Used Brown Mue44/8A for sale (1,290)

Condition: used, CTS Type: TSS-70/130 Water-cooled cooling unit For sale is a high-quality temperature shock test chamber from CTS (Clima Temperatur Systeme), model TSS-70/130. The device is used for performing temperature shock tests and is typically used in industry, research, and quality assurance. Application areas: Material tests Nodpfxsy Hkd Hj Ab Aedc Aging tests Electronics and component tests Temperature shock and cyclic temperature tests Technical data: Type: TSS-70/130 Test volume: 130 liters Temperature range: Hot chamber: +50°C to +200°C Cold chamber: -80°C to +100°C Heating rate: approx. 6 K/min from room temperature to +180°C Cooling rate: approx. 4 K/min from room temperature to -60°C Temperature deviation: ±1 K in time ±2 K spatially Temperature change rate: max. 100 K/min on average for shock test tests without heat input Temperature adjustment rate: ≤ 15 min in the range of -65°C to +200°C with 10 kg of ICs Cycle time: < 10 seconds Electrical data: Connection: 400 V, 3/N, 50 Hz Rated power: approx. 17.2 kW Rated current: approx. 29 A On-site protection: 32 A slow-blow fuse Connection: Cekon 32 Refrigeration system: Refrigerant: R404A / R23 water-cooled, low-noise, fully hermetic Equipment / Features: CTS control panel Microprocessor-controlled control and monitoring system Program operation up to 100 test programs possible digital setpoint and actual value display RS232 interface 2 free switching channels for on-site control of the test specimen Fault message on potential-free contact Load up to 30 V DC, 2 A EMC tested Technical design: Hot and cold chamber Mobile frame with lifting spindle drive Test chamber / mobile frame made of stainless steel, material no. 1.4301 Insert basket made of stainless steel wire Pipe passage NW 50 with sealing plug Compressed air connection 1/4" AG Condensate drain non-pressurized R 1/2" internal thread Safety door lock lockable door with window Dimensions according to installation diagram: External dimensions approx.: 2335 x 940 x 1820 mm Loading dimension approx.: 1990 x 940 x 1652 mm Test chamber dimensions: height approx. 410 mm Width approx. 480 mm, depth approx. 660 mm Window: 300 x 300 mm Other data: Protection class: IP 22 Sound pressure level: < 60 dB(A) Weight: approx. 950 kg Average consumption during test cycle: approx. 8 kWh For your safety as a buyer, the following information: The following points are carried out on our offered chambers in advance: 1. Functional check and replacement of necessary components 2. If necessary, refill with legally compliant refrigerant 3. Leak test with certificate 4. After successful inspection, the chambers are subjected to a documented test run. Condition: used Scope of delivery: see pictures (Changes and errors in technical data are subject to change!) We will gladly answer any further questions you may have by telephone.

Condition: used, ESPEC Type: PL-3KPH ESPEC Climate Testing Chamber / Environmental Simulation Chamber Model PL-3KPH Air-cooled version For sale is a high-quality ESPEC climate testing chamber for precise temperature and humidity testing in research, development, quality assurance, and industry. The unit is in used condition and can be fully inspected according to the images. The current display shows STOP / ready for operation. Technical data Model: PL-3KPH Test chamber volume: approx. 400 liters Temperature range: -40 °C to +180 °C Temperature change rate (heating): approx. 3.4 K/min Temperature change rate (cooling): approx. 1.7 K/min Temperature stability (-40 °C to +100 °C): ±0.3 K Nsdpfsy H H Iujx Ab Aedc Temperature stability (+100.1 °C to +150 °C): ±0.5 K Temperature stability (+150.1 °C to +180 °C): ±1.0 K Humidity range: 20 to 98 % RH Humidity stability: ±2.5 % RH Internal dimensions (W x H x D): 600 × 850 × 800 mm External dimensions (W x H x D): 1010 × 1690 × 1195 mm Electrical connection: AC 400 V / 3~ / 50 Hz Weight: approx. 350 kg Cooling: air-cooled (no external water connection required) Refrigerant: R404A Equipment / Features Touchscreen control panel Program and constant operation modes BTHC temperature and humidity control Observation window in the door Stainless steel test chamber Internal lighting / Chamber lamp Side cable entry Overheat protection Hour meter integrated Industrial design For your security as a buyer, please note the following information: The following steps are performed on our offered chambers in advance: 1. Functional check and replacement of necessary components 2. If necessary, refill with legally compliant refrigerant 3. Leak test with certificate 4. After successful inspection, the chambers are subjected to a documented test run. Scope of delivery ESPEC Climate Testing Chamber PL-3KPH Scope of delivery as shown in the images Condition & Notes Condition: used Inspection possible by arrangement. Loading with a forklift can be organized. (Subject to changes, prior sale, and errors in the technical data!) If you have any questions, please do not hesitate to contact us.

Condition: used, Weiss Type: WT-1300/70/15 Weiss temperature testing chamber, water-cooled with touch panel control Data for temperature tests: Nedpoza Dv Iefx Ab Ajdc Temperature range: -70 °C to +180 °C Test chamber volume: approx. 1340 liters Temperature change rate: Heating: 15 K/min Cooling: 10 K/min Temperature deviation over time in the center of the usable space: ± 0.1 to ± 0.5 K Temperature homogeneity spatially: ± 0.5 to ± 2 K Test chamber dimensions: Height: 920 mm, Width: 1100 mm, Depth: 1330 mm External dimensions: Height: approx. 2050 mm, Width: approx. 1300 mm, Depth: approx. 3200 mm Permissible test item weight: Total load on the test chamber floor: 150 kg Load per insert shelf: 50 kg Data according to the nameplate: Manufacturer: Weiss Umwelttechnik GmbH Type: WT-1300/70/15 Data for operation: Rated voltage: 3/N/PE AC 400 V ±10% 50 Hz Rated current: 63 A Rated power: 44 kW Refrigerant: R404A: 14.0 kg R23: 5.4 kg Maximum permissible pressures: R404A LP max.: 18 bar R404A HP max.: 25 bar R23 LP max.: 19 bar R23 HP max.: 25 bar Standby pressure: 18.5 bar Equipment: Touch panel control Stainless steel test chamber Multiple insertion levels Side access Heated door seal Water-cooled refrigeration unit CEE connector CE marking available Weight: approx. 1500 kg For the safety of our customers, the following work will be carried out on the offered climate chambers in advance: 1. Functional check and replacement of any necessary components 2. If necessary, refill with legally compliant refrigerant 3. Leak test with certificate 4. Documented test run after successful inspection Condition: used Scope of delivery: (See image) Shipping or freight forwarding possible. Subject to changes, errors and prior sale. We will gladly answer any further questions by telephone.

