Conveyor belt with cleats

AGRIFON

Condition: reconditioned (used), Year of construction: 2005, operating hours: 30,408 h, functionality: fully functional, pressing force: 50 t, filling opening width: 1,100 mm, filling opening length: 1,250 mm, bale width: 1,100 mm, bale height: 720 mm, bale weight: 550 kg, overall weight: 16,000 kg, oil tank capacity: 600 l, year of last overhaul: 2024, Technical data baler: Manufacturer Presona AB Type LP 50 EH1 Year of construction 2005 Operating hours 30,408 hours, as of April Number of pressed bales 198,059 as of April Pressing force main press 50 tonnes Specific pressing force 63 N/cm² Theoretical throughput capacity 530 m³/hour Throughput capacity under operating conditions 260 m³/hour Dimensions of feed chute 1,250 x 1,100 mm Bale chamber volume 2.2 m³ Bale dimensions 1,100 x 720 mm, variable length Drive power 22 kW Tying 5-fold vertical, fully automatic Throughput rates with a bulk density of 30 kg/cbm 6 up to 7 tonnes/hour Bulk weight of 50 kg/cbm 7 up to 9 tonnes/hour Bulk weight of 100 kg/cbm 11 up to 14 tonnes/hour Bale density (paper/newspapers) 400 to 550 kg/m³ Hydraulic oil tank capacity 600 litres PLC control Telemecanique TSX Micro Schneider Magelis control panel Effective transport dimensions excl. baler 8,125 x 2,300 x 3,000 mm (L x W x H) Transport weight press approx. 16 tonnes Condition of the baler: The machine was partial overhauled in our workshop and general maintenance work was carried out. After completion of the overhaul work, the press was tested during operation and is available for sale at short notice. The following overhaul work was carried out: General work: Machine cleaned, derusted, primed, partially painted Wire entry marks in the press channel feed-throughs welded shut and smoothed Hydraulic unit: Hydraulic oil tank emptied, tank cleaned, new oil filled Oil filter and air filter replaced Leaky oil sight glass on hydraulic oil tank replaced All hydraulic hoses replaced Electrics: English language installed in the programme menu Two key switches in the control panel replaced Control cabinet replaced Signal lamp on the control cabinet replaced Flaps end switch replaced Electrical system of the turbulator replaced, connected and tested Dljdou Thhrepfx Ab Toa Press ram: All four rollers removed from the press ram and replaced Main hydraulic cylinder dismantled, disassembled and partially overhauled, cylinder tube honed, complete seal set replaced, leak test performed All plastic wear pads on the press ram replaced Pre-press: Both bearings on the pre-press shaft replaced. Both hydraulic cylinders dismantled, disassembled and partially overhauled, both cylinder tubes honed, complete seal sets replaced, leak test performed. Scraper flap on the pre-press replaced. Binding system: Two complete needles with wire deflection rollers replaced Needles adjusted and set All wire deflection rollers in the needle heads replaced Drill fingers replaced Two drill shafts replaced All 8 wear plates on the Drillomat, under the drill fingers, replaced Scope of delivery: Only the baler will be sold. The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Year of construction: 2023, condition: new, Sell alligator shears ,cable shears , also for metal. Dedsku Ag Sspfx Ab Tela Model AS/250 Max. Cutting force 250 kN Cutting length 300 mm Max. Opening 160 mm Hyd. Pressure 15 MPa Full cycles p. minute 10-15 ×/min. Power consumption 5,5 kW Weight 450 Kg Size (L×W×H) 1200 × 980 × 1200

Year of construction: 2011, condition: good (used), Shredder system, single-shaft shredder, shredder, chipper, cutting mill, single-shaft crusher, rotor mill -Shredder system: completely made of stainless steel, for frozen meat or other -Motor power: 4 kW -Speed: approx. 60 rpm -Number of cutting knives: 10 pieces Dedpeh Di H Dofx Ab Tjla -Dimensions cutting blade: 250 mm -Filling spout 500 x 895 x H480 mm -Dimension 880/1390/H2060 mm -Weight 640 kg

Year of construction: 2023, condition: new, Mill for fine grinding of flour, coffee, dried vegetables, spices and more.. grinding range from 20-120mesh. capacity 100-400kg per hour. engine speed 3400 per min. machine weight 600kg. The power needed to operate the machine is 11kW. The machine has an additional dust filtration extraction. The whole machine is made of SUS304 stainless steel. PayPal payment available!!! Dledok S Rpujpfx Ab Tja

