Baler

BOA 2040

Condition: excellent (used), Year of construction: 2023, operating hours: 1,851 h, functionality: fully functional, pressing force: 70 t, filling opening width: 1,100 mm, filling opening length: 1,400 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 500 kg, overall weight: 17,000 kg, oil tank capacity: 70 l, Technical data baler: Manufacturer Avermann Maschinenfabrik GmbH & Co. KG, Germany Type AVOS 1410 BS-22/50 Year of construction 2023 Pump operation hours 1,851 hours, as of July 24 Press power main press 70 t (a 70 tonne hydraulic cylinder is installed, special equipment) Specific press force 90,9 N/cm² (a 70 tonne hydraulic cylinder is installed, special equipment) Feed channel 1,400 x 1,000 mm Theoretic cycle time 13 sec Theoretic throughput capacity 266 m³/h Bale size 1,100 x 750 (w x h), the length is variable Drive power 22 kW Connected load 65 kW Tying system 4-fold, vertical, fully automatic Throughput capacity at a bulk weight of 30 kg/cbm approx. 5,5 t/h bulk weight of 50 kg/cbm approx. 7,5 t/h bulk weight of 100 kg/cbm approx. 9,7 t/h Bale weight with a bale length of approx. 1.2 m up to 500 kg, depends on material SPS controller Siemens S7-1500 Operating panel Schneider Harmony Baler dimensions built up 8,610 x 2,400 x 3,835 mm (l x w x h) Transport weight baler approx. 17 t Special equipment: Wear-resistant floor made of HARDOX steel Larger main hydraulic cylinder with 70 tonnes of pressing force Special press ram for pressing loose bulk materials with small grain sizes OptiCut XS system for lower cutting forces and higher throughput rates Special pressing piston for pressing "difficult" materials Technical data for the conveyor belt: Manufacturer Avermann Maschinenfabrik GmbH & Co. KG, Deutschland Type KGF GB 1500 Year of construction 2023 Drive power 4.0 kW Belt speed approx. 0.3 m/second Length feeding conveyor 2,679 mm Length elevating conveyor 6,866 mm Length goose neck 1,272 mm Grade 35° Effecting width 1,400 mm Side wall height 800 mm Carrier height 50 mm Carrier distance 750 mm Belt quality EP 400/3, 3:1 (DIN quality N) Overall height 4,515 mm Overall transport dimensions11,148 x 2,502 mm (l x w) Technical data on the non-contact personal protection system: Manufacturer BOREMA Umwelttechnik AG, Switzerland Type APSS iBOR 22 Tsdpeu Thbxofx Af Tef Year of construction 2023 Condition of the press system: The entire system is in very good condition due to the short operating time of only 1,851 pump hours and the processing of only paper, cardboard and film. Scope of delivery: Avermann baler, type AVOS 1410 BS-22/50, incl. wire drawing stations and bale chute Avermann conveyor belt, type KGF GB 1500 BOREMA personal protection system, type APSS iBOR 22 Comments: The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Year of construction: 2008, operating hours: 40,000 h, condition: good (used), machine/vehicle number: HBC 140 2x75kW 2008 (00191), Sold by Bollegraaf Recycling Solutions, the original manufacturer of this Bollegraaf baler and conveyor: Bollegraaf HBC140s Baler (2x75kW). Baler: Weight: 47.100 kg Construction year: 2008 Hardox bottom floor plate only Variable channel pressure control Plastic valve Hydraulic pump driven by frequency inverter Anti-rat cabling Oil in-depth filtration Modem Hours 40.000 This baler can also be sold fully refurbished according to the 'Bollegraaf OEM Certified Refurbishment standards'. This includes 2 year guarrantee. Contact us for more information or a quotation. General principles of refurbishment Cleaning & disassembly Before the actual refurbishment takes place the baler is completely cleaned and disassembled in our refurbishment workshop. Tolerances After the disassembly the tolerances of all steel components are measured and re-welded where necessary, this at least applies to the following components; • Ram, • Frame, • Channel, • Pre-press-flap After disassembly and inspection the ram is welded-up again and fitted with new ram wheels. The protective grids and the pre-press flap are made dent-free and repaired where necessary. Repainted After measuring the tolerances and any repair- and welding work, all components are being blasted and coated again. Hydraulics: The hydraulic tank is cleaned. The hydraulic lines & hoses are replaced. The hydraulic components are repackaged. The hydraulic oil is replaced. Cabling: All cabling is checked and replaced if necessary. All junction boxes are replaced and placed back in easily accessible positions. Wear parts: Tsdokcgf Hopfx Af Tef All wearing parts are replaced. The pins and shafts of the cylinders and the channel are replaced with new ones. All wearing parts of (both) needle installations and knotters are replaced for new. Cylinders: The cylinders are repackaged and, if necessary, provided with a new chrome layer or a new cylinder rod. MCC Cabinet The switch box is checked and cleaned. If necessary, electronic components are replaced with new ones. The PLC and HMI (human interface) are replaced with the latest Schneider M340 version including the latest software.

