Screw Compressor SCC SMART 7

Condition: used, Year of construction: 2010, machine/vehicle number: 1000017741, inner dimension length: 1,000 mm, inner dimension width: 840 mm, inner dimension height: 815 mm, operating temperature: 1,700 °C, usable tank capacity: 685 l, No minimum price – guaranteed sale to the highest bidder! The machine was professionally dismantled and stored. All parts and connections are labeled for reassembly. An on-site inspection is possible at any time. TECHNICAL DETAILS Furnace chamber and usable space Usable batch space (W × H × L): 840 × 815 × 1,000 mm Total length of the graphite box: approx. 1,100 mm Usable volume: approx. 685 l Operating temperature: max. 1,700 °C Operating temperature under partial pressure: max. 1,500 °C Operating temperature under vacuum: max. 1,700 °C Temperature uniformity: ± 10 K Temperature fluctuation in the steady state: ± 5 K MACHINE DETAILS Process pressure range: 1 × 10⁻² < p < 1,040 mbar Final pressure in the empty, clean, and cold furnace: < 1 × 10⁻² mbar Leak rate: < 5 × 10⁻³ mbar·l/s Power supply: 3 × 400 V, 50 Hz Permissible voltage fluctuation: max. ± 5 % Installed heating power: max. approx. 190 kW Electrical power of the pump station: approx. 14 kW Cooling water flow rate: approx. 150 l/min Cooling water temperature: 20–30 °C Cooling water pressure: 2–4 bar Cooling water quality requirements: according to specification PW 800 943 ND Compressed air for valve operation: 4–5 bar Nitrogen inlet pressure: 5–7 bar Hydrogen inlet pressure: 5–7 bar EQUIPMENT Double-walled furnace chamber made of stainless steel with water cooling Internal graphite box for precise guidance of the process gases Post-cleaned graphite components Automatic control of the entire process Pump station Lajdpfx Aljz I Tt Ijbeh Labeled lines and connections for easier recommissioning Note: Two internal graphite heating elements were damaged during dismantling and must be replaced.

Condition: used, TECHNICAL DETAILS - Number of axes : 5 MILLING SPINDLE - Tool holder type : HSK63 - Spindle speeds : 18000 [rpm] - Spindle power : 25 [kW] LINEAR AXES - Travels on X/Y/Z axes : 760 / 510 / 520 [mm] - Rapid traverses rates (X/Y/Z) : 45 / 45 / 40 [mm/min] A ROTARY AXIS - Travel : -110 / +30 [°] - C ROTARY AXIS - Travel : 360 [°] - Rapid traverse rate : 25 [rpm] TOOL CHANGER - Auto. Tool Changer type : Bras chargeur - Tool magazine capacity : 40 TABLE - Table dimensions : Ø248 [mm] - Maximum weight upon table : 200 [kg] POWER SUPPLY - Supply voltage : 400 [V] - Total installed power : 48 [kVA] WEIGHT & DIMENSIONS - Machine floor space : 3.940 x 4.060 [mm] - Machine height : 2.865 [mm] - Machine weight : 6000 [kg] EQUIPMENT - CNC : Hurco WinMax / MAX5 - Interactive programming - Electronic handwheel - Coolant tank Laedpfsy Tzctjx Albjh * with high-pressure pump - Coolant through spindle - Chips conveyor - Spindle cooling unit

Condition: ready for operation (used), Year of construction: 2018, operating hours: 13,270 h, laser type: fiber laser, laser power: 4,000 W, sheet thickness (max.): 20 mm, overall weight: 9,700 kg, year of last overhaul: 2025, The system must be dismantled between November 20, 2026, and November 22, 2026! TECHNICAL DETAILS Laser type: Fiber laser Laser power: 4,000 W Sheet metal thickness (max.): 20 mm Sheet metal thickness steel (max.): 20 mm Sheet metal thickness stainless steel (max.): 20 mm Sheet metal thickness aluminum (max.): 20 mm MACHINE DETAILS Control type: CNC control Automation level: Automatic Actuation type: Electric Power: 4 kW (5.44 hp) Input voltage: 400 V Input frequency: 50 Hz Type of cooling: Water Compressed air connection: 7 bar Laser operating hours: 13,270 h Year of last overhaul: 2025 Dimensions & Weight Dimensions (L x W x H): 9,310 x 7,813 x 2,300 mm Total weight: 9,700 kg EQUIPMENT CE marking Lajdpjz I S Uwefx Alboh Central lubrication system Cooling unit Documentation/Manual Dust extraction Emergency stop switch Fume extraction Safety light curtain

