Shaft Alignment Machine

Cimat RT 505 CMT-300H2W

Condition: new, functionality: fully functional, Year of construction: 2026, roller (bottom) diameter: 310 mm, roller (top) diameter: 320 mm, roller diameter: 310 mm, roller length: 1,550 mm, working width: 1,500 mm, sheet thickness steel (max.): 38 mm, overall weight: 12,500 kg, total length: 4,500 mm, total width: 2,300 mm, total height: 1,740 mm, power: 18.39 kW (25.00 HP), working length: 1,500 mm, Equipment: documentation/manual, emergency stop, FACCIN HAV 15342 variable three-roll bending machine Electronically controlled, hydraulic three-roll bending machine Technical data: Number of rollers: Three Geometry of the side rollers: variable Working width: 1550 mm Top roller diameter: 320 mm Side roller diameter: 310 mm Pressure force against the top roller: 160 tons Working pressure at nominal force: 250 bar Guaranteed installed power: 18 kW (25 hp) Guaranteed maximum rotation speed: 3.5-7 m/min Guaranteed machine weight: 12,500 kg Length: 4,500 mm Width: 2,300 mm Height: 1,700 mm Guaranteed performance: for material with yield strength 260 N/mm² Rolling capacity (full working width) 38 mm Bending capacity (full working width) 20 mm from pipe diameter 1,600 mm Rolling capacity (full working width) 30 mm Bending capacity (full working width) 17 mm from pipe diameter 415 mm Standard equipment: Variable geometry with linear guides for roller movement Extra long folding bearing for increased frame stability Electronic parallelism system EPS Hardened rollers for high wear protection All rollers ground after heat treatment Siemens S7-HMI PLC control system PGS-CLASSIC control system with Siemens touch panel Hitech hydraulic and electrical package Simultaneous rotation and roller movement Safety ripcord with emergency stop and CE certification Central lubrication Todpfx Amet Akt Roysa Water cooling for the hydraulics Cone bending device Prepared for retrofitting of supports and roller conveyors FACCIN Advantage Package AP

Condition: new, cutting diameter 355 mm dimensions of saw-band 3770 x 34 x 1,1 mm cutting speed 20 - 80 m/min cutting width 490 x 280 mm 290 mm Impact energy 250 mm Tjdpemhm Aqsfx Amyoa 230 mm 180 mm connected load frequency 400 Volt total power requirement 2,2 kW weight of the machine ca. 0,7 t dimensions 1,43 x 0,72 x 1,7 m Semi-automatic miter band saw - Miter cuts up to 45° left + right - Miter cuts up to 60° right - Vice with quick release device - Tape tension control via manometer - Electr. automatic cooling

Condition: good (used), functionality: fully functional, Year of construction: 2005, machine/vehicle number: MC0 35100, control type: CNC control, degree of automation: semi-automatic, actuation type: hydraulic, roller diameter: 1,000 mm, sheet thickness (max.): 130 mm, sheet thickness steel (max.): 130 mm, total length: 3,500 mm, power: 240 kW (326.31 HP), Technical details Max. bending width: 3,500 mm Max. sheet thickness: 200 mm Total power requirement: 160 kW Tedpfx Ajyn Agbsmyoa Smallest roll-in diameter: 770 mm Maximum cylinder pressure: 2 x 2 t Top roll Ø1000 mm Bottom rolls Ø900 mm

Condition: used, FARINA hydraulic press brake, 5000 x 100 tons, throat depth 400. Dimensions: 555 x 220 x 290 (H), weight 15,100 kg (151 quintals). Tjdpfx Asfrllqjmyja

Condition: used, plate width 2500 mm plate depth 5100 mm plate height 400 mm weight ca. 9 t Tjdpfx Amjhpva Doyoa required space 2,5 x 5,1 x 0,40 m

Condition: ready for operation (used), Year of construction: 2001, functionality: fully functional, machine/vehicle number: 11311, workpiece weight (max.): 30 kg, type of input current: three-phase, input current: 12 A, input frequency: 50 Hz, input voltage: 400 V, rotor diameter: 1,000 mm, Balancing Machine, vertical shaft. Measurement in two planes. Maximum rotor weight: 30 kg (tooling included). Automatic Indexing (rotor will, after measurement be positioned with correction location at the front). Rotor speed can be set for each programmable standard workpiece type. Some tooling is included. Todox H Aa Tepfx Amyea Machine is available because fans are no longer built by the customer.

Condition: used, Year of construction: 1995, documentation vorhanden Todsyhrcropfx Amyja dimensions of the machine ca. 4,10 × 1,20 × 1,40 m

Year of construction: 1980, condition: used, The Sledum RG-270 is a high-precision, industrial-grade crankshaft grinding machine developed for the precision grinding of crankshafts in internal combustion engines and the journal surfaces of similar rotating components. The machine is built on a massive cast-iron machine bed, offering high stability and vibration damping. The design enables uniform, high-precision machining of large crankshafts. Key Technical Features: Distance between centers: 2000 mm Maximum swing radius: 270–275 mm Machinable parts: crankshafts, shafts, eccentric rotating components Grinding spindle with high-rigidity bearings Fine-feed cross and longitudinal slide system Machine bed with precision guide rails Adjustable steady rest system for stable support of long workpieces High-power grinding motor for continuous industrial operation Manually controlled feed and positioning system Stable, vibration-damped industrial machine frame Coolant system with preparation/conditioning unit Heavy-duty industrial construction, designed for long service life Accessories and Equipment: Complete headstock and tailstock (counter-spindle) system Tjdpfx Aozbiblemysa Grinding spindle unit with grinding wheel mount Adjustable steady rests for long shafts Workpiece clamping system Precision alignment and centering components Grinding wheel mounting flanges Workpiece rotation mechanism Manually controlled operator panel Complete slide system with fine feed Coolant connection points Machine body and industrial machine bed Adjustable workpiece support units

Condition: used, Year of construction: 1961, workpiece weight 300 kg workpiece length 1200 mm diameter 1300 mm The tech. Data are manufacturer or operator information and therefore non- binding. We reserve the right to prior sale; Our terms and conditions of sale apply exclusively. About us More than 400 of our own machines in stock Over 15,000 m² of storage space, 70 t crane capacity Tjdpfx Amjy Swhvjyja More than 10,000 items and accessories for your workshop If you are interested in selling machines, production lines, or your business, please contact us. You can find further offers on our website. Tours are possible by appointment. We look forward to your visit. Your Markus Hirsch Team

Condition: good (used), Year of construction: 2008, sheet thickness (max.): 13 mm, cutting length (max.): 4,160 mm, DENER Hydraulic Shear 4100x13mm DMMH.4113 Brand: Dener Model: DMMH NC 4113 Year: 2008 Todpewi Snxsfx Amyea Standard Control: Dener HT 071 Cutting Length: 4,160 mm Maximum Cutting Thickness: 13 mm Cutting Inclination: 2º Number of Hold-Downs: 19 Motor Power: 30 kW Cuts/min.: 8 Manual Lubricator *Shear under inspection. Blades have been removed for grinding. Hold-downs have been removed for replacing seals and gaskets. Delivered fully inspected and with a 6-month warranty.