Granulator / Shredder

Pallmann / Zerma PS 4 - 7,5 F

Condition: ready for operation (used), 🔧 Key Specifications Cutting System: Four-shaft configuration with two cutting shafts and two clearing shafts. Cutting Disc Diameter: Approximately 280 mm (11 inches). Gjdpfxownx Uis Ag Rouc Cutting Unit Dimensions: Working width of 1,000 mm and length of 700 mm. Hopper Opening: Approximately 1,400 mm x 1,600 mm. Motor Power: Typically equipped with two 18.5 kW motors. Operating Speed: Low-speed operation at around 25 rpm for high torque and reduced noise levels. Weight: Approximately 2,500 kg

Condition: excellent (used), Year of construction: 2010, power: 600 kW (815.77 HP), 1 burnt Weishaupt oil burner ----- Type : WM-L20 / 2-A Version : R Nox class : 2 Output : 600 - 2.100 kW Gusdpfeuugwcex Ag Rsc Oil throughput : 50 - 176 kg/h Year of construction : 2010 with WFM 100

Condition: used, Eldan Granulator HG129 Guedpfx Ajt Uyvreg Rsc

Condition: excellent (used), Year of construction: 1997, power: 1.5 kW (2.04 HP), Tria plastic grinder, shredder, granulator for sale in excellent condition make: TRIA 20-15/BL-T Power: 1.5kW, 50Hz, 380V Year of manufacture: 1997 Inlet opening: 200 x 230mm rotating knives 3 pcs standing knife: 1 pc Spout opening: 60mm Gsdpfx Aora N A Nsg Rsuc Final product size: 3-5mm Capacity: 30 kg/h approx.

Year of construction: 2011, condition: good (used), Shredder system, single-shaft shredder, shredder, chipper, cutting mill, single-shaft crusher, rotor mill -Shredder system: completely made of stainless steel, for frozen meat or other Gsdsh Di H Depfx Ag Rsuc -Motor power: 4 kW -Speed: approx. 60 rpm -Number of cutting knives: 10 pieces -Dimensions cutting blade: 250 mm -Filling spout 500 x 895 x H480 mm -Dimension 880/1390/H2060 mm -Weight 640 kg

Year of construction: 2008, condition: excellent (used), Oil burner Weishaupt WM-L10 Year :2008 Мы говорим по русски! Godoi Ap Atjpfx Ag Rjuc Viewing please only after telephone agreement! Preferred sale to dealers, traders or export. All information without guarantee, errors and prior sale reserved. The seller assumes no liability for typing and data transmission errors. Gladly we take your used boiler or burner in purchase! Of course we also take care of all formalities Loading possible

Condition: ready for operation (used), Slab recovery line with below machines: One 2-blade board edger One single blade horisontal resaw Conveyors system between the machines included. Gedpsgwqk Ssfx Ag Rsuc

Condition: excellent (used), Year of construction: 1995, operating hours: 45,000 h, pressure: 10 bar, operating pressure: 10 bar, For sale is a Loos steam boiler with Weishaupt oil burner. Gas burner available upon request. The unit is in very good condition. Model UL-S 5000, year of manufacture 1995. Steam output: 5,000 kg/h. Maximum steam pressure: 10 bar. Delivery available at extra cost. On-site inspection possible. Please contact us if you have any questions. Gjdpfx Ajydq I Sjg Reuc

Condition: reconditioned (used), Year of construction: 2007, operating hours: 22,605 h, functionality: fully functional, pressing force: 100 t, filling opening width: 1,100 mm, filling opening length: 1,600 mm, bale width: 1,100 mm, bale height: 1,100 mm, bale weight: 1,400 kg, overall weight: 36,000 kg, oil tank capacity: 1,300 l, year of last overhaul: 2025, For sale is a overhauled baler, with 100 tonnes pressing force, large format 1100 x 1100 mm, 75 kW drive power and 10-fold cross binding Technical data baler: Manufacturer Bollegraaf Typ HBC 110 K / 75 kW Year of construction 2007 Press power main press 100 tons Press power of pre-press 50 tons Gujdpfx Agovf E Avj Rjc Operating hours 22,605 hours Feed channel 1,600 x 1,100 mm Capacity per cycle time 3,15 m³ Theoretic cycle time 19 sec. Bale size 1,100 x 1,100 mm Driving motor 75 kW Connected load 126 kW Full load current 238 A Tying system 5-fold vertical, 5-fold horizontal, fully automated Throughput rate at a bulk weight of 30 kg/cbm approx.16 tons/h bulk weight of 50 kg/cbm approx. 25 tons/h bulk weight of 100 kg/cbm approx. 47 tons/h Bale weight up to 1400 kg, depends on material and bale lenght Volume oil tank approx. 1,300 l SPS controller Telemecanique TSX Micro Operating panel Schneider MAGELIS Touch Baler dimensions built up with hopper 11,750 x 5,000 x 7,105 mm (l x w x h) Transport dimensions only baler 11.750 x 2.500 x 3.450 mm (l x w x h) Machine weight baler approx. 36 tons Comments: The press was partially overhauled and serviced in our workshop and tested and stored after completion of the work. The machine is available at short notice and can be inspected in our warehouse by appointment. The following overhaul work was carried out: Rust removal and partial painting of the press. Remaining hydraulic oil tank drained, oil filter and air filter replaced. New hydraulic oil topped up. All hydraulic hoses replaced. Main hydraulic cylinder, two cylinders of the prepress flap and the cylinder of the press channel dismantled, disassembled, checked, cylinder tubes honed, all seal sets replaced and a final pressure test carried out. Disassembly of the prepress flap with bearings and bearing blocks. 1st and 3rd circular arc segmet cut out and a new one welded in again. Both bearings of the shaft of the prepress flap replaced. Upper material deflector on the frame of the prepress flap replaced. Press ram dismantled, checked and both front rollers replaced. Material deflectors and wear profiles on the sides and base of the press ram cut off and new ones welded in. Horizontal and vertical needle and tying unit dismantled, disassembled, checked, plastic sliding plates, bearings of the drill shafts and wire deflection rollers with bearings in the needle heads replaced. Both bronze slide rails on the left and right in the frame cover to the press ram replaced. Both wire deflection units on the left and right, with bale retaining clamps, completely renewed. Wire insertion unit including hydraulic cylinder under the needle feedthroughs completely renewed. Wire entry marks in the floor and side walls of the bale chamber welded shut and smoothed. General maintenance and service work carried out in accordance with the manufacturer's specifications. Press was tested in manual and automatic mode, accepted and stored after completion of overhaul work. We accept no liability for the technical specifications or any errors.

Condition: not inspected (used), Year of construction: 1985, functionality: fully functional, pressing force: 50 t, bale length: 1,000 mm, bale width: 750 mm, bale height: 750,750,750 mm, bale weight: 500 kg, input voltage: 400 V, overall weight: 7,500 kg, oil tank capacity: 500 l, power: 30 kW (40.79 HP), empty load weight: 7,500 kg, input frequency: 50 Hz, Manufacturer: Paal Typ: Pacomat V Year of construction: 1985 Press power main press: 50 t Specific press capacity: 5 kg/cm² Feed channel: 1.000 x 720mm (l x w) Gedpfx Agoic Rl Do Reuc Theoretic throughput rate: 200 cbm/h Bale size: 700 x 1.000 mm (w x h) length adjustable Driving motor: 30 kW Bale weight: approx. 500 kg Machine weight: approx. 8000kg The hydraulic unit is functional, the drive motor is in the removed state.