Condition: ready for operation (used), total height: 3,020 mm, total length: 3,300 mm, total width: 5,100 mm, throat depth: 1,060 mm, zware dubbelkoloms lintzaag voor het zagen van hooggelegeerde staalsoorten automatische invoer van het werkstuk met automatische herpositionering CNC-gestuurde variabele snelheid voor invoer en zagen spaantransportband Tedpfov Sfp Ajx Af Tsf uitgerust met volledig gemotoriseerde Weisshaupt-rollenbanen: - 10,3 meter invoerrollenbaan (buiten) met 2 hydraulische klemmen voor de contouren van het werkstuk - 9 meter invoerrollenbaan (binnen) met 2 hydraulische klemmen voor de uitlijnen van het werkstuk - Maximale werkstukbreedte: 900 mm - elke rol is gemotoriseerd - de capaciteit van één rollenbaan is 4 ton - 4 meter uitvoerrollenbaan: één rollenbaan is uitgerust met een weegschaal om het werkstuk na het snijden te wegen (Sartorius-systeem) Max height of workpiece: 860 mm Sawspeed: 16 > 80 m/min Length of band saw: 10260 x 80 x 1,60 mm Power needed: 32 kW (100 amp) Weight: 9 ton (only machine)

Condition: excellent (used), Year of construction: 2018, functionality: fully functional, paper width (max.): 330 mm, paper height (max.): 487 mm, number of feeding trays: 3, Equipment: auto duplex, brochure finisher, Konica Minolta Bizhub Pro C2060l sheet-fed digital color printing machine with Fs-612 brochure finisher Maximum media size is 330x487mm, in banner mode up to 1200mm length. In very good condition Tsdpev Sq Sijfx Af Tof

Condition: used, !! Short delivery time, we will be happy to advise you!! A simple flow-wrapping machine that is suitable for packaging various products. Tjdpfx Aou T N Umef Tof Used.

Condition: reconditioned (used), Year of construction: 2020, operating hours: 3,300 h, functionality: fully functional, overall weight: 28,000 kg, total width: 2,500 mm, VZ 850 DK, Volvo Penta TAD16 L 770 HP, 3,300 operating hours - Conveyor belt as new, rollers replaced - Fine shredding shafts 12-9 as new - Counter-blade as new - Two hoppers - Long discharge conveyor - Magnetic belt Tjdpfx Afjw S Iiie Tof - Track undercarriage guard - Cleanfix reversible fan

Condition: reconditioned (used), Year of construction: 2005, operating hours: 30,408 h, functionality: fully functional, pressing force: 50 t, filling opening width: 1,100 mm, filling opening length: 1,250 mm, bale width: 1,100 mm, bale height: 720 mm, bale weight: 550 kg, overall weight: 16,000 kg, oil tank capacity: 600 l, year of last overhaul: 2024, Technical data baler: Manufacturer Presona AB Type LP 50 EH1 Year of construction 2005 Operating hours 30,408 hours, as of April Number of pressed bales 198,059 as of April Pressing force main press 50 tonnes Specific pressing force 63 N/cm² Theoretical throughput capacity 530 m³/hour Throughput capacity under operating conditions 260 m³/hour Dimensions of feed chute 1,250 x 1,100 mm Bale chamber volume 2.2 m³ Bale dimensions 1,100 x 720 mm, variable length Drive power 22 kW Tying 5-fold vertical, fully automatic Throughput rates with a bulk density of 30 kg/cbm 6 up to 7 tonnes/hour Bulk weight of 50 kg/cbm 7 up to 9 tonnes/hour Bulk weight of 100 kg/cbm 11 up to 14 tonnes/hour Bale density (paper/newspapers) 400 to 550 kg/m³ Hydraulic oil tank capacity 600 litres PLC control Telemecanique TSX Micro Schneider Magelis control panel Effective transport dimensions excl. baler 8,125 x 2,300 x 3,000 mm (L x W x H) Transport weight press approx. 16 tonnes Condition of the baler: The machine was partial overhauled in our workshop and general maintenance work was carried out. After completion of the overhaul work, the press was tested during operation and is available for sale at short notice. The following overhaul work was carried out: General work: Machine cleaned, derusted, primed, partially painted Wire entry marks in the press channel feed-throughs welded shut and smoothed Hydraulic unit: Hydraulic oil tank emptied, tank cleaned, new oil filled Oil filter and air filter replaced Leaky oil sight glass on hydraulic oil tank replaced All hydraulic hoses replaced Electrics: English language installed in the programme menu Two key switches in the control panel replaced Control cabinet replaced Signal lamp on the control cabinet replaced Flaps end switch replaced Electrical system of the turbulator replaced, connected and tested Press ram: All four rollers removed from the press ram and replaced Main hydraulic cylinder dismantled, disassembled and partially overhauled, cylinder tube honed, complete seal set replaced, leak test performed All plastic wear pads on the press ram replaced Pre-press: Todpfx Aju Thhrjf Tjf Both bearings on the pre-press shaft replaced. Both hydraulic cylinders dismantled, disassembled and partially overhauled, both cylinder tubes honed, complete seal sets replaced, leak test performed. Scraper flap on the pre-press replaced. Binding system: Two complete needles with wire deflection rollers replaced Needles adjusted and set All wire deflection rollers in the needle heads replaced Drill fingers replaced Two drill shafts replaced All 8 wear plates on the Drillomat, under the drill fingers, replaced Scope of delivery: Only the baler will be sold. The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: excellent (used), grinding length: 3,500 mm, center width: 5,000 mm, Cylindrical Grinding Machine Tjdpfx Afswb Dq No Tjf Manufactured by Joh. Schehr, Meuselwitz Type SAXW 1000 Weight 33 tons Center distance 5000 mm Grinding length 3.5 meters Concave and convex grinding direction Total length 9.6 meters Width 3 meters Height 2.4 meters 380 volts The machine can be inspected under power at the supplier's factory.

