Used Kreissaege Feed for sale (11,216)

Condition: used, Single-column eccentric press EBU Type 75 SKU Machine no. No. P 4598462 Year of construction 1962 Compressive force 75 ton. throat depth 300 mm Table surface 800 x 620 mm waste hole 325 x 225 mm Plunger surface 470 x 180 mm Clamping pin bore Ø 40 mm Table height above floor 845 mm Stroke adjustment 16 - 140 mm Plunger adjustment 80 mm Installation height max. approx. 420 mm Stroke rate 60 + 105 strokes/min. Motor power 4 kW Mains connection 380 Volt, 50 Hz. - Pneumatic clutch/brake combination EBU - Overload protection with breaker plate in ram - UNIDOR tool monitoring system, type APS MINI - mechanically driven gripper feed with belt straightener OSTERKAMP, type ZPN 200/350 - strip width: 200 mm, feed length: max. 350 mm - Strip thickness: max. 3 mm or approx. 200 x 1.5 mm Pgedpfx Aodzqltjhvoi - 2 speeds due to 2 V-belt stages on the wheel transmission - Two-handed operation - Simple work area shielding for swinging open - Table height adjustment in lowest position = threaded spindles for adjustment 50 mm below floor level - Control cabinet and control panel for tool monitoring adjacent - Automatic central lubrication - 4 machine feet Space requirement L x W x H 2600 x 2300 x 2450 mm Weight approx. 5.5 tons good condition

Condition: used, Feeding technology / Feeding system / Vibratory feeder / Sorting unit / Bowl feeder Vibratory bowl, sorting device / Screw feeding with vibratory feeder for screw technology Feeding system DEPRAG Type: 0611-P/0.75-1S No.: 1183885 Year: 2011 - 2012 The system was used for feeding electrical connector pins. Product dimensions: Ø 4 mm, length 39 mm The pins are preloaded in the material hopper; the feed belt conveys the pins as required into the bowl feeder. From the bowl feeder, the product is transferred via the linear feeder to the product inverter. The product inverter orients the product into the correct position and makes it available for further processing. The unit comes from a prototype system; the external electrical control unit is not present and should be replaced by a PLC. Without modification, for example, suitable for the automatic and properly oriented feeding of threaded pins up to M4 x 40. The unit consists of the following components: 1 piece belt hopper / feed conveyor DEPRAG Type: B 10 Serial no.: 1178201 Order no.: 415050A Year: 2011 Fill volume: 10 liters Belt speed: 100 mm/min. Operating voltage: 24 V (DC) Pedpfx Aokpwuuohvogi - Belt surface dimpled - Foldable stainless steel chute Weight 11 kg 1 piece bowl feeder KENDRION Type: OA C006.504101 / OA C006029 / KQF 465 B5 Bowl diameter (top): 200 mm Bowl diameter (bottom): 100 mm Bowl internal height: approx. 75 mm Sorting track width: approx. 5 to 8 mm Operating voltage: 230 V, 50 Hz. 1 piece DEPRAG vibratory controller for the bowl feeder Type: SZG Controller 6 Serial no: 35 pieces linear feeder KENDRION Type: WS3B/36 Part no: WSB003,564025 Operating voltage: 230 V, 50 Hz. 1 piece DEPRAG vibratory controller for the linear feeder Type: SZG Controller 6 Serial no: 35 pieces product inverter FESTO with 180° swivel range - 1 piece FESTO valve block CPV10-VI 18200 - Compressed air requirement approx. 6 bar - 1 piece MURR base module type MVP12 - Complete unit mounted on a steel plate with 4 support legs Space requirements (L x W x H): 1150 x 520 x 860 mm Weight: 100 kg Very good condition

Condition: used, material width 200 mm material thickness - 6,0 mm feed length 0 - 120 mm Weight 0,40 t required space 0,9 x 0,8 x 0,7 m SPECIAL DEAL as is where is, WITHOUT putting into operation, in given condition Pgedpfx Ahovuuntovoi mechanical roll feed drive via main shaft / pivot shaft of the press - pivot shaft / mounting plate not included max. no. of strokes approx. 1500 / min

Condition: good (used), Wire feed drive for wire feeder case for MIG/MAG welding machine, MIG/MAG welding machine, wire feeder case, wire feeder, actuator, actuator, air damper actuator, geared motor Pjdpfxjrgbu Hj Ahvegi -Manufacturer: ELVI, actuator -Actuator: Type 100605 -Voltage: 24 V -Number: 6x drive units available -Price: per piece -Dimensions: 220/200/H120 mm -Weight: 1.9 kg/pc.

