Slitter Rewinder

Fuji Tekko WS266

Condition: excellent (used), Year of construction: 2023, operating hours: 1,851 h, functionality: fully functional, pressing force: 70 t, filling opening width: 1,100 mm, filling opening length: 1,400 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 500 kg, overall weight: 17,000 kg, oil tank capacity: 70 l, Technical data baler: Manufacturer Avermann Maschinenfabrik GmbH & Co. KG, Germany Type AVOS 1410 BS-22/50 Year of construction 2023 Pump operation hours 1,851 hours, as of July 24 Press power main press 70 t (a 70 tonne hydraulic cylinder is installed, special equipment) Specific press force 90,9 N/cm² (a 70 tonne hydraulic cylinder is installed, special equipment) Feed channel 1,400 x 1,000 mm Theoretic cycle time 13 sec Theoretic throughput capacity 266 m³/h Bale size 1,100 x 750 (w x h), the length is variable Drive power 22 kW Connected load 65 kW Tying system 4-fold, vertical, fully automatic Throughput capacity at a bulk weight of 30 kg/cbm approx. 5,5 t/h bulk weight of 50 kg/cbm approx. 7,5 t/h bulk weight of 100 kg/cbm approx. 9,7 t/h Bale weight with a bale length of approx. 1.2 m up to 500 kg, depends on material SPS controller Siemens S7-1500 Tedpou Thbxofx Af Tsf Operating panel Schneider Harmony Baler dimensions built up 8,610 x 2,400 x 3,835 mm (l x w x h) Transport weight baler approx. 17 t Special equipment: Wear-resistant floor made of HARDOX steel Larger main hydraulic cylinder with 70 tonnes of pressing force Special press ram for pressing loose bulk materials with small grain sizes OptiCut XS system for lower cutting forces and higher throughput rates Special pressing piston for pressing "difficult" materials Technical data for the conveyor belt: Manufacturer Avermann Maschinenfabrik GmbH & Co. KG, Deutschland Type KGF GB 1500 Year of construction 2023 Drive power 4.0 kW Belt speed approx. 0.3 m/second Length feeding conveyor 2,679 mm Length elevating conveyor 6,866 mm Length goose neck 1,272 mm Grade 35° Effecting width 1,400 mm Side wall height 800 mm Carrier height 50 mm Carrier distance 750 mm Belt quality EP 400/3, 3:1 (DIN quality N) Overall height 4,515 mm Overall transport dimensions11,148 x 2,502 mm (l x w) Technical data on the non-contact personal protection system: Manufacturer BOREMA Umwelttechnik AG, Switzerland Type APSS iBOR 22 Year of construction 2023 Condition of the press system: The entire system is in very good condition due to the short operating time of only 1,851 pump hours and the processing of only paper, cardboard and film. Scope of delivery: Avermann baler, type AVOS 1410 BS-22/50, incl. wire drawing stations and bale chute Avermann conveyor belt, type KGF GB 1500 BOREMA personal protection system, type APSS iBOR 22 Comments: The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Year of construction: 1974, condition: refurbished (used), functionality: fully functional, machine/vehicle number: 1293, CNC Radial Forging Machine GFM mod. SX-16 Manufacture: GFM (Austria) YOM: 1974 / 2022 Model: SXL-16 Machine number: 1293 PLC: Siemens S7 - Technology V4.2 with CNC Bosch Rexroth XM Numbers of Hammers: 4 Forging force: 800 Ton (200 t per Hammer) Strokes per minute: 580 Hammer length: 320 mm Maximum hammer setting scope - calculated by diameter: 100 mm Maximum diameter of forging regarding: - structural steel: circular cross section – Ø 160 mm square cross section – 130 mm - high alloy steel: circular cross section – Ø 120 mm square cross section – 100 mm Extreme quadrangle: 12 x 120 mm Maximum length of forging: 6000 mm Min and Max diameter of mounting in manipulator: 30 - 160 mm Feed of manipulator A: 6800 mm Feed of manipulator B: 7200 mm Passage through manipulator: Ø 130 mm Manipulators speed in fast move: 400 mm/s Feed speed of manipulators (stepless adjustment): 10 ÷ 115 mm/s Cooling water pressure: 3 ÷ 5 bar Temperature of inlet water: max. 30˚C Cooling water consumption: 34m3/h Pipe diameter for cooling water: 2” Compressed air pressure: min. 5 bar Pipe diameter for compressed air: Ø20 mm Consumption of compressed air: 1,5 Nm3/h Tsdsq U Sa Sepfx Af Tjf Power supply (nominal power): 350 kW Motor voltage: 500 V Control voltage 220 V Power of main engine: 200 kW Power of pump motors: 185 kW Power of manipulators motors: 2 x 22 kW Dimensions of the machine Axis height of forging above the hall level: 750 mm Maximum height of machine above the hall level: 2.050 mm Maximum length of machine on the hall level: 33.740 mm Foundation length: 34.200 mm Maximum width of machine on hall level without loading equipment: 4350mm Foundation width: 15.600mm Machine net weight: 124.490 kg