Condition: used, Weiss Technik Salt spray chamber / corrosion test cabinet Weiss Technik SaltEvent SC 1000 Corrosion test equipment / salt spray test chamber For sale is a used Weiss Technik SaltEvent SC 1000 salt spray chamber. The device is suitable for corrosion tests, salt spray tests, material testing, surface testing, quality assurance, as well as research and development. Technical data Manufacturer: Weiss Technik GmbH Type: SaltEvent SC 1000 Device type: Salt spray chamber / corrosion test equipment Year of manufacture: 2019 Test chamber size: Size 1000 liters Rated voltage: 1/N/PE AC 230 V ±10 % / 50 Hz Rated power: 2.6 kW Rated current: 11.3 A Customer-side fuse: 16 A slow-blow Weight: approx. 370 kg Overall dimensions according to layout drawing: approx. 2910 × 900 × 960 mm Max. test chamber load: 150 kg Floor grid load: 150 kg Insertion rods: 8 kg per rod Shelf for machine part covers: 5 kg Temperature range salt spray test: Ndsdpfszg Er Ajx Ab Asc Ambient temperature +5 K to +50 °C Temperature range condensation test: Ambient temperature +5 K to +42 °C Temperature compressed air humidifier: Ambient temperature +5 K to +70 °C Temperature stability over time: ±1 K Salt solution consumption during salt spray test: approx. 0.5 to 1.5 l/h Equipment S!MPAC control system WEBSeason / color control panel Touch operating panel Test chamber hood Storage tank Control cabinet Floor grid / test chamber grid Compressed air humidifier Hood locking Temperature monitoring Interface Documentation as shown in the pictures Connections / media supply Power connection: 230 V / 50 Hz Compressed air connection available Connection for demineralized water available Exhaust connection available Water drain / condensate drain available Application areas Salt spray test Corrosion test Condensation test Material testing Surface testing Coating testing Automotive Quality assurance Research and development Condition Used Optical condition as shown in the pictures. Scope of supply 1x Weiss Technik SaltEvent SC 1000 salt spray chamber Storage tank Accessories as shown in the pictures Documentation as shown in the pictures The table shown in the photos and any other items not explicitly mentioned are not included in the sale. Inspection possible by appointment. Loading with a forklift is available. Shipping or freight forwarding is possible. Subject to change, errors and prior sale. We will be happy to answer any further questions by telephone.

Condition: used, ESPEC Temperature Shock Chamber ESPEC TSA-72EL-A Temperature Shock Chamber Water-cooled For sale is a used ESPEC temperature shock chamber, model TSA-72EL-A from the manufacturer ESPEC CORP. This chamber is suitable for temperature shock tests, temperature cycling tests, material testing, electronics testing, automotive applications, quality assurance, and research and development. Technical Data Manufacturer: ESPEC CORP. Model: TSA-72EL-A Type of equipment: Temperature Shock Chamber System: 2-zone testing with damper switching Design: Air-cooled Test chamber volume: approx. 72 liters Internal dimensions of test chamber (W × H × D): 410 × 460 × 370 mm External dimensions (W × H × D): 1310 × 1900 × 1470 mm Weight: approx. 900 kg Temperature range, hot chamber: +50 °C to +200 °C Temperature range, cold chamber: -65 °C to 0 °C Temperature stability: ±0.5 °C Preheating temperature: up to +205 °C Pre-cooling temperature: up to -75 °C Heating time: from ambient temperature to +200 °C within approx. 15 minutes Cooling time: from ambient temperature to -70 °C within approx. 40 minutes Temperature recovery condition: +125 °C / 30 min. to -40 °C / 30 min. Temperature recovery time: within approx. 5 minutes Max. test chamber load: 30 kg evenly distributed Cable entry: Ø approx. 50 mm Compressed air supply: 0.4 to 0.7 MPa / 4 to 7 bar Ndjdpfx Aezhkfqjb Asc Refrigerant, high-temperature side: R404A Refrigerant, low-temperature side: R23 Power supply: AC 400 V / 3 phases / 50 Hz Max. current consumption: 45 A Features Color touchscreen control TFT color LCD, 10.4 inches PID temperature control Program memory Trend graphics Alarm history Eco mode Automatic defrost RS-485 interface Over-temperature / under-temperature protection Vertical sliding door Stainless steel test chamber Mechanical cascade refrigeration system Electronic expansion valve Sirocco circulating air fan Damper drive via air cylinder 2 stainless steel test inserts Cable entry, Ø approx. 50 mm Application areas Temperature shock testing Temperature cycling testing Electronics testing Semiconductor testing Automotive Component testing Material testing Quality assurance Research and development Condition Used Optical condition as shown in the images Scope of delivery 1x ESPEC TSA-72EL-A Temperature Shock Chamber 2x Stainless steel test inserts Accessories as shown in the images Important note: For the safety of our customers, the following work will be carried out on the offered climate chambers in advance: 1. Functional check and replacement of necessary components 2. If necessary, refill with legally compliant refrigerant 3. Leak test with certificate 4. Documented test run after successful inspection Inspection possible by appointment. Forklift available for loading. Shipping or freight forwarding possible. Subject to changes, errors and prior sale. We would be happy to answer any further questions by telephone.

Condition: new, STRUERS Grinding and Polishing System Struers LaboPol-30 with LaboForce-100 and LaboDoser-100 Laboratory grinding and polishing system with extensive accessories For sale is an unused, unassembled grinding and polishing system from the manufacturer Struers. The LaboSystem is suitable for reliable and fast manual or semi-automatic grinding and polishing of samples in the laboratory and in production. Technical data: Manufacturer: Struers Type: LaboPol-30 Article number: Type of equipment: Grinding and polishing machine Power connection: 200–240 V / 50–60 Hz Automatic sample mover: Struers LaboForce-100 Article number: Power supply: 1 × 24 V DC Dosing unit: Struers LaboDoser-100 Ndodpfx Aez Srm Njb Aoc Article number: Version for square bottles Grinding and polishing disc: MD-Disc with conical mount Diameter: 300 mm Article number: Sample holder plate: Specimen Mover Plate 6 × 40 mm Article number: Equipment: LaboPol-30 grinding and polishing machine LaboForce-100 sample mover LaboDoser-100 dosing unit MD-Disc carrier disc, 300 mm Specimen Mover Plate, 6 × 40 mm Coupling for sample holder plate Glass desiccator, 250 mm, according to parts list Bottle set Service kit LaboPol-30 MD-Concert storage box Areas of application: Material testing Metallography Sample preparation Grinding and polishing Laboratory applications Quality assurance Research and development Industrial material testing Scope of supply: 1 × Struers LaboPol-30 – Art. No. 1 × Struers LaboForce-100 – Art. No. 1 × MD-Disc, 300 mm – Art. No. 1 × Specimen Mover Plate, 6 × 40 mm – Art. No. 1 × Coupling for sample holder plate – Art. No. 1 × Struers LaboDoser-100 – Art. No. 1 × Glass desiccator, 250 mm – Art. No. DE-720405 1 × Bottle set – Art. No. 1 × Service kit LaboPol-30 – Art. No. 16332999 1 × MD-Concert storage box – Art. No. Condition: New / unused Equipment has not yet been assembled or put into operation Main equipment in original transport packaging Optical condition and accessories as shown in the pictures The system has not yet been assembled and is in storage. Assembly and commissioning are not part of this offer and must be organized independently by the buyer. The image of the fully assembled system is an EXAMPLE IMAGE. The original photos show the actual delivery condition. The workbench shown and other items not explicitly mentioned are not part of the sale. Shipping or freight forwarding is possible. Subject to changes, errors and prior sale. We will be happy to answer any further questions by telephone.

