Bale press

HSM 4809

Condition: ready for operation (used), Hsm HL 4809 LI baler - Large filling opening, ideal for big boxes Cpsdpfsra Dddox Aa Esw - Container tipper for convenient filling Pressing force in kN: 480 - Voltage/frequency: 3 x 400 V / 50 Hz - Bale weight in kg (depending on material): up to 400 kg - Bale dimensions (length x width x height in mm): 1200 x 1100 x 750 - Machine dimensions (length x width x height in mm): 5648 x 1849 x 2515 Idle cycle time in seconds: 53 - Manual tying: 4 times with wire

Condition: good (used), Year of construction: 2009, functionality: fully functional, Weight 4950 kg, total weight 12000 kg Cpsdpjwpmckjfx Aa Ejw 5.5 kW

Condition: not inspected (used), Year of construction: 1985, functionality: fully functional, pressing force: 50 t, bale length: 1,000 mm, bale width: 750 mm, bale height: 750,750,750 mm, bale weight: 500 kg, input voltage: 400 V, overall weight: 7,500 kg, oil tank capacity: 500 l, power: 30 kW (40.79 HP), empty load weight: 7,500 kg, input frequency: 50 Hz, Manufacturer: Paal Typ: Pacomat V Year of construction: 1985 Press power main press: 50 t Specific press capacity: 5 kg/cm² Feed channel: 1.000 x 720mm (l x w) Theoretic throughput rate: 200 cbm/h Bale size: 700 x 1.000 mm (w x h) length adjustable Driving motor: 30 kW Bale weight: approx. 500 kg Cpjdpoic Rl Defx Aa Eow Machine weight: approx. 8t The hydraulic unit is functional, the drive motor is in the removed state.

Condition: excellent (used), Year of construction: 2006, operating hours: 2,632 h, functionality: fully functional, machine/vehicle number: 29.381, pressing force: 35 t, filling opening width: 620 mm, filling opening length: 1,000 mm, total width: 2,380 mm, total height: 2,500 mm, total length: 6,625 mm, Including feed belt. The machine is immediately ready for operation. Csdpfx Aaovaw T As Eopw

Condition: new, Year of construction: 2025, pressing force: 38 t, power: 5.5 kW (7.48 HP), New on stock Avermann MPC 20 PEL Cjdjwhfu Aepfx Aa Ejpw Optional with Bin Lift

Condition: good (used), Year of construction: 1973, Waste compactor, waste compactor, compactor container, waste container, self-compacting container, mobile waste compactor, paper compactor container, paper container -Stationary press for: interchangeable containers -Load chute: covered -Pressing process: hydraulic -Pressing process: automatic -Emergency safety switch: at the deposit slot -Piston dimensions: 1450 x 650 mm -Piston stroke: 1100 mm -Transport dimensions: 2100 x 4500 mm -side threaded ratchets for skip containers -Functionally tested Csdpsb A Ii Ssfx Aa Eopw

Condition: ready for operation (used), Baler Hsm vk 42/1200 fully automatic Pressure force: 42 tons Beam dimensions: 700 x 800 x 600 - 1200 mm Beam weight: approx. 450 kg Press length approx. 7 meters press weight approx. 6000 kg tying 4 x wire automatically Cpodera Nrxepfx Aa Ejw

Condition: excellent (used), Year of construction: 2006, Balemaster Year: 2006 Type: CMG 268 Csdpfx Aordwlkoa Eopw Waste compactor