Condition: good (used), Year of construction: 1998, SANJO P 270 - 6C Age: 1998 Web-width: 270mm 6-color Flexo 1 x Varnish Unit Unwind Rewind One of the printing units, is for back side printing, and is very rare to find for this machine Lot of printing cylinders, aniloxes are coming with the machine DELAM RELAM TENSION CONTROL Todpfegvg A Isx Af Tjf

Condition: new, Year of construction: 2025, Device description The splitter has an overload valve that drains oil to the tank and an efficient, failure-free gear pump. The tree lifting system makes it easier to place heavy materials directly under the splitting wedge 5-pin power connection The wedge set at an angle makes it easier for the wedge to sink into the material. FAILURE-FREE HYDRAULIC PUMP 24l! Technical parameters Pressure force 22 TON Minimum wood diameter 80 mm Maximum wood diameter 700 mm Tsdswnxcmjpfx Af Tjf Minimum wood length 350 mm Maximum wood length 1100 mm Splitting speed (continuously adjustable) 10.5 cm/s Return speed 7.5 cm/s Wedge stroke length 948 mm Total engine power (S1;S6) S1:5.1 kW S6: 6.6 kW Voltage 400 V Hydraulic tank capacity 24 l Hydraulic system pressure 27.7 Mpa Dimensions 1050 x 1550 x 2500 mm Weight approx. 320 kg

Condition: excellent (used), Year of construction: 2006, functionality: fully functional, Automatic Sheet Feeder A-20 (A-3): Mabeg Suction Head, Double Sheet Control Laminating Unit EK 104 (A-EK-3): Waterbased & Thermal Automatic Sheet Seperator TM-104 (TM-3) Tsdpjrp D I Ijfx Af Tjf Seperating Unit: Quadruple Round Knife, Perforating Device Powder Spray Removal Device Automatic Stacker S-3 Max. Sheet Size X : 1040 mm Max. Sheet Size Y : 1140 mm Min. Sheet Size X : 210 mm Min. Sheet Size Y : 210 mm Production Capacity Max : 50 m/min

Condition: ready for operation (used), Model: HSM V-Press 1160 Plus Baler Pressing force (kN): 532 Output (bales/h): 1–2 Max. bale size (mm): 1200x1100x1000–1200 Dimensions (L x W x H) (mm): 1780x1150x2985 Power (kW): 7.5 Year 2007–2008 price €5,500 Tedpfx Asra Nyuof Tsf year 2009–2010 price €5,800 year 2011–2013 price €6,300 We also offer HSM V-Press 1160 Max balers, year 2014–2015 Weight (kg): 2,300 ALSO AVAILABLE: 2017–2018 models – €7,500

Year of construction: 2015, condition: ready for operation (used), This is an inclined wire paper machine for the production of filter nonwovens, filter paper, insulation paper, membrane carriers, cardboard, tablecloths and more, speed: 5-120m/min, flow rate: 2500-20,000l/min, the manufacturers are various companies from Canada, Ukraine and Europe, some modifications have been made to the system such as a new shredder, larger vacuum pump, vibrating screen for water treatment, second headbox, new distributor and more, an inspection is possible. Tsdpfeqzyaxex Af Tof

Condition: excellent (used), Year of construction: 2008, Hello, Machine in very good condition. Tsdpjn Nykwefx Af Tof TM-SERVICE is a company specializing in the service and sale of poultry machinery. We install equipment anywhere, ensuring that the machines we sell are thoroughly inspected and ready for efficient operation.