Condition: used, continuous grilling line suitable for: roasting, cooking or browning electric heating 108 kW 3 x 400 V Ndedpsz Udmmsfx Ab Aoc with lower and upper belt : bottom and top grilling overall dimensions (l x w x h) : ± 5.150 x 1.800 x 2.250 mm net length 2.900 mm belt width 600 mm max 265 degrees gap height adjustable adjustable speed pneumatically controlled belt with belt wash system

Condition: used, Leybold Oerlikon Type: RUVAC WSU 501 Leybold Oerlikon RUVAC WSU 501 Roots vacuum pump booster, 505 m³/h, 2.2 kW, DN100 For sale is a powerful industrial vacuum roots pump from the manufacturer Oerlikon Leybold Vacuum. The roots pump serves as a booster pump to increase the pumping speed in vacuum systems and is typically operated together with a backing pump. It is ideally suited for industrial applications such as coating systems, vacuum furnaces, laboratory equipment or general vacuum technology. The pump impresses with its robust design and high pumping capacity. Technical data: Manufacturer: Oerlikon Leybold Vacuum Model: RUVAC WSU 501 Njdjytfzrspfx Ab Aodc Year of manufacture: 12/2010 Pumping capacity: 505 m³/h (50 Hz) / 606 m³/h (60 Hz) Max. pressure difference: 80 mbar Motor power: 2.2 kW Speed: 2900 rpm Voltage: 230 / 400 V three-phase Current draw: approx. 9.0 / 5.2 A Operating mode: S1 continuous operation Important note: "The table shown in the photos is not included in the sale." Condition: used Scope of delivery: (See image) (Changes and errors in the technical data and specifications are subject to change!) We would be happy to answer any further questions you may have by telephone.

Condition: used, KUKA Type: KR 10 R900 sixx / KRC4 KUKA industrial robot complete system Robot: KR 10 R900 sixx Controller: KRC4 including KUKA smartPAD, cable set and accessories For sale is a KUKA industrial robot as a complete system from a commercial inventory. The system is ideally suited for automation tasks in industry, laboratories, assembly, handling, pick-and-place applications, testing tasks, and general robot applications. The 6-axis robot is designed for precise and rapid movements and can be used for gripping, positioning, feeding, moving, and processing components. The system offered consists of a robot arm, KRC4 controller, smartPAD, cables, and other accessories as shown in the pictures. Technical data: Manufacturer: KUKA Roboter GmbH Robot type: KR 10 R900 sixx Article No.: 10016515 Serial number: 500874 Payload: 10 kg Reach: 901 mm Axes: 6 Robot weight: 52 kg Controller: KRC4 Article No.: 11019802 Serial number: 224377 Controller weight: 33 kg Controller connection voltage: 1 x 230 V Mains frequency: 50/60 Hz Full load current: 12 A Mains fuse: 16 A Total system weight (approx.): 90–110 kg Robot dimensions (approx.): Reach 901 mm Controller dimensions (approx.): compact KRC4 design Software / Display according to system: KRC SR version: V8.2.3 HMI version: 8.2.0.4 B22 Nedpfoy Dt D Dox Ab Aedc Base system: KSS 8.2.21_SR Installed options according to display: ExpertTech 3.1.1 Gripper-&-SpotTech 3.0.5 OrangeApps.MqttClient 2.2.12 Profinet KRC-Nexxt 2.2.7 RemoteService 1.0.2 UserTech 3.1.4 Description / Functions: The robot can be used for handling and automation processes, e.g. for gripping, transferring, feeding, positioning or processing workpieces. The 6 axes enable flexible movement in space. The compact design and the reach of 901 mm make the system particularly interesting for confined working areas and automated production cells. Total system weight (including controller and accessories, approx.): 90 – 110 kg Condition: used visually with typical signs of wear the screen and system information can be seen in the photos the visual condition can be seen in the pictures Scope of delivery: (See picture) KUKA KR 10 R900 sixx robot arm KUKA KRC4 controller KUKA smartPAD Connection and linking cables other accessories as shown in the pictures Important: The images are the only basis for the scope of delivery. "The table shown in the photos is not part of the sale." Commercial sale (Changes and errors in the technical data, information are subject to change!) We are happy to answer any further questions you may have by phone.

Condition: used, Thermo Fisher Scientific Nedey D Sqvspfx Ab Ajdc Thermo Fisher Scientific Flash 2000 CHNS O Analyzer with 2 x AI AS 1310 Autosamplers For sale is a used Thermo Fisher Scientific Flash 2000 elemental analyzer. The unit is equipped with two AI AS 1310 autosamplers. It is designed for automated laboratory operation. The system is used for elemental analysis in the laboratory. Sample introduction is performed via the installed autosamplers. This enables continuous and automated operation. Equipment and features: Thermo Fisher Scientific Flash 2000 CHNS O Analyzer 2 x AI AS 1310 Autosamplers Front display with status fields for operating states Gas connections for He and O2 RS232 interfaces and other device interfaces Connections for autosamplers and additional modules Power connection 230 V Accessories and parts as shown in the pictures Technical data: Manufacturer: Thermo Fisher Scientific Model: Flash 2000 Voltage: 230 V AC Frequency: 50-60 Hz Fuse: 2 x 6 A Power: 1400 VA Autosampler: Model: AI AS 1310 Supply: 24 V DC Power: 46 W per unit Serial numbers: 420126446 and 420126487 Dimensions (approx.): Main unit: Width approx. 55 to 60 cm Depth approx. 55 to 65 cm Height approx. 50 to 60 cm Overall width with 2 autosamplers approx. 100 to 120 cm Weight (approx.): Main unit: approx. 45 to 60 kg Autosampler: approx. 8 to 12 kg each Total: approx. 60 to 80 kg Condition: Used, with typical signs of wear and tear due to age and use. The condition corresponds to the pictures. Scope of delivery: Flash 2000 Analyzer 2 x Autosamplers Accessories and cables as shown in the pictures Important note: All information has been provided to the best of our knowledge, based on the pictures, nameplates, and manufacturer information. The table shown in the photos and any other items not explicitly mentioned are not included in the sale. Shipping is possible. Subject to changes, errors and prior sale. We will be happy to answer any further questions by phone.

