Format saw

ALTENDORF ALTENDORF F45

Condition: ready for operation (used), Technical characteristics 3200 mm carriage with double rollers Maximum blade diameter: 350 mm 45° hydraulic blade tilt Digital display of dimensions on console Iaodpeucip Nofx Ah Nsl Overhead control panel Automatic movement of the rip fence to the required dimension Crosscut fence Double stop Motorised rip fence, length 1300 mm Fine adjustment of rip fence Main blade motor: 5.5 kW DUPLEX mitre fence, scale-adjustable with extended fence rail Power and Motors Voltage: 380 V Pluging: Three-phased Power: 7,5 Kw Overall dimensions

Condition: used, heavy-duty surface planer SCM F 520 planing width 520 mm table length 2,960 mm hydraulic height adjustment of infeed table via foot pedal, with micrometer display for chip removal 4-knife safety cutterblock sharp and hollow joint adjustment Iaodpjxzdgujfx Ah Nsl main motor 4 kW electric motor brake CE version Machine is FULLY FUNCTIONAL and in GOOD CONDITION from vocational school available from stock in Lieboch

Condition: new, capacity 90 degrees: round 350 mm capacity 90 degrees: square 330 mm 450x320 saw band length 4250x34x1,1 mm band speed 40 + 80 m/min table height 845 mm saw band width 34 mm total power requirement 2,2 kW weight of the machine ca. 0,985 t dimensions of the machine ca. 1,4 x 2,0 x 2,2 m Double miter band saw, hydraulic semi-automatic, DGS 350/450 HA-I · miter left + right 60° without machine conversion · 34 mm saw blade width · Large material support turntable, ball bearings · To position the saw blade guides using a very wide linear guide · Strong, robust transmission · Large chipboards · Infeed and outfeed roller Removable chip tray (disinfection) · Free-standing control panel, safe and ergonomic · Storage space for tapes, consumables · Cutting pressure regulator Feed regulator · Fully hydraulic vise Preload super fast (front loading) · Material height sensor (automatic cut start detection) Semi-automatic function: Iodpfjfgyicsx Ah Nsal 1. Clamp material 2. Saw starts 3. Rapid lowering to the start of the material or the same for series cutting cut 4. Saw band off 5. Raise the frame to just above the material 6. Open the vise Optimum, material-independent cutting result through fine adjustment of the saw frame by means of: *Pressure Control Valve (Cutting Pressure Force) *Feed Control Valve (Speed) *Switch with pictogram, easy and clear to use

Condition: new, capacity 90 degrees: round 305 mm capacity 90 degrees: square 260 mm 350 x 200 saw band length 3375 x 27 x 0,9 mm band speed 37 + 74 m/min table height 940 mm total power requirement 1,5/1,8 kW weight of the machine ca. 0,61 t Iaodpfxsfd Abaj Ah Nel dimensions of the machine ca. 1,5 x 1,75 x 1,9 m Double miter metal band saw with AutoCut function - Miter cuts up to 60° left and 45° right - Ball bearing turntable - Vice can be moved sideways - Massive, large material support - Automatic cooling Figure is semi-automatic.

Condition: ready for operation (used), functionality: fully functional, mileage: 80,000 km, power: 103 kW (140.04 HP), fuel type: diesel, Year of construction: 2023, Equipment: ABS, airbag, electronic stability program (ESP), sliding door, More than 20 vans with same or similar configuration is available. Cars are located in the Baltics and can be visited/inspected via prior appointment. MINIMUM ORDER QUANTITY IS 3 UNITS! PRICE PER UNIT! Price does not include any taxes or delivery fees. Machines are in good condition and have full maintenance history! The milage may vary depending on the vehicle, however is all below 100 000 km. More pictures/videos and additional information including configurations upon request. Iajdpfx Asxgdd Doh Njl Individual and patch sales is both possible!