Condition: ready for operation (used), functionality: fully functional, Auction of a Joulin vacuum lifter with stacking function and infeed! The vacuum lifter is only 1.5 - 2 years old! The machine can be used as a standalone unit or as part of a complete line: - Bandsaw Canali ML 1100 TWIN F.L. 30 H.S. (Search ID: 21264817) - Wide planing machine Costa Planing Machine (Search ID: 21264937) TECHNICAL DETAILS Load capacity per layer: 300 kg MACHINE DETAILS Vacuum suction length: 6,000 mm Vacuum suction width: 1,400 mm Pgedpfxeyk Tife Ahvoi

Condition: new, Year of construction: 2026, Dimensions (L/W/H) 1400x2450x2800 mm Total pressure 400 to Pgsdpfx Ahsyk H Twovsi weight of the machine ca. 12000 kg

Condition: new, Year of construction: 2025, feed 2-22 m/min Weight 60 kg Total power requirement 0,4 kw Pgjdevz E Ukjpfx Ahvsi

Year of construction: 2000, condition: repair required (used), Feed transport equipment Pgededi Nykepfx Ahvei consisting of 1 piece conveyor belt and 1 piece roller conveyor ideal for (A) before planing machine with much hand saw (B) before cutting band saw or other saw (C) at the inlet before other machines in the state as is and without electrical control

Condition: excellent (used), Catalogue number 7670 TECHNICAL DATA - Track width: 340 mm - Roller width: 400 mm - Max. blade diameter for multi-blade saw: 350 mm - Blade bore diameter: 80 mm - Max. cutting height for edger: 100 mm - Max. cutting height for multi-blade saw: 120 mm - Table width with clearance: 900 mm - Table length: 1780 mm - From above: - Kickback fingers - Pressure roller, sliding, metal - Kickback fingers - Pressure roller, sliding - Saw shaft with blades Pgodpfx Ahsyk E Hpovoi - Pressure roller, sliding - Sliding pressure shaft, metal - From below: - Guide bar - Kickback fingers - Track - Central lubrication - Stepless feed speed adjustment - Electric lifting of saw shaft 0.75 kW + body 1.1 kW - Feed motor 1.5 kW - Main motor 22 kW - Floating saw movement 0.55 kW - Lasers (not working, require inspection) - Extraction port diameter: 210 mm - Overall dimensions (L/W/H): 2200 x 1450 x 2000 mm - Weight: 1925 kg ADVANTAGES – Made in Germany – Shaft with floating blade for edging – Additional sleeve for multi-blade saw included – Used multi-blade saw, in very good condition Net price: 58,900 PLN Net price: 14,030 EUR (based on exchange rate 4.2 EUR) (Prices may change with larger fluctuations)

Condition: new, Shaft diameter: 580working speed: 3-6motor power: 30length: 2760width: 2310heigth: 2680weight approx.: 14400 Technical specifications: Welded steel construction frame 3 rollers are driven Hardened and ground shafts made of high-strength special steel Rollers are hardened and ground Pedpfjh Alh Hex Ahvsgi Horizontal and vertical working position Hardened standard rollers Mobile control panel Angular side guide rollers Brake motor equipped for precision bending Digital displays (2 pieces) Options: Digital display STANDARD NC unit 10 screen EURO 11,500.00

Condition: good (used), Chuck flange, flange mount, chuck flange, drive flange, intermediate flange, chuck faceplate, mounting flange Podpsykpt Tofx Ahvegi -Muck flange: Mounting flange for three-jaw chucks, four-jaw chucks, faceplates -Outer diameter: 162 mm -Socket: Short cone 5, cone Ø 79 - 82 mm -Hole circle: Ø 105 x 10 mm / Ø 62 mm M10 -Passage: Ø 41 mm -Dimensions: Ø 162 x 48 mm -Weight: 4.7 kg

Condition: used, functionality: fully functional, Year of construction: 2017, 1x Mixer Holding Tank / Storage Container - Custom-made from V4A stainless steel - Used in our pellet production line as a buffer tank for herbal mixtures in powder form. It features a feed line (right side) from the mixer and a discharge on the left side to the intermediate storage tank. At the inlet from the mixer, there is also an option to divert the mixture into big bags prior to storage. - Material feed via electric auger (top) Pgedpfx Ahextmxwevsi - Material discharge via electric auger (angled) Filling capacity naturally varies depending on the type and volume of the mixture. With our mixtures, it held approximately 2 x 400 kg. All motors and sensors are fully functional.

