monitored on the electronic control panel, enabling straightforward maintenance scheduling. • Temperature and time settings for booth ventilation (solvent flash-off), intermediate drying, and final drying can be easily adjusted to required values on the digital display of the electronic control panel. • Users can monitor and adjust the drying time using the heating thermostat and time relay.

Year of construction: 2020, condition: new, ROMER® deals with the production of single technological equipment for powder coating plants as well as complete fully automatic turnkey coating plants. Chsdpfx Afofz A H Degec ROMER® provides heating solutions for the aero and automotive industries for the largest corporations in the world. We provide warranty and post-warranty service for devices sold by us with a full range of spare parts. the trawl applied to a poorly prepared surface will fall off or corrode after a short period of time. Ensuring the best coating is essentially good degreasing - which is the basis of any painting. The coating of a poorly degreased detail will fall off after a very short time. After degreasing, the next step is to tear down the outer coating of the detail, which improves paint adhesion, e.g. when bending sheet metal, and protection, e.g. with a phosphate layer, which in turn will prolong corrosion resistance. There are many solutions that solve the above issues. What is the most important thing in a powder coating shop? You probably don't have experience with the applicator. Nothing more wrong, even the best applicator will not help you if your oven has bad temperature distributions, in the place where the element is overheated, the paint will discolor and where not heated, the paint will fall off. First of all, the stove is the most important. Oil, gas or electric furnace? You don't know how to power your stove? how is cheaper what does this involve? What are the operating costs? We will try to answer your questions. Depending on the customer's requirements, transport systems can move on the floor or be suspended on poles. - For comfortable solutions for manual installations, we recommend suspended cross traverses (cross transport). - For automated systems, chain conveyors are most often used that do not stop and are a great solution for companies that focus on quality and repeatability of the process. - For companies that make different items at the same time and have e.g. several cabins with different colors, flexible solutions with the use of the power-and-free conveyor are used. This is the most expensive solution.

Condition: new, Year of construction: 2025, functionality: fully functional, total height: 3,500 mm, total length: 7,050 mm, total width: 4,100 mm, volume flow: 36,000 m³/h, temperature: 80 °C, input voltage: 380 V, heating capacity: 250 kW (339.91 HP), Equipment: cabin, lighting, Paint and Drying Booth It is the centerpiece of your entire painting operation: the combined paint and drying booth. (Alternatively available as a separate paint booth with a dedicated dryer.) Our solutions feature full-surface ceiling filters and, optionally, full-surface floor extraction with drive-over grating or wall extraction at the position of your choice. Chjdpfxexa H Ewj Afgjc If you wish to further increase the efficiency of the system beyond heat recovery and infinitely variable control via frequency converter, we can also offer you a sectional control system. This enables you, for example when doing spot repairs or partial booth loading (such as painting only add-on parts), to activate only the section where the parts are located. This allows you to operate with a reduced air volume, save energy, and minimize costs, all without compromising quality. Feel free to contact us – we would be happy to demonstrate these options in detail. Do you have any questions or suggestions? We are happy to assist you.

Condition: used, Year of construction: 2012, functionality: fully functional, For sale is a complete, fully functional, and automated powder coating line for metal parts, complete with an automated process transport system. This is a ready-made solution for manufacturers of shelving, steel structures, warehouse equipment, and other metal components requiring high-quality paint coatings. Cedpfoz Azx Rex Afgshc The entire system is an integrated process that includes the transport of raw parts, surface preparation, powder coating, curing, and inter-process transport. The price includes: 1. Dismantling and reassembly of the line at a new location, including accommodation and meals for the technicians. 2. New insulation for the joints of the wall and roof panels, the furnace, and the floor. New bolts for the joints. 3. Sealants for the PP tunnel, connection of sections with tubs, and sections with sections.

