Gear motor 22 kW 127 rpm

Nord SK 62-180 L/4 SK 180 L / 4

Year of construction: 2017, condition: ready for operation (used), Material throughput: LDPE: 110kg/h, PA6.0/LDPE/EVOH: 150kg/h, PP/PA6.0/LDPE/EVOH: 135kg/h, PA6.0/LDPE: 120kg/h, EVA/LDPE: 150kg/h. Nominal output: 77kW, PCU output: 30kW, extruder output: 18.5kW, motor output: 10.7kW, heating zones: 1, heating output: 12kW. Documentation available. On-site inspection is possible. Lajdjwty Hkepfx Ap Asb

Condition: good (used), max. wheel diameter 1600 mm gear width 250 mm max. module 30 min. module 8 range of tooth size 58 mm tooth width 250 mm weight of the machine ca. 42,3 t dimensions of the machine ca. 4,45 x 6,00 m - Cone spacing in mm. for spiral angle 30° minimum: 150 maximum: 800 - Taper angle, in degrees minimum: 5 maximum: 85 - Tooth angle minimum: 0° maximum: 45° - Number of teeth to be cut minimum: 10 maximum: 150 Laedpfeu Dbucjx Ap Asb The machine is complete, fully functional and in good condition. Equipment / accessories: - complete set of change wheels - 4 pcs. cutter heads - various milling cutters - Operating instructions in English

Year of construction: 2013, condition: good (used), Used progressing cavity pump Manufacturer Netzsch Type: NM063BY04S18B Lsdpfx Aoillx Dsp Ajab Machine number: 459933 Year of construction: 2013 Output: 3.50 // 18 m3/h Speed: 91/288 min1/rpm Pressure: 16 // 0.10 bar Are you looking for a specific pump? We have other used pumps in stock - please ask us.

Condition: used, Technical details: pressure: 100 t daylight dimension : table/slide up: 800 mm throat: 360 mm ram stroke: 500 mm ram speed - forward: 200 m/s ram speed - reverse: 200 m/s Table dimensions: 750 x 560 x 90 mm passage inside table: Ø 26 mm clamping surface ram: BxT: 530 x 400 mm mortise hole in ram: Ø 50 mm cylinder diameter: Ø 250 mm height over floor: 720 mm total power requirement: 17,0 kW weight of the machine ca.: 5,5 t dimension machine xH: 1,8 x 1,2 x 3,2 m Lajdpfsvc Ax Nsx Ap Ajb

Condition: excellent (used), Year of construction: 2018, Geared motor, electric motor, electric geared motor, spur geared motor Lsdpfx Aet Drkysp Aoab -Manufacturer: SEW-Eurodrive, helical gearmotor -Type: R97/II2GD EDRN160L4/3GD/TZF/AL i18.24 -Speed: 1474/81 rpm at 50 Hz, see photo type plates -Power: 15 kW -Shaft: Ø 60 x 120 mm -Protection class: IP54 -Dimensions: 970/400/H370 mm -Weight: 231 kg

Condition: excellent (used), Year of construction: 1996, spindle bore: 160 mm, Swing over bed Ø 1040 mm Swing over cross slide Ø 710 mm Swing in the gap Ø 1580 mm DBC Turning Length 3000/4500 mm Gap length 1500 mm Spindle bore 160 mm Spindle power 40 kW Bed width 800 mm Spindle taper 6 Mk Lsdpfx Ajxtbf Ejp Ajab Workpiece weight 3500 Speeds / ranges 800 Rpm Feed rate X-Axis 10000 mm/min. Feed rate Z-Axis 10000 mm/min. Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Condition: good (used), Year of construction: 2001, - Manufacturer: IDE - Type: 45/4 - Year of manufacture: 2001 - Monovis Ø45mm 25LD Lajdpfx Aouhpiyop Ajb - Right-hand analog control - Screw profile: PVC - 4 heating zones on cylinder - 4 tool heating zones - Motor power: 8.5kW - Up to 60kg/h Good overall condition, very clean machine

Condition: excellent (used), Technical details Swing diameter over cross slide: 940 mm Turning diameter: 1,260 mm Speed (min.): 8 rpm Speed (max.): 900 rpm Overall height: 1,800 mm Overall length: 3,500 mm Overall width: 2,440 mm Three-jaw chuck diameter: 500 mm Centre distance: 3,500 mm Offer details VDF Wohlenberg Laodpfxoyr Sx Io Ap Ajb V1180 Centre distance: 3,500 mm 3.5 - 710 rpm 71 - 900 rpm Chuck: 500 mm diameter

Condition: used, MAZAK QT 20 Model: OT-20-N-K Turret: 8 positions Motor: 18.5 kW Lajdpswulzvofx Ap Aob Year: 1988 Weight: 11,700 lbs Chuck: diameter 250 renewed operational panel

Condition: excellent (used), Year of construction: 2006, operating hours: 53,244 h, functionality: fully functional, Technical Data – Gleason Phoenix II 600HC (CNC Hypoid Gear Cutting Machine) Working Area Max. workpiece diameter: Ø 600 mm Max. tooth depth: 24.6 mm Max. gear width: 110 mm Number of teeth: 1–300 Cutterhead size face milling (FM): 18" diameter Cutterhead size hobbing (FH): 210 mm radius Max. cutter spindle speed: 600 min⁻¹ Work Spindle Front taper diameter: Ø 203 mm Taper bore diameter: Ø 181 mm Bore depth: 884 mm Max. work spindle speed: 600 min⁻¹ Dimensions and Weight Footprint L × W × H: 4.4 × 3.5 × 3.5 m (incl. peripherals) Machine weight: 26,000 kg Connection Data Laedpjxwzu Isfx Ap Ajb Total connected load: 139 kVA Main fuse: 200 A Operating voltage: 400 V Mains frequency: 50 Hz Control voltage: 24 V DC