Year of construction: 2020, condition: new, DESCRIPTION Djdpsfz Nakofx Ab Tola The demineralized water station is used to produce the so-called demi water using ion exchange technology. The station consists of 3 columns Strongly acid cation exchanger working in the sodium cycle, Strongly basic anion exchanger working in the chloride cycle, Carbon filter Our RDI-2 / RDI-4 demineralization stations are equipped with fully automatic control heads. Rouezts The columns are made of AISI316L steel

Condition: new, machine/vehicle number: NEW-83, Vehicle transporter Mercedes Benz Atego rear axle air suspension * Power take-off * Driver's cab with 2 single seats * Sleeping area * Auxiliary heating * Radio/ CD * EC control unit * Lowerable rear Car transporter body DS12 [MODULO]: Double-decker body for transporting 2 cars or 1 van or camper van * Loading area lower platform approx. 700 x 255 cm. * Lifting platform approx. 450 x 240 cm. * Cable winch with radio and cable remote control * Hot-dip galvanized body Trailer: Air-braked BLYSS trailer for 3 cars. * Payload approx. 11,000 kg. * Loading area approx. 890 x 255 cm. * Rear approx. 150 cm. extendable * Lifting platform approx. 450 x 240 cm. * BPW axles * ABS * Trailer with perforated road plates * Vehicles can be secured in any position according to DIN * Trailer hot-dip galvanized Load securing is also available from us: Tensioning and lashing straps * Locking beams * Warning vests * Transport boxes * Edge protection * Dunnage bags * Wheel stoppers * etc. Djdpfx Aerwdr Aeb Tjla Financing and leasing possible We manufacture bodies of any size and type on any chassis. Tarpaulin, GRP sandwich, aluminum. Visit us at: Bodies - Complete vehicles - Trailers - Advice - Financing Subject to errors and prior sale, no liability for printing and input errors.

Condition: excellent (used), CATALOGUE NUMBER 6114 TECHNICAL DATA - Feed hopper inlet: 800x1000 mm - Rotor working width: 800 mm - Pump motor: 0.75 kW - Main motor: 15 kW - Number of knives: 21 pcs - Knife size: 30x30 mm - Screen: 0.8x10 mm - Pressure drawer - Electric auto-reverse - Discharge augers: 2×1.1 kW - Dimensions (L/W/H): 2460x1800x2250 mm - Weight: 1660 kg – German-made – Auto-reverse – Pressure drawer – Not painted – In very good condition – Used shredder Dledpfxognzd Ej Ab Tsa Net price: 63,900 PLN Net price: 15,200 EUR depending on the exchange rate, 4.2 EUR (Prices may vary with significant exchange rate fluctuations)

Year of construction: 2025, condition: new, BEFARD XP602 Glass Mounting Vacuum Suction Cup • Maximum load capacity 600 kg • 8 suction cups • Two-speed vacuum system Dsdpfsiauz Nex Ab Tela • Remote control for vacuum release • Battery powered • Manual rotation 360 degrees • Lock at every 90-degree rotation • Full vertical and horizontal adjustment Additional options: • HS spacers • spare battery • transport trolley • pallet box Other models available gripper with a load capacity of 300 kg, 450 kg, 800 kg, 900 kg, 1000 kg Available in the selected color

Year of construction: 2023, condition: new, Stock machine Dsdpfxohwdvcj Ab Tela Completely redeveloped high efficiency centrifuge based on our many years of production experience with the predecessor of this centrifuge, we have made various improvements with regard to maintenance costs, downtime and wear and tear parts.

Condition: new, power: 18 kW (24.47 HP), gearing type: mechanical, fuel type: diesel, color: blue, overall weight: 1,810 kg, total length: 2,895 mm, empty load weight: 1,300 kg, maximum load weight: 510 kg, suspension: other, number of seats: 1, Equipment: all wheel drive, differential lock, Power steering, diesel, all-wheel drive, 18.2 kW, 1,319 cm³, hydrostatic transmission, 3-cylinder, 20 km/h, differential lock, power steering, 1 seat, analog fuel gauge, rear swiveling work lights, 2 front weights at 15 kg each, roll bar with beacon, cross-ply tires front: 6.0-12, rear 8.30-20, overall length 2,895 mm, weight 1,300 kg, permissible total weight 1,810 kg. Turf tires available for an extra charge of €500.00 net. FOR US, CONDITION AND FEELING ARE DECISIVE; PRICE IS SECONDARY. For further questions, please contact Mr. Faller by phone. EXCHANGE, TRADE-IN, OR FINANCING OF YOUR VEHICLE POSSIBLE. All details provided without guarantee. For more offers, visit our homepage. The description and data provided do not constitute a warranty and are not binding. The only binding agreement is the purchase contract signed at our dealership. Subject to errors and prior sale! Dedewtpvzopfx Ab Tela