Tipper

Stas

Condition: used, empty load weight: 7,840 kg, maximum load weight: 28,160 kg, overall weight: 36,000 kg, axle configuration: 3 axles, first registration: 10/2015, loading space volume: 92 m³, suspension: air, tire size: 385/65 R22.5, Equipment: ABS, | STAS sliding floor | Type S300ZX, remote control | Tool box | 1 axle lift | Air suspension | Spare wheel holder | Unladen weight 7,840 kg, payload 28,160 kg | Tires: 385/65 R22.5 | SAF axles with disc brakes | Valid inspection report until 04/2026 | 10mm floor | Subject to errors, typing errors, and prior sale. Crodpfozr R A Rox Aqlof

Condition: used, maximum load weight: 34,780 kg, overall weight: 42,000 kg, axle configuration: 3 axles, first registration: 07/2019, loading space volume: 93 m³, Year of construction: 2019, Equipment: ABS, Well-maintained sliding floor semi-trailer. Has only been used to transport grain up to now. Equipment: Sliding floor in new condition Curtain side Platform for curtain side at the front wall Lift axle Aluminum Alco rims Individual wheel mudguards Raise and lower valve Electronic air control Moving wall Roof bows Cjdpfx Ajzr Tlnjqlerf Grain discharge slide in the rear door Crank support Toolbox 1 cable remote control 1 radio remote control Tire condition approx.: 70% Errors and prior sale excepted!!

Condition: used, axle configuration: 3 axles, first registration: 06/2024, loading space length: 8,900 mm, loading space width: 2,480 mm, loading space height: 2,200 mm, loading space volume: 49 m³, Lightweight chassis version Made of aluminum (15-6-12) Two fully automatically welded I-beam longitudinal members with welded cross members. Chassis width 1,600 mm Axles and suspension: 430 mm disc brake "off-road version" JOST (formerly DCA) axle assemblies, 3 x 9 tons with air suspension, air bellows in a central arrangement on the chassis longitudinal member. 1st axle can be lifted with starting aid and manual forced lowering, Smart Board infocenter, lift/lower valve, BVA brake wear indicator Tires and wheels: 6 wheels with tires size 385/65 R 22.5, approximately 60% tread, with steel rims 11.75 x 22.5 ET 120, universal wheel bolts for aluminum rims Kingpin: 2" screwed into an 8 mm thick plate "light" Landing gear: Landing gear with two speeds, 2x 20 tons support load for air suspension, we use swivel feet Braking system: According to E.E.G. standard, dual-line system Wabco, spring-loaded parking brake acting on two axles and Wabco EBS-E incl. RSS (Roll Stability System), Wabco Smartboard Infocenter, Aluminum air tank system Electrical system: According to STVZO guidelines with 2 five-chamber lights type Aspöck, 24-volt system with 2x7 and 1x 15-pole socket with side marker lights, 2 separate LED reversing lights 1 LED work light inside at the front All air and electrical lines are neatly routed in plastic pipes! Tipping body/dump body: interior fully welded Crjdpfx Aqozr Tcgeljf Aluminum dump body, side walls 30 mm thick plank profiles (2-3 mm) 600 mm wide, welded, floor 6 mm thick, highly wear-resistant alloy (5383H34/HB 110) with 45-degree angled profile to the side wall, front wall 4 mm thick, reinforced in an angled design, rear wall as a universal door in a straight design with 2-wing doors in a 2/3-1/3 design with a grain slide, ALURound profile for sealing the door gap on the rear doors, welded on the side and bottom, rear doors partially clad with aluminum, operation of the universal door automatically-pneumatically with a separate lever, lockable, rear supports made of aluminum, swivelable, two lower retainers with rubber buffers on the tipping body attached to the frame on the front wall Hydraulic system: tipping cylinder with "small" housing, suspension Hydraulic cylinder mounted on the front wall with a working pressure of 150 bar, manufactured by Edbro with approximately 2.5 m hydraulic hose and male coupling 1", tipping angle approx. 48 degrees Accessories: 6 Parlok fenders, complete splash guards over the entire vehicle width attached to the U-shaped protection, without spare wheel holder, aluminum, side underrun protection on the right in foldable design, toolbox type 860 large, approx. 3 m aluminum ladder, 3 aluminum swivel supports in the middle, raised by approx. 150 mm, additionally, a centrally mounted support receiver for positioning a total of 2 supports to increase the loading width, tarpaulin with a central light strip and separate reinforcements in the wear areas, quality approx. 660 g/m2 with tarpaulin system, continuous rubber cord in the rear end of the tarpaulin to be attached to two tension hooks on the swivel support at the rear, walkway on the frame in chassis color, tarpaulin closure with quick-release fastener, tarpaulin end at the rear with welded rubber cord against water ingress, robust foldable underrun protection in aluminum, 2 "Clear- Pass" splash guards on the fender according to EC standard, an aluminum grain chute with tarpaulin bag attached to the side on the frame, holder for shovel, broom and scrape

