Climate test chamber with humidity, 800 liters

Espec PSL-4KPH -70°C bis +150°C

Condition: excellent (used), machine/vehicle number: 040501, Henneken C2 vacuum tumbler in lovely condition. 3,650 litres, front and rear doors. Dimensions 2.55m wide, 2.04m long, 2.28m high. Also available (at extra cost) Henneken tote bin loader to match. Lodpjqwhiiefx Acushp

Condition: new, Year of construction: 2021, Hiwell batter mixer II Hiwell DJJ100-II batter mixer utilizes ingenious mixer to evenly combine water and batter. This stainless steel mixer is applicable for high viscosity batters such as Tempura batter. Advantages 1. Our parry battering machine involves utilization of cutting-edge control system, thus realizing repeatable operation cycles of high-speed mixing, low speed mixing and alarm on application of batter. Therefore, batter is prevented from sedimentation. 2. Mixing tank in this fruit battering equipment is endowed with separation layer, which is aimed to keep batter temperature between 10-20℃ by ice or cold medium. 3. Our batter mixing equipment comes with batter output pump, which offers excellent connectivity to battering equipment to form batter feeder. 4. Thanks to reliable protection system and Siemens electronic components, thisfruit processing equipment is operator and maintenance friendly. Lhjdpfxog Unrpe Acusp 5. The entire batter mixer is manufactured with quality stainless steel to meet HACCP standards. 6. Optional battering dosing device is available for more accurate viscosity control.

Year of construction: 2015, condition: excellent (used), Syspal Tote Bin Lifter / Tipper Tipping height 1400 Fully stainless steel Mobile on lockable castors Electrohydraulic operation Built-in battery power pack Complete with plug in charger Ledeim Ivvepfx Acuehp Charge lasts for 1 week, depending on usage In excellent condition

Year of construction: 2022, operating hours: 10 h, condition: new, Universal testing machine H5TMC mechanical construction: according to DIN EN ISO 7500-1) 2 backlash-free ball screws, drive via AC servo motor, Fmax = 5 kN, stiffness 10 kN/mm 1 working area up to nominal load: working chamber width: 420 mm (optional extensions: +190mm / +330mm / +620mm) max. test stroke without test tools, adapters and KMZ: 1025 mm (optional extensions: +250mm / +500mm) Lhodpfx Acoiq Hw Ueusp Optional: conversion to floor model, required additional assembly: substructure table Travel speeds: Test speed 0.001 - 2000 mm/min at full load Return speed 2000 mm/min Force measurement: Measuring range: in the range 0.4 - 100 % of the nominal load class 1 (optionally class 0.5) (+/- 1 % of the displayed value according to DIN EN ISO 7500-1) Resolution of force measurement: +/-180,000 digits at 20ms integration time The machine is delivered with a factory test certificate. If, at the customer's request, a factory or DKD calibration is to be carried out at the installation site, this expense must be invoiced separately. Crosshead travel measurement: Incremental rectangular input with encoder monitoring, storage of crosshead position. Resolution of the crosshead travel measurement:

Year of construction: 2024, condition: new, machine/vehicle number: H3000-H5000TM, Universal testing machine H3000TM-H5000TM according to DIN EN ISO 7500 The universal testing machine of the H3000TM-H5000TM series is a single-spindle machine, a robust construction made of aluminum and V2a with ball screws, ball bushing guides and toothed belt drive. The bellows cover protects the spindle and guides. The testing machine is microprocessor controlled and has a membrane keypad. The 2-line LCD display shows the force and travel. The testing machine can be used as standalone or with a PC via USB interface. The displacement is measured by means of an encoder 0.01 mm visible resolution on LCD (internal 0.0001mm). The machine is manufactured with a standard load cell: 0.03% linearity and the corresponding calibration. Optionally it is possible to add a second channel for a second load cell or a displacement transducer. The universal testing machine is manufactured with two different travels, 500mm or 1200mm (without load cell and testing tool). Further scope of delivery: One load cell up to nominal load, 220 Volt cable, USB cable, description, CE declaration of conformity. For more information, please refer to the attached description. Load cell 3000N-5000N Measuring range: 5-5000N tension and compression, with nom. 2mV/V output signal, overload protection: +/- 1000%, linearity: +/- 0.05%, hysteresis: +/- 0.03%, repeatability: +/- 0.02%, with, incl. 1.5m connection cable incl. calibration certificate Lhedpfx Aoiq Hxkecuop Long travel extensometer HE 900mm measuring travel, measuring arms motorized, including electronics Accuracy class class 1 from 1mm travel according to DIN EN ISO 9513 Measuring principle optical incremental Measuring path 900 mm , minus measuring length Display error 6 µm or 2 Resolution 1 µm Actuating force 10 cN Standard initial device measuring length (Lo) 10-100 mm, in 5 mm steps Lo adjustment is manual Measuring arm opening and closing is motorized specimen diameter 0-30 mm specimen thickness 0-30 mm sample width 0-100 mm Weight approx. 32kg Scope of delivery strain gauge complete with electronics Cutting edges round: 1 set each carbide / rubber wear parts measuring blades optional rectangular cutting edges ATTENTION: When using optional cutting edges a readjustment of the lo a readjustment of the lo stop is necessary.

Year of construction: 2022, condition: excellent (used), functionality: fully functional, We are selling an Instron tensile and compression testing machine in excellent condition. Instron 34TM-50 benchtop model Config: E1-F1-G1 50KN Year of manufacture: 2022 Weight: 151Kg Load transducer: 50KN 2530-50kN/165541 Load transducer: 5kN 2530-5kN/166885 Last service and calibration August 2024 Next service and calibration August 2026 The 3400 Series universal testing machines cover a test force range from 500 N to 300 kN. Featuring the patent-pending Instron operator protection architecture, the 3400 Series testing machines are easier to use, smarter, and safer than ever before. The testing systems are suitable for performing tensile, compression, bending, peeling, puncture, friction, shear, and numerous other tests and can be used with a wide range of clamping devices and testing fixtures from our extensive accessories catalog. Total height: 1604mm Lhedpfxswz Ikte Acujp Maximum vertical test space (daylight test - from base to bottom of crosshead): 1198mm Test type: Tension, compression, and zero-crossover operation Basic control mode: Displacement control Load capacity - kN (lbf): 50 (11240) Maximum speed - mm/min (in/min): 508 (20) Minimum speed - mm/min (in/min): 0.05 (0.002) Maximum force at maximum speed - kN (lbf): 25 (5620) Maximum speed at maximum force - mm/min (in/min): 254 (10) Return speed - mm/min (in/min): 508 (20) Crosshead speed accuracy: ± 0.2% of the set speed at a steady rate and without Load Travel (Crosshead Position) Display Accuracy: In no-load condition, ±0.02 mm (0.0008 in) or ±0.10% of the displayed reading, whichever is greater. Travel (Crosshead Position) Repeatability - mm (in): ±0.015 (0.0006) Load measurement accuracy: ±0.5% of the reading up to 1/200 of the force transducer's rated force. Strain measurement accuracy: ±0.5% of the displayed reading up to 2% of the full scale value, with an ASTM E83 Class B or ISO 9513 Class 0.5 strain transducer.