Condition: excellent (used), Year of construction: 2021, operating hours: 4,689 h, functionality: fully functional, machine/vehicle number: 103, overall weight: 32,000 kg, power: 390 kW (530.25 HP), conveyor belt speed: 2,000 mm/s, fuel tank capacity: 950 l, The machine is equipped with a new roller! The following work was carried out on the machine: Machine washed and cleaned Roller disassembled and bearing shield separated from the roller Rack, limiter, and comb attachments disassembled Cooling and air intake system, front door, and soundproofing register disassembled and reassembled Roofs disassembled and reassembled Various brackets repaired and re-welded Oil pan replaced Exhaust system completed Openings in the housing retrofitted with labyrinth sealing New tools mounted on the drum and rack Roller mounted Cable harnesses repaired TECHNICAL DETAILS Type: Size L-C3 VARIOMAT Roller teeth: 42 pieces Limiter: Size L, 20 pieces Roller: New Loading height: 3,307 mm Loading protection: On both sides Longitudinal belt length: 4,450 mm Longitudinal belt width: 1,000 mm Rear belt length: 8,500 mm Rear belt width: 1,200 mm Discharge height: 5,050 mm Conveyor speed: 2 m/s MACHINE DETAILS Engine type: Diesel-hydraulic Engine: MTU 6R1300 Rated power: 390 kW Engine speed: 1,700 rpm Emission standard: EU Stage V Fuel tank: 950 l Additional hydraulic connection: 30 l/min Additional hydraulic connection: 70 l/min Roller drive: 380 kW Drive system: VARIO Hydraulic system: Load-Sensing system Operating hours: 4,689 h Chassis: 3-axle semi-trailer chassis unit Drive: Hydraulic Dimensions & Weight Lajdpfjz Rqcmox Albsh Dimensions in working position (L x W x H): 16,786 x 2,500 x 5,050 mm Dimensions in transport (L x W x H): 9,971 x 2,500 x 3,893 mm Total weight: 32,000 kg Operating hours: 4,689 h EQUIPMENT Basic package Inventhor Type 9 Additional hydraulic connection 30 l/min and 70 l/min Roller drive via planetary gear 380 kW Load-Sensing system Radio remote control, complete Large side GRP maintenance doors easy-to-maintain engine compartment with LED light hydraulically reversible fan wheel loading protection on both sides Fire extinguisher Maintenance ladder Toolbox acoustic start-up warning Doppstadt telematics system 3-axle semi-trailer chassis unit Shredding system Size "L-C3"-VARIOMAT Size "L" - "Limiter" (20 pieces) hydraulic drive Watering on both sides Rear belt 8.5 m, 1,200 mm wide Overbelt magnet neodymium Frame for overbelt magnet neodymium Central lubrication with pump LED lighting package engine compartment and rear Note: The Doppbasket system can be retrofitted for an additional cost.