Condition: used, axle configuration: 3 axles, first registration: 09/2021, loading space length: 9,700 mm, loading space width: 2,480 mm, loading space height: 2,200 mm, loading space volume: 53 m³, Chassis, Light Version Aluminium (15-6-12) Two fully-automatically welded I-beam longitudinal members with welded cross members. Chassis width: 1,600 mm. Axles and Suspension: SAF-Intradisc light axle assemblies, 'off-road version', with 3 x 9 t disc brake axles (430 mm), SAF air suspension, centrally arranged to the chassis longitudinal members. 1st axle with liftable air bellows, starting aid and manual forced lowering. Smart Board Info Center, Hebert lowering valve, front load pressure gauge. Tyres and Wheels on Alloy Rims 6 wheels with tyres size 385/65 R 22.5 approx. 50% tread, 11.75 x 22.5 ET 120, UNI wheel bolts for alloy rims. Crodpfx Aezr Tcaoqlof Kingpin 2" screwed into an 8 mm thick 'light' plate. Landing Gear Support winches, load capacity 2 x 20 t, with swivel foot for air suspension. Braking System In accordance with E.G. standards, twin-line Wabco system, spring-actuated parking brake operating on two axles, with Wabco EBS-E including RSS (Roll Stability System), Wabco Smartboard Info Center, aluminium air reservoir system. Electrical System In compliance with StVZO guidelines, 3 round three-chamber lamps (Aspöck type), 24-volt system with 2x 7-pin and 1x 5-pin socket, 2x 7 side marker lamps, 2 central rear LED reverse lights, 1 round fog lamp, 4 LED work lights, 1 interior LED lamp, 4 red LED position lights in the door header. All air and electrical lines are neatly laid in plastic conduits. Tipper Body / Tipping Skip "Smooth Construction" Internal structure fully welded. Aluminium skip, side walls made from 30 mm thick plank profiles (2-3 mm), 600 mm wide and welded, floor plate 8 mm thick highly wear-resistant alloy (5383H34/HB 110) with 90-degree profile to side walls, front wall 4 mm reinforced in straight design, rear wall as universal door in straight design with 2 wing doors (1/2–1/2 configuration) and grain slide. Universal door operated automatically-pneumatically, separately lockable lever, rear frame in swing-out ALU design, two hold-downs with rubber buffers on the tipper skip fixed to the chassis at the front wall. Hydraulic System Tipping Cylinder with "Sheath" Suspension Hydraulic cylinder mounted on the front wall, operating pressure 150 bar, manufacturer Edbro, approx. 2.5 m hydraulic hose and loose end 1", tipping angle approx. 48 degrees. Accessories 6 Parlok mudguards, complete spray flaps across full vehicle width fixed to underrun protection, no spare wheel holder ALU, side underrun protection right side foldable, large tool box type 860, approx. 3 m aluminium ladder, 3 aluminium swing hoops in the centre approx. 150 mm elevated, additional central hoop support, roll tarp with central light strip and separate reinforcements in high wear areas, approx. 660 g/m² quality, tarp rolling system with quick tension closure, continuous rubber rope at rear edge with two tension hooks to be fastened to rear swing hoop, walkway on the chassis, rear tarp closure welded with rubber rope to prevent water ingress, robust folding underrun protection, 2 "Clear-Pass" spray flaps on mudguard (EG-compliant), aluminium grain funnel with sack fitted laterally to frame, holder for shovel, broom and scraper mounted above the axles, etc. Unladen weight: 5,950 kg Offer and images non-binding

