ECOGLASS OPTICAL SORTER EGF-1500

PICVISA ECOGLASS OPTICAL SORTER EGF-1500

Condition: reconditioned (used), Year of construction: 2005, operating hours: 30,408 h, functionality: fully functional, pressing force: 50 t, filling opening width: 1,100 mm, filling opening length: 1,250 mm, bale width: 1,100 mm, bale height: 720 mm, bale weight: 550 kg, overall weight: 16,000 kg, oil tank capacity: 600 l, year of last overhaul: 2024, Technical data baler: Manufacturer Presona AB Type LP 50 EH1 Year of construction 2005 Operating hours 30,408 hours, as of April Number of pressed bales 198,059 as of April Pressing force main press 50 tonnes Specific pressing force 63 N/cm² Theoretical throughput capacity 530 m³/hour Throughput capacity under operating conditions 260 m³/hour Dimensions of feed chute 1,250 x 1,100 mm Bale chamber volume 2.2 m³ Bale dimensions 1,100 x 720 mm, variable length Drive power 22 kW Tying 5-fold vertical, fully automatic Throughput rates with a bulk density of 30 kg/cbm 6 up to 7 tonnes/hour Bulk weight of 50 kg/cbm 7 up to 9 tonnes/hour Bulk weight of 100 kg/cbm 11 up to 14 tonnes/hour Bale density (paper/newspapers) 400 to 550 kg/m³ Hydraulic oil tank capacity 600 litres PLC control Telemecanique TSX Micro Schneider Magelis control panel Effective transport dimensions excl. baler 8,125 x 2,300 x 3,000 mm (L x W x H) Transport weight press approx. 16 tonnes Condition of the baler: The machine was partial overhauled in our workshop and general maintenance work was carried out. After completion of the overhaul work, the press was tested during operation and is available for sale at short notice. The following overhaul work was carried out: General work: Machine cleaned, derusted, primed, partially painted Wire entry marks in the press channel feed-throughs welded shut and smoothed Hydraulic unit: Hydraulic oil tank emptied, tank cleaned, new oil filled Oil filter and air filter replaced Leaky oil sight glass on hydraulic oil tank replaced All hydraulic hoses replaced Electrics: English language installed in the programme menu Two key switches in the control panel replaced Control cabinet replaced Signal lamp on the control cabinet replaced Flaps end switch replaced Electrical system of the turbulator replaced, connected and tested Press ram: All four rollers removed from the press ram and replaced Main hydraulic cylinder dismantled, disassembled and partially overhauled, cylinder tube honed, complete seal set replaced, leak test performed All plastic wear pads on the press ram replaced Pre-press: Both bearings on the pre-press shaft replaced. Both hydraulic cylinders dismantled, disassembled and partially overhauled, both cylinder tubes honed, complete seal sets replaced, leak test performed. Scraper flap on the pre-press replaced. Binding system: Two complete needles with wire deflection rollers replaced Needles adjusted and set All wire deflection rollers in the needle heads replaced Drill fingers replaced Two drill shafts replaced All 8 wear plates on the Drillomat, under the drill fingers, replaced Gkodpeu Thhrefx Ag Dof Scope of delivery: Only the baler will be sold. The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: reconditioned (used), Year of construction: 2012, operating hours: 25,895 h, functionality: fully functional, pressing force: 78 t, filling opening width: 1,100 mm, filling opening length: 1,500 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 600 kg, overall weight: 24,000 kg, oil tank capacity: 1,000 l, power: 55 kW (74.78 HP), volume flow: 930 m³/h, Technical data baler: Manufacturer Presona AB Typ LP 80 VHK 1 Year of construction 2012 Total machine operating hours 25,895 hours, as of July 2025 Pump operating hours, effective 14,135 hours, as of July 2025 Number of bales pressed 235,597 pieces, as of July 2025 Press power main press 78,5 tons Specific press capacity 95 N/cm² Press power of pre-press 28 tons Volume of pressing chamber 2,7 m³ Feed channel1,500 x 1,100 mm Theoretic throughput rate 930 m³/h Throughput rate under operating conditions 410 m³/h Bale size 750 x 1,100 mm Driving motor 55 kW Tying system 5 fold vertical, 3-fold horizontal, full automatic Throughput rate with a bulk density of 30 kg/m³ approx. 9 to 12 tonnes/hour, depending on material 50 kg/m³ approx. 14 to 17 tonnes/hour, depending on material 100 kg/m³ approx. 16 to 25 tonnes/hour, depending on material Throughput capacity with MSW (Municipal Solid Waste) approx. 20 to 27 tonnes/hour, depending on material Gkodpfxovwlqqe Ag Def Bale weight 450 up to 600 kg, depends on material and bale length Volume hydraulic oil tank 1,000 l Baler dimensions built up with hopper 10,985 x 3,750 x 4,310 mm (l x w x h) Transport dimensions only baler 10,985 x 2,300 x 2,900 mm (L x w x h) Machine weight baler approx. 24 tons Condition of the press: The machine was partially overhauled and serviced in our workshop and, once the work was complete, tested in manual and automatic mode during operation. The following overhaul work was carried out: Machine cleaned, partially derusted and partially repainted Hydraulic oil tank emptied and cleaned Oil filter and air filter replaced, new hydraulic oil filled Press ram dismantled and cleaned All four rollers removed from the press ram and replaced Wire station with deflection rollers for the lower wire cleaned and made operational Side guides removed from the press ram, smoothed, mounted and readjusted Main hydraulic cylinder dismantled and disassembled for inspection Piston rod replaced, cylinder tube honed Complete seal set replaced, pressure test carried out Vertical and horizontal needle system for binding dismantled, cleaned, wire deflection rollers made functional and serviced Chain cleaned, greased, chain tension readjusted Drillomat cleaned, wire knife, drill shafts and drill fingers checked, retightened with torque and serviced Door contact switch checked and partially replaced. Emergency stop switch checked. Complete electrical wiring checked and partially replaced. Bearings of the wire guide rollers under the press replaced. New safety grilles for vertical and horizontal binding manufactured and installed. Machine checked, general maintenance work carried out and press tested in manual and automatic mode Scope of delivery: Only the baler will be sold. Comments: The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Year of construction: 2008, condition: excellent (used), 4x Machines available Gksdpfxomf Tk As Ag Dof Length 1150 mm Width 530 mm