Condition: used, H. Köhler KG Kesternich Testing Device / Corrosion Test Chamber H. Köhler HK 320 BF Kesternich Testing Device Corrosion test chamber for SO₂ corrosion tests For sale is a used corrosion testing device from the manufacturer H. Köhler KG. The device is used for carrying out Kesternich tests under a sulfur dioxide-containing atmosphere and is suitable for corrosion investigations on materials, surfaces, and coatings. Technical data Manufacturer: H. Köhler KG Type: HK 320 BF Device type: Kesternich testing device / corrosion test chamber Test chamber volume: approx. 300 liters Internal dimensions: approx. 725 x 500 x 750 mm External dimensions: approx. 1070 x 570 x 1970 mm Temperature range: RT +5 °C to 60 °C Expandable to approx. 75 °C according to manufacturer's specifications Power connection: 220 V / 50 Hz Power consumption: 1,000 W Compressed air supply: approx. 4.5 - 8 bar Equipment Stainless steel test chamber Large viewing windows Front door with locking mechanism Test specimen carrier / frames SO₂ gas system Pressure gauge Manual controls Ndsdpfx Aszclxvsb Ajc Base frame with storage area Areas of application Corrosion testing Coating testing Material testing Quality assurance Automotive industry Research and development Condition Used Signs of wear and tear due to age and use Optical condition as shown in the pictures Scope of delivery as shown in the pictures Scope of delivery 1x H. Köhler HK 320 BF Kesternich testing device Accessories as shown in the pictures Shipping is possible. Subject to changes, errors and prior sale. We will be happy to answer any further questions by telephone.

Condition: used, BIO-CIRCLE Type: RWR 80L Auto KST Description: RWR 80 L KST Fully Automatic PLC Parts Washing System The RWR systems from Bio-Circle are the optimal solution for cleaning internal circuit systems without disassembly. The unit is space-saving, quiet, and very easy to operate. Due to the completely closed system, there is no odor nuisance from the cleaner or the dirty water. External dimensions: approx. 1200 x 800 x 1050 mm Power supply: 400 V 50 Hz plug 16A CEE 5p 6h Drain: 1 1/4“ outlet Technical specifications: Type of contamination: Limescale, rust (mineral), oil, grease Quantity of parts: Individual parts, small series, low quantities Component geometry: Complete components (without disassembly) Quality seal: Stainless steel, service package available Maximum filling volume: 80 L Tank material: V2A stainless steel Electrical connection: 400V / 50 Hz Heating: 4.5 kW Flow rate: 25 l/min Temperature (preset): 60 °C Total weight of the cleaning system without tank filling: 180 KG Application area: The RWR 80 L KST Fully Automatic PLC has been developed for the plastics injection molding field Nedpfx Abjzgclms Ajdc and can be used wherever cooling channels (circuit systems, lines) need to be cleaned. Application: Fill the RWR 80 L KST Fully Automatic PLC with Power Cleaner KST 2.0. Once the minimum fill level is reached and the system is switched on, the system will begin to heat up. During the heating period, the system can already be connected to the tool via the two hoses. The 5-stage cleaning program and the change of flow direction run automatically after the instructions displayed on the display have been confirmed. Condition: used Scope of delivery: (See picture) (Changes and errors in the technical data are subject to change!) We will be happy to answer any further questions you may have by phone.

Condition: used, Atlas Xenon Weather-Ometer / Weathering Test Device Atlas Ci3000+ Xenon Weather-Ometer Xenon test device for artificial weathering and light aging For sale is a used Xenon Weather-Ometer from Atlas Material Testing Technology LLC. The device is suitable for weathering tests, light aging, material testing, quality control, research and development, as well as aging tests for plastics, paints, coatings, and materials. Technical data Manufacturer: Atlas Material Testing Technology LLC Type: Ci3000+ Model: Ci3000+ Weather-Ometer Device type: Xenon Weather-Ometer / Weathering Test Device Year of manufacture: 12/2010 Light source: Xenon arc lamp Lamp rated power: 4,500 W Operating range Xenon lamp: 1,700 – 4,500 W Device model according to display: Ci3000+ W Sample sensor 1: Black standard Sample sensor 2: Black panel Light sensor 1: CI 300 – 400 nm Light sensor 2: CI 420 nm Mains connection: 220 / 380 V Frequency: 50 Hz Connection type: 3/N/PE Rated current: 50 A Power consumption: 9.5 kW Control voltage: 24 VDC Ndodpfx Ajzf D Rneb Aoc Compressed air supply required Operating pressure: 80 – 100 PSI (552 – 689 kPa) Compressed air consumption: approx. 4 CFM (0.11 m³/min) Dimensions: approx. 950 x 730 x 1830 mm (W x D x H) Required footprint: approx. 1050 x 2030 mm (W x D) Weight: approx. 404 kg Minimum distance exhaust hood: approx. 102 mm to 152 mm Equipment Touchscreen control panel Xenon burner Test chamber with sample rack Black standard sensor Black panel sensor CI 300 – 400 nm light sensor CI 420 nm light sensor Water-cooled lamp system Exhaust connection Interface connections Integrated humidification system Documentation / Documents as shown in the pictures Accessories / Documents Atlas Weathering Testing Guidebook Atlas Weather-Ometer Auxiliary Filter Lantern Kit Instructions Documentation as shown in the pictures Accessories as shown in the pictures Areas of application Artificial weathering Light aging testing UV and Xenon testing Material testing Plastic testing Paint and coating testing Colors and pigments Textiles Packaging Automotive industry Construction and materials testing Quality assurance Research and development Condition Used Good optical condition Optical condition as shown in the pictures Scope of delivery 1x Atlas Ci3000+ Xenon Weather-Ometer Available accessories as shown in the pictures Available documentation as shown in the pictures The table shown in the photos, as well as any other items not explicitly mentioned, are not included in the sale. Shipping or freight shipping possible. (Changes and errors in the technical data are subject to change!) We would be happy to answer any further questions you may have by phone.