Year of construction: 1996, condition: ready for operation (used), travel distance X-axis: 3,500 mm, travel distance Y-axis: 2,000 mm, travel distance Z-axis: 1,250 mm, controller manufacturer: HEIDENHAIN, controller model: TNC 426, spindle speed (max.): 2,500 rpm, number of axes: 5, This 5-axis TOS WHN 13.8 boring machine was manufactured in 1996. It features a working spindle diameter of 130 mm, X-axis travel of 3500 mm, Y-axis travel of 2000 mm, and a Z-axis travel of 1250 mm. The rotary table clamping surface measures 2200 x 1800 mm, supporting a maximum workpiece weight of 12,000 kg. If you are looking to get high-quality boring capabilities, consider the TOS WHN 13.8 machine we have for sale. Contact us for more information. Lsdpfx Aeyar D Hslboah Machine Benefits Technical Machine Benefits • Rotary table clamping surface: 2200 x 1800 mm Extra Information Working spindle diameter: 130 mm Technical Specification Taper Size ISO 50

Condition: ready for operation (used), functionality: fully functional, TECHNICAL DETAILS Drive power: 15 kW EQUIPMENT Control system Suitable for secondary shredding Lodpfx Alsz Ngbvsbsah The seller has a suitable conveyor belt in stock as an optional extra.

Condition: ready for operation (used), functionality: fully functional, screw diameter: 200 mm, Granulation of temperature- and shear-sensitive plastics Suitable for soft PVC Suitable for rigid PVC Suitable for HFFR formulations Suitable for elastomer compounds for low-, medium-, and high-voltage cables TECHNICAL DETAILS Screw diameter: 200 mm Length from feed inlet to end: approx. 1,100 mm L/D ratio: approx. 5.5 : 1 MACHINE DETAILS Laedpfxez Ngaxo Albeh Drive power: 72.5 kW Overall machine length: approx. 2,500 mm Feed inlet height: approx. 1,000 mm EQUIPMENT Eccentric granulation EGR Degassing zone Can be used as a single-screw extruder for various processing applications

Condition: used, Year of construction: 2014, Milling machines Travel distance X: 1067 mm Travel distance Y :610 mm Travel distance Z: 610 mm HSC-machines Number of axis: 3 milling machine / machining center spindle revolutions: 12000 rpm Laodpfozguhyox Alboh table size X: 1270 mm table size Y: 610 mm input Power : 12 kW Torque: 237 Nm High-performance 3-axis machining center Number of tools in the magazine: 30 SK40 tool holder Internal coolant supply Spindle cooler

Condition: ready for operation (used), functionality: fully functional, No minimum price – guaranteed sale to the highest bidder! TECHNICAL DETAILS Load capacity: 2,500 kg Lifting height: 6,430 mm Mast type: Triplex mast Full free lift: available Fork length: 1,200 mm Hydraulic functions: 3rd valve and 4th valve Side shifter: available Hydraulically adjustable forks: available MACHINE DETAILS Manufacturer: Linde Type: E25 Year of manufacture: 2019 Drive type: Electric Battery type: Lithium-ion Battery year of manufacture: Battery voltage: 90 V Battery capacity: 268 Ah Measured idle voltage: 97.4 V Operating hours: 12,011 h Own weight: 5,200 kg Overall length: 3,700 mm Overall width: 1,200 mm Overall height: 2,824 mm Service valid until: UVV (Technical Inspection Association) valid until: EQUIPMENT EVO facelift model Former Linde full-service unit Hydraulic double pallet clamp Full cabin Lodpfx Aoz R Tpkjlboah Heater Windshield wiper White, non-marking tires LED work light front LED work light rear Road traffic lighting with turn signals Orange warning light Safety Light front Safety Light rear Front camera Comfort seat All dimensions are approximate. No warranty is given for typing or measurement errors. Collection conditions: Side loading up to 6 tons with a large forklift on site is possible. Loading is at your own risk. Rear loading via ramp possible with a truck height of 100–150 cm, up to 15 tons and up to a width of 230 cm. Collection is only possible after receipt of payment confirmation by email. Collection without prior notification is possible from Monday to Friday between 07:00 and 16:00. If the machine is not collected on time, a storage fee of €20 per machine and day will be charged. Outstanding storage fees must be paid in full before collection. Lot number: 639