Condition: used, functionality: unexamined, 3x KREMLIN Airmix paint spraying/material pumps – 1x Type 17A + 2x Type 20-15 – with accessories Description: For sale is a package consisting of three professional KREMLIN Airmix paint spraying/material pumps from a former paint shop. The units were used for professional painting applications and are mounted on mobile or stationary units with corresponding accessories. Scope of supply: 1x KREMLIN Airmix Type 17A - KREMLIN pneumatic Airmix pump - Type plate: 17A - Translation according to type plate: 10:1 - Serial No.: 72989 - with material container - Pressure regulator - Pressure gauge - Hose set - mobile base 2x KREMLIN Airmix Type 20-15 - Type: 20-15 - one unit with visible serial no. 06E 1581 - each with pressure regulators and pressure gauges - Material container Chedpfxoz Iuiqe Afgsc - Material and air hoses - Accessories as shown in the pictures - mounted on mobile units/cabinets The units have not been in operation for a longer period. A current functional test has not been carried out. Due to the prolonged period of inactivity, an inspection, cleaning, and possibly an overhaul of the pumps, seals, and valves should be performed before recommissioning. The units are therefore explicitly offered in their current condition and without testing. Technical documentation is still available for the KREMLIN 20-15; specific spare parts and repair parts such as repair kits and coupling parts are also still offered. Therefore, in addition to recommissioning, the pumps can also be used as a source of spare parts or as a spare parts package for existing KREMLIN Airmix systems. Location: 3608 Thun, Switzerland Availability: immediate Inspection: possible by appointment Sale: preferably as a complete package The sale is ex works, in the current condition, without warranty or guarantee. Subject to prior sale. Selling price: 1,450.00 EUR Price net, any applicable statutory taxes and duties are not included. Export, customs clearance and import duties are the responsibility of the buyer.

Condition: like new (used), Year of construction: 2023, functionality: fully functional, 4 Wagner TWINCONTROL 2k paint application systems, color spraying systems 2 x low-pressure systems, used only once for testing purposes 2 x Airmix systems, little used, in new condition Each system consists of 3 piston pumps: 1 x for the base component 1 x for the hardener component 1 x for flushing with accessories On request, also available with stainless steel storage tanks with agitator, 2 x new, 2 x demonstration units Can also be purchased separately Ideal for series production and automation EX version, as it operates only with compressed air Purchase or lease takeover possible See also document in the appendix (designations) Price description: Two systems always belong together. One system for priming, one system for painting. 1. Twin Control low-pressure (AirCode), either sales price 59,000 euros or lease takeover 1,530 euros/month + 17,000 euros takeover 2. Twin Control high-pressure (Airmix), either sales price 62,000 euros or lease takeover 1,535 euros/month + 19,000 euros takeover Cedpfezk A H Eox Afgohc Lease takeover subject to: Agreement from the leasing company 3. Stainless steel storage tanks (2 new) with agitator, sales price 3,200 euros 4. Stainless steel storage tanks (2 used) with agitator, sales price 2,400 euros If the complete package is taken over, the price is negotiable.

Year of construction: 2020, condition: new, ROMER manipulators are characterized by quiet operation. Bmt7r28v0e They can be widely used both with simple, as well as complex multidimensional processes They are programmed using a PLC controller Working with long and short strokes Chsdpfx Aof Aad Njfgsc The toothed belt transmission ensures quiet operation Maintenance-free AC motor Narrow column design for space saving. The robust construction of the manipulators ensures great possibilities and high stability. The manipulator is equipped with a 7 "touch panel or is externally controlled via the ModBus protocol with RJ45 cables

Condition: good (used), functionality: fully functional, High-pressure piston-diaphragm pump. Universally suitable for aggressive, abrasive, or shear-sensitive products. Very low rinsing agent consumption. For all applications up to 250 bar and 5 l/min. Supplies up to 8 AirCoat spray guns. + 3 automatic AirCoat spray guns with internal control for installation in automated painting systems. +FITTINGS+AIR/PRODUCT HOSE Csdpfjxmf Svox Afgshc

Year of construction: 1993, condition: ready for operation (used), A complete paint shop is available. 1) Sergiani S.p.A. Monomatic S, year of construction: 2001. 2) Finnrose FLT 6, year of construction: 1993. 3,4,5) Three identical Bürkle DAL1-1300 presses, year of construction: 1993. 6) Karl Heesemann FGA 6 EX, year of construction: 1993. 7) Finnrose FLT-4.5, year of construction: 1993. 8) Bürkle DAL2-1300, year of construction: 1985. Hackemack KTR 2040, year of construction: 1996. All machines are part of a paint shop. On-site inspection is possible. Chsdpfxotpp H Es Afgoc