Condition: used, SLM Solutions Type: SLM 280 HL For sale is a professional metal 3D printing system, type SLM 280 2.0, from SLM Solutions (Lübeck). The SLM is designed for 24/7 operation and was last used with titanium. Installation was in 2018. The system already has the sintering walls for gas flow. The system has only been operated with argon for the last 3 years. Approx. 50,000 laser hours. The 50,000 hours refer to the laser on-time; the exposure time is not recorded in the older 280 models. If I disregard the coating time, I estimate approximately 10,000 active laser hours. Last maintenance was in early 2026. Ndsdpfszhlr Eox Ab Aoc Currently, occasional communication issues between the PC and the PLC are observed. In rare cases, this can lead to incorrect status messages, which can cause the system to be briefly interrupted during a running job. Technical data (excerpt) Single laser 400W Weight: 1,245 kg Build volume: 280 × 280 × 365 mm Laser: 1 × 400 W fiber laser (IPG) Optics: 3D galvo system Focus diameter: 80 – 115 µm Max. scanning speed: up to 10 m/s Layer thickness: 20 – 90 µm Minimum feature size: approx. 150 µm Build speed: up to approx. 113 cm³/h (material-dependent) Materials: Stainless steel, tool steel, titanium (Ti64), aluminum, Inconel, CoCr Inert gas: Argon Gas consumption process: approx. 2.5 – 8 l/min Gas consumption purging: approx. 70 – 110 l/min Compressed air: approx. 6 – 7 bar Electrical: 400 V, 3P+N+PE Fuse: 63 A Power consumption: approx. 3.5 – 5.5 kW Machine dimensions: approx. 2600 × 1200 × 2700 mm Weight: approx. 1300 kg (empty), up to approx. 1800 kg (including powder) Important note: "The table shown in the photos is not included in the sale." Condition: used Scope of supply: (See image) SLM 280 machine Control cabinet Process chamber Internal control panel with screen (Changes and errors in the technical data are subject to change!) We will be happy to answer any further questions you may have by telephone.

Condition: used, VETTER Krantechnik PROFI Crane System / Two-Rail Portal Crane VETTER P300 PROFI Crane System Two-rail portal crane with crane bridge, manual travel unit, and electric chain hoist For sale is a used VETTER PROFI crane system from the manufacturer Vetter Krantechnik GmbH. The system is suitable for assembly work, production, mechanical engineering, maintenance, logistics, as well as the safe lifting and positioning of heavy loads. Technical data Manufacturer: Vetter Krantechnik GmbH Type: P300 Design: PROFI Crane System as a two-rail portal with crane bridge Year of manufacture: 2020 Load capacity: 1,600 kg Span of crane bridge: 5,890 mm Support distance L: 5,590 mm Support distance B: 5,890 mm Beam length: 6,390 mm Overall dimensions of the system: approx. 6,590 x 6,590 mm UK crane bridge: 4,145 mm UK portal beam: 4,567 mm Overall height: 4,905 mm Classification according to EN 15011: HC2 / S2 Steel structure: 18/30/30 Operating voltage: 400 V / 50 Hz Control voltage: 24 V Max. permissible hoist weight: 85 kg Electric chain hoist Manufacturer: Vetter Krantechnik GmbH Type: SIXX8AF Year of manufacture: 2020 Load capacity: 1,600 kg Lifting speed: 4.0 / 1.0 m/min Lifting motor power: 1.50 / 0.37 kW Rated current: 7.7 / 5.4 A FEM class: 2m / M5 Protection class: IP55 Duty cycle: 40 % Number of load chains: 2 Weight at 5 m lift: 65 kg Travel unit / Trolley Manufacturer: Vetter Krantechnik GmbH Type: SiCO-HF 2000 A Variant A Load capacity: 2,000 kg Beam width: 66 - 220 mm Weight: 17 kg Equipment Two-rail portal crane system Crane bridge Electric chain hoist SIXX8AF Manual travel unit SiCO-HF 2000 A Load hook Floor control Main switch Conductor rail / Power supply Steel support and beam structure Documentation / Crane test book available Hoist test book available EC declaration of conformity (crane) available EC declaration of conformity (hoist) available Assembly and operating instructions available Accessories as shown in the pictures Application areas Mechanical engineering Assembly work Production Maintenance Workshop operations Material handling Logistics Longest component: approx. 6.4 m Heaviest single component: approx. 300 kg Total weight of the system is approximately between 2,000 and 3,500 kg, depending on the installed steel profiles and foundation plates. Condition Used Optical condition as shown in the pictures System was assembled and in operation Test book and documentation available Scope of delivery VETTER P300 PROFI Crane System Crane bridge Electric chain hoist SIXX8AF 1.6 t Manual travel unit SiCO-HF 2000 A Support and beam structure Control / Operating elements Main switch Documentation / Test book EC declarations of conformity Assembly and operating instructions Accessories according to pictures The machines, tools and other items visible in the pictures, which are not explicitly described, are not included in the scope of delivery. Shipping or freight forwarding is possible. Subject to changes, errors and prior sale. We will be happy to answer any further questions by telephone. Ndedpfezgv U Usx Ab Ajc

Condition: used, Zwick / Roell Material Testing Machine / Universal Testing Machine Zwick / Roell Z020 Allround-Line BT2-FR020TNW.A50 20 kN material testing machine for tensile and compression testing with testControl II & testXpert V3.5 For sale is a used material testing machine from the manufacturer Zwick / Roell. The machine is suitable for tensile and compression tests on metals, plastics, elastomers, composite materials, and numerous other materials in the laboratory, quality assurance, research and development. Technical data: Manufacturer: Zwick / Roell Model series: Z020 Allround-Line Type: BT2-FR020TNW.A50 Testing force: 20 kN Testing direction: Tensile & Compression Testing space height: 1000 mm Crosshead speed: 0.0005–1000 mm/min Power connection: 230 V / 50–60 Hz Power consumption: 8 A Electronics: testControl II Software: Zwick / Roell testXpert V3.5 Equipment: Servo-electric material testing machine testControl II control system Industrial PC with installed testXpert V3.5 software 20 kN Xforce P load cell 2.5 kN Xforce P load cell Testing table Test fixture Various connection and cable sets Accessories as shown in the pictures Dimensions and weight: Machine dimensions (approx.): 1244 × 690 × 1324 mm (W × D × H) Weight: approx. 212 kg Application areas: Tensile testing Nedpfx Aozra Rqjb Aodc Compression testing Material testing Quality assurance Research & Development Testing laboratory Education and training Scope of supply: 1 × Zwick / Roell Z020 Allround-Line material testing machine testControl II control system Industrial PC with installed testXpert V3.5 software 20 kN Xforce P load cell 2.5 kN Xforce P load cell Connection and cable sets Further accessories as shown in the pictures Condition: Used Visual condition as shown in the pictures Functional scope as shown in the pictures Nameplates are present The table, monitor, keyboard, and mouse shown in the photos, as well as any other items not explicitly mentioned, are not part of the sale. Shipping or freight forwarding possible. Subject to change, errors and prior sale. We will be happy to answer any further questions by telephone.