Condition: ready for operation (used), functionality: fully functional, No minimum price – guaranteed sale to the highest bidder! TECHNICAL DETAILS Electrical data Battery voltage: 80 V Charging current: 140 A Suitable battery capacity: 800–1,000 Ah Mains connection: 400 V / 16 A Battery connection: REMA 320 A MACHINE DETAILS Manufacturer: TCE Type: 80 V 140 A Year of manufacture: 2026 Condition: New and unused, in original packaging Length: 600 mm Width: 600 mm Height: 600 mm Weight: 70 kg EQUIPMENT 400 V / 16 A mains connection REMA 320 A plug All dimensions are approximate. No guarantee is given for typographical or measurement errors. Collection conditions: Side loading up to 6 tons with a large forklift truck available on site is possible. Loading is at your own risk. Ljdoz R Sg Ijpfx Albeah Rear loading via ramp is possible with a truck height of 100–150 cm, up to 15 tons, and up to a width of 230 cm. Collection is only possible after receipt of payment confirmation by email. Collection without prior notification is possible from Monday to Friday between 07:00 and 16:00. In the event of delayed collection, a storage fee of €20 per machine per day will be charged. Outstanding storage fees must be paid in full before collection. Lot number: 8040

Condition: ready for operation (used), Year of construction: 2016, travel distance X-axis: 661 mm, travel distance Y-axis: 407 mm, travel distance Z-axis: 508 mm, table load: 1,500 kg, spindle speed (max.): 10,000 rpm, spindle motor power: 11,000 W, number of slots in tool magazine: 24, tool weight: 7,000 g, number of axes: 3, This 3-axis Hurco VM10i was manufactured in 2016. It features an X-axis travel of 661 mm, Y-axis travel of 407 mm, and Z-axis travel of 508 mm. The machine includes a robust table size of 762 x 406 mm and a maximum table load of 1,500 kg. If you are looking to get high-quality machining capabilities, consider the Hurco VM10i vertical machining centre we have for sale. Contact us for further details. • CNC Control: HURCO MAX 5 (WinMax software version V10.01.131.12) • Table Dimensions: 762 x 406 mm • T-Slots: 3 x 18 mm • T-Slot Center Distance: 10 mm • Spindle Nose to Table Distance: 102 - 610 mm • Spindle Torque: 72 Nm • Rapid Traverse (X/Y/Z): 28,000 mm/min • Tool Magazine Capacity: 24 positions • Maximum Tool Diameter (Adjacent Occupied): 80 mm • Maximum Tool Diameter (Adjacent Empty): 120 mm • Maximum Tool Length: 250 mm • Machine Working Hours: 15,420 h 10 min • Spindle Hours: 2,727 h 59 min • Monitor: 19" Touch Screen • Hardware: 128 GB SSD, 4 GB RAM, Dual-Core 2.7 GHz Processor • Connectivity: 2x USB 2.0 (console), 2x USB (electrical cabinet), 1x Ethernet LAN Additional equipment • Remote electronic handwheel • Auger-type chip conveyor • Wash gun (water/air) • Status tower lamp • Retention knobs • Leveling pads Technical Specification Taper Size ISO 40 Lodpfxozgf Hto Albeah

Condition: ready for operation (used), functionality: fully functional, No minimum price – guaranteed sale to the highest bidder! TECHNICAL DETAILS Charging voltage: 80 V Charging current: 120 A Lasdpfx Alsz R Sguebeh Suitable battery capacity: 600–900 Ah MACHINE DETAILS Year of manufacture: 2026 Mains connection: 400 V / 16 A Dimensions (L × W × H): 600 × 600 × 600 mm Weight: 70 kg EQUIPMENT Rema connector: 320 A Original packaging All dimensions are approximate. No guarantee is given for typographical or measurement errors. Collection conditions: * Side loading up to 6 tonnes is possible with a large forklift truck on site. Loading is at your own risk. * Rear loading via ramp is possible with a truck height of 100–150 cm, up to 15 tonnes and up to a width of 230 cm. * Collection is only possible after receipt of the payment confirmation by email. * Collection without prior notification is possible from Monday to Friday between 07:00 and 16:00. * In case of delayed collection, a storage fee of €20 per machine and day will be charged. Any outstanding storage fees must be paid in full before collection. Lot number: 8020