Condition: excellent (used), Year of construction: 2020, functionality: fully functional, number of ink cartridges: 5, total width: 1,600 mm, year of last overhaul: 2024, input voltage: 220 V, working width: 1,600 mm, product width (max.): 1,600 mm, roll diameter: 1,600 mm, roll width: 1,600 mm, tank capacity: 3 l, HP Latex Printer 375 - 3 liter ink cartridges Only 4500 sqm Last complete service, including change of print heads - July 2024 Average maximum width - 1,63 cm; Tjdsmcw Tlopfx Af Tof Soft RIP Caldera (without PC). Stand, media feed roller, media take-up roller and tension adjustment kit; High precision for material movement; Registration - automatic control of the fit on the sheet, including front/side; Maximum resolution 1200 X 1200 dpi; Automatic double-sided banner printing; 6 print heads - 2 for cyan and black, 2 for magenta and yellow, 1 for light cyan and light magenta and 1 for latex optimizer; Defective nozzle detection and replacement system. Banding elimination solution; Latex-based ink. Barrels of 3 liters; Resistance to scratching; Built-in spectrophotometer for ICC profiling and automatic calibration; Optimized solution for banding removal; Complete drying right inside the printer so that the product is delivered dry and ready for lamination or packaging; Low warm-up time 90 seconds; Automatic feed adjustment; Ink collector for printing on porous textiles. EXW - old price 9900 euro - new price 7900 euro without VAT

Year of construction: 2008, operating hours: 40,000 h, condition: good (used), machine/vehicle number: HBC 140 2x75kW 2008 (00191), Sold by Bollegraaf Recycling Solutions, the original manufacturer of this Bollegraaf baler and conveyor: Bollegraaf HBC140s Baler (2x75kW). Baler: Weight: 47.100 kg Construction year: 2008 Hardox bottom floor plate only Variable channel pressure control Plastic valve Hydraulic pump driven by frequency inverter Anti-rat cabling Oil in-depth filtration Modem Hours 40.000 This baler can also be sold fully refurbished according to the 'Bollegraaf OEM Certified Refurbishment standards'. This includes 2 year guarrantee. Contact us for more information or a quotation. General principles of refurbishment Cleaning & disassembly Before the actual refurbishment takes place the baler is completely cleaned and disassembled in our refurbishment workshop. Tolerances After the disassembly the tolerances of all steel components are measured and re-welded where necessary, this at least applies to the following components; • Ram, • Frame, • Channel, • Pre-press-flap After disassembly and inspection the ram is welded-up again and fitted with new ram wheels. The protective grids and the pre-press flap are made dent-free and repaired where necessary. Repainted After measuring the tolerances and any repair- and welding work, all components are being blasted and coated again. Hydraulics: The hydraulic tank is cleaned. The hydraulic lines & hoses are replaced. The hydraulic components are repackaged. The hydraulic oil is replaced. Cabling: All cabling is checked and replaced if necessary. All junction boxes are replaced and placed back in easily accessible positions. Wear parts: All wearing parts are replaced. The pins and shafts of the cylinders and the channel are replaced with new ones. All wearing parts of (both) needle installations and knotters are replaced for new. Cylinders: The cylinders are repackaged and, if necessary, provided with a new chrome layer or a new cylinder rod. MCC Cabinet Tsdskcgf Hspfx Af Tof The switch box is checked and cleaned. If necessary, electronic components are replaced with new ones. The PLC and HMI (human interface) are replaced with the latest Schneider M340 version including the latest software.