Condition: used, Mitutoyo   Quick Vision Apex QV-X404P1L-C CNC Image Processing Measuring Machine / Optical Measuring System   Manufacturer: Mitutoyo Corporation Type: QV-X404P1L-C Code No.: 363-131EU Professional CNC image measuring system for non-contact dimensional measurement tasks   For sale is a used Mitutoyo Quick Vision Apex CNC image processing measuring machine, including existing PC system, two monitors, control unit, measuring software, and extensive documentation.   The existing PC system and the installed QVPAK software start up. However, the complete machine and measuring function could not be fully tested.   The Quick Vision series is used for non-contact dimensional measurement of workpieces by means of an optical system, image acquisition, and image processing. Suitable for precise measuring and testing tasks, among others, for components from the fields of electronics, precision mechanics, and industrial manufacturing.   Technical data:   Manufacturer: Mitutoyo Corporation Model: Quick Vision Apex Type: QV-X404P1L-C Code No.: 363-131EU Country of Manufacture: Japan Machine type: CNC image processing measuring machine   Measuring range X / Y / Z: approx. 400 × 400 × 250 mm Measuring principle: non-contact optical image measurement CNC-controlled measuring system   Existing measuring software: Mitutoyo QVPAK QVPAK (R): Version 7.502.0010 QVGEO: Version 7.502.0010 Statistics: Version 7.502.0010   Equipment:   Mitutoyo Quick Vision Apex measuring machine PC workstation Nodpfx Aboztyabo Asdc Fujitsu Siemens CELSIUS PC system 2 Fujitsu monitors Keyboard and mouse Mitutoyo control unit / joystick with emergency stop QVPAK measuring software Mitutoyo MCOSMOS / MiCAT data carriers GEOPAK documentation QVPAK documentation Other Mitutoyo operating manuals and documents Clamping plate / workpiece fixture as shown in the pictures Connection cables and accessories as shown in the pictures   Application areas:   Optical dimensional inspection Non-contact workpiece measurement Quality assurance Precision metrology Component and contour inspection Manufacturing and process control   Scope of delivery:   Mitutoyo Quick Vision Apex QV-X404P1L-C with PC workstation, monitors, control unit, existing software, documentation, and accessories as shown in the pictures. Scope of delivery is limited to what is shown in the pictures.   Condition:   Used Optical condition according to pictures PC system and existing QVPAK software start up. Signs of wear and tear due to age and use are present. Visible damage / signs of wear are present on the machine housing, see pictures.   Important note: The machine has not been tested, as it is in a protective mode after being moved. This is also intended by the manufacturer when transporting the machine. The machine must be recommissioned by qualified Mitutoyo personnel.   Shipping by freight forwarder is possible. Subject to changes, errors and prior sale.   We would be happy to answer any further questions by telephone.

Condition: used, H. KÖHLER GmbH Condensation Water Test Device / Corrosion Test Cabinet H. KÖHLER HK 300 S Condensation Water Climate Test Device according to DIN 50 017 For sale is a used condensation water test device from the manufacturer H. Köhler GmbH. The device is suitable for corrosion tests, condensation water climate tests, material testing, coating testing, paint testing, and quality assurance. Technical Data Manufacturer: H. Köhler GmbH Type: HK 300 S Device Type: Condensation Water Test Device / Corrosion Test Cabinet Test Standard: DIN 50 017 Test Chamber Volume: approx. 300 liters Temperature Range: Room temperature to approx. +55 °C Humidity Range: Saturation operation possible Test Chamber Heater: 1,000 W Power Connection: 230 V / 50 Hz Connected Load: 1,000 W Compressed Air Consumption during Ventilation: approx. 3 Nm³/h Compressed Air Connection: 4.5 - 7.0 bar Deionized Water Connection: 2.5 - 4.0 bar Dimensions without Brine Tank: Width: approx. 1,200 mm Depth: approx. 600 mm Height: approx. 1,750 mm Weight: approx. 100 kg Control System HK PC102 Control LCD Display Programmable Test Cycles Condensation Water Climate according to DIN 50 017 Manual Operation / Test Operation Heater 1 / Heater 2 Alarm Display Equipment Stainless Steel Test Chamber Large Glass Door with Seal Test Chamber Thermometer Manometer Ventilation System Compressed Air Connection Deionized Water Connection Drain Connection Stainless Steel Base with Castors Accessories as shown in the pictures Application Areas Condensation Water Testing Corrosion Testing Coating Testing Paint Testing Material Testing Automotive Industry Quality Assurance Research and Development Condition Used Optical Condition as shown in the pictures No documentation available Scope of Delivery H. Köhler HK 300 S Condensation Water Test Device Stainless Steel Base Accessories as shown in the pictures The other items visible in the pictures, which are not explicitly described, are not included in the scope of delivery. Njdpszhadcsfx Ab Aodc Shipping or freight shipping is possible. Subject to changes, errors and prior sale. We will gladly answer any further questions by telephone.

Condition: used, Keysight Mixed Signal Oscilloscope / Digital Storage Oscilloscope Keysight / Agilent InfiniiVision MSO-X 3034A 350 MHz Mixed Signal Oscilloscope with 4 analog channels, 16 digital channels, and 4 GSa/s sampling rate For sale is a used Mixed Signal Oscilloscope from the manufacturer Keysight Technologies / Agilent Technologies. Ndjdpfxjzh I Dws Ab Asc The device is suitable for precise signal and measurement tasks in development, laboratories, service, training, research, as well as industrial electronics and quality assurance. Technical data Manufacturer: Keysight Technologies / Agilent Technologies Type: MSO-X 3034A Series: InfiniiVision Device type: Mixed Signal Oscilloscope / Digital Storage Oscilloscope Bandwidth: 350 MHz Analog channels: 4 Digital channels: 16 Max. sampling rate: 4 GSa/s Display: Color display MegaZoom technology Inputs: 4x analog BNC inputs Digital input / Logic connector USB port USB Device / USB Host Trigger Out Ext. Trigger / Calibration connector Power connection: 100 - 240 V AC 50 / 60 Hz Power consumption: max. 100 W Dimensions: approx. 381 × 204 × 142 mm Weight: approx. 4 kg Features Large color display Front-panel control buttons 4 analog channels 16 digital channels USB interfaces Trigger functions Analysis functions Measurement functions Storage and printing functions Carrying handle Accessories as shown in the pictures Application areas Electronics development Laboratory Service Troubleshooting Signal testing Printed circuit board testing Training Research and development Quality assurance Industrial electronics Scope of delivery Keysight / Agilent InfiniiVision MSO-X 3034A 3x probes as shown in the pictures Power cable Accessories as shown in the pictures Condition Used Optical condition as shown in the pictures Device can be switched on Display and operation appear to be functioning properly Test seals / stickers as shown in the pictures are present Weight: approx. 4 kg The table shown in the photos or other items not explicitly mentioned are not included in the sale. Shipping is possible. Subject to changes, errors and prior sale. We would be happy to answer any further questions by telephone.