Condition: ready for operation (used), functionality: fully functional, No minimum price – guaranteed sale to the highest bidder! TECHNICAL DETAILS Battery voltage: 80 V Charging current: 100 A Suitable battery capacity: 500–700 Ah Mains connection: 400 V / 16 A Battery connector: REMA 160 A MACHINE DETAILS Manufacturer: TCE Type: 80 V 100 A Year of manufacture: 2026 Condition: New and unused Dimensions (L × W × H): 600 × 600 × 600 mm Weight: 70 kg EQUIPMENT Original packaging 400 V, 16 A mains plug REMA 160 A battery connector All dimensions are approximate. No guarantee is given for typographical or measurement errors. Collection conditions: * Side loading up to 6 t is possible with a large forklift on site. Loading is done at your own risk. Ljdpfxsz R Sgns Alboah * Rear loading via ramp is possible for truck heights of 100–150 cm, up to 15 t, and up to a width of 230 cm. * Collection is only possible after receipt of the payment confirmation by email. * Collection without prior notification is possible from Monday to Friday between 07:00 and 16:00. * A storage fee of €20 per machine per day will be charged for late collection. Outstanding storage fees must be paid in full before collection. Lot number: 8011

Condition: ready for operation (used), Year of construction: 2015, operating hours: 9,000 h, travel distance X-axis: 610 mm, travel distance Y-axis: 508 mm, travel distance Z-axis: 610 mm, controller manufacturer: HURCO, controller model: WinMax / MAX5, table width: 508 mm, table length: 760 mm, table load: 1,500 kg, spindle speed (max.): 12,000 rpm, spindle motor power: 9,000 W, number of slots in tool magazine: 30, number of axes: 3, This 3-axis Hurco VMX 24i was manufactured in 2015. It features an X-axis travel of 610 mm, Y-axis travel of 508 mm, and Z-axis travel of 610 mm. The machine includes a robust table size of 760 x 508 mm and a maximum table load of 1,500 kg. If you are looking to get high-quality machining capabilities, consider the Hurco VMX 24i vertical machining centre we have for sale. Contact us for further details. - Tool Holder: SK40 / CAT40- Max. Torque: 95 Nm- Max. Tool Diameter: 80 mm- Max. Tool Length: 300 mm- Max. Tool Weight: 7 kg- Rapid Traverse X/Y: 38 m/min- Rapid Traverse Z: 32 m/min- Additional Equipment: Automatic centralized lubrication, Chip flushing system, Scraper belt conveyor, Coolant unit, Electronic handwheel, Network connection- Included in Delivery: CNC milling machine Hurco VMX 24i- Excluded Items: Vise, tools, clamping devices, other accessories Lsdpfezc Rziox Alboah

Condition: ready for operation (used), functionality: fully functional, No minimum price – guaranteed sale to the highest bidder! TECHNICAL DETAILS Output voltage: 48 V Charging current: 50 A Suitable battery capacity: 300–500 Ah Maximum battery capacity: 800 Ah (?) Protection class: IP66 Mains connection: 220 V Connector type, battery side: Rema, 160 A Impact protection: available MACHINE DETAILS Year of manufacture: 2026 Overall length: 300 mm Overall width: 200 mm Overall height: 200 mm Weight: 10 kg EQUIPMENT 220 V mains plug Rema connector, 160 A All dimensions are approximate values. No guarantee is given for typographical or measurement errors. Laodpez R Sf Rofx Albsh Collection conditions: * Side loading up to 6 tons is possible with a large forklift on site. Loading is at your own risk. * Rear loading via ramp is possible for truck heights of 100–150 cm, up to 15 tons, and up to a width of 230 cm. * Collection is only possible after receipt of payment confirmation by email. * Collection without prior notification is possible from Monday to Friday between 07:00 and 16:00. * If collection is not carried out within the specified timeframe, a storage fee of €20 per machine per day will be charged. Any outstanding storage fees must be paid in full before collection. Lot number: 4850