Spring Winding Machine - Automatic

SCHENKER FA-20 S

Condition: good (used), TECHNICAL DATA AXLE Rapid feed X,Y: 15000 mm/min Rapid feed A,B: 15000 mm/min Rapid feed Z1,Z2,E: 18000 mm/min Rapid feed C: 90000°/min Smallest input unit: 0.001 mm Smallest input unit, C-axis: 0.001° MACHINING PERFORMANCE Gedpfx Asu Uic Tog Rsiu Max. turning diameter: 20 mm Max. Headstock stroke: 205 mm Max. Drilling capacity: Stationary: 14 mm; Driven: 8 mm Max. Tapping capacity: Stationary: M10 x P1.5; Driven: M6 X P1.0 MAIN SPINDLE Spindle speed: 500 - 10000 rpm Drive: Spindle drive Main spindle motor: 3.7 / 5.5 kW Main spindle bore: 26 mm WHEELING SPINDLE Max. Clamping diameter: 20 mm Max. Part length for ejection to the front: 150 mm Max. Clamping length: 75 mm Spindle speed: 500 - 10000 rpm Pick-up spindle motor: 2.2 / 3.7 kW Indexing angle: 1°, 15° CONFIGURATION Operation mode: Right-handed Dimensions: 2700 x 1400 x 2400 mm Weight: 3400 kg SCOPE OF OFFER U.A: (list not exhaustive) Control system: Fanuc Fire extinguishing system: Siemens Oil mist separator: Donaldson Transformer Hydraulic unit Parts conveyor Chip conveyor Bar feeder: LNS Tool holder Exact scope of supply according to photo gallery We assume no liability for the correctness, completeness and up-to-dateness of the information.

Condition: ready for operation (used), Year of construction: 1989, An aluminum die casting system is available. Clamping force: 2200kN, opening force: 71kN, max. opening stroke: 430mm, mold closure: double toggle lever, pressure chamber: cold chamber, position: horizontal. Filling piston diameter min./max.: 40mm/70mm, pressure chamber filling volume min./max.: 293cm³/898cm³, casting pressure: 1990bar, blast area min./max.: 110cm²/338cm², output: 780 cycles/h. Clamping plate dimensions X/Y: 755mm/755mm, column spacing: 500mm/500mm, mold height min./max.: 250mm/600mm, min. mold dimensions X/Y: 296mm/296mm. Including crucible furnace, blow-out device, automatic dosing unit and 4x control cabinets. Documentation available. Giedpfsucfwpjx Ag Rju

Condition: new, 04P-023-LF 04P-023-RF 004P014-L-A2 004P014-R-A2 004P023-LF-A2 004P023-RF-A2 04P033-LF-A2 04P033-RF-A2 044P-023-011LF 044P-023-011RF 044P049-021-LF-A2 044P049-021-RF-A2 044P049-033-LF-A2 044P049-033-RF-A2 06P-094-LF-A2 06P-094-RF-A2 064P-079-025-LF 064P-079-025-RF 064P118-017-LF-A2 064P118-017-RF-A2 064P135–049–L-M1268 064P135–049–R-M1268 064P-135-049-LF 064P-135-049-RF 064P-148-034-LF 064P-148-034-RF 066P079-L-A1-M1077 066P079-R-A1-M1077 066P094-L-A1 066P094-R-A1 066P-104-031-LF 066P-104-031-RF 066P-118-035-LF 066P-118-035-RF 066P104-056-LF-A1 066P104-056-RF-A1 066P135-L-A1-M1077 066P135-R-A1-M1077 644P 079-037-014-LF-A2 (M1239) 644P 079-037-014-RF-A2 (M1239) 066P135-063-L-A1, 066P135-063-R-A1 644P-069-026-014-LF-A2-M1239 644P-069-026-014-RF-A2-M1239 664P118-056-017-L-A2- M929 M1256 664P118-056-017-R-A2- M929 M1256 Giedpfx Agjf Ddzqj Rju 08P-197-LF 08P-197-RF 086P-197-056-LF 086P-197-056-RF 886P-226-226-104-LF 886P-226-226-104-RF and other types, as one package

Condition: new, A dedicated machine for producing a straight trench / notch in a variety of timber products used in general joinery, garden furniture, shed, roof truss and timber frame manufacturing. Also can be used for door framing, notching of roof bearers and for log cabin manufacture.As standard the machine is fitted with horizontal pneumatic workpiece clamps and also a hydrocheck damper control to give a smooth stroke action to the cutterhead movement. Precision ball bearing movement on hardened steel runners. Sturdy cast iron construction with steel base stand. Gisdpfody Hm Djx Ag Rju 3kw motor. Max tool dia 250mm Bore of tool 40mm. Handwheel rise and fall of cutter motor arm. Max depth of trench / notch 60mm. Width of trench / notch 60mm - in one pass. Max. length of travel of tool 250mm. 2 x horizontal workpiece clamps. Hydrocheck damper to movement of cross cut arm. Dust extraction outlet 100mm. Machine stand

Condition: like new (used), Year of construction: 2024, Cantilever rack double-sided used: Hot-dip galvanized screw system Scope of delivery: 4 double-sided shelf stands, height 4,160 mm with foot section 1,200 mm 24 cantilevers with 1,200 mm depth, standard Including longitudinal and diagonal braces for 1,300 mm axle spacing Incl. fastening material (without ground anchors) - (*Delivery time approx. 1 week) - (*No damaged parts!) - (*Reorder spare parts and extension possible at any time) - (*Also available in larger quantities: 20 stands in stock) Detailed description: - Stable steel construction made of IPE profiles - Surface of all components hot-dip galvanized - Load capacity per stand side 2,250 kg - Load capacity per cantilever arm 750 kg - Cantilever arms height adjustable in 100 mm increments - 6 screwable cantilever arms per stand and 2 base sections with a depth of 1,200 mm, standard = 4 storage levels one above the other per side of the stand - Including longitudinal and diagonal braces for 1,300 mm spacing Gsdpfx Agoh Ek Daj Rjiu - Shelf length 4,000 mm - Including fastening material (without ground anchors) - With assembly instructions and load plates C4 in accordance with DIN standard - Expert advice by telephone - Made in Germany - Short delivery time - Collection on site possible Our cantilever racks are produced exclusively in Germany. We offer reliable freight with registration before delivery. The material is sensibly packed to enable easy unloading. When installed outdoors, the load-bearing capacity is reduced by the wind and snow load. The subsurface must be made of concrete, level and dowel-capable and must be able to bear the loads. The condition of the soil and load-bearing capacity as well as any official permits required must be checked and guaranteed by the customer. The shelf supports must be anchored to the floor on site; anchoring to the wall is not necessary and not recommended. According to the trade association, it is recommended that the shelf supports on the top storage level have a projection of at least 500 mm above the top edge of the supports.

Condition: excellent (used), Year of construction: 1967, Equippment: 1 Gripper feeding system right hand side 1 Eccentricpress 90 kN 2 Narrow-slide-units 3 Standard-slide-units Working range: Wire diameter range: 0,5 - 3,5 mm Gijdspq H Upjpfx Ag Reu Stripmetal width: max. 32 mm Feeding length: max. 170 mm Output: max. 250/min.

Condition: new, Year of construction: 2020, closing pressure 600 kN clamping plate 460x460 mm distance between columns 300x300 mm lock stroke 230 mm ejector stroke 70 mm capacity of ejector 40 kN height of form 120-350 mm Column diameter 56 mm casting capacity 54 kN Injection stroke 130 mm injection piston diameter 45, 50, 55 mm Casting volum 109. 150, 194 cm³ volume cast pressure 339. 274, 226 daN/cm² Casting area 176, 218, 264 cm² weight of the machine ca. 3,5 t Equipment of the machine 1.0.1 Cover for drop through area at the subframe 1.0.2 Cover for drop through area at the subframe with scale/chute 1.1.0 Motorized guard in casting direction left 1.4.0 Machine positioning mounting pads 1.5.4 Machine interior illumination 1.11.0 Convenience package energy efficiency 2.0.1 Ejector assistance packages 2.4.2 Securing of ejector platen 2.6.4 Machine assistance system SensiLock 2.8.0 Hydraulic adjustment of locking unit for shot positioning 3.1.1 Nitrogen pressure control for piston accumulator Gijdpfx Agjiu Smbs Rju 3.2.4 Multi-Chamber furnace with pump 3.2.5 Isolated Cover for Crucible Multi-chamber-furnace 3.4.4 Prefilling process 3.4.5 Simplified piston removal 3.4.6 Piston stop during return stroke 3.5.2 Electric nozzle and gooseneck heating (extended version) 4.5.0 Shut-off facility for hydraulic locking and injection unit 4.6.1.2 Integrated water circuit 2+4 circuits 5.1.0 Machine control DATADIALOG - Realtime Control (RC) 5.1.2 Convenience Package – Casting – 5.2.1 Ejector Pressure graphics in DATADIALOG control 5.4.1 Data logging Scope 5.4.2 Configurable In- and Outputs 5.6.0 Special cable lengths 6.1.3.1 Digital interface for Non-FRECH extractor (Dispo 10) 6.1.4 Serial interface for 4 heating-cooling circuits ROBAMAT 3.1 6.3.1.1 Hanging operating desk with monitor 6.5.2 Service Package RSD with Switch for each additional machine 7.2.2.2 Spraymotion 611 E with servo drive, 1-circuit 7.2.10 Extended spraying program for spraymotion 7.3.1 Lubricant container TD 20 7.4.0.2 Spray rail CR 245 7.12.3 Low noise chute

Condition: excellent (used), Year of construction: 1988, Krauss Maffei KM 250-900B Closing 250 TO Giodpfx Ajfp U Hveg Reu Year 1987 sprayed : 470 g Tie bars wide 63x56

Condition: used, Year of construction: 1996, functionality: fully functional, Graule ZS 170 saw, year 1996, 2,000 EUR Graule 6/250 - 160 spindle moulder, year 2008 2,700 EUR Rotary rack for sashes and frames 500 EUR Giodpfxewp Stze Ag Reu Roller conveyor 7.5 m as buffer for windows before glazing station 600 EUR

Condition: new, Year of construction: 2024, Automatic length measuring and positioning system for all STROMAB crosscut saws, as well as similar machines from other manufacturers. Gijdpfx Aexraucog Rsu It serves both as a stop and for workpiece positioning. Consists of: Aluminium profile 105 x 90 mm, anodized Toothed belt drive 32 mm, reinforced with steel wire Stepper motor 6 Nm, multi-voltage 115 - 230 V, 50/60 Hz Repeatability +/- 0.1 mm Positioning speed 60 m/min SMART 7 Control Unit with 7-inch touch screen Absolute and incremental processing mode 8 pre-set standard values 2 software versions with different optimization levels available optionally. ZM 415 – Usable working length 4,500 mm ZA333 – Roller table 4,500 x 280 mm, RD 32 mm ZA341 – Front support 4,500 x 260 mm ZA373 – Locking cable for customer’s own crosscut saw