Condition: used, axle configuration: 3 axles, first registration: 10/2023, loading space length: 8,900 mm, loading space width: 2,480 mm, loading space height: 2,200 mm, loading space volume: 48 m³, Lightweight chassis version Made of aluminum (15-6-12) Two fully automatically welded I-beams with welded crossmembers. Chassis width 1,600 mm Axles and suspension: Disc brake 430 mm "off-road version" Codpszr Tcyjfx Aqlerf JOST (formerly DCA) axle units, 3 x 9 tons, with air suspension, air bellows arranged centrally to the chassis longitudinal beam, 1st axle liftable with starting aid and manual forced lowering, Smart Board info center, lifting/lowering valve, BVA brake wear indicator Tires and wheels: 6 wheels with tires size 385/65 R 22.5, approx. 60% tread, with steel rims 11.75 x 22.5 ET 120, UNI wheel bolts, aluminum rims Kingpin: 2" - screwed into an 8 mm thick plate "light" Landing gear: Landing gears with two speeds, 2x 20 tons support load. We use swivel feet for air suspension. Braking system: According to E.E.G. standard, two-line system Wabco, spring-loaded parking brake acting on two axles and Wabco EBS-E incl. RSS (Roll-Stability System), Wabco Smartboard info center, Aluminum air tank system Electrical system: According to the guidelines of the STVZO (German Road Traffic Licensing Regulations) with 2 five-chamber lights, type Aspöck, 24-volt system with 2x 7 and 1x 15-pole socket with side marker lights, 2 sep. LED reversing lights 1 LED inside on the front wall All air and electrical lines are neatly routed in plastic pipes! Tipping body/dump bed: Fully welded interior Aluminum dump bed, side walls made of 30 mm thick plank profiles (2-3 mm) welded together, 600 mm wide, bottom made of 6 mm thick, highly wear-resistant alloy (5383H34/HB 110) with 45-degree angled profile to the side wall, front wall reinforced, 4 mm, in an angled design, rear wall as a universal door in a straight design with 2-wing doors in a 2/3-1/3 design with a grain slide, ALU round profile for sealing the door gap welded to the rear doors on the side and bottom, rear doors partially covered with smooth aluminum, operation of the universal door automatically-pneumatically with a separate lever that can be locked, rear support outriggers made of ALU, swiveling, two tie-down straps with rubber buffers attached to the frame on the front wall of the tipping bed, Hydraulic system: Tipping cylinder with "small" housing Hydraulic cylinder mounted on the front wall with a working pressure of 150 bar, manufacturer Edbro with approx. 2.5 m hydraulic hose and coupling half 1", tipping angle approx. 48 degrees Accessories: 6 Parlok fenders, complete splash guards over the entire vehicle width attached to the U-shaped protection, without spare wheel holder made of aluminum, side underrun protection on the right in a foldable design, toolbox type 860 large, approx. 3 m aluminum ladder, 3 aluminum swivel supports in the middle, raised by approx. 150 mm, additional centrally mounted support holder for positioning a total of 2 supports to increase the loading width, tarpaulin with a central light strip and separate reinforcements in the wear areas in approx. 660 gr./m2 quality with tarpaulin system, circumferential rubber cord in the rear end of the tarpaulin to be attached with two tension hooks on the swivel support at the rear, walkway on the frame in chassis color, tarpaulin closure with quick-release fastener, tarpaulin end at the rear with welded rubber cord to prevent water ingress, robust foldable underrun protection made of aluminum, 2 "Clear- Pass" splash guards on the fender according to EG standard, an aluminum grain chute with a tarpaulin bag attached to the side