Condition: excellent (used), Year of construction: 2005, functionality: fully functional, Year of production: 2005 Manufacturer: GUK-Falzmaschinen Griesser & Kunzmann GmbH & Co. KG Machine availability – on request; Machine in use; possibility to carry out work tests during inspections; Good technical condition; Folding machine manufactured by the renowned German company GUK equipped with a high pile feeder (sheet picking with a suction roller from above) FL2-50, 2 folding pockets aggregates, pocket with maximum working widths of 50 cm and mobile chute delivery. Folding machine GUK model FA 50/6-6 FL2-50 – infeed width 500 mm (6+6 folding pockets). Maximum input format: 500 x 850 mm Minimum input format: 105 x 145 mm Minimum folding length: 45 mm Feed rate of sheets from feeder: 40 - 180 m/min Maximum performance: 27.000/from sheet A4 Tedpforx S Iwox Af Tsf Power supply: 400 V/50 Hz Machine equipment: High pile feeder FL2-50; Batch counter. Multifunction counter programming the operation of the machine. Ability to fold sheets in groups (lots) of the given number in each lot, with stepless adjustment of the spacing between parties. I. folding unit FA 50/6, 6 folding pockets; Sound reduction hood, top. II. folding unit FA 50/6, 6 folding pockets Sound reduction hood, top. Mobile chute delivery S 520. To be added after I or II folding station.

Condition: used, Year of construction: 2009, operating hours: 20,536 h, pressing force: 80 t, filling opening width: 1,100 mm, filling opening length: 1,400 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 600 kg, empty load weight: 16,000 kg, Technical data baler: Manufacturer Avermann Maschinenfabrik GmbH & Co. KG, Germany Type AVOS 1410-45/80 Year of construction 2009 Operation hours 20,536 hours, as of September 2024 Press power main press 80kN Specific press force 103,9 N/cm² Feed channel 1,400 x 1,000 mm Theoretic cycle time 12 sec Theoretic throughput capacity 300 m³/h Bale size 1,100 x 750 (w x h), the length is variable Drive power 45 kW Connected load 75 kW Tying system 4-fold, vertical, fully automatic Throughput capacity at a bulk weight of 30 kg/cbm approx. 6,0 t/h bulk weight of 50 kg/cbm approx. 10,5 t/h bulk weight of 100 kg/cbm approx. 17,5 t/h Bale weight with a bale length of approx. 1.2 m up to 600 kg, depends on material SPS controller Siemens S7-300 Tedpfx Afeu Thypo Tjf Operating panel pulsotronic Baler dimensions built up 8,610 x 2,400 x 3,835 mm (l x w x h) Transport weight baler approx. 16 t Special equipment: Wear-resistant floor made of HARDOX steel Special press ram for pressing ‘difficult’ materials and loose bulk materials with small grain sizes Control cabinet air conditioning Machine foot elevation 200 mm Remark: The machine is currently in our workshop undergoing partial refurbishment. We expect the refurbishment work on the machine to be completed by the end of October, after which the machine will be tested and released for sale.