Condition: good (used), Year of construction: 1991, max. planing width 520 mm max. planing height 200 mm 4 cutterblocks slotted table lips Iajdjiwi Ezjpfx Ah Nol electr. height adjustment with trolley with knife setting gauge

Condition: used, Year of construction: 1990, functionality: fully functional, machine/vehicle number: C4652, grinding length: 5,100 mm, grinding width: 250 mm, overall weight: 9,100 kg, space requirement height: 2,300 mm, space requirement length: 9,000 mm, space requirement width: 4,000 mm, Reform AR 51 Type 7 Ijdpfxjtqtk Aj Ah Noal Surface grinding machine Year of manufacture: 1990 Grinding length: 5100mm Grinding width: 250mm Workpiece height: 220mm Total power requirement: 36kW Used water system Lifting station, magnetic roller, pump

Condition: good (used), Year of construction: 2013, Panel saw Felder K 975 Iajdpfexl Dw Uex Ah Nel Cutting length: 3200 mm Cutting width: 1350 mm Max. cutting height: 130 mm (saw blade diameter: 400 mm) Saw blade and scorer tilting: 0-45° digital Saw blade and scorer height adjustment: digital Manual adjustable rip fence Activation of main saw blade and scorer from control panel and/or machine table Main motor for panel saw: 5.5 kW (7.5 HP) (adjustable 3500/4500/5500 rpm) Scorer motor for panel saw

Year of construction: 2024, condition: new, The obtained juice flows into integrated collection tank under the press. Then the pump transfers the juice from the press to a desired tank for further processing. The pressing process is continuous. Capacity: 3000 kg/h. The most evolutionary feature of our Belt press POWERPRESS line is that belt presses come with integrated pump and juice collection tank. This means you save money and do not need additional juice collection tank and pump which otherwise would use much space and cause additional costs. Iodpfxjq Nl Aqe Ah Neal -The juice yield of apples using our belt press 3000 is ~75 %. -There is a filtration sieve integrated into the juice collection tank. It filtrates the juice providing clearer and purer product. -The belt presses work automatically: when the mash inlet tank is full, all other machines, which come before belt press, turn off automatically. When the juice tank is full, the pump automatically pumps the juice into the tanks. -The belt press 3000 includes a high-pressure washer, which continuously washes the belt of the machine. Our belt washing system is simple, does not contain any engines or reducers, so it prolongs the use time and saves the service costs. -Pneumatic lifting of the security cover of the press ensures easier access when cleaning. -After work, belt press should be manually washed with a water stream. A full washing process takes around 15-20 minutes. Washing is simple and all the parts of the belt press are easily removable without any tools. -Belt tension is adjustable. -Machine is made entirely of stainless steel and has adjustable feet for more convenient use. -Easy to clean with no closed or inaccessible spaces, all parts are easy to assemble.

Condition: good (used), Year of construction: 2007, Technical characteristics : - Max machinable length 3200 mm - Minimum machinable length 200 mm - Maximum width 200 mm - Minimum width 40 mm - Maximum workpiece height 130 mm - Depth with max Ø to tenon 320 mm: 105 mm - Tenoning carriage speed min / max 0/100 m / min - Min / max profiling speed: 3/15 m / min Tenoning: 1- end cut saw 5.5 hp (4 kW) Saw Ø 400 mm 2- tenoning router Counter bearing 50 x 620 mm 15 hp (11.3 kW) Max tool Ø 320 mm Axle stroke 575 mm Automatic splinter guard 3- tenoning router Counter bearing 50 x 620 mm 15 hp (11.3 kW) Max tool Ø 320 mm Axle stroke 575 mm Automatic splinter guard Vertical positioning with continuous axis 4- Digital angular adjustment clamp Profiling: 5-: router to be profiled on the right Shaft 50 x 320 mm Iodpfot R T Hcox Ah Njal 10 hp (7.5 kW) Ø tools 130/240 mm Axle stroke 280 mm Time-delayed anti-shattering intervention during calibration Double direction of rotation Vertical and horizontal positioning with continuous axis 6-: router to be profiled on the right Shaft 50 x 320 mm 10 hp (7.5 kW) Ø tool 130/240 mm Axle stroke 280 mm Vertical and horizontal positioning with continuous axis 7-: router to be profiled on the right Shaft 50 x 320 mm 10 hp (7.5 kW) Ø tool 130/240 mm Vertical and horizontal positioning with continuous axis 8-: close-out recovery group Vertical and horizontal positioning with continuous axis Device for extracting the shutter 9-: lower horizontal shaft for groove Vertical and horizontal positioning with continuous axis 88.5 hp (66.4kW) 10-: digital guide 11-: Return of parts to the operator NO TOOLS AVAILABLE OBTAIN ADDITIONAL PHOTOS NOTE: SUBJECT TO CHANGES IN TECHNICAL DATA