Condition: used, GE Druck Modular High-Precision Pressure Controller / Pneumatic Pressure Controller PACE5000 Professional High-Precision Pressure Controller for calibration, pressure testing, automation, and laboratory applications For sale is a used high-precision pressure controller from the manufacturer GE Druck. The PACE5000 is a modular, high-precision pressure control system designed for the most demanding applications in calibration laboratories, research, development, production, and quality assurance. Due to its high control speed and precision, the device is ideally suited for automatic pressure tests, calibration tasks, and industrial measuring and testing systems. Technical data: Manufacturer: GE Druck (Baker Hughes) Model: PACE5000 Device type: Modular High-Precision Pressure Controller Pneumatic Control Module: CM0-B-16G Dimensions: approx. 440 × 88 × 320 mm (W × H × D) Weight: approx. 10.1 kg Control range: -1 to 70 bar(g) Maximum permissible operating pressure (MWP): 94 bar Accuracy: up to 0.001% of the final value (model-dependent) Long-term stability up to 0.001% FV Features: Modular control system Very high pressure control speed Automatic pressure control Pressure testing Leak test function Burst test Switch test Programmable test sequences Nodpoziyqrofx Ab Ajdc User-defined pressure units Display: Color touch display Graphical user interface Display of setpoint and actual value Intuitive menu navigation Interfaces: Ethernet USB Host USB Device RS-232 CAN IEEE-488 (GPIB) 24 V DC inputs/outputs Pneumatic connections: Supply Output Vent Reference G1/8" connection Power connection: 100–230 VAC 50–60 Hz Power consumption: max. 100 VA Application areas: Calibration laboratory Testing systems Quality assurance Automotive industry Aerospace Mechanical engineering Measurement technology Research & Development Automation technology Pressure sensor calibration Equipment: Color display Pneumatic Control Module Ethernet USB RS232 CAN IEEE-488 (GPIB) Pressure connections Power cable Accessories as shown in the pictures Scope of delivery: GE Druck PACE5000 Power cable Accessories as shown in the pictures Weight: approx. 10.1 kg Condition: Used Optical condition as shown in the pictures. Normal signs of wear and tear due to age are present. The table shown in the photos and any other items not explicitly mentioned are not included in the sale. Shipping via parcel service or freight forwarder is possible. Subject to changes, errors, and prior sale. We will be happy to answer any further questions by telephone or e-mail.

Condition: used, IPG Type: Laser welding pliers LSS-5M-3500-3F Ytterbium fiber laser The laser welding pliers LSS5 M complements the series as a compact welding tool. With laser power ranging from one to four kilowatts, integrated cooling technology, and a user-friendly control unit, this combined welding and clamping tool is an ideal tool for welding high-strength steels, galvanized sheet metal pairings, or aluminum. Trifocal technology 3500W laser pliers Controller 3F Operating mode CW/Modulated Wavelength 1070 nm Laser power main beam 3.0 kW Njdpfszd Rinox Ab Aodc Laser power secondary beams 2 × 0.25 kW Spot size (depending on fiber and optics), µm 250 – 600 Power requirement 3500 W laser power Laser duty cycle 30% (with cooler) 3.5 kW Dimensions, controller W × D × H, mm 608 × 808 × 1335 Weight 250 kg Lss-5M-3500-3F 400-460V AC 3P/PE 50/60 Hz 32A/120k Condition: used Scope of delivery: (See picture) (Subject to changes and errors in the technical data, information provided!) We will gladly answer any further questions you may have over the phone.

Condition: new, HAHN-Automation Type: BDE11154003 Resistance welding system The system is designed for the automated resistance welding of the following components: Housing + QLT Ndedpfxezd Rmgo Ab Asc Housing + Heater Service Unit P450 Welding pump + Flange P 800 The system is manually loaded and unloaded by an operator. Any other use of the system than that described above is not intended and is therefore not permitted! System layout Welding unit Sledge unit Cleaning unit for welding electrode Base Linear unit Analysis unit DMC Dimensions (l x w) mm 1700x1200 Cycle time sec. ≤ 30 - 35 Technical availability % ≥ 95 Operator 1 Voltage V 400 AC Frequency Hz 50 Control voltage V 24 DC Fuse A 50 Rated current A approx. 17 Compressed air supply bar 6 Year of manufacture 2020 System components - Control cabinet - Protective enclosure - Linear unit Timing belt axis Festo DGE-25-700-ZR-LKRV Bosch servo motor: MSK030C-0900-NN-M1-UG0-NNNN Gear ratio i=5 Feed constant = 63 mm/rev Reference switch: BES 516-324-G-E5-C-S49 - Sledge unit Balluff BES M08EC-PSC15B-S49G - Evaluation unit DMC: Keyence SR-1000 - Welding unit Spindle axis horizontal Compact module CKK 110-250 without brake Bosch servo motor: MSK030C-0900-NN-M1-UG0-NNNN i=1 p=5mm Integrated reference switch: Hall PNP normally closed Spindle axis vertical Compact module CKK 110-100 with brake Bosch servo motor: MSK030C-0900-NN-M1-UG1-NNNN i=1 p=5mm Integrated reference switch: Hall PNP normally closed Welding tongs Crede PSZ-K Controller: ST-T13V2.0 Power supply: LT-L05-T13V13.0 (5,000A) Water cooler: DLK 1002-C Interface: ProfiNet Proportional control valve block PVB V1.0 Adapter box AB V3.0 for SZ and PSZ Extraction system TBH GmbH GL 265 Z Flow monitor Turck GmbH & Co. KG FCS-M18-AP8X Condition: unused, machine has never been used in production Condition: used Scope of supply: (See image) (Changes and errors in the technical data are subject to change!) We will gladly answer any further questions you may have by telephone.