Condition: used, axle configuration: 3 axles, first registration: 09/2008, loading space length: 9,700 mm, loading space width: 2,350 mm, loading space height: 2,165 mm, loading space volume: 50 m³, Chassis ALU chassis, aluminium alloy 5383H34 Two fully automatically welded T-profiles (width 200 mm) Cjdpfx Aqszr Tctelsrf Corrosion protection between steel and aluminium components, continuous rubber bonded under pressure onto the longitudinal beams for maximum stability via integrated tipping bearing shaft with wear-resistant, pressed-in special bushes, chassis width approx. 1,600 mm, air and electrical lines integrated in a plastic conduit. Axles and Suspension, Disc Brakes Jost-disc axle assemblies 3 x 9 tons with DCA air suspension, lift and lower valve, load pressure gauge, 3rd axle automatically liftable Tyres and Wheels 6 wheels fitted with 385/65 R 22.5 tyres approx. 50–60% tread remaining, on silver steel rims, 11.75x22.5 ET 120 Landing Gear Mechanical support legs, 2 x 20 ton load capacity, pivoting feet used for air suspension systems Brake System In compliance with EC standards, dual-circuit Wabco system, spring-loaded parking brake acting on two axles, EBS-E system Wabco 2S/2M, with RSS system (Roll Stability Support), aluminium air tanks Electrical System According to German Road Traffic Licensing Regulations (StVZO) with two five-chamber Aspöck LED lights, 24V system with two 7-pin and one 15-pin sockets at front, EBS socket, LED side marker lights, 2 clearance lights, 2 separate LED reversing lights Tipping Body / Bin ALU bin, side walls with welded vertical aluminium profiles, floor approx. 6 mm thick wear-resistant aluminium alloy (5383H34), Brinell HB 110, front wall sloped design in 4 mm ALU with reinforcement profiles for tipping cylinder mount, side walls in 3 mm hard alloy, straight rear wall, universal door with automatic-pneumatic (lockable) swinging and 2/3-1/3 split hinged tailgate, double linkage, manufactured from 4 mm aluminium, 1 grain chute with water protection, wear plates on sides approx. 400-1,000mm x 3,000mm x 4mm Hydraulic System Hydraulic cylinder mounted on front wall with working pressure 150 bar, make: Edbro, with approx. 2 m hydraulic hose and 1" loose half-coupling Accessories 6 Parlok plastic mudguards with 2 Stas mud flaps, 3 m aluminium ladder, reinforced underrun protection in folding execution with 2 towing eyes, 1x folding side guard, walkway on front wall with side access ladder (left), 3 ALU hoops in pivoting design, 1x centre hoop support, rolling tarpaulin with central aluminium tube, rolling tarpaulin system, tarpaulin approx. 660 g/m², quick-release fastener (without tension belts), wheel spanner, 2x wheel chocks, toolbox type 800, continuous splash guard mounted on underrun protection, etc. Offer and pictures subject to change.

Condition: used, empty load weight: 7,810 kg, maximum load weight: 28,190 kg, overall weight: 36,000 kg, axle configuration: 3 axles, first registration: 06/2025, next inspection (TÜV): 05/2027, loading space length: 13,513 mm, loading space width: 2,550 mm, loading space height: 2,641 mm, total length: 25,500 mm, total width: 39,960 mm, total height: 140,000 mm, suspension: air, tire size: 385/65 R 22,5, Year of construction: 2025, front tire size: 385/65 R 22,5, rear tire size: 385/65 R 22,5, emission class: none, Equipment: ABS, ABS, axle manufacturer SAF, aluminum chassis, color grey, air suspension with lift function, raising and lowering, loading volume 90, lift axle on 1st and 3rd axle, portal doors, disc brakes, fixed side underrun protection, toolbox, 2x LED reversing lights, 4x LED reversing lights on the sides (2x on the support gear and 2x behind the axle assembly), 1x LED spotlight inside the cargo area, broom and shovel holder on the left side underrun protection (in direction of travel), Cargofloor control type CF 500 SL-C - E"-CONTROL, 10mm ribbed, with additional plastic guides beneath the floor profiles, double wing doors (1/2 - 1/2 with upper door crossbar), radio remote control, rear door impact protection - aluminum buffers across the full width of the rear wall, roof bows and tarp, maintenance flap front left, working platform with access ladder, roll-up tarpaulin (PVC tarpaulin, Panama quality, 900g/m²), cargo securing certificate DIN EN 12642 Code XL, production 5/2025, like new condition!!! Csdozr Rwbjpfx Aqlorf