Condition: reconditioned (used), Year of construction: 2007, operating hours: 22,605 h, functionality: fully functional, pressing force: 100 t, filling opening width: 1,100 mm, filling opening length: 1,600 mm, bale width: 1,100 mm, bale height: 1,100 mm, bale weight: 1,400 kg, input current: 238 A, overall weight: 36,000 kg, oil tank capacity: 1,300 l, For sale is a overhauled baler, with 100 tonnes pressing force, large format 1100 x 1100 mm, 75 kW drive power and 10-fold cross binding Technical data baler: Manufacturer Bollegraaf Typ HBC 110 K / 75 kW Year of construction 2007 Press power main press 100 tons Press power of pre-press 50 tons Operating hours 22,605 hours Feed channel 1,600 x 1,100 mm Capacity per cycle time 3,15 m³ Theoretic cycle time 19 sec. Bale size 1,100 x 1,100 mm Driving motor 75 kW Connected load 126 kW Full load current 238 A Tying system 5-fold vertical, 5-fold horizontal, fully automated Throughput rate at a bulk weight of 30 kg/cbm approx.16 tons/h bulk weight of 50 kg/cbm approx. 25 tons/h bulk weight of 100 kg/cbm approx. 47 tons/h Bale weight up to 1400 kg, depends on material and bale lenght Volume oil tank approx. 1,300 l SPS controller Telemecanique TSX Micro Operating panel Schneider MAGELIS Touch Baler dimensions built up with hopper 11,750 x 5,000 x 7,105 mm (l x w x h) Transport dimensions only baler 11.750 x 2.500 x 3.450 mm (l x w x h) Machine weight baler approx. 36 tons Comments: The press was partially overhauled and serviced in our workshop and tested and stored after completion of the work. The machine is available at short notice and can be inspected in our warehouse by appointment. The following overhaul work was carried out: Rust removal and partial painting of the press. Remaining hydraulic oil tank drained, oil filter and air filter replaced. New hydraulic oil topped up. All hydraulic hoses replaced. Main hydraulic cylinder, two cylinders of the prepress flap and the cylinder of the press channel dismantled, disassembled, checked, cylinder tubes honed, all seal sets replaced and a final pressure test carried out. Cpedpjvf E Avsfx Aa Esw Disassembly of the prepress flap with bearings and bearing blocks. 1st and 3rd circular arc segmet cut out and a new one welded in again. Both bearings of the shaft of the prepress flap replaced. Upper material deflector on the frame of the prepress flap replaced. Press ram dismantled, checked and both front rollers replaced. Material deflectors and wear profiles on the sides and base of the press ram cut off and new ones welded in. Horizontal and vertical needle and tying unit dismantled, disassembled, checked, plastic sliding plates, bearings of the drill shafts and wire deflection rollers with bearings in the needle heads replaced. Both bronze slide rails on the left and right in the frame cover to the press ram replaced. Both wire deflection units on the left and right, with bale retaining clamps, completely renewed. Wire insertion unit including hydraulic cylinder under the needle feedthroughs completely renewed. Wire entry marks in the floor and side walls of the bale chamber welded shut and smoothed. General maintenance and service work carried out in accordance with the manufacturer's specifications. Press was tested in manual and automatic mode, accepted and stored after completion of overhaul work. We accept no liability for the technical specifications or any errors.

Year of construction: 2022, condition: new, Complete solution for transporting bulk goods such as wood chips, wood pellets, shredded goods, granulate, etc. Aluminum angled conveyor incl. substructure horizontal range 2,500mm (adjustable) Rising range 4,000mm (customizable) Angle in the bend freely adjustable Feed height: horizontal (individual) Discharge height individually adjustable Construction: height adjustable ( to move) Conveyor belt width 600mm (customizable) We supply our conveyor belts in PVC, PU, ​​felt or rubber. PU conveyor belt including cleats and corrugated edge Drive: Motor 1.1KW (adjustable), speed approx. 0.3m/sec Connection 220/240V, 50Hz protection class IP54 Drive etc. ready for connection, motor control optional 8x adjustable machine feet for alignment Wavy edge: 50x30mm T-40 lugs - 300mm pitch 2-layer particularly laterally stable We always have various systems of this type in stock. The delivery time for an individual system is currently around 2-3 weeks, depending on the manufacturing effort. Our core competence lies in supplying the customer with exactly what he really needs. Together with our customers, we work out customer-specific, individual solutions and supply corresponding systems from our own production. Csdeilg U Eopfx Aa Ejpw Feel free to contact us by phone to find a suitable solution for your application. Conveyor belt, conveyor belt system, discharge belts, belt conveyor, magnetic separator, overbelt magnetic separator, recycling, wood chips, plastic, metal-free metal detection, neodymium, overbelt magnet, magnetic belt separator