Year of construction: 2018, condition: good (used), functionality: fully functional, machine/vehicle number: H3000TM, Universal testing machine H3000TM Made in Germany Crosshead stroke: 520 mm Working area depth: 66 mm Total height: 1010 mm Weight: 45 kg Test speed: 1 to 500 mm / min Return speed: 500 mm / min Travel resolution: 0.01 mm We have a very large selection of clamping fixtures - screw clamping fixtures - wedge clamping fixtures - pneumatic and hydraulic clamping fixtures. Pressure plates-bending fixtures-friction fixtures and much more. Strain gauges-extensometers-long displacement transducers-clamp-on transducers-clamping chambers. Force transducers optionally 50N-100N- 200N- 500N- 1000N- 2000N- or 3000N incl. Hess software Windows 8-9-10 or 11 for universal test sequences, simple tests even without a PC and a 5KN SP 56g screw clamp with pyramid or rubber jaws 30x50 mm Factory calibration certificate with DAkkS calibrated measuring equipment. In tension and compression direction in 10 steps. Lhedpet Rg H Ajfx Acuep The universal testing machine of the H3000TM series is a single-spindle machine, a robust construction made of aluminum and V2a with ball screws, ball bushing guides and toothed belt drive. The bellows cover protects the spindle and guides. The testing machine is microprocessor-controlled and has a membrane keypad. The force and travel are shown on the 2-line LCD display. The testing machine can be used as a standalone unit or with a PC via a USB interface. The displacement is measured using an encoder with 0.01 mm visible resolution on the LCD (internal 0.0001mm). The machine is manufactured with a standard load cell: 0.03% linearity and the corresponding calibration. Optionally it is possible to add a second channel for a second load cell or a displacement transducer. The universal testing machine is manufactured with two different travel ranges, 500 mm or 1200 mm (with load cell without test tool). Additional scope of delivery: A load cell of your choice 50N-100N-200N-500N-1000N-2000N or 3000N, certificate 220 volt cable, USB cable, description, CE declaration of conformity. Load cell 3000N Measuring range:1-3000N tension and compression, with nom. 2mV/V Output signal, overload protection: +/- 100%, linearity: +/- 0.05%, hysteresis: +/- 0.03%, reproducibility: +/- 0.02%, with, incl. 1.5m connection cable incl. calibration certificate

Condition: excellent (used), Year of construction: 2024, operating hours: 5,000 h, functionality: fully functional, machine/vehicle number: 2MAM022829, cooling capacity: 1,000 kW (1,359.62 HP), Cooling Capacity: 959 kW Type of Input Current: 3 Phase / 50 Hz / 400 V Type of Cooling: Air-cooled Overall Weight: 7,973 kg (Operating) / 7,597 kg (Rigging) Ambient Temperature (max.): 35°C Ambient Temperature (min.): 12.8°C (based on part load performance) Compressor Type: Screw, semi-hermetic, VSD controlled Total Power Consumption: 309.9 kW Noise Level: 74 dB(A) 10 m Refrigerant Type: R134a, total charge: 242 kg Water Flow Rate: 146.7 m³/h (40.76 L/s) Pressure Drop (Evaporator): 52.2 – 64.1 kPa Lhsdpfoimz Uaox Acusp COP (Full Load): 3.09 IPLV (Part Load): 5.12 Number of Fans: 14 units (7+7), with low sound kit Nameplate Available: Year of Manufacture: 2018

Condition: used, Vacuum tumbler Manufacturer: Henneken Model: B3 Volume: 1200 liters Electric power: 2.8kW Ljdpfxeui Rgkj Acuehp Dimensions: 1130x2225x1675mm

Condition: good (used), White Type: SC/KWT 450 Salt spray chamber Technical data: Test chamber capacity 450 liters Max. load 100 kg Brine storage tank 180 liters Lodeudvg Rspfx Acuehp External dimensions: Height 920 mm Width 1930 mm Depth 800 mm Test compartment dimensions: Height 740 mm Width 850 mm Depth 570 mm Areas of application: Corrosion tests: Salt spray test: room temp. up to + 50°C Condensation water test: Room temp. up to + 45°C Humidifier +75°C Temperature constancy The temperature deviation over time is ± K. Voltage: 1/N/PE AC 230V ±10% 50Hz Rated power 2.0 kW Rated current 8.5 A Combination: Salt spray test SS: DIN 50021 Condensation water test KFW: DIN 50017 Normal climate (ventilation): DIN 50014 Weight: 180 kg Condition: second-hand / used Scope of delivery: (see picture) (We reserve the right to make changes and errors in the technical data and specifications) We will be happy to answer any further questions you may have on the phone.