Condition: used, axle configuration: 3 axles, first registration: 05/2012, suspension: air, tire size: 385/65 R22.5, color: other, Year of construction: 2012, Axle configuration Tire size: 385/65 R22.5 Axle brand: Mercedes-Benz Brakes: Disc brakes Suspension: Air suspension Credozr E Rijpfx Aqlsf Rear axle 1: Lift axle; tire tread depth left: 8 mm; tire tread depth right: 5 mm Rear axle 2: Tire tread depth left: 7 mm; tire tread depth right: 7 mm Rear axle 3: Tire tread depth left: 10 mm; tire tread depth right: 10 mm Weights Unladen weight: 5,890 kg Payload: 32,110 kg GVW: 38,000 kg Condition Damage: None

Condition: used, axle configuration: 3 axles, first registration: 01/2018, loading space length: 8,500 mm, loading space width: 2,400 mm, loading space height: 1,500 mm, total length: 9,000 mm, total width: 2,500 mm, total height: 3,000 mm, suspension: air, tire size: 385/65R22,5, color: other, Year of construction: 2018, Equipment: ABS, = Additional Options and Accessories = - EBS - Alloy wheels = Notes = Number of axles: 3, Tare weight: 5360 kg, Gross vehicle weight: 39000 kg, Type of chassis: Full chassis, Chassis material: Steel, Kingpin size: 2 inch, Alloy wheels, Suspension type: Full air suspension, ABS, EBS, Body construction year: 2018, Body material: Aluminum, Side wall material: Aluminum, Drum volume: 28, Drum volume in: m3, Axle type: SAF, 28M3 alu, SAF, durabricht, Cramaro, lift axle etc. = Additional Information = General Information Cab: Day cab Registration number: KLEYN1 Drivetrain Fuel type: Diesel Transmission Gearbox: Manual gearbox Axle Configuration Tire size: 385/65R22.5 Brakes: Disc brakes Suspension: Air suspension Axle 1: Lift axle; Tire tread depth left: 9 mm; Tire tread depth right: 8 mm Axle 2: Tire tread depth left: 6 mm; Tire tread depth right: 6 mm Axle 3: Tire tread depth left: 8 mm; Tire tread depth right: 6 mm Weights Tare weight: 5,360 kg Payload: 33,640 kg GVWR: 39,000 kg Environment Emission class: Euro 0 Maintenance APK (Technical Inspection): valid until 01.2027 Crjdozqqw Sepfx Aqlef Condition Overall condition: average Technical condition: average Optical condition: average Damage: none = Company Information = Kleyn Trucks is one of the world's largest independent dealers in used vehicles. Here you can choose from a constantly changing stock of 1200 used trucks, tractors, and trailers. Our range includes all European brands from various years of construction and price ranges. Why buy from Kleyn Trucks? Simple! • Large, rapidly changing stock • Recognizable quality • A good price • Correct business practices • We speak many languages • We understand our customers • Assistance with import and transport • (Export) registration is quickly arranged • Expert technical services • The security of "recognizable quality" • And more.... Please visit our website for special offers and a complete inventory: Leasing through Kleyn Trucks is possible in most European countries! Quickly calculate your leasing rate and submit an inquiry through our website. Ask directly about our European warranty package.

Condition: good (used), axle configuration: 3 axles, first registration: 01/1990, suspension: air, tire condition: 50 %, color: other, Year of construction: 1990, Equipment: ABS, = Additional options and accessories = - air suspension - Drum brakes = More information = Crsdozrlvropfx Aqlof Tyre profile: 50% Brakes: drum brakes Suspension: air suspension Tipper: Back Technical condition: good Visual appearance: good