Condition: used, INSTRON Spring Testing Machine / Universal Testing Machine SPRING SF1392-E1-L12-SPL Professional 100 kN testing machine for spring, compression, and material testing For sale is a used spring testing machine from the manufacturer INSTRON. The system was designed for highly precise spring, compression, and material testing. It is ideal for use in testing laboratories, research and development, quality assurance, and industrial manufacturing. Technical data: Manufacturer: INSTRON Type: SPRING Model: SF1392-E1-L12-SPL Serial number: SPRGK4348 Year of manufacture: 2007 Testing force: 100 kN Power supply: 240 V AC / 1~ / 50–60 Hz Mains current: 25 A Control voltage: 24 V AC / 50–60 Hz Max. ambient temperature: 40 °C Dimensions: Machine (W × D × H): approx. 1,307 × 757 × 2,392 mm Sliding door with 0 mm additional opening space Base Extension Model: 2910-061 Weights: Testing machine: approx. 1,145 kg Base Extension: approx. 96 kg 5800 Controller: approx. 31.8 kg Total weight: approx. 1,273 kg 5500 Controller: Dimensions (H × W × D): 650 × 280 × 570 mm Weight: approx. 31.8 kg Equipment: 100 kN testing frame Protective enclosure with sliding door Base Extension Model 2910-061 Instron 5500 Controller Operating console Industrial PC Monitor Keyboard Mouse Emergency stop system Testing platens / compression tools as shown in the pictures Technical documentation as shown in the pictures Application areas: Spring testing Compression testing Material testing Component testing Load testing Material testing Quality assurance Testing laboratory Research & Development Scope of delivery: Instron SPRING SF1392-E1-L12-SPL Base Extension Model 2910-061 Instron 5500 Controller Operating console Testing platens / compression tools as shown in the pictures Machine accessories as shown in the pictures Technical documentation as shown in the pictures Important note: To operate the system, the original Instron testing software including a valid software license is required. The software and the software license are not included in this offer. According to the manufacturer, a corresponding retrofit is required for recommissioning. A functional test could not be carried out due to the missing software. The sale is therefore preferably aimed at specialist companies for recommissioning or upgrading. Condition: Used Optical condition according to the pictures. Normal signs of wear and tear are present. The workbench shown in the photos is not part of the sale. The operating console and the machine accessories shown are included in the scope of delivery. Transport information: Nodozlp Ixopfx Ab Asdc Original shipping dimensions according to the manufacturer: 2,795 × 1,600 × 1,295 mm (L × W × H) Shipping weight according to the manufacturer: approx. 1,565 kg Loading with a forklift is possible. Shipping via a freight forwarder is possible. Subject to changes, errors and prior sale. We will gladly answer any further questions by telephone or email.

Condition: used, STÄUBLI SCARA industrial robot with CS9 controller TS2-40 4-axis SCARA robot for highly precise pick & place, assembly, and automation tasks For sale is a used SCARA industrial robot from the manufacturer Stäubli, including a CS9 controller and an SP2 teach pendant. The robot system is ideally suited for fast pick & place applications, assembly, packaging, handling, as well as laboratory and automation tasks. The complete system, including controller, teach pendant, robot connection cable, and other accessories, will be delivered as shown in the pictures. Ndsdpfjzlry Rsx Ab Asc Technical data: Manufacturer: Stäubli Faverges SCA, France Model: TS2-40 Robot type: SCARA, 4 axes Year of robot manufacture: 02/2024 Year of controller manufacture: 02/2024 Controller: CS9-TS2-40 Teach pendant: SP2 Reach: 460 mm Rated payload: 2.4 kg Max. payload: 8.4 kg Robot weight: 38 kg Controller weight: 30 kg Repeatability XY: ±0.01 mm Repeatability Z: ±0.004 mm Repeatability Rz: ±0.002° Controller: Stäubli CS9-TS2-40 rack controller SP2 teach pendant VAL 3 activated PROFINET Device Ethernet interface Programmable robot controller Connections: Controller power supply: 1 × 230 VAC, 50/60 Hz Power consumption: 1700 VA PROFINET Device Ethernet Digital input/output Pneumatic connections on the robot Equipment: Stäubli TS2-40 SCARA robot CS9-TS2-40 controller SP2 teach pendant Original robot connection cable End-of-arm tooling mounting installed VAL 3 programming system Accessories as shown in the pictures Application areas: Pick & Place Assembly automation Electronics manufacturing Laboratory automation Packaging automation Machine loading Quality assurance Industry 4.0 applications Scope of delivery: Stäubli TS2-40 SCARA robot CS9-TS2-40 controller SP2 teach pendant Original robot connection cable End-of-arm tooling Accessories as shown in the pictures Condition: Used Year of manufacture 2024. Optical condition as shown in the pictures. System start and information menus tested. Robot system including controller and teach pendant. The table or any other items not explicitly mentioned in the photos are not included in the sale. Shipping via freight forwarder is possible. Subject to changes, errors, and prior sale. We will be happy to answer any further questions by telephone or email.

Condition: used, Universal   Shaker angle adapters / adapter devices   Universal shaker accessories Heavy-duty aluminum angle adapters, clamping devices, and adapter elements for vibration testing systems, vibration tests, and special applications   For sale is a used accessory set for an electrodynamic shaker or vibration testing system.   The set consists of various heavy-duty aluminum angle adapters, adapter plates, clamping devices, clamping blocks, and other accessories. Ideal for test specimen mounting, special designs, and vibration tests.   Technical data:   Manufacturer: unknown Type: Accessory set for electrodynamic shaker / vibration testing system Material: predominantly aluminum Design: angle adapters, adapter plates, clamping devices, and fasteners   Components: Several heavy-duty angle adapters Adapter plates of various sizes Clamping and tightening devices Clamping blocks and adapter elements Fastening materials and other accessories as shown in the pictures   Features:   Heavy-duty aluminum construction Threaded and clearance holes Universally applicable Angle adapters for test specimen mounting Adapter plates Clamping and tightening devices Accessories as shown in the pictures   Application areas:   Electrodynamic shakers Vibration testing systems Vibration testing Material testing Environmental simulation Research and development Automotive industry Test specimen mounting and special designs   Scope of supply:   Complete accessory set as shown in the pictures Angle adapters Adapter plates Clamping devices Clamping blocks Fastening materials Other accessories as shown in the pictures   Weight: 600 kg   Condition:   Used Visual condition as shown in the pictures. Normal signs of wear and tear, scratches, and pressure marks are present.   Only the accessories shown in the pictures are sold.   The table shown in the pictures or other items not explicitly mentioned are not included in the sale.   Shipping on a pallet or collection is possible. Njdpfszpx Ucox Ab Asdc Subject to changes, errors, and prior sale.   We will be happy to answer any further questions by telephone.