Condition: like new (used), Chain feed table, used for feeding and linear transportation of roll goods or log goods. Forward/reverse run (reversing circuit) integrated, end positions are queried via roller limit switches. Pgodpfx Astw Sm Nohvoi Feeding length: 2200mm Feeding height: 950mm (adjustable) Drive power: 0.18kW (Getriebebau Nord) Condition: slight paint wear, otherwise as good as new

Condition: reconditioned (used), Technical data feed hopper with hydraulic moving floor and bag opener for recyclables from yellow bags and residual waste: Manufacturer BRT HARTNER GmbH Type HP5-3035 Year of construction 2015 Hopper volume 30 m³ Drive line 17.5 kW Dimensions in current state 13,200 x 3,050 x 4,350 mm (l x w x h) Condition of the machine: The feed hopper with bag opener was used at a large recycling plant, where recyclable materials from yellow bags or commercial waste were tipped into the hopper using wheel loaders, the bags were opened using the bag opener, and the recyclable materials were transported to a sorting plant or the commercial waste was transported in measured quantities for further processing. The system functioned flawlessly until it was dismantled and replaced with a larger system with higher throughput capacity. The machine was dismantled into individual parts in our workshop, partially overhauled, reassembled, and tested during operation. The following overhaul work was carried out and the following spare parts were replaced: Pgsdpfxsyizxrj Ahvji Dismantling of the feed hopper and bag opener into individual parts. Cleaning, partial sandblasting, priming and painting of the steel parts. Various wear and cover plates were newly manufactured and installed. Cutting off the worn ends (approx. 40cm) of the push floor pipes. Welding on the new pipes and smoothing the push floor pipes. Replacement of all plastic sliding plates for the hydraulic push floor. Removal of the hydraulic unit from the push floor, emptying of the hydraulic oil tank, replacement of the oil filters, refilling with new hydraulic oil. Replacement of the three hydraulic blocks, all valves, the oil sight glass and all hydraulic hoses from the hydraulic unit. The seal kit and hydraulic hoses were replaced on all three hydraulic cylinders of the push floor. All six limit switches (proximity sensors) on the push floor were replaced. The conveyor chains on the left and right of the scraper conveyor were replaced. Seven carrier bars on the scraper conveyor were replaced. The drive motor for the ripper blades was replaced. All nine pneumatic cylinders for the pressure pipes were replaced. All pneumatic lines and connections were replaced. All of the plastic sliding plates for the hydraulic operation of the bag opener were replaced. The bag opener can be moved vertically so that the system can also be used for commercial waste or residual waste without the bag opener. The side impact protection plates on both sides were replaced. Various wear parts of the bag opener have been replaced. The entire system has been rewired and reconnected. The system control in the control cabinet has been retrofitted by the manufacturer BRT Hartner to a self-sufficient individual control system and the standard programme has been reloaded into the control system. The system has been commissioned and tested by the manufacturer BRT Hartner, see the function video. Comments: The documentation (Manual, CE-declaration, electr./hydr.-drawings), are available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: as good as new (ex-display), Year of construction: 2025, functionality: fully functional, Leadscrew & feed shaft lathe DREHMA DA 410x1500 / New / Demonstration machine - CE marking - Digital readout - Swing over bed: 410 mm - Swing over cross slide: 225 mm - Swing in gap: 580 mm - Turning length: 1500 mm - Spindle bore: 52 mm - Speed range / gearbox: 45 - 1800 rpm Pgsdpfx Ajymcv Hehvei - Automatic longitudinal / cross feeds - Thread cutting / metric / imperial etc. - Tailstock MT 4 - Centralized lubrication - Motor power: 3.5 kW - Fixed & travelling steady rests - Multifix toolpost with inserts - 3-jaw chuck 200 mm - 4-jaw chuck 250 mm - Faceplate - Chuck guard - Coolant system - Work lamp - Live center & drill chuck - Machine feet - Documentation Dimensions LxWxH: 1.5 x 1 x 1.6 meters / Weight: 1850 kg Errors and omissions excepted.