Condition: refurbished (used), Year of construction: 2005, laser type: CO₂ laser, laser power: 100 W, working length: 1,330 mm, working width: 1,630 mm, TECHNICAL DETAILS Working area (L × W): 1,330 × 1,630 mm Laser power: 100 W Laser source: CO₂ Maximum material width: 1,575 mm Material pass-through: 15–50 mm (without material support) Speed: 1 – 1,414 mm/s Maximum acceleration: 14.1 m/s² Codpfoz D E Ddsx Afgshc MACHINE DETAILS Suitable for: Films, acrylic, wood, and textiles Dimensions (L × W × H): 2,730 × 2,450 × 1,590 mm EQUIPMENT i-cut Production Console software package

Condition: new, Year of construction: 2025, warranty duration: 12 months, total width: 1,900 mm, total length: 1,800 mm, total height: 1,550 mm, SPRAY STRIPPING MACHINE – TECHNICAL SPECIFICATION 1. EXTERNAL DIMENSIONS Width: 1 800 mm Length: 1 900 mm Height: 1 600 mm 2. WORKING DIMENSIONS Width: 1 300 mm Length: 1 300 mm Height: 670 mm* 3. TECHNICAL CHARACTERISTICS Total power: 9.2 kW Heating power: 7.0 kW Pump power: 2.2 kW Number of nozzles: 24 Fluid flow rate: 320 l/min Operating pressure: 4.5 bar Operating temperature: 85°C Construction material: AISI 316 (1.4401) acid-resistant stainless steel 4. TANK CAPACITY & HEATING SYSTEM Indirect heating medium: 167 l (±2%) Main tank capacity (stripping fluid): 480 l (±2%) Heating system: indirect heating jacket, separately controlled 5. MACHINE CONSTRUCTION Machine tank equipped with 4 adjustable legs for levelling. Control panel mounted on the machine base. Equipped with an industrial CLICK-CLACK quick-release connector. 6. CONTROL SYSTEM 2 × temperature controllers: One for the heating jacket One for the main processing tank Process time controller LED indicator lights for monitoring correct process operation. 7. DEVICE CAPACITY Suitable for 4–8 rims up to 23”. 8. PLATFORM GRATE Made entirely of acid-resistant stainless steel AISI 316 (1.4401). Serves as a durable, chemically resistant working area for placing rims or other items to be stripped. 9. ROTATING NOZZLE SYSTEM 2 Rotating Arms The machine features two rotating arms, each equipped with a section of the 24 specially engineered nozzles. Nozzles provide multidirectional, high-pressure spraying for fast and uniform paint removal. Designed for maximum coverage, including internal and hard-to-reach areas of the rim. 10. APPLICATION Spray stripping machines represent a modern and highly efficient method of removing paint from alloy wheels. Their use is increasingly appreciated in automotive workshops, tyre services and professional rim refurbishment facilities. Chsdpfx Aeghl Dzefgoc Using this machine significantly improves working comfort by providing perfectly cleaned surfaces, allowing all further service operations to be performed faster and with higher precision. 11. KEY BENEFITS Ideal for rim refurbishment centres, tyre services and automotive workshops. Perfect stripping results thanks to counter-rotating spray nozzles. Extends the service life of other tools and machines due to improved pre-cleaning. Optimises employee working time and increases process efficiency. Ensures consistent, precise and repeatable stripping performance.

Condition: excellent (used), Year of construction: 2001, Complete Parquet painting shop Manufacturer - SORBINI/ VIET Year - 2001 Capacity - 800 m2/shift Cedpferdgrvex Afgohc Time of one cycle - 8 min. Lenght of the line - 42 m

Condition: good (used), Painting booth with suction device and cabinet Article: Spray booth with extraction unit and cabinet Dimensions spray booth: 72 cm wide, 60 cm deep and 80 cm high Cabinet dimensions: 72 cm wide, 109 cm deep and 100 cm high Number of drawers: 6 Colours: green and black Condition: used  Complete factory locker, large selection of storage platforms, pallet racks, shelf racks, paternosters. High quality industrial machines, lathes, grinding machines, hand machines Chsdpfx Afsg I Dhgegec Further articles - new and used - you will find in our shop! International shipping costs on request!