Condition: excellent (used), Year of construction: 2015, operating hours: 14,900 h, functionality: fully functional, overall weight: 33,000 kg, power: 264 kW (358.94 HP), rotational speed (min.): 70 rpm, input voltage: 400 V, Slow-running, robust single-shaft shredder suitable for pre-shredding a wide variety of materials without solid contaminants. Application: Shredding of industrial and commercial waste, foils, packaging materials, textiles, paper, rubber, demolition wood, pallets, paper rolls, cable drums, and mixed plastics for thermal and recycling purposes, loose or baled. Lindner Jupiter 2200 Drive power: 2 x 132 kW (ABB motors) Screen perforation: According to customer requirements. mm Control cabinet: complete with (FU-ABB) Working opening: 2135 x 1750 mm Filling volume: approx. 5.5 m3 Gkodpjv S Hyvefx Ag Djf Rotor length: 2200 mm Rotor flight circle: 745 mm Rotor speed: 50 Hz: 87 rpm Number of rotor blades: 84 Blade shape: 172 x 57 x 28 mm Lower anvil blades: 6 Upper scraper combs: 6 Hydraulic feed: 11 kW Total weight: approx. 33 t Dimensions LxWxH mm: 5500 x 3050 x 3100 mm, with hopper H = 4880 mm Delivery time: immediately Two discharge belts available as an option.

Condition: like new (used), Year of construction: 2023, operating hours: 95 h, functionality: fully functional, total width: 2,950 mm, total length: 6,200 mm, total height: 4,530 mm, overall weight: 6,200 kg, belt width: 1,500 mm, fuel: electricity, input frequency: 50 Hz, type of input current: three-phase, input voltage: 400 V, transport height: 2,350 mm, transport length: 6,030 mm, transport width: 2,250 mm, Equipment: documentation/manual, Westeria mobile air separator type AirLift move for the separation of heavy and light materials. Typical applications in the recycling / waste management industry, for example for separating film from compost (fine or coarse grain) and mixed construction waste. Throughput capacity between 100-150 m³/h depending on material properties Working width: 1500 Gkodevrcigopfx Ag Def Color: RAL 3020 C3M RAL 7040 Including - DiscSpreader for optimum material distribution in the separator process - Pipe for blowing the lightweight material into on-site containers

Condition: used, Year of construction: 2012, power: 264 kW (358.94 HP), Stationary shredder M&J 4000S. Electric drive: 2x 132 kW 400 V AC, 50 Hz Godpfou Dkf Djx Ag Djkf Inkl. substructure, hydraulic unit, control cabinet.

Condition: good (used), Screen area: approx. 1,300 x 4,000 mm Gkedotpgvxspfx Ag Djf new semi-mobile steel construction

Condition: as good as new (ex-display), Year of construction: 2024, Set of shredding shafts manufactured NEW. These shafts are available with different knife configurations, the following are currently possible: Gkedpfxeivpkys Ag Def Size 450 / 650 / 750 / 850 / 950 5 / 6 / 7 / 8 / 9 / 10 knives possible 7 / 8 / 9 disks arivable for machine type VB-750 / VZ-750 / U-75 / HPS-1.5 / Pronar 2.8 / Inmpaktor 250 .. 300 / Titan ... We are also happy to meet your wishes. Please state your company address and contact details when making enquiries. This way we can prepare a quote and send it to your personal email.

Condition: good (used), functionality: fully functional, Conveyor belt length: approx. 28 m Discharge height: approx. 10 m Feed hopper capacity: approx. 10 m³ with adjustable dosing conveyor belt 2 transport conveyor belts (one flexible) on a 3-axle chassis Godpfxjv Scaxe Ag Dokf Powered by an ENDRESS 45 kVA generator

Condition: ready for operation (used), Drum Screen Terra Select plus feeding conveyors Gkodpfovnmcvox Ag Dof