Condition: excellent (used), CATALOG NO. 6916 TECHNICAL SPECIFICATIONS - Maximum workpiece width: 200 mm - Maximum workpiece height: 150 mm - 2 sanding units: Upper: steel roller + pad + steel roller Lower: steel roller + pad + steel roller From above: - Pressure roller, steel - Sanding unit - Sliding pressure roller, steel - Cleaning brush - Feed belt Pgedpfxjx Swtxe Ahvji From below: - Feed belt - 2 smooth sliding steel rollers - Sanding unit - Pressure roller, steel - Cleaning brush - Discharge roller - Electrically adjustable sanding height - Pneumatic oscillation of sanding belts - Infinitely variable feed speed regulation - Feed motor: 0.55 kW - Main motors: 2 x 4 kW - Air requirement: 6-8 bar - Extraction ports diameter: 3 x 80 mm, 1 x 120 mm - Overall dimensions (L/W/H): 1800 x 2070 x 2000 mm - Weight: 1422 kg – German manufacture, – unpainted – Very good condition, – used sander Net price: 25,900 PLN Net price: 6,160 EUR Net price calculated at an exchange rate of 4.2 PLN/EUR (price may change in case of significant exchange rate fluctuations)

Condition: ready for operation (used), DROOP & REIN SZ 100 / Keyway Broaching Machine for Lubrication Grooves Pgedpfjyl R Etjx Ahvoi - Maximum machinable diameter: 140 mm - Spindle bore: 40 mm - Groove length per stroke: 100 mm - Distance between chuck and tailstock center: 350 mm - 3 working speeds - Electric chuck guard - Good / fully operational condition Dimensions: LxWxH 0.9x0.6x1.5 meters / Weight: 300 kg Subject to errors and omissions

Condition: good (used), For sale: Colchester Triumph 2500 lathe, fully functional and ready for operation. The lathe is equipped with a Fagor digital readout and has a coolant pump installed beneath the chip tray. Technical data: Center height: 167 mm, Distance between centers: 635 mm, Swing over bed: 330 mm, Swing over cross slide: 210 mm, Spindle bore: 40 mm, Drive power: 2.2 kW. The sale includes 15 tool holders, a live center, and machine feet. Loading is problematic. Pedpfx Ahexw N I Nevogi

Condition: excellent (used), 20 pcs/stock Podpelgvpksfx Ahvogi Durkopp Adler 367 Triple Feed Sewing Machine Technical specifications : - automatic thread cutting - automatic lifting of the leg - automatic reinforcement - economic engine EFKA 220v The cars are refurbished in very good condition It is suitable for all types of thick materials: upholstery, leather, synthetic, etc Warranty & Delivery Component: complete de livery car The quality assurance of the machines is entirely conferred by our team of professional technicians. The machine is of superior quality, recommended for all types of workshops as well as for factories with medium and large productions. When purchasing th is machine, you have a 6-month warranty and a 5-year post-warranty. Delivery throughout the world!

Year of construction: 1968, condition: excellent (used), functionality: fully functional, STC-Ref:G-791-0181 WUPA Typ: KERMA TS-II, die cutting machine, Year: 1968 paper format: max. 624 x 890 mm equipped with: - speed: 36 strokes/min - Stroke punch for die cutting - die cutting thickness bis / up to 2,00 mm - 1.300 gr² - machine weight 4.500 kg - punch - German safety standard Pgjdpfxjxwn Nrj Ahvji --> available: 12/2025

Condition: used, Transnorm leading feed belt conveyor with overdrive GF 1720/1700/1650/1200/1000-700/600-600/500 RA2468 (NL-NB-GuB) Technical data: Conveyor length (NL): 1720, 1700, 1650, 1540, 1200, 1000 mm frame width (NB): 700 or 600 mm belt width (GuB): 600 or 500 mm Overall height (BH): 80 mm Angle: freely adjustable between 0 and 15° Supporting feet: optionally available Drive: overdrive Drive drum: Ø = 81 mm Belt return roller: Ø = 81 mm Optionally available: Supports Side guide on one side and on both sides Adjust length (longer/shorter) Pgjdeyi Ingjpfx Ahvei Prices net plus VAT ex central warehouse Dr. Sonntag GmbH & Co KG, 97076 Würzburg, Germany For individual, professional advice, simply contact us. Simply contact us by phone or e-mail. We will be happy to help you with the planning and implementation of your projects. We look forward to hearing from you. With kind regards Your team at Dr. Sonntag GmbH & Co. KG Your specialist and contact for intralogistics

Condition: used, Year of construction: 2008, Transnorm leading feed belt conveyor with overdrive GF 1720/1700/1650/1200/1000-700/600-600/500 RA2468 (NL-NB-GuB) Technical data: Conveyor length (NL): 1720, 1700, 1650, 1540, 1200, 1000 mm frame width (NB): 700 or 600 mm belt width (GuB): 600 or 500 mm Overall height (BH): 80 mm Angle: freely adjustable between 0 and 15° Supporting feet: optionally available Drive: overdrive Drive drum: Ø = 81 mm Belt return roller: Ø = 81 mm Optionally available: Supports Side guide on one side and on both sides Adjust length (longer/shorter) Prices net plus VAT ex central warehouse Dr. Sonntag GmbH & Co KG, 97076 Würzburg, Germany For individual, professional advice, simply contact us. Simply contact us by phone or e-mail. We will be happy to help you with the planning and implementation of your projects. We look forward to hearing from you. With kind regards Your team at Dr. Sonntag GmbH & Co. KG Pedsyi Inaopfx Ahvsgi Your specialist and contact for intralogistics

Condition: used, Transnorm leading feed belt conveyor with overdrive GF 1720/1700/1650/1200/1000-700/600-600/500 RA2468 (NL-NB-GuB) Technical data: Pgedoyi Inmspfx Ahvsi Conveyor length (NL): 1720, 1700, 1650, 1540, 1200, 1000 mm frame width (NB): 700 or 600 mm belt width (GuB): 600 or 500 mm Overall height (BH): 80 mm Angle: freely adjustable between 0 and 15° Supporting feet: optionally available Drive: overdrive Drive drum: Ø = 81 mm Belt return roller: Ø = 81 mm Optionally available: Supports Side guide on one side and on both sides Adjust length (longer/shorter) Prices net plus VAT ex central warehouse Dr. Sonntag GmbH & Co KG, 97076 Würzburg, Germany For individual, professional advice, simply contact us. Simply contact us by phone or e-mail. We will be happy to help you with the planning and implementation of your projects. We look forward to hearing from you. With kind regards Your team at Dr. Sonntag GmbH & Co. KG Your specialist and contact for intralogistics

Condition: excellent (used), CATALOG NUMBER 5799 TECHNICAL DATA - Maximum workpiece width: 230 mm - Maximum workpiece height: 140 mm - Minimum workpiece length: 300 mm - 2 sanding units: - Top and bottom + platen * Top: - 2 pressure rollers, slip type, metal - Pressure mechanism - Sanding unit: 2 metal rollers + platen - Slip-type pressure roller - Feed belt * Bottom: - Feed belt - 2 metal rollers, slip type, smooth Pgsdpsx Rqr Ssfx Ahvei - Pressure mechanism - Sanding unit: 2 metal rollers + platen - 3rd metal roller, slip type, smooth - Electrically adjustable sanding height - Oscillation of sanding belts - Pneumatic belt cleaning - Infinitely variable feed speed adjustment via inverter: 3–15 m/min - Feed motors: 2 × 0.37 kW - Main motors: - Upper: 5.5 kW - Lower: approx. 5.5 kW - Air requirement: 6–8 bar - Extraction nozzle diameter: 4 × 100 mm - Overall dimensions (L/W/H): 2340 × 1420 × 1920 mm - Weight: 1480 kg – Suitable for short workpieces (belts overlap) – German-manufactured – Very good condition – Not repainted – Used sander Net price: 22,900 PLN Net price: 5,450 EUR Net price calculated at 4.2 PLN/EUR (In case of significant exchange rate fluctuations, the price may change)

Condition: excellent (used), functionality: fully functional, power: 7.5 kW (10.20 HP), The pumps are suitable for supplying grinding oil for tool production. The pumps were in use up until recently on a central system. There are 2 units in stock. Pedpfx